[PATCH v1 1/2] sunxi: SPL SPI: Add SPI boot support for the Allwinner R528/T113 SoCs
Maksim Kiselev
bigunclemax at gmail.com
Sat Nov 11 14:33:07 CET 2023
R528/T113 SoCs uses the same SPI IP as the H6, also have the same clocks
and reset bits layout, but the CCU base is different. Another difference
is that the new SoCs do not have a clock divider inside. Instead of this
we should configure sample mode depending on input clock rate.
The pin assignment is also different: the H6 uses PC0, the R528/T113 PC4
instead. This makes for a change in spi0_pinmux_setup() routine.
This patch extends the H6/H616 #ifdef guards to also cover the R528/T113,
using the shared CONFIG_SUNXI_GEN_NCAT2 and CONFIG_MACH_SUN8I_R528
symbols. Also use CONFIG_SUNXI_GEN_NCAT2 symbol for the Kconfig
dependency.
Signed-off-by: Maksim Kiselev <bigunclemax at gmail.com>
Tested-by: Sam Edwards <CFSworks at gmail.com>
---
arch/arm/mach-sunxi/Kconfig | 2 +-
arch/arm/mach-sunxi/spl_spi_sunxi.c | 78 +++++++++++++++++++++--------
2 files changed, 58 insertions(+), 22 deletions(-)
diff --git a/arch/arm/mach-sunxi/Kconfig b/arch/arm/mach-sunxi/Kconfig
index a10e4c06b6..732f60821a 100644
--- a/arch/arm/mach-sunxi/Kconfig
+++ b/arch/arm/mach-sunxi/Kconfig
@@ -1044,7 +1044,7 @@ config SPL_STACK_R_ADDR
config SPL_SPI_SUNXI
bool "Support for SPI Flash on Allwinner SoCs in SPL"
- depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || SUN50I_GEN_H6 || MACH_SUNIV
+ depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUNXI_H3_H5 || MACH_SUN50I || MACH_SUN8I_R40 || SUN50I_GEN_H6 || MACH_SUNIV || SUNXI_GEN_NCAT2
help
Enable support for SPI Flash. This option allows SPL to read from
sunxi SPI Flash. It uses the same method as the boot ROM, so does
diff --git a/arch/arm/mach-sunxi/spl_spi_sunxi.c b/arch/arm/mach-sunxi/spl_spi_sunxi.c
index c2410dd7bb..ba3b1579f0 100644
--- a/arch/arm/mach-sunxi/spl_spi_sunxi.c
+++ b/arch/arm/mach-sunxi/spl_spi_sunxi.c
@@ -73,18 +73,27 @@
#define SUN6I_CTL_ENABLE BIT(0)
#define SUN6I_CTL_MASTER BIT(1)
#define SUN6I_CTL_SRST BIT(31)
+#define SUN6I_TCR_SDM BIT(13)
#define SUN6I_TCR_XCH BIT(31)
/*****************************************************************************/
-#define CCM_AHB_GATING0 (0x01C20000 + 0x60)
-#define CCM_H6_SPI_BGR_REG (0x03001000 + 0x96c)
-#ifdef CONFIG_SUN50I_GEN_H6
-#define CCM_SPI0_CLK (0x03001000 + 0x940)
+#if IS_ENABLED(CONFIG_SUN50I_GEN_H6)
+#define CCM_BASE 0x03001000
+#elif IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2)
+#define CCM_BASE 0x02001000
#else
-#define CCM_SPI0_CLK (0x01C20000 + 0xA0)
+#define CCM_BASE 0x01C20000
#endif
-#define SUN6I_BUS_SOFT_RST_REG0 (0x01C20000 + 0x2C0)
+
+#define CCM_AHB_GATING0 (CCM_BASE + 0x60)
+#define CCM_H6_SPI_BGR_REG (CCM_BASE + 0x96c)
+#if IS_ENABLED(CONFIG_SUN50I_GEN_H6) || IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2)
+#define CCM_SPI0_CLK (CCM_BASE + 0x940)
+#else
+#define CCM_SPI0_CLK (CCM_BASE + 0xA0)
+#endif
+#define SUN6I_BUS_SOFT_RST_REG0 (CCM_BASE + 0x2C0)
#define AHB_RESET_SPI0_SHIFT 20
#define AHB_GATE_OFFSET_SPI0 20
@@ -102,17 +111,22 @@
*/
static void spi0_pinmux_setup(unsigned int pin_function)
{
- /* All chips use PC0 and PC2. */
- sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
+ /* All chips use PC2. And all chips use PC0, except R528/T113 */
+ if (!IS_ENABLED(CONFIG_MACH_SUN8I_R528))
+ sunxi_gpio_set_cfgpin(SUNXI_GPC(0), pin_function);
+
sunxi_gpio_set_cfgpin(SUNXI_GPC(2), pin_function);
- /* All chips except H6 and H616 use PC1. */
- if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+ /* All chips except H6/H616/R528/T113 use PC1. */
+ if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
+ !IS_ENABLED(CONFIG_MACH_SUN8I_R528))
sunxi_gpio_set_cfgpin(SUNXI_GPC(1), pin_function);
- if (IS_ENABLED(CONFIG_MACH_SUN50I_H6))
