[PATCH v3 6/6] board: add support for Schneider HMIBSC board
Sumit Garg
sumit.garg at linaro.org
Fri Apr 5 11:07:42 CEST 2024
Support for Schneider Electric HMIBSC. Features:
- Qualcomm Snapdragon 410C SoC - APQ8016 (4xCortex A53, Adreno 306)
- 2GiB RAM
- 64GiB eMMC, SD slot
- WiFi and Bluetooth
- 2x Host, 1x Device USB port
- HDMI
- Discrete TPM2 chip over SPI
Features enabled in U-Boot:
- RAUC updates
- Environment protection
- USB based ethernet adaptors
Signed-off-by: Sumit Garg <sumit.garg at linaro.org>
---
arch/arm/dts/apq8016-schneider-hmibsc.dts | 491 ++++++++++++++++++++++
board/schneider/hmibsc/MAINTAINERS | 6 +
configs/hmibsc_defconfig | 86 ++++
doc/board/index.rst | 1 +
doc/board/schneider/hmibsc.rst | 45 ++
doc/board/schneider/index.rst | 9 +
include/configs/hmibsc.h | 57 +++
7 files changed, 695 insertions(+)
create mode 100644 arch/arm/dts/apq8016-schneider-hmibsc.dts
create mode 100644 board/schneider/hmibsc/MAINTAINERS
create mode 100644 configs/hmibsc_defconfig
create mode 100644 doc/board/schneider/hmibsc.rst
create mode 100644 doc/board/schneider/index.rst
create mode 100644 include/configs/hmibsc.h
diff --git a/arch/arm/dts/apq8016-schneider-hmibsc.dts b/arch/arm/dts/apq8016-schneider-hmibsc.dts
new file mode 100644
index 00000000000..75c6137e5a1
--- /dev/null
+++ b/arch/arm/dts/apq8016-schneider-hmibsc.dts
@@ -0,0 +1,491 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2015, The Linux Foundation. All rights reserved.
+ * Copyright (c) 2024, Linaro Ltd.
+ */
+
+/dts-v1/;
+
+#include "msm8916-pm8916.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/pinctrl/qcom,pmic-mpp.h>
+#include <dt-bindings/sound/apq8016-lpass.h>
+
+/ {
+ model = "Schneider Electric HMIBSC Board";
+ compatible = "schneider,apq8016-hmibsc", "qcom,apq8016";
+
+ aliases {
+ i2c1 = &blsp_i2c6;
+ i2c3 = &blsp_i2c4;
+ i2c4 = &blsp_i2c3;
+ mmc0 = &sdhc_1; /* eMMC */
+ mmc1 = &sdhc_2; /* SD card */
+ serial0 = &blsp_uart1;
+ serial1 = &blsp_uart2;
+ spi0 = &blsp_spi5;
+ usid0 = &pm8916_0;
+ };
+
+ chosen {
+ stdout-path = "serial0";
+ };
+
+ hdmi-out {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con: endpoint {
+ remote-endpoint = <&adv7533_out>;
+ };
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys";
+ autorepeat;
+ pinctrl-0 = <&msm_key_volp_n_default>;
+ pinctrl-names = "default";
+
+ button {
+ label = "Volume Up";
+ linux,code = <KEY_VOLUMEUP>;
+ gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&pm8916_mpps_leds>;
+ pinctrl-names = "default";
+
+ led-1 {
+ function = LED_FUNCTION_WLAN;
+ color = <LED_COLOR_ID_YELLOW>;
+ gpios = <&pm8916_mpps 2 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "phy0tx";
+ default-state = "off";
+ };
+
+ led-2 {
+ function = LED_FUNCTION_BLUETOOTH;
+ color = <LED_COLOR_ID_BLUE>;
+ gpios = <&pm8916_mpps 3 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "bluetooth-power";
+ default-state = "off";
+ };
+ };
+
+ memory at 80000000 {
+ reg = <0 0x80000000 0 0x40000000>;
+ };
+
+ reserved-memory {
+ ramoops at bff00000 {
+ compatible = "ramoops";
+ reg = <0x0 0xbff00000 0x0 0x100000>;
+ record-size = <0x20000>;
+ console-size = <0x20000>;
+ ftrace-size = <0x20000>;
+ ecc-size = <16>;
+ };
+ };
+
+ usb-hub {
