[PATCH v2 7/7] clk/qcom: fix rcg divider value
Caleb Connolly
caleb.connolly at linaro.org
Mon Oct 30 23:23:29 CET 2023
The RCG divider field takes a value of (2*h - 1) where h is the divisor.
This allows fractional dividers to be supported by calculating them at
compile time using a macro.
However, the clk_rcg_set_rate_mnd() function was also performing the
calculation. Clean this all up and consistently use the F() macro to
calculate these at compile time and properly support fractional divisors.
Additionally, improve clk_bcr_update() to timeout with a warning rather
than hanging the board, and make the freq_tbl struct and helpers common
so that they can be reused by future platforms.
Signed-off-by: Caleb Connolly <caleb.connolly at linaro.org>
---
drivers/clk/qcom/clock-apq8016.c | 2 +-
drivers/clk/qcom/clock-apq8096.c | 2 +-
drivers/clk/qcom/clock-qcom.c | 66 +++++++++++++++++++++++++++++-----------
drivers/clk/qcom/clock-qcom.h | 11 +++++++
drivers/clk/qcom/clock-qcs404.c | 16 +++++-----
drivers/clk/qcom/clock-sdm845.c | 26 ----------------
6 files changed, 69 insertions(+), 54 deletions(-)
diff --git a/drivers/clk/qcom/clock-apq8016.c b/drivers/clk/qcom/clock-apq8016.c
index 630619c83454..eb812934cbae 100644
--- a/drivers/clk/qcom/clock-apq8016.c
+++ b/drivers/clk/qcom/clock-apq8016.c
@@ -78,7 +78,7 @@ static struct vote_clk gcc_blsp1_ahb_clk = {
/* SDHCI */
static int clk_init_sdc(struct msm_clk_priv *priv, int slot, uint rate)
{
- int div = 8; /* 100MHz default */
+ int div = 15; /* 100MHz default */
if (rate == 200000000)
div = 4;
diff --git a/drivers/clk/qcom/clock-apq8096.c b/drivers/clk/qcom/clock-apq8096.c
index 095c1b431245..55f16c14e046 100644
--- a/drivers/clk/qcom/clock-apq8096.c
+++ b/drivers/clk/qcom/clock-apq8096.c
@@ -65,7 +65,7 @@ static struct vote_clk gcc_blsp2_ahb_clk = {
static int clk_init_sdc(struct msm_clk_priv *priv, uint rate)
{
- int div = 3;
+ int div = 5;
clk_enable_cbc(priv->base + SDCC2_AHB_CBCR);
clk_rcg_set_rate_mnd(priv->base, &sdc_regs, div, 0, 0,
diff --git a/drivers/clk/qcom/clock-qcom.c b/drivers/clk/qcom/clock-qcom.c
index fc478554f982..58374d356942 100644
--- a/drivers/clk/qcom/clock-qcom.c
+++ b/drivers/clk/qcom/clock-qcom.c
@@ -12,6 +12,8 @@
* Based on Little Kernel driver, simplified
*/
+#define LOG_DEBUG
+
#include <common.h>
#include <clk-uclass.h>
#include <dm.h>
@@ -19,6 +21,8 @@
#include <dm/lists.h>
#include <errno.h>
#include <asm/io.h>
+#include <linux/bug.h>
+#include <linux/delay.h>
#include <linux/bitops.h>
#include <reset-uclass.h>
@@ -68,30 +72,42 @@ void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk)
/* Update clock command via CMD_RCGR */
void clk_bcr_update(phys_addr_t apps_cmd_rcgr)
{
+ u32 count;
setbits_le32(apps_cmd_rcgr, APPS_CMD_RCGR_UPDATE);
/* Wait for frequency to be updated. */
- while (readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE)
- ;
+ for (count = 0; count < 50000; count++) {
+ if (!(readl(apps_cmd_rcgr) & APPS_CMD_RCGR_UPDATE))
+ break;
+ udelay(1);
+ }
+ WARN(count == 50000, "WARNING: RCG @ %#llx [%#010x] stuck at off\n",
+ apps_cmd_rcgr, readl(apps_cmd_rcgr));
}
-#define CFG_MODE_DUAL_EDGE (0x2 << 12) /* Counter mode */
+#define CFG_SRC_DIV_MASK 0b11111
+#define CFG_SRC_SEL_SHIFT 8
+#define CFG_SRC_SEL_MASK (0x7 << CFG_SRC_SEL_SHIFT)
+#define CFG_MODE_SHIFT 12
+#define CFG_MODE_MASK (0x3 << CFG_MODE_SHIFT)
+#define CFG_MODE_DUAL_EDGE (0x2 << CFG_MODE_SHIFT)
+#define CFG_HW_CLK_CTRL_MASK BIT(20)