+ if (IS_ENABLED(CONFIG_MACH_SUN50I_H6) ||
+ IS_ENABLED(CONFIG_MACH_SUN8I_R528))
sunxi_gpio_set_cfgpin(SUNXI_GPC(5), pin_function);
- if (IS_ENABLED(CONFIG_MACH_SUN50I_H616))
+ if (IS_ENABLED(CONFIG_MACH_SUN50I_H616) ||
+ IS_ENABLED(CONFIG_MACH_SUN8I_R528))
sunxi_gpio_set_cfgpin(SUNXI_GPC(4), pin_function);
/* Older generations use PC23 for CS, newer ones use PC3. */
@@ -126,7 +140,8 @@ static void spi0_pinmux_setup(unsigned int pin_function)
static bool is_sun6i_gen_spi(void)
{
return IS_ENABLED(CONFIG_SUNXI_GEN_SUN6I) ||
- IS_ENABLED(CONFIG_SUN50I_GEN_H6);
+ IS_ENABLED(CONFIG_SUN50I_GEN_H6) ||
+ IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2);
}
static uintptr_t spi0_base_address(void)
@@ -137,6 +152,9 @@ static uintptr_t spi0_base_address(void)
if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
return 0x05010000;
+ if (IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
+ return 0x04025000;
+
if (!is_sun6i_gen_spi() ||
IS_ENABLED(CONFIG_MACH_SUNIV))
return 0x01C05000;
@@ -152,23 +170,30 @@ static void spi0_enable_clock(void)
uintptr_t base = spi0_base_address();
/* Deassert SPI0 reset on SUN6I */
- if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+ if (IS_ENABLED(CONFIG_SUN50I_GEN_H6) ||
+ IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
setbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
else if (is_sun6i_gen_spi())
setbits_le32(SUN6I_BUS_SOFT_RST_REG0,
(1 << AHB_RESET_SPI0_SHIFT));
/* Open the SPI0 gate */
- if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+ if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
+ !IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
setbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
if (IS_ENABLED(CONFIG_MACH_SUNIV)) {
/* Divide by 32, clock source is AHB clock 200MHz */
writel(SPI0_CLK_DIV_BY_32, base + SUN6I_SPI0_CCTL);
} else {
- /* Divide by 4 */
- writel(SPI0_CLK_DIV_BY_4, base + (is_sun6i_gen_spi() ?
- SUN6I_SPI0_CCTL : SUN4I_SPI0_CCTL));
+ /* New SoCs do not have a clock divider inside */
+ if (!IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2)) {
+ /* Divide by 4 */
+ writel(SPI0_CLK_DIV_BY_4,
+ base + (is_sun6i_gen_spi() ? SUN6I_SPI0_CCTL :
+ SUN4I_SPI0_CCTL));
+ }
+
/* 24MHz from OSC24M */
writel((1 << 31), CCM_SPI0_CLK);
}
@@ -180,6 +205,14 @@ static void spi0_enable_clock(void)
/* Wait for completion */
while (readl(base + SUN6I_SPI0_GCR) & SUN6I_CTL_SRST)
;
+
+ /*
+ * For new SoCs we should configure sample mode depending on
+ * input clock. As 24MHz from OSC24M is used, we could use
+ * normal sample mode by setting SDM bit in the TCR register
+ */
+ if (IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
+ setbits_le32(base + SUN6I_SPI0_TCR, SUN6I_TCR_SDM);
} else {
/* Enable SPI in the master mode and reset FIFO */
setbits_le32(base + SUN4I_SPI0_CTL, SUN4I_CTL_MASTER |
@@ -206,11 +239,13 @@ static void spi0_disable_clock(void)
writel(0, CCM_SPI0_CLK);
/* Close the SPI0 gate */
- if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+ if (!IS_ENABLED(CONFIG_SUN50I_GEN_H6) &&
+ !IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
clrbits_le32(CCM_AHB_GATING0, (1 << AHB_GATE_OFFSET_SPI0));
/* Assert SPI0 reset on SUN6I */
- if (IS_ENABLED(CONFIG_SUN50I_GEN_H6))
+ if (IS_ENABLED(CONFIG_SUN50I_GEN_H6) ||
+ IS_ENABLED(CONFIG_SUNXI_GEN_NCAT2))
clrbits_le32(CCM_H6_SPI_BGR_REG, (1U << 16) | 0x1);
else if (is_sun6i_gen_spi())
clrbits_le32(SUN6I_BUS_SOFT_RST_REG0,
@@ -224,7 +259,8 @@ static void spi0_init(void)
if (IS_ENABLED(CONFIG_MACH_SUN50I) ||
IS_ENABLED(CONFIG_SUN50I_GEN_H6))
pin_function = SUN50I_GPC_SPI0;
- else if (IS_ENABLED(CONFIG_MACH_SUNIV))
+ else if (IS_ENABLED(CONFIG_MACH_SUNIV) ||
+ IS_ENABLED(CONFIG_MACH_SUN8I_R528))
pin_function = SUNIV_GPC_SPI0;
spi0_pinmux_setup(pin_function);
--
2.40.1
More information about the U-Boot
mailing list