+ compatible = "smsc,usb3503";
+ reset-gpios = <&pm8916_gpios 1 GPIO_ACTIVE_LOW>;
+ initial-mode = <1>;
+ };
+
+ usb_id: usb-id {
+ compatible = "linux,extcon-usb-gpio";
+ id-gpios = <&tlmm 110 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&usb_id_default>;
+ pinctrl-names = "default";
+ };
+};
+
+&blsp_i2c3 {
+ status = "okay";
+
+ eeprom at 50 {
+ compatible = "atmel,24c32";
+ reg = <0x50>;
+ };
+};
+
+&blsp_i2c4 {
+ status = "okay";
+
+ adv_bridge: bridge at 39 {
+ compatible = "adi,adv7533";
+ reg = <0x39>;
+ interrupts-extended = <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
+
+ adi,dsi-lanes = <4>;
+ clocks = <&rpmcc RPM_SMD_BB_CLK2>;
+ clock-names = "cec";
+ pd-gpios = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+
+ avdd-supply = <&pm8916_l6>;
+ a2vdd-supply = <&pm8916_l6>;
+ dvdd-supply = <&pm8916_l6>;
+ pvdd-supply = <&pm8916_l6>;
+ v1p2-supply = <&pm8916_l6>;
+ v3p3-supply = <&pm8916_l17>;
+
+ pinctrl-0 = <&adv7533_int_active &adv7533_switch_active>;
+ pinctrl-1 = <&adv7533_int_suspend &adv7533_switch_suspend>;
+ pinctrl-names = "default","sleep";
+ #sound-dai-cells = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7533_in: endpoint {
+ remote-endpoint = <&mdss_dsi0_out>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7533_out: endpoint {
+ remote-endpoint = <&hdmi_con>;
+ };
+ };
+ };
+ };
+};
+
+&blsp_i2c6 {
+ status = "okay";
+
+ rtc at 30 {
+ compatible = "sii,s35390a";
+ reg = <0x30>;
+ };
+
+ eeprom at 50 {
+ compatible = "atmel,24c256";
+ reg = <0x50>;
+ };
+};
+
+&blsp_spi5 {
+ cs-gpios = <&tlmm 18 GPIO_ACTIVE_LOW>;
+ status = "okay";
+
+ tpm at 0 {
+ compatible = "infineon,slb9670", "tcg,tpm_tis-spi";
+ reg = <0>;
+ spi-max-frequency = <500000>;
+ };
+};
+
+&blsp_uart1 {
+ label = "UART0";
+ status = "okay";
+};
+
+&blsp_uart2 {
+ label = "UART1";
+ status = "okay";
+};
+
+&lpass {
+ status = "okay";
+};
+
+&mdss {
+ status = "okay";
+};
+
+&mdss_dsi0_out {
+ data-lanes = <0 1 2 3>;
+ remote-endpoint = <&adv7533_in>;
+};
+
+&pm8916_codec {
+ qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
+ qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
+ status = "okay";
+};
+
+&pm8916_gpios {
+ gpio-line-names =
+ "USB_HUB_RESET_N_PM",
+ "USB_SW_SEL_PM",
+ "NC",
+ "NC";
+
+ usb_hub_reset_pm: usb-hub-reset-pm-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-high;
+ };
+
+ usb_hub_reset_pm_device: usb-hub-reset-pm-device-state {
+ pins = "gpio1";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ input-disable;
+ output-low;
+ };
+
+ usb_sw_sel_pm: usb-sw-sel-pm-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-high;
+ };
+
+ usb_sw_sel_pm_device: usb-sw-sel-pm-device-state {
+ pins = "gpio2";
+ function = PMIC_GPIO_FUNC_NORMAL;
+ power-source = <PM8916_GPIO_VPH>;
+ input-disable;
+ output-low;
+ };
+};
+
+&pm8916_mpps {
+ gpio-line-names =
+ "NC",
+ "WLAN_LED_CTRL",
+ "BT_LED_CTRL",
+ "NC";
+
+ pm8916_mpps_leds: pm8916-mpps-state {
+ pins = "mpp2", "mpp3";
+ function = "digital";
+ output-low;
+ };
+};
+
+&pm8916_resin {
+ linux,code = <KEY_POWER>;
+ status = "okay";
+};
+
+&pm8916_rpm_regulators {
+ pm8916_l17: l17 {
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+};
+
+&sdhc_1 {
+ status = "okay";
