[PATCH v2 2/5] gpio: qcom_pmic: rework pwrkey driver into a button driver
Caleb Connolly
caleb.connolly at linaro.org
Wed Nov 8 17:20:54 CET 2023
The power and resin keys were implemented as GPIOs here, but their only
use would be as buttons. Avoid the additional layer of introspection and
rework this driver into a button driver.
While we're here, replace the "qcom,pm8998-pwrkey" compatible with
"qcom,pm8941-pwrkey" to match upstream (Linux).
The dragonboard410c and 820c boards are adjusted to benefit from this
change too, simplify their custom board init code.
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
MAINTAINERS | 1 +
arch/arm/dts/dragonboard410c-uboot.dtsi | 14 +-
arch/arm/dts/dragonboard410c.dts | 22 ++-
arch/arm/dts/dragonboard820c-uboot.dtsi | 15 +--
arch/arm/dts/dragonboard820c.dts | 23 +++-
arch/arm/dts/dragonboard845c-uboot.dtsi | 11 --
arch/arm/dts/dragonboard845c.dts | 4 +
arch/arm/dts/sdm845.dtsi | 23 +++-
arch/arm/dts/starqltechn.dts | 20 +--
arch/arm/mach-snapdragon/Kconfig | 3 +
arch/arm/mach-snapdragon/init_sdm845.c | 45 ++-----
board/qualcomm/dragonboard410c/dragonboard410c.c | 31 ++---
board/qualcomm/dragonboard820c/dragonboard820c.c | 29 ++--
drivers/button/Kconfig | 9 ++
drivers/button/Makefile | 1 +
drivers/button/button-qcom-pmic.c | 165 +++++++++++++++++++++++
drivers/gpio/Kconfig | 3 +-
drivers/gpio/qcom_pmic_gpio.c | 104 --------------
18 files changed, 275 insertions(+), 248 deletions(-)
diff --git a/MAINTAINERS b/MAINTAINERS
index f6d63c8ab563..8cd102eaa070 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -572,6 +572,7 @@ M: Neil Armstrong <neil.armstrong at linaro.org>
R: Sumit Garg <sumit.garg at linaro.org>
S: Maintained
F: arch/arm/mach-snapdragon/
+F: drivers/button/button-qcom-pmic.c
F: drivers/clk/qcom/
F: drivers/gpio/msm_gpio.c
F: drivers/mmc/msm_sdhci.c
diff --git a/arch/arm/dts/dragonboard410c-uboot.dtsi b/arch/arm/dts/dragonboard410c-uboot.dtsi
index 3b0bd0ed0a1b..39b03a30702c 100644
--- a/arch/arm/dts/dragonboard410c-uboot.dtsi
+++ b/arch/arm/dts/dragonboard410c-uboot.dtsi
@@ -5,6 +5,9 @@
* (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski at gmail.com>
*/
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
/ {
smem {
@@ -42,14 +45,3 @@
gpios = <&pm8916_gpios 3 0>;
};
};
-
-
-&pm8916_pon {
- key_vol_down {
- gpios = <&pm8916_pon 1 0>;
- };
-
- key_power {
- gpios = <&pm8916_pon 0 0>;
- };
-};
diff --git a/arch/arm/dts/dragonboard410c.dts b/arch/arm/dts/dragonboard410c.dts
index 9230dd3fd96c..c41fee977813 100644
--- a/arch/arm/dts/dragonboard410c.dts
+++ b/arch/arm/dts/dragonboard410c.dts
@@ -147,11 +147,23 @@
#address-cells = <0x1>;
#size-cells = <0x1>;
- pm8916_pon: pm8916_pon at 800 {
- compatible = "qcom,pm8916-pwrkey";
- reg = <0x800 0x96>;
- #gpio-cells = <2>;
- gpio-controller;
+ pon at 800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x800 0x100>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
+ pm8916_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ debounce = <15625>;
+ bias-pull-up;
+ };
};
pm8916_gpios: pm8916_gpios at c000 {
diff --git a/arch/arm/dts/dragonboard820c-uboot.dtsi b/arch/arm/dts/dragonboard820c-uboot.dtsi
index 457728a43ecb..693c0e5efcc4 100644