-#define CFG_MASK 0x3FFF
-
-#define CFG_DIVIDER_MASK 0x1F
-
-/* root set rate for clocks with half integer and MND divider */
+/*
+ * root set rate for clocks with half integer and MND divider
+ * div should be pre-calculated ((div * 2) - 1)
+ */
void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
int div, int m, int n, int source, u8 mnd_width)
{
u32 cfg;
/* M value for MND divider. */
u32 m_val = m;
+ u32 n_minus_m = n - m;
/* NOT(N-M) value for MND divider. */
- u32 n_val = ~((n) - (m)) * !!(n);
+ u32 n_val = ~n_minus_m * !!(n);
/* NOT 2D value for MND divider. */
- u32 d_val = ~(n);
+ u32 d_val = ~(clamp_t(u32, n, m, n_minus_m));
u32 mask = BIT(mnd_width) - 1;
debug("m %#x n %#x d %#x div %#x mask %#x\n", m_val, n_val, d_val, div, mask);
@@ -103,15 +119,13 @@ void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
/* setup src select and divider */
cfg = readl(base + regs->cfg_rcgr);
- cfg &= ~CFG_MASK;
- cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */
+ cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK);
+ cfg |= source & CFG_SRC_SEL_MASK; /* Select clock source */
- /* Set the divider; HW permits fraction dividers (+0.5), but
- for simplicity, we will support integers only */
if (div)
- cfg |= (2 * div - 1) & CFG_DIVIDER_MASK;
+ cfg |= div & CFG_SRC_DIV_MASK;
- if (n_val)
+ if (n && (n != m))
cfg |= CFG_MODE_DUAL_EDGE;
writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */
@@ -128,7 +142,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
/* setup src select and divider */
cfg = readl(base + regs->cfg_rcgr);
- cfg &= ~CFG_MASK;
+ cfg &= ~(CFG_SRC_SEL_MASK | CFG_MODE_MASK | CFG_HW_CLK_CTRL_MASK);
cfg |= source & CFG_CLK_SRC_MASK; /* Select clock source */
/*
@@ -136,7 +150,7 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
* for simplicity, we will support integers only
*/
if (div)
- cfg |= (2 * div - 1) & CFG_DIVIDER_MASK;
+ cfg |= (2 * div - 1) & CFG_SRC_DIV_MASK;
writel(cfg, base + regs->cfg_rcgr); /* Write new clock configuration */
@@ -144,6 +158,22 @@ void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
clk_bcr_update(base + regs->cmd_rcgr);
}
+const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate)
+{
+ if (!f)
+ return NULL;
+
+ if (!f->freq)
+ return f;
+
+ for (; f->freq; f++)
+ if (rate <= f->freq)
+ return f;
+
+ /* Default to our fastest rate */
+ return f - 1;
+}
+
static int msm_clk_probe(struct udevice *dev)
{
struct msm_clk_data *data = (struct msm_clk_data *)dev_get_driver_data(dev);
diff --git a/drivers/clk/qcom/clock-qcom.h b/drivers/clk/qcom/clock-qcom.h
index 24a32cb9666d..01088c19015a 100644
--- a/drivers/clk/qcom/clock-qcom.h
+++ b/drivers/clk/qcom/clock-qcom.h
@@ -32,6 +32,16 @@ struct bcr_regs {
uintptr_t D;
};
+struct freq_tbl {
+ uint freq;
+ uint src;
+ u8 pre_div;
+ u16 m;
+ u16 n;
+};
+
+#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) }
+
struct gate_clk {
uintptr_t reg;
u32 en_val;
@@ -71,6 +81,7 @@ void clk_enable_gpll0(phys_addr_t base, const struct pll_vote_clk *gpll0);
void clk_bcr_update(phys_addr_t apps_cmd_rgcr);
void clk_enable_cbc(phys_addr_t cbcr);
void clk_enable_vote_clk(phys_addr_t base, const struct vote_clk *vclk);
+const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate);
void clk_rcg_set_rate_mnd(phys_addr_t base, const struct bcr_regs *regs,
int div, int m, int n, int source, u8 mnd_width);
void clk_rcg_set_rate(phys_addr_t base, const struct bcr_regs *regs, int div,