+};
+
+&sdhc_2 {
+ pinctrl-0 = <&sdc2_default &sdc2_cd_default>;
+ pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>;
+ pinctrl-names = "default", "sleep";
+ cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+ status = "okay";
+};
+
+&sound {
+ pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>;
+ pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>;
+ pinctrl-names = "default", "sleep";
+ model = "HMIBSC";
+ audio-routing =
+ "AMIC2", "MIC BIAS Internal2",
+ "AMIC3", "MIC BIAS External1";
+ status = "okay";
+
+ quaternary-dai-link {
+ link-name = "ADV7533";
+ cpu {
+ sound-dai = <&lpass MI2S_QUATERNARY>;
+ };
+ codec {
+ sound-dai = <&adv_bridge 0>;
+ };
+ };
+
+ primary-dai-link {
+ link-name = "WCD";
+ cpu {
+ sound-dai = <&lpass MI2S_PRIMARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
+ };
+ };
+
+ tertiary-dai-link {
+ link-name = "WCD-Capture";
+ cpu {
+ sound-dai = <&lpass MI2S_TERTIARY>;
+ };
+ codec {
+ sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
+ };
+ };
+};
+
+&tlmm {
+ pinctrl-0 = <&uart1_mux0_rs232_high &uart1_mux1_rs232_low>;
+ pinctrl-names = "default";
+
+ adv7533_int_active: adv533-int-active-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_int_suspend: adv7533-int-suspend-state {
+ pins = "gpio31";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ adv7533_switch_active: adv7533-switch-active-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ };
+
+ adv7533_switch_suspend: adv7533-switch-suspend-state {
+ pins = "gpio32";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ msm_key_volp_n_default: msm-key-volp-n-default-state {
+ pins = "gpio107";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+
+ sdc2_cd_default: sdc2-cd-default-state {
+ pins = "gpio38";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ /*
+ * UART1 being the debug console supports various modes of
+ * operation (RS-232/485/422) controlled via GPIOs configured
+ * mux as follows:
+ *
+ * gpio100 gpio99 UART mode
+ * 0 0 loopback
+ * 0 1 RS-232
+ * 1 0 RS-485
+ * 1 1 RS-422
+ *
+ * The default mode configured here is RS-232 mode.
+ */
+ uart1_mux0_rs232_high: uart1-mux0-rs232-state {
+ bootph-all;
+ pins = "gpio99";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-high;
+ };
+
+ uart1_mux1_rs232_low: uart1-mux1-rs232-state {
+ bootph-all;
+ pins = "gpio100";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
+ usb_id_default: usb-id-default-state {
+ pins = "gpio110";
+ function = "gpio";
+ drive-strength = <8>;
+ bias-pull-up;
+ };
+};
+
+&usb {
+ extcon = <&usb_id>, <&usb_id>;
+ pinctrl-0 = <&usb_sw_sel_pm &usb_hub_reset_pm>;
+ pinctrl-1 = <&usb_sw_sel_pm_device &usb_hub_reset_pm_device>;
+ pinctrl-names = "default", "device";
+ status = "okay";
+};
+
+&usb_hs_phy {
+ extcon = <&usb_id>;
+};
+
+&wcnss {
+ firmware-name = "qcom/apq8016/wcnss.mbn";
+ status = "okay";
+};
+
+&wcnss_ctrl {
+ firmware-name = "qcom/apq8016/WCNSS_qcom_wlan_nv_sbc.bin";
+};
+
+&wcnss_iris {
+ compatible = "qcom,wcn3620";
+};
+
+&wcnss_mem {
+ status = "okay";
+};
+
+/* PINCTRL - additions to nodes defined in msm8916.dtsi */
+
+/*
+ * 2mA drive strength is not enough when connecting multiple
+ * I2C devices with different pull up resistors.