--- a/arch/arm/dts/dragonboard820c-uboot.dtsi
+++ b/arch/arm/dts/dragonboard820c-uboot.dtsi
@@ -5,6 +5,9 @@
* (C) Copyright 2017 Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
*/
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
/ {
smem {
bootph-all;
@@ -30,15 +33,3 @@
};
};
};
-
-&pm8994_pon {
- key_vol_down {
- gpios = <&pm8994_pon 1 0>;
- label = "key_vol_down";
- };
-
- key_power {
- gpios = <&pm8994_pon 0 0>;
- label = "key_power";
- };
-};
diff --git a/arch/arm/dts/dragonboard820c.dts b/arch/arm/dts/dragonboard820c.dts
index ad201d48749c..0d9c9f7a4922 100644
--- a/arch/arm/dts/dragonboard820c.dts
+++ b/arch/arm/dts/dragonboard820c.dts
@@ -109,12 +109,23 @@
#address-cells = <0x1>;
#size-cells = <0x1>;
- pm8994_pon: pm8994_pon at 800 {
- compatible = "qcom,pm8994-pwrkey";
- reg = <0x800 0x96>;
- #gpio-cells = <2>;
- gpio-controller;
- gpio-bank-name="pm8994_key.";
+ pm8994_pon: pon at 800 {
+ compatible = "qcom,pm8916-pon";
+ reg = <0x800 0x100>;
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
+ pm8994_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ debounce = <15625>;
+ bias-pull-up;
+ };
};
pm8994_gpios: pm8994_gpios at c000 {
diff --git a/arch/arm/dts/dragonboard845c-uboot.dtsi b/arch/arm/dts/dragonboard845c-uboot.dtsi
index 7728f4f4a3e5..775f45c0149f 100644
--- a/arch/arm/dts/dragonboard845c-uboot.dtsi
+++ b/arch/arm/dts/dragonboard845c-uboot.dtsi
@@ -24,14 +24,3 @@
};
};
};
-
-&pm8998_pon {
- key_vol_down {
- gpios = <&pm8998_pon 1 0>;
- label = "key_vol_down";
- };
- key_power {
- gpios = <&pm8998_pon 0 0>;
- label = "key_power";
- };
-};
diff --git a/arch/arm/dts/dragonboard845c.dts b/arch/arm/dts/dragonboard845c.dts
index b4f057ac6537..054f253eb32a 100644
--- a/arch/arm/dts/dragonboard845c.dts
+++ b/arch/arm/dts/dragonboard845c.dts
@@ -41,4 +41,8 @@
};
};
+&pm8998_resin {
+ status = "okay";
+};
+
#include "dragonboard845c-uboot.dtsi"
diff --git a/arch/arm/dts/sdm845.dtsi b/arch/arm/dts/sdm845.dtsi
index 4798ace0ff8b..cd5d890e9a45 100644
--- a/arch/arm/dts/sdm845.dtsi
+++ b/arch/arm/dts/sdm845.dtsi
@@ -78,12 +78,25 @@
#address-cells = <0x1>;
#size-cells = <0x1>;
- pm8998_pon: pm8998_pon at 800 {
- compatible = "qcom,pm8998-pwrkey";
+ pm8998_pon: pon at 800 {
+ compatible = "qcom,pm8998-pon";
+
reg = <0x800 0x100>;
- #gpio-cells = <2>;
- gpio-controller;
- gpio-bank-name = "pm8998_key.";
+ mode-bootloader = <0x2>;
+ mode-recovery = <0x1>;
+
+ pm8998_pwrkey: pwrkey {
+ compatible = "qcom,pm8941-pwrkey";
+ debounce = <15625>;
+ bias-pull-up;
+ };
+
+ pm8998_resin: resin {
+ compatible = "qcom,pm8941-resin";
+ debounce = <15625>;
+ bias-pull-up;
+ status = "disabled";
+ };
};
pm8998_gpios: pm8998_gpios at c000 {
diff --git a/arch/arm/dts/starqltechn.dts b/arch/arm/dts/starqltechn.dts
index 5b6372bee79a..0842e19adb60 100644
--- a/arch/arm/dts/starqltechn.dts
+++ b/arch/arm/dts/starqltechn.dts
@@ -45,22 +45,6 @@
format = "a8r8g8b8";
};
- gpio-keys {
- compatible = "gpio-keys";
-
- key-pwr {
- label = "Power";
- linux,code = <KEY_ENTER>;
- gpios = <&pm8998_pon 0 GPIO_ACTIVE_LOW>;
- };
-
- key-vol-down {
- label = "Volume Down";
- linux,code = <KEY_DOWN>;
- gpios = <&pm8998_pon 1 GPIO_ACTIVE_LOW>;
