[PATCH v1] spi: dw: add check for Rx FIFO overflow
Maksim Kiselev
bigunclemax at gmail.com
Tue Oct 17 09:05:06 CEST 2023
If even one byte is lost due to Rx FIFO overflow then we will never
exit the read loop. Because the (priv->rx != priv->rx_end) condition will
be always true.
Let's check if Rx FIFO overflow occurred and exit the read loop
in this case.
Signed-off-by: Maksim Kiselev <bigunclemax at gmail.com>
---
drivers/spi/designware_spi.c | 24 +++++++++++++++++++++---
1 file changed, 21 insertions(+), 3 deletions(-)
diff --git a/drivers/spi/designware_spi.c b/drivers/spi/designware_spi.c
index 1c7d0ca310..0f443bff8e 100644
--- a/drivers/spi/designware_spi.c
+++ b/drivers/spi/designware_spi.c
@@ -111,6 +111,15 @@
#define SR_TX_ERR BIT(5)
#define SR_DCOL BIT(6)
+/* Bit fields in ISR, IMR, RISR, 7 bits */
+#define DW_SPI_INT_MASK GENMASK(5, 0)
+#define DW_SPI_INT_TXEI BIT(0)
+#define DW_SPI_INT_TXOI BIT(1)
+#define DW_SPI_INT_RXUI BIT(2)
+#define DW_SPI_INT_RXOI BIT(3)
+#define DW_SPI_INT_RXFI BIT(4)
+#define DW_SPI_INT_MSTI BIT(5)
+
#define RX_TIMEOUT 1000 /* timeout in ms */
struct dw_spi_plat {
@@ -588,7 +597,7 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
struct dw_spi_priv *priv = dev_get_priv(bus);
u8 op_len = op->cmd.nbytes + op->addr.nbytes + op->dummy.nbytes;
u8 op_buf[op_len];
- u32 cr0;
+ u32 cr0, sts;
if (read)
priv->tmode = CTRLR0_TMOD_EPROMREAD;
@@ -632,12 +641,21 @@ static int dw_spi_exec_op(struct spi_slave *slave, const struct spi_mem_op *op)
* them to fail because we are not reading/writing the fifo fast enough.
*/
if (read) {
- priv->rx = op->data.buf.in;
+ void *prev_rx = priv->rx = op->data.buf.in;
priv->rx_end = priv->rx + op->data.nbytes;
dw_write(priv, DW_SPI_SER, 1 << spi_chip_select(slave->dev));
- while (priv->rx != priv->rx_end)
+ while (priv->rx != priv->rx_end) {
dw_reader(priv);
+ if (prev_rx == priv->rx) {
+ sts = dw_read(priv, DW_SPI_RISR);
+ if (sts & DW_SPI_INT_RXOI) {
+ dev_err(bus, "FIFO overflow on Rx\n");
+ return -EIO;
+ }
+ }
+ prev_rx = priv->rx;
+ }
} else {
u32 val;
--
2.40.1
More information about the U-Boot
mailing list