+ */
+&blsp_i2c4_default {
+ drive-strength = <16>;
+};
+
+&blsp_i2c6_default {
+ drive-strength = <16>;
+};
+
+&blsp_uart1_default {
+ bootph-all;
+};
+
+/* Enable CoreSight */
+&cti0 { status = "okay"; };
+&cti1 { status = "okay"; };
+&cti12 { status = "okay"; };
+&cti13 { status = "okay"; };
+&cti14 { status = "okay"; };
+&cti15 { status = "okay"; };
+&debug0 { status = "okay"; };
+&debug1 { status = "okay"; };
+&debug2 { status = "okay"; };
+&debug3 { status = "okay"; };
+&etf { status = "okay"; };
+&etm0 { status = "okay"; };
+&etm1 { status = "okay"; };
+&etm2 { status = "okay"; };
+&etm3 { status = "okay"; };
+&etr { status = "okay"; };
+&funnel0 { status = "okay"; };
+&funnel1 { status = "okay"; };
+&replicator { status = "okay"; };
+&stm { status = "okay"; };
+&tpiu { status = "okay"; };
diff --git a/board/schneider/hmibsc/MAINTAINERS b/board/schneider/hmibsc/MAINTAINERS
new file mode 100644
index 00000000000..0f31bbda966
--- /dev/null
+++ b/board/schneider/hmibsc/MAINTAINERS
@@ -0,0 +1,6 @@
+HMIBSC BOARD
+M: Sumit Garg <sumit.garg at linaro.org>
+S: Maintained
+F: board/schneider/hmibsc/
+F: include/configs/hmibsc.h
+F: configs/hmibsc_defconfig
diff --git a/configs/hmibsc_defconfig b/configs/hmibsc_defconfig
new file mode 100644
index 00000000000..c41ed3d5925
--- /dev/null
+++ b/configs/hmibsc_defconfig
@@ -0,0 +1,86 @@
+CONFIG_ARM=y
+CONFIG_SYS_BOARD="hmibsc"
+CONFIG_ENABLE_ARM_SOC_BOOT0_HOOK=y
+CONFIG_ARCH_SNAPDRAGON=y
+CONFIG_TEXT_BASE=0x8f600000
+CONFIG_SYS_MALLOC_LEN=0x802000
+CONFIG_HAS_CUSTOM_SYS_INIT_SP_ADDR=y
+CONFIG_CUSTOM_SYS_INIT_SP_ADDR=0x8007fff0
+CONFIG_ENV_SIZE=0x2000
+CONFIG_ENV_OFFSET=0x0
+CONFIG_DEFAULT_DEVICE_TREE="apq8016-schneider-hmibsc"
+# CONFIG_OF_UPSTREAM is not set
+CONFIG_OF_LIBFDT_OVERLAY=y
+CONFIG_IDENT_STRING="\nSchneider Electric-HMIBSC"
+CONFIG_SYS_LOAD_ADDR=0x80080000
+CONFIG_REMAKE_ELF=y
+# CONFIG_ANDROID_BOOT_IMAGE is not set
+CONFIG_FIT=y
+CONFIG_HUSH_PARSER=y
+CONFIG_SYS_CBSIZE=2048
+# CONFIG_DISPLAY_CPUINFO is not set
+# CONFIG_DISPLAY_BOARDINFO is not set
+CONFIG_SYS_PROMPT="hmibsc => "
+CONFIG_SYS_MAXARGS=64
+CONFIG_CMD_DHCP=y
+CONFIG_CMD_PING=y
+CONFIG_CMD_FS_GENERIC=y
+# CONFIG_CMD_IMI is not set
+CONFIG_CMD_MD5SUM=y
+CONFIG_CMD_MEMINFO=y
+CONFIG_CMD_EXT2=y
+CONFIG_CMD_EXT4=y
+CONFIG_CMD_FAT=y
+CONFIG_CMD_GPIO=y
+CONFIG_CMD_GPT=y
+CONFIG_CMD_MMC=y
+CONFIG_CMD_PART=y
+CONFIG_CMD_USB=y
+CONFIG_BOOTP_BOOTFILESIZE=y
+CONFIG_CMD_CACHE=y
+CONFIG_CMD_TIMER=y
+CONFIG_CMD_ENV_FLAGS=y
+CONFIG_CMD_ENV_EXISTS=y
