[PATCH v4 5/5] pmic: qcom: dont use dev_read_addr to get USID

[Caleb Connolly]

Linux DTs stuff a value indicating if the USID is a USID or a GSID in the
reg property, the Linux SPMI driver then reads the two address cells
separately. U-boot's dev_read_addr() doesn't know how to handle this, so
use ofnode_read_u32_index() to get just the USID.

The Qcom pmic driver doesn't have support for GSID handling, so just
ignore the second value for now.

Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
 doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt | 94 ------------------------
 drivers/power/pmic/pmic_qcom.c                   | 13 +++-
 2 files changed, 10 insertions(+), 97 deletions(-)

diff --git a/doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt b/doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt
deleted file mode 100644
index eb78e3ae7703..000000000000
--- a/doc/device-tree-bindings/pmic/qcom,spmi-pmic.txt
+++ /dev/null
@@ -1,94 +0,0 @@
-          Qualcomm SPMI PMICs multi-function device bindings
-
-The Qualcomm SPMI series presently includes PM8941, PM8841 and PMA8084
-PMICs.  These PMICs use a QPNP scheme through SPMI interface.
-QPNP is effectively a partitioning scheme for dividing the SPMI extended
-register space up into logical pieces, and set of fixed register
-locations/definitions within these regions, with some of these regions
-specifically used for interrupt handling.
-
-The QPNP PMICs are used with the Qualcomm Snapdragon series SoCs, and are
-interfaced to the chip via the SPMI (System Power Management Interface) bus.
-Support for multiple independent functions are implemented by splitting the
-16-bit SPMI slave address space into 256 smaller fixed-size regions, 256 bytes
-each. A function can consume one or more of these fixed-size register regions.
-
-Required properties:
-- compatible:      Should contain one of:
-                   "qcom,pm660",
-                   "qcom,pm660l",
-                   "qcom,pm7325",
-                   "qcom,pm8004",
-                   "qcom,pm8005",
-                   "qcom,pm8019",
-                   "qcom,pm8028",
-                   "qcom,pm8110",
-                   "qcom,pm8150",
-                   "qcom,pm8150b",
-                   "qcom,pm8150c",
-                   "qcom,pm8150l",
-                   "qcom,pm8226",
-                   "qcom,pm8350c",
-                   "qcom,pm8841",
-                   "qcom,pm8901",
-                   "qcom,pm8909",
-                   "qcom,pm8916",
-                   "qcom,pm8941",
-                   "qcom,pm8950",
-                   "qcom,pm8953",
-                   "qcom,pm8994",
-                   "qcom,pm8998",
-                   "qcom,pma8084",
-                   "qcom,pmd9635",
-                   "qcom,pmi8950",
-                   "qcom,pmi8962",
-                   "qcom,pmi8994",
-                   "qcom,pmi8998",
-                   "qcom,pmk8002",
-                   "qcom,pmk8350",
-                   "qcom,pmr735a",
-                   "qcom,smb2351",
-                   or generalized "qcom,spmi-pmic".
-- reg:             Specifies the SPMI USID slave address for this device.
-                   For more information see:
-                   Documentation/devicetree/bindings/spmi/spmi.yaml
-
-Required properties for peripheral child nodes:
-- compatible:      Should contain "qcom,xxx", where "xxx" is a peripheral name.
-
-Optional properties for peripheral child nodes:
-- interrupts:      Interrupts are specified as a 4-tuple. For more information
-                   see:
-                   Documentation/devicetree/bindings/spmi/qcom,spmi-pmic-arb.yaml
-- interrupt-names: Corresponding interrupt name to the interrupts property
-
-Each child node of SPMI slave id represents a function of the PMIC. In the
-example below the rtc device node represents a peripheral of pm8941
-SID = 0. The regulator device node represents a peripheral of pm8941 SID = 1.
-
-Example:
-
-	spmi {
-		compatible = "qcom,spmi-pmic-arb";
-
-		pm8941 at 0 {
-			compatible = "qcom,pm8941", "qcom,spmi-pmic";
-			reg = <0x0 SPMI_USID>;
-
-			rtc {
-				compatible = "qcom,rtc";
-				interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
-				interrupt-names = "alarm";
-			};
-		};
-
-		pm8941 at 1 {
-			compatible = "qcom,pm8941", "qcom,spmi-pmic";
-			reg = <0x1 SPMI_USID>;
-
-			regulator {
-				compatible = "qcom,regulator";
-				regulator-name = "8941_boost";
-			};
-		};
-	};
diff --git a/drivers/power/pmic/pmic_qcom.c b/drivers/power/pmic/pmic_qcom.c
index ad8daf43f06f..f2ac6494811d 100644
--- a/drivers/power/pmic/pmic_qcom.c
+++ b/drivers/power/pmic/pmic_qcom.c
@@ -66,12 +66,19 @@ static const struct udevice_id pmic_qcom_ids[] = {
 static int pmic_qcom_probe(struct udevice *dev)
 {
 	struct pmic_qcom_priv *priv = dev_get_priv(dev);
+	int ret;
 
-	priv->usid = dev_read_addr(dev);
-
-	if (priv->usid == FDT_ADDR_T_NONE)
+	/*
+	 * dev_read_addr() can't be used here because the reg property actually
+	 * contains two discrete values, not a single 64-bit address.
+	 * The address is the first value.
+	 */
+	ret = ofnode_read_u32_index(dev_ofnode(dev), "reg", 0, &priv->usid);
+	if (ret < 0)
 		return -EINVAL;
 
+	debug("usid: %d\n", priv->usid);
+
 	return 0;
 }
 

-- 
2.42.1