[PATCH v4 2/8] arm: mach-k3: common: Reserve video memory from end of the RAM

[Devarsh Thakkar]

Setup video memory before page table reservation using
"spl_reserve_video_from_ram_top" which ensures framebuffer memory gets
reserved from the end of RAM.

This is done to enable the next stage to directly skip the
pre-reserved area from previous stage right from the end of RAM without
having to make any gaps/holes to accommodate those regions which was the
case before as previous stage reserved region not from the end of RAM.

Use gd->ram_top instead of local ram_top and update gd->reloc_addr after
each reservation to ensure further regions are reserved properly.

Signed-off-by: Devarsh Thakkar <devarsht at ti.com>
---
V2:
 - Make a generic function "spl_reserve_video" under
   common/spl which can be re-used by other platforms too
   for reserving video memory from spl.

V3:
 - Change spl_reserve_video to spl_reserve_video_from_ram_top
   which enforce framebuffer reservation from end of RAM
 - Use gd->ram_top instead of local ram_top and update
   gd->reloc_addr after each reservation
 - Print error message on framebuffer reservation

V4:
 - Split this into a separate patch
---
 arch/arm/mach-k3/common.c | 17 ++++++++++++-----
 1 file changed, 12 insertions(+), 5 deletions(-)

diff --git a/arch/arm/mach-k3/common.c b/arch/arm/mach-k3/common.c
index fd400e7e3d..42ceeb5296 100644
--- a/arch/arm/mach-k3/common.c
+++ b/arch/arm/mach-k3/common.c
@@ -524,19 +524,26 @@ void remove_fwl_configs(struct fwl_data *fwl_data, size_t fwl_data_size)
 void spl_enable_cache(void)
 {
 #if !(defined(CONFIG_SYS_ICACHE_OFF) && defined(CONFIG_SYS_DCACHE_OFF))
-	phys_addr_t ram_top = CFG_SYS_SDRAM_BASE;
+	gd->ram_top = CFG_SYS_SDRAM_BASE;
+	int ret = 0;
 
 	dram_init();
 
 	/* reserve TLB table */
 	gd->arch.tlb_size = PGTABLE_SIZE;
 
-	ram_top += get_effective_memsize();
+	gd->ram_top += get_effective_memsize();
 	/* keep ram_top in the 32-bit address space */
-	if (ram_top >= 0x100000000)
-		ram_top = (phys_addr_t) 0x100000000;
+	if (gd->ram_top >= 0x100000000)
+		gd->ram_top = (phys_addr_t)0x100000000;
 
-	gd->arch.tlb_addr = ram_top - gd->arch.tlb_size;
+	gd->relocaddr = gd->ram_top;
+
+	ret = spl_reserve_video_from_ram_top();
+	if (ret)
+		panic("Failed to reserve framebuffer memory (%d)\n", ret);
+
+	gd->arch.tlb_addr = gd->relocaddr - gd->arch.tlb_size;
 	gd->arch.tlb_addr &= ~(0x10000 - 1);
 	debug("TLB table from %08lx to %08lx\n", gd->arch.tlb_addr,
 	      gd->arch.tlb_addr + gd->arch.tlb_size);
-- 
2.34.1