+CONFIG_CMD_NVEDIT_INFO=y
+CONFIG_ENV_WRITEABLE_LIST=y
+CONFIG_ENV_ACCESS_IGNORE_FORCE=y
+CONFIG_ENV_IS_IN_MMC=y
+CONFIG_SYS_RELOC_GD_ENV_ADDR=y
+CONFIG_SYS_MMC_ENV_PART=2
+CONFIG_BUTTON_QCOM_PMIC=y
+CONFIG_CLK=y
+CONFIG_CLK_QCOM_APQ8016=y
+CONFIG_USB_FUNCTION_FASTBOOT=y
+CONFIG_FASTBOOT_BUF_ADDR=0x91000000
+CONFIG_FASTBOOT_FLASH=y
+CONFIG_FASTBOOT_FLASH_MMC_DEV=0
+CONFIG_MSM_GPIO=y
+CONFIG_QCOM_PMIC_GPIO=y
+CONFIG_LED=y
+CONFIG_LED_GPIO=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_MSM=y
+CONFIG_PHY=y
+CONFIG_PINCTRL=y
+CONFIG_PINCONF=y
+CONFIG_PINCTRL_QCOM_APQ8016=y
+CONFIG_DM_PMIC=y
+CONFIG_PMIC_QCOM=y
+CONFIG_MSM_SERIAL=y
+CONFIG_SPMI_MSM=y
+CONFIG_USB=y
+CONFIG_USB_EHCI_HCD=y
+CONFIG_USB_EHCI_MSM=y
+CONFIG_USB_ULPI_VIEWPORT=y
+CONFIG_USB_ULPI=y
+CONFIG_USB_HOST_ETHER=y
+CONFIG_USB_ETHER_ASIX=y
+CONFIG_USB_ETHER_ASIX88179=y
+CONFIG_USB_ETHER_MCS7830=y
+CONFIG_USB_ETHER_SMSC95XX=y
+CONFIG_PHYLIB=y
+CONFIG_USB_ETHER_LAN75XX=y
+CONFIG_USB_GADGET=y
+CONFIG_USB_GADGET_VENDOR_NUM=0x18d1
+CONFIG_USB_GADGET_PRODUCT_NUM=0xd00d
+CONFIG_CI_UDC=y
diff --git a/doc/board/index.rst b/doc/board/index.rst
index f0a11f84ccc..428faa810be 100644
--- a/doc/board/index.rst
+++ b/doc/board/index.rst
@@ -42,6 +42,7 @@ Board-specific doc
renesas/index
rockchip/index
samsung/index
+ schneider/index
sielaff/index
siemens/index
sifive/index
diff --git a/doc/board/schneider/hmibsc.rst b/doc/board/schneider/hmibsc.rst
new file mode 100644
index 00000000000..f09fb5af1b3
--- /dev/null
+++ b/doc/board/schneider/hmibsc.rst
@@ -0,0 +1,45 @@
+.. SPDX-License-Identifier: GPL-2.0+
+.. sectionauthor:: Sumit Garg <sumit.garg at linaro.org>
+
+HMIBSC
+======
+
+The HMIBSC is an IIoT Edge Box Core board based on the Qualcomm APQ8016E SoC.
+More information can be found on the `SE product page`_.
+
+U-Boot can be used as a replacement for Qualcomm's original Android bootloader
+(a fork of Little Kernel/LK). Like LK, it is installed directly into the ``aboot``
+partition. Note that the U-Boot port used to be loaded as an Android boot image
+through LK. This is no longer the case, now U-Boot can replace LK entirely.
+
+.. _SE product page: https://www.se.com/us/en/product/HMIBSCEA53D1L0T/iiot-edge-box-core-harmony-ipc-emmc-dc-linux-tpm/
+
+Build steps
+-----------
+
+First, setup ``CROSS_COMPILE`` for aarch64. Then, build U-Boot for ``hmibsc``::
+
+ $ export CROSS_COMPILE=<aarch64 toolchain prefix>
+ $ make hmibsc_defconfig
+ $ make
+
+This will build ``u-boot.elf`` in the configured output directory.