- };
- };
-
soc: soc {
serial at a84000 {
status = "okay";
@@ -68,6 +52,10 @@
};
};
+&pm8998_resin {
+ status = "okay";
+};
+
&tlmm {
muic_i2c: muic-i2c-n {
pins = "GPIO_33", "GPIO_34";
diff --git a/arch/arm/mach-snapdragon/Kconfig b/arch/arm/mach-snapdragon/Kconfig
index 3c9f3bee3f18..ad6671081910 100644
--- a/arch/arm/mach-snapdragon/Kconfig
+++ b/arch/arm/mach-snapdragon/Kconfig
@@ -17,6 +17,7 @@ config SDM845
select LINUX_KERNEL_IMAGE_HEADER
imply CLK_QCOM_SDM845
imply PINCTRL_QCOM_SDM845
+ imply BUTTON_QCOM_PMIC
config LNX_KRNL_IMG_TEXT_OFFSET_BASE
default 0x80000000
@@ -30,6 +31,7 @@ config TARGET_DRAGONBOARD410C
select ENABLE_ARM_SOC_BOOT0_HOOK
imply CLK_QCOM_APQ8016
imply PINCTRL_QCOM_APQ8016
+ imply BUTTON_QCOM_PMIC
help
Support for 96Boards Dragonboard 410C. This board complies with
96Board Open Platform Specifications. Features:
@@ -45,6 +47,7 @@ config TARGET_DRAGONBOARD820C
bool "96Boards Dragonboard 820C"
imply CLK_QCOM_APQ8096
imply PINCTRL_QCOM_APQ8096
+ imply BUTTON_QCOM_PMIC
help
Support for 96Boards Dragonboard 820C. This board complies with
96Board Open Platform Specifications. Features:
diff --git a/arch/arm/mach-snapdragon/init_sdm845.c b/arch/arm/mach-snapdragon/init_sdm845.c
index 1f8850239437..067acc9a6f44 100644
--- a/arch/arm/mach-snapdragon/init_sdm845.c
+++ b/arch/arm/mach-snapdragon/init_sdm845.c
@@ -5,6 +5,7 @@
* (C) Copyright 2021 Dzmitry Sankouski <dsankouski at gmail.com>
*/
+#include <button.h>
#include <init.h>
#include <env.h>
#include <common.h>
@@ -32,46 +33,18 @@ __weak int board_init(void)
/* Check for vol- and power buttons */
__weak int misc_init_r(void)
{
- struct udevice *pon;
- struct gpio_desc resin;
- int node, ret;
+ struct udevice *btn;
+ int ret;
+ enum button_state_t state;
- ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8998_pon at 800", &pon);
+ ret = button_get_by_label("pwrkey", &btn);
if (ret < 0) {
- printf("Failed to find PMIC pon node. Check device tree\n");
- return 0;
+ printf("Couldn't find power button!\n");
+ return ret;
}
- node = fdt_subnode_offset(gd->fdt_blob, dev_of_offset(pon),
- "key_vol_down");
- if (node < 0) {
- printf("Failed to find key_vol_down node. Check device tree\n");
- return 0;
- }
- if (gpio_request_by_name_nodev(offset_to_ofnode(node), "gpios", 0,
- &resin, 0)) {
- printf("Failed to request key_vol_down button.\n");
- return 0;
- }
- if (dm_gpio_get_value(&resin)) {
- env_set("key_vol_down", "1");
- printf("Volume down button pressed\n");
- } else {
- env_set("key_vol_down", "0");
- }
-
- node = fdt_subnode_offset(gd->fdt_blob, dev_of_offset(pon),
- "key_power");
- if (node < 0) {
- printf("Failed to find key_power node. Check device tree\n");
- return 0;
- }
- if (gpio_request_by_name_nodev(offset_to_ofnode(node), "gpios", 0,
- &resin, 0)) {
- printf("Failed to request key_power button.\n");
- return 0;
- }
- if (dm_gpio_get_value(&resin)) {
+ state = button_get_state(btn);
+ if (state == BUTTON_ON) {
env_set("key_power", "1");
printf("Power button pressed\n");
} else {
diff --git a/board/qualcomm/dragonboard410c/dragonboard410c.c b/board/qualcomm/dragonboard410c/dragonboard410c.c
index 371b3262f8c5..350e0e9e20aa 100644