diff --git a/drivers/clk/qcom/clock-qcs404.c b/drivers/clk/qcom/clock-qcs404.c
index 921abf1f699b..429ff35e1d1a 100644
--- a/drivers/clk/qcom/clock-qcs404.c
+++ b/drivers/clk/qcom/clock-qcs404.c
@@ -203,7 +203,7 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
break;
case GCC_SDCC1_APPS_CLK:
/* SDCC1: 200MHz */
- clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 4, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &sdc_regs, 7, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
clk_enable_gpll0(priv->base, &gpll0_vote_clk);
clk_enable_cbc(priv->base + SDCC_APPS_CBCR(1));
@@ -213,16 +213,16 @@ static ulong qcs404_clk_set_rate(struct clk *clk, ulong rate)
break;
case GCC_ETH_RGMII_CLK:
if (rate == 250000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 125000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 4, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &emac_regs, 7, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 50000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 10, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &emac_regs, 19, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
else if (rate == 5000000)
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 1, 50,
+ clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 1, 50,
CFG_CLK_SRC_GPLL1, 8);
break;
default:
@@ -239,7 +239,7 @@ static int qcs404_clk_enable(struct clk *clk)
switch (clk->id) {
case GCC_USB30_MASTER_CLK:
clk_enable_cbc(priv->base + USB30_MASTER_CBCR);
- clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 4, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &usb30_master_regs, 7, 0, 0,
CFG_CLK_SRC_GPLL0, 8);
break;
case GCC_SYS_NOC_USB3_CLK:
@@ -261,14 +261,14 @@ static int qcs404_clk_enable(struct clk *clk)
/* SPEED_1000: freq -> 250MHz */
clk_enable_cbc(priv->base + ETH_PTP_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
- clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 2, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &emac_ptp_regs, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_RGMII_CLK:
/* SPEED_1000: freq -> 250MHz */
clk_enable_cbc(priv->base + ETH_RGMII_CBCR);
clk_enable_gpll0(priv->base, &gpll1_vote_clk);
- clk_rcg_set_rate_mnd(priv->base, &emac_regs, 2, 0, 0,
+ clk_rcg_set_rate_mnd(priv->base, &emac_regs, 3, 0, 0,
CFG_CLK_SRC_GPLL1, 8);
break;
case GCC_ETH_SLAVE_AHB_CLK:
diff --git a/drivers/clk/qcom/clock-sdm845.c b/drivers/clk/qcom/clock-sdm845.c
index 9e78da482c65..07e3605cdbaf 100644
--- a/drivers/clk/qcom/clock-sdm845.c
+++ b/drivers/clk/qcom/clock-sdm845.c
@@ -30,16 +30,6 @@
#define USB30_SEC_GDSCR 0x10004
#define USB30_PRIM_GDSCR 0xf004
-#define F(f, s, h, m, n) { (f), (s), (2 * (h) - 1), (m), (n) }
-
-struct freq_tbl {
- uint freq;
- uint src;
- u8 pre_div;
- u16 m;
- u16 n;
-};
-
static const struct freq_tbl ftbl_gcc_qupv3_wrap0_s0_clk_src[] = {
F(7372800, CFG_CLK_SRC_GPLL0_EVEN, 1, 384, 15625),
F(14745600, CFG_CLK_SRC_GPLL0_EVEN, 1, 768, 15625),
@@ -67,22 +57,6 @@ static const struct bcr_regs uart2_regs = {
.D = SE9_UART_APPS_D,
};
-const struct freq_tbl *qcom_find_freq(const struct freq_tbl *f, uint rate)
-{
- if (!f)
- return NULL;
-
- if (!f->freq)
- return f;
-
- for (; f->freq; f++)
- if (rate <= f->freq)
- return f;
-
- /* Default to our fastest rate */
- return f - 1;
-}
-
static ulong sdm845_clk_set_rate(struct clk *clk, ulong rate)
{
struct msm_clk_priv *priv = dev_get_priv(clk->dev);
--
2.42.0
More information about the U-Boot
mailing list