[PATCH 1/5] arm64: zynqmp: Use mdio node by vp-x-a2785-00-revA and vpk120-revA

[Michal Simek]

All boards have been converted to use mdio node that's why move ethernet
phys under mdio node too.

Signed-off-by: Michal Simek <michal.simek at amd.com>
---

Same change was done by:
https://lore.kernel.org/r/ff165281a70a38e2b76fee91e6255ce95ce8021b.1695378830.git.michal.simek@amd.com
---
 arch/arm/dts/zynqmp-vp-x-a2785-00-revA.dts | 10 +++++++---
 arch/arm/dts/zynqmp-vpk120-revA.dts        | 10 +++++++---
 2 files changed, 14 insertions(+), 6 deletions(-)

diff --git a/arch/arm/dts/zynqmp-vp-x-a2785-00-revA.dts b/arch/arm/dts/zynqmp-vp-x-a2785-00-revA.dts
index 2f88aa4a0d28..9ab8f5bfffe4 100644
--- a/arch/arm/dts/zynqmp-vp-x-a2785-00-revA.dts
+++ b/arch/arm/dts/zynqmp-vp-x-a2785-00-revA.dts
@@ -119,9 +119,13 @@
 	phy-mode = "sgmii"; /* DTG generates this properly 1512 */
 	is-internal-pcspma;
 	/* phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>; */
-	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
-	phy0: ethernet-phy at 0 { /* u131 - M88e1512 */
-		reg = <0>;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+		phy0: ethernet-phy at 0 { /* u131 - M88e1512 */
+			reg = <0>;
+		};
 	};
 };
 
diff --git a/arch/arm/dts/zynqmp-vpk120-revA.dts b/arch/arm/dts/zynqmp-vpk120-revA.dts
index 66919f578e02..ce76e0b3db36 100644
--- a/arch/arm/dts/zynqmp-vpk120-revA.dts
+++ b/arch/arm/dts/zynqmp-vpk120-revA.dts
@@ -120,9 +120,13 @@
 	phy-mode = "sgmii"; /* DTG generates this properly 1512 */
 	is-internal-pcspma;
 	/* phys = <&psgtr 0 PHY_TYPE_SGMII 0 0>; */
-	/* phy-reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
-	phy0: ethernet-phy at 0 {
-		reg = <0>;
+	mdio: mdio {
+		#address-cells = <1>;
+		#size-cells = <0>;
+		/* reset-gpios = <&gpio 142 GPIO_ACTIVE_LOW>; */
+		phy0: ethernet-phy at 0 {
+			reg = <0>;
+		};
 	};
 };
 
-- 
2.36.1