--- a/board/qualcomm/dragonboard410c/dragonboard410c.c
+++ b/board/qualcomm/dragonboard410c/dragonboard410c.c
@@ -5,6 +5,7 @@
* (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski at gmail.com>
*/
+#include <button.h>
#include <common.h>
#include <cpu_func.h>
#include <dm.h>
@@ -108,32 +109,20 @@ int board_usb_init(int index, enum usb_init_type init)
/* Check for vol- button - if pressed - stop autoboot */
int misc_init_r(void)
{
- struct udevice *pon;
- struct gpio_desc resin;
- int node, ret;
+ struct udevice *btn;
+ int ret;
+ enum button_state_t state;
- ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8916_pon at 800", &pon);
+ ret = button_get_by_label("vol_down", &btn);
if (ret < 0) {
- printf("Failed to find PMIC pon node. Check device tree\n");
- return 0;
+ printf("Couldn't find power button!\n");
+ return ret;
}
- node = fdt_subnode_offset(gd->fdt_blob, dev_of_offset(pon),
- "key_vol_down");
- if (node < 0) {
- printf("Failed to find key_vol_down node. Check device tree\n");
- return 0;
- }
-
- if (gpio_request_by_name_nodev(offset_to_ofnode(node), "gpios", 0,
- &resin, 0)) {
- printf("Failed to request key_vol_down button.\n");
- return 0;
- }
-
- if (dm_gpio_get_value(&resin)) {
+ state = button_get_state(btn);
+ if (state == BUTTON_ON) {
env_set("preboot", "setenv preboot; fastboot 0");
- printf("key_vol_down pressed - Starting fastboot.\n");
+ printf("vol_down pressed - Starting fastboot.\n");
}
return 0;
diff --git a/board/qualcomm/dragonboard820c/dragonboard820c.c b/board/qualcomm/dragonboard820c/dragonboard820c.c
index 6785bf58e949..2f0db628368b 100644
--- a/board/qualcomm/dragonboard820c/dragonboard820c.c
+++ b/board/qualcomm/dragonboard820c/dragonboard820c.c
@@ -5,6 +5,7 @@
* (C) Copyright 2017 Jorge Ramirez-Ortiz <jorge.ramirez-ortiz at linaro.org>
*/
+#include <button.h>
#include <cpu_func.h>
#include <init.h>
#include <env.h>
@@ -139,30 +140,18 @@ void reset_cpu(void)
/* Check for vol- button - if pressed - stop autoboot */
int misc_init_r(void)
{
- struct udevice *pon;
- struct gpio_desc resin;
- int node, ret;
+ struct udevice *btn;
+ int ret;
+ enum button_state_t state;
- ret = uclass_get_device_by_name(UCLASS_GPIO, "pm8994_pon at 800", &pon);
+ ret = button_get_by_label("pwrkey", &btn);
if (ret < 0) {
- printf("Failed to find PMIC pon node. Check device tree\n");
- return 0;
+ printf("Couldn't find power button!\n");
+ return ret;
}
- node = fdt_subnode_offset(gd->fdt_blob, dev_of_offset(pon),
- "key_vol_down");
- if (node < 0) {
- printf("Failed to find key_vol_down node. Check device tree\n");
- return 0;
- }
-
- if (gpio_request_by_name_nodev(offset_to_ofnode(node), "gpios", 0,
- &resin, 0)) {
- printf("Failed to request key_vol_down button.\n");
- return 0;
- }
-
- if (dm_gpio_get_value(&resin)) {
+ state = button_get_state(btn);
+ if (state == BUTTON_ON) {
env_set("bootdelay", "-1");
printf("Power button pressed - dropping to console.\n");
}
diff --git a/drivers/button/Kconfig b/drivers/button/Kconfig
index 8ce2de37d62a..097b05f822e7 100644
--- a/drivers/button/Kconfig
+++ b/drivers/button/Kconfig
@@ -27,4 +27,13 @@ config BUTTON_GPIO
The GPIO driver must used driver model. Buttons are configured using
the device tree.
