[PATCH 2/2] board: ti: am64x: Switch to standard boot flow
Nishanth Menon
nm at ti.com
Wed Oct 4 15:59:00 CEST 2023
On 16:23-20231004, Roger Quadros wrote:
> Switch to using bootstd. Note with this change, we will stop using
> distro_bootcmd and instead depend entirely on bootflow method of
> starting the system up.
>
> Signed-off-by: Roger Quadros <rogerq at kernel.org>
> ---
> board/ti/am64x/am64x.env | 1 +
> configs/am64x_evm_a53_defconfig | 5 +++--
> include/configs/am64x_evm.h | 2 --
> 3 files changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/board/ti/am64x/am64x.env b/board/ti/am64x/am64x.env
> index 68e42222b7..efd736b99b 100644
> --- a/board/ti/am64x/am64x.env
> +++ b/board/ti/am64x/am64x.env
> @@ -15,6 +15,7 @@ console=ttyS2,115200n8
> args_all=setenv optargs earlycon=ns16550a,mmio32,0x02800000 ${mtdparts}
> run_kern=booti ${loadaddr} ${rd_spec} ${fdtaddr}
>
> +boot_targets=mmc1 mmc0 usb pxe dhcp
> boot=mmc
> mmcdev=1
> bootpart=1:2
> diff --git a/configs/am64x_evm_a53_defconfig b/configs/am64x_evm_a53_defconfig
> index 718ad176cb..43bfcf957a 100644
> --- a/configs/am64x_evm_a53_defconfig
> +++ b/configs/am64x_evm_a53_defconfig
> @@ -31,8 +31,9 @@ CONFIG_SPL_SPI=y
> # CONFIG_SYS_MALLOC_CLEAR_ON_INIT is not set
> CONFIG_SPL_LOAD_FIT=y
> CONFIG_SPL_LOAD_FIT_ADDRESS=0x81000000
> -CONFIG_DISTRO_DEFAULTS=y
> -CONFIG_BOOTCOMMAND="run envboot; run distro_bootcmd;"
> +CONFIG_BOOTSTD_FULL=y
> +CONFIG_BOOTSTD_DEFAULTS=y
> +CONFIG_BOOTCOMMAND="run envboot; bootflow scan -lb"
> CONFIG_BOARD_LATE_INIT=y
> CONFIG_SPL_MAX_SIZE=0x180000
> CONFIG_SPL_HAS_BSS_LINKER_SECTION=y
> diff --git a/include/configs/am64x_evm.h b/include/configs/am64x_evm.h
> index 062102a610..d3d9eac8b6 100644
> --- a/include/configs/am64x_evm.h
> +++ b/include/configs/am64x_evm.h
> @@ -10,8 +10,6 @@
> #define __CONFIG_AM642_EVM_H
>
> #include <linux/sizes.h>
Do we really need this?
> -#include <config_distro_bootcmd.h>
> -#include <env/ti/mmc.h>
> #include <asm/arch/am64_hardware.h>
OR this?
> #include <env/ti/k3_dfu.h>
you dont need k3_dfu.h either. the env setup is already in
board/ti/am64x/am64x.env (k3_dfu.env)
and we dont seem to be using CFG_SYS_SDRAM_BASE1
might be that we could reduce it down to am62x_evm.h ?
>
> --
> 2.34.1
>
--
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3 1A34 DDB5 849D 1736 249D
More information about the U-Boot
mailing list