+config BUTTON_QCOM_PMIC
+ bool "Qualcomm power button"
+ depends on BUTTON
+ depends on PMIC_QCOM
+ help
+ Enable support for the power and "resin" (usually volume down) buttons
+ on Qualcomm SoCs. These will be configured as the Enter and Down keys
+ respectively, allowing navigation of bootmenu with buttons on device.
+
endmenu
diff --git a/drivers/button/Makefile b/drivers/button/Makefile
index bbd18af14940..68555081a47a 100644
--- a/drivers/button/Makefile
+++ b/drivers/button/Makefile
@@ -5,3 +5,4 @@
obj-$(CONFIG_BUTTON) += button-uclass.o
obj-$(CONFIG_BUTTON_ADC) += button-adc.o
obj-$(CONFIG_BUTTON_GPIO) += button-gpio.o
+obj-$(CONFIG_BUTTON_QCOM_PMIC) += button-qcom-pmic.o
\ No newline at end of file
diff --git a/drivers/button/button-qcom-pmic.c b/drivers/button/button-qcom-pmic.c
new file mode 100644
index 000000000000..34a976d1e6c6
--- /dev/null
+++ b/drivers/button/button-qcom-pmic.c
@@ -0,0 +1,165 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Qualcomm generic pmic gpio driver
+ *
+ * (C) Copyright 2015 Mateusz Kulikowski <mateusz.kulikowski at gmail.com>
+ * (C) Copyright 2023 Linaro Ltd.
+ */
+
+#include <button.h>
+#include <dt-bindings/input/linux-event-codes.h>
+#include <dm.h>
+#include <dm/device-internal.h>
+#include <dm/lists.h>
+#include <log.h>
+#include <power/pmic.h>
+#include <spmi/spmi.h>
+#include <linux/bitops.h>
+
+#define REG_TYPE 0x4
+#define REG_SUBTYPE 0x5
+
+struct qcom_pmic_btn_priv {
+ u32 base;
+ u32 status_bit;
+ int code;
+ struct udevice *pmic;
+};
+
+#define PON_INT_RT_STS 0x10
+#define KPDPWR_ON_INT_BIT 0
+#define RESIN_ON_INT_BIT 1
+
+#define NODE_IS_PWRKEY(node) (!strncmp(ofnode_get_name(node), "pwrkey", strlen("pwrkey")))
+#define NODE_IS_RESIN(node) (!strncmp(ofnode_get_name(node), "resin", strlen("resin")))
+
+static enum button_state_t qcom_pwrkey_get_state(struct udevice *dev)
+{
+ struct qcom_pmic_btn_priv *priv = dev_get_priv(dev);
+
+ int reg = pmic_reg_read(priv->pmic, priv->base + PON_INT_RT_STS);
+
+ if (reg < 0)
+ return 0;
+
+ return (reg & BIT(priv->status_bit)) != 0;
+}
+
+static int qcom_pwrkey_get_code(struct udevice *dev)
+{
+ struct qcom_pmic_btn_priv *priv = dev_get_priv(dev);
+
+ return priv->code;
+}
+
+static int qcom_pwrkey_probe(struct udevice *dev)
+{
+ struct button_uc_plat *uc_plat = dev_get_uclass_plat(dev);
+ struct qcom_pmic_btn_priv *priv = dev_get_priv(dev);
+ ofnode node = dev_ofnode(dev);
+ int ret;
+ u64 base;
+
+ /* Ignore the top-level pon node */
+ if (!uc_plat->label)
+ return 0;
+
+ /* the pwrkey and resin nodes are children of the "pon" node, get the
+ * PMIC device to use in pmic_reg_* calls.
+ */
+ priv->pmic = dev->parent->parent;
+
+ /* Get the address of the parent pon node */
+ base = dev_read_addr(dev->parent);
+ if (base == FDT_ADDR_T_NONE) {
+ printf("%s: Can't find address\n", dev->name);
+ return -EINVAL;
+ }
+
+ priv->base = base;
+
+ /* Do a sanity check */
+ ret = pmic_reg_read(priv->pmic, priv->base + REG_TYPE);
+ if (ret != 0x1 && ret != 0xb) {
+ printf("%s: unexpected PMIC function type %d\n", dev->name, ret);
+ return -ENXIO;
+ }
+
+ ret = pmic_reg_read(priv->pmic, priv->base + REG_SUBTYPE);
+ if ((ret & 0x7) == 0) {
+ printf("%s: unexpected PMCI function subtype %d\n", dev->name, ret);
+ return -ENXIO;
+ }
+
+ if (NODE_IS_PWRKEY(node)) {
+ priv->status_bit = 0;
+ priv->code = KEY_ENTER;
+ } else if (NODE_IS_RESIN(node)) {
+ priv->status_bit = 1;
+ priv->code = KEY_DOWN;
+ } else {
+ /* Should not get here! */
+ printf("Invalid pon node '%s' should be 'pwrkey' or 'resin'\n",
+ ofnode_get_name(node));
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static int button_qcom_pmic_bind(struct udevice *parent)
+{
+ struct udevice *dev;
+ ofnode node;
+ int ret;
+
+ dev_for_each_subnode(node, parent) {
+ struct button_uc_plat *uc_plat;
+ const char *label;
+
+ if (!ofnode_is_enabled(node))
+ continue;
+
+ ret = device_bind_driver_to_node(parent, "qcom_pwrkey",
+ ofnode_get_name(node),
+ node, &dev);
+ if (ret) {
+ printf("Failed to bind %s! %d\n", label, ret);
+ return ret;
+ }
+ uc_plat = dev_get_uclass_plat(dev);
+ if (NODE_IS_PWRKEY(node)) {
+ uc_plat->label = "pwrkey";
+ } else if (NODE_IS_RESIN(node)) {
+ uc_plat->label = "vol_down";
+ } else {
+ printf("Unknown button node '%s' should be 'pwrkey' or 'resin'\n",
+ ofnode_get_name(node));
+ device_unbind(dev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct button_ops button_qcom_pmic_ops = {
+ .get_state = qcom_pwrkey_get_state,
+ .get_code = qcom_pwrkey_get_code,
+};
+
+static const struct udevice_id qcom_pwrkey_ids[] = {
+ { .compatible = "qcom,pm8916-pon" },
+ { .compatible = "qcom,pm8941-pon" },
+ { .compatible = "qcom,pm8998-pon" },
+ { }
+};
+
+U_BOOT_DRIVER(qcom_pwrkey) = {
+ .name = "qcom_pwrkey",
+ .id = UCLASS_BUTTON,
+ .of_match = qcom_pwrkey_ids,
+ .bind = button_qcom_pmic_bind,
+ .probe = qcom_pwrkey_probe,
+ .ops = &button_qcom_pmic_ops,
+ .priv_auto = sizeof(struct qcom_pmic_btn_priv),
+};
diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index ba42b0768e12..fbf77673c5e0 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -309,12 +309,13 @@ config CMD_PCA953X
config QCOM_PMIC_GPIO
bool "Qualcomm generic PMIC GPIO/keypad driver"
depends on DM_GPIO && PMIC_QCOM
+ select BUTTON
help
Support for GPIO pins and power/reset buttons found on
Qualcomm SoCs PMIC.
Default name for GPIO bank is "pm8916".
Power and reset buttons are placed in "pwkey_qcom" bank and
- have gpio numbers 0 and 1 respectively.
+ have gpio numbers 0 and 1 respectively.
config PCF8575_GPIO
bool "PCF8575 I2C GPIO Expander driver"
diff --git a/drivers/gpio/qcom_pmic_gpio.c b/drivers/gpio/qcom_pmic_gpio.c
index e5841f502953..7b83c67fa464 100644
--- a/drivers/gpio/qcom_pmic_gpio.c
+++ b/drivers/gpio/qcom_pmic_gpio.c
@@ -275,107 +275,3 @@ U_BOOT_DRIVER(qcom_pmic_gpio) = {
.priv_auto = sizeof(struct qcom_gpio_bank),
};
-
-/* Add pmic buttons as GPIO as well - there is no generic way for now */
-#define PON_INT_RT_STS 0x10
-#define KPDPWR_ON_INT_BIT 0
-#define RESIN_ON_INT_BIT 1
-
-static int qcom_pwrkey_get_function(struct udevice *dev, unsigned offset)
-{
- return GPIOF_INPUT;
-}
-
-static int qcom_pwrkey_get_value(struct udevice *dev, unsigned offset)
-{
- struct qcom_gpio_bank *priv = dev_get_priv(dev);
-
- int reg = pmic_reg_read(dev->parent, priv->pid + PON_INT_RT_STS);
-
- if (reg < 0)
- return 0;
-
- switch (offset) {
- case 0: /* Power button */
- return (reg & BIT(KPDPWR_ON_INT_BIT)) != 0;
- break;
- case 1: /* Reset button */
- default:
- return (reg & BIT(RESIN_ON_INT_BIT)) != 0;
- break;
- }
-}
-
-/*
- * Since pmic buttons modelled as GPIO, we need empty direction functions
- * to trick u-boot button driver
- */
-static int qcom_pwrkey_direction_input(struct udevice *dev, unsigned int offset)
-{
- return 0;
-}
-
-static int qcom_pwrkey_direction_output(struct udevice *dev, unsigned int offset, int value)
-{
- return -EOPNOTSUPP;
-}
-
-static const struct dm_gpio_ops qcom_pwrkey_ops = {
- .get_value = qcom_pwrkey_get_value,
- .get_function = qcom_pwrkey_get_function,
- .direction_input = qcom_pwrkey_direction_input,
- .direction_output = qcom_pwrkey_direction_output,
-};
-
-static int qcom_pwrkey_probe(struct udevice *dev)
-{
- struct qcom_gpio_bank *priv = dev_get_priv(dev);
- int reg;
- u64 pid;
-
- pid = dev_read_addr(dev);
- if (pid == FDT_ADDR_T_NONE)
- return log_msg_ret("bad address", -EINVAL);
-
- priv->pid = pid;
-
- /* Do a sanity check */
- reg = pmic_reg_read(dev->parent, priv->pid + REG_TYPE);
- if (reg != 0x1)
- return log_msg_ret("bad type", -ENXIO);
-
- reg = pmic_reg_read(dev->parent, priv->pid + REG_SUBTYPE);
- if ((reg & 0x5) == 0)
- return log_msg_ret("bad subtype", -ENXIO);
-
- return 0;
-}
-
-static int qcom_pwrkey_of_to_plat(struct udevice *dev)
-{
- struct gpio_dev_priv *uc_priv = dev_get_uclass_priv(dev);
-
- uc_priv->gpio_count = 2;
- uc_priv->bank_name = dev_read_string(dev, "gpio-bank-name");
- if (uc_priv->bank_name == NULL)
- uc_priv->bank_name = "pwkey_qcom";
-
- return 0;
-}
-
-static const struct udevice_id qcom_pwrkey_ids[] = {
- { .compatible = "qcom,pm8916-pwrkey" },
- { .compatible = "qcom,pm8994-pwrkey" },
- { .compatible = "qcom,pm8998-pwrkey" },
- { }
-};
-
-U_BOOT_DRIVER(pwrkey_qcom) = {
- .name = "pwrkey_qcom",
- .id = UCLASS_GPIO,
- .of_match = qcom_pwrkey_ids,
- .of_to_plat = qcom_pwrkey_of_to_plat,
- .probe = qcom_pwrkey_probe,
- .ops = &qcom_pwrkey_ops,
- .priv_auto = sizeof(struct qcom_gpio_bank),
-};
--
2.42.0
More information about the U-Boot
mailing list