+
+Installation
+------------
+
+Although the HMIBSC does not have secure boot set up by default, the firmware
+still expects firmware ELF images to be "signed". The signature does not provide
+any security in this case, but it provides the firmware with some required
+metadata.
+
+To "sign" ``u-boot.elf`` you can use e.g. `qtestsign`_::
+
+ $ ./qtestsign.py aboot u-boot.elf
+
+Then install the resulting ``u-boot-test-signed.mbn`` to the ``aboot`` partition
+on your device, e.g. with ``fastboot flash aboot u-boot-test-signed.mbn``.
+
+U-Boot should be running after a reboot (``fastboot reboot``).
+
+.. _qtestsign: https://github.com/msm8916-mainline/qtestsign
diff --git a/doc/board/schneider/index.rst b/doc/board/schneider/index.rst
new file mode 100644
index 00000000000..55792ed3100
--- /dev/null
+++ b/doc/board/schneider/index.rst
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0+
+
+Schneider Electric
+==================
+
+.. toctree::
+ :maxdepth: 2
+
+ hmibsc
diff --git a/include/configs/hmibsc.h b/include/configs/hmibsc.h
new file mode 100644
index 00000000000..66dfa549ce1
--- /dev/null
+++ b/include/configs/hmibsc.h
@@ -0,0 +1,57 @@
+/* SPDX-License-Identifier: GPL-2.0+ */
+/*
+ * Board configuration file for HMIBSC
+ *
+ * (C) Copyright 2024 Sumit Garg <sumit.garg at linaro.org>
+ */
+
+#ifndef __CONFIGS_HMIBSC_H
+#define __CONFIGS_HMIBSC_H
+
+/* PHY needs a longer aneg time */
+#define PHY_ANEG_TIMEOUT 8000
+
+#define HMIBSC_BOOTCOMMAND \
+ "setenv devtype mmc; setenv devnum 0; " \
+ "test -n \"${BOOT_ORDER}\" || setenv BOOT_ORDER \"A B\"; " \
+ "test -n \"${BOOT_A_LEFT}\" || setenv BOOT_A_LEFT 3; " \
+ "test -n \"${BOOT_B_LEFT}\" || setenv BOOT_B_LEFT 3; " \
+ "setenv raucslot; " \
+ "for BOOT_SLOT in \"${BOOT_ORDER}\"; do " \
+ " if test \"x${raucslot}\" != \"x\"; then " \
+ " echo \"skip remaining slots...\"; " \
+ " elif test \"x${BOOT_SLOT}\" = \"xA\"; then " \
+ " if test ${BOOT_A_LEFT} -gt 0; then " \
+ " setexpr BOOT_A_LEFT ${BOOT_A_LEFT} - 1; " \
+ " echo \"Found valid RAUC slot A\"; " \
+ " setenv raucslot \"rauc.slot=A\"; " \
+ " setenv raucpart A; setenv distro_bootpart 6;" \
+ " fi; " \
+ " elif test \"x${BOOT_SLOT}\" = \"xB\"; then " \
+ " if test ${BOOT_B_LEFT} -gt 0; then " \
+ " setexpr BOOT_B_LEFT ${BOOT_B_LEFT} - 1; " \
+ " echo \"Found valid RAUC slot B\"; " \
+ " setenv raucslot \"rauc.slot=B\"; " \
+ " setenv raucpart B; setenv distro_bootpart 7;" \
+ " fi; " \
+ " fi; " \
+ "done; " \
+ "if test -n \"${raucslot}\"; then " \
+ " setenv bootargs console=ttyMSM1 root=PARTLABEL=rootfs_${raucpart} rw rootwait ${raucslot}; " \
+ " saveenv; " \
+ "else " \
+ " echo \"No valid RAUC slot found. Resetting tries to 3\"; " \
+ " setenv BOOT_A_LEFT 3; " \
+ " setenv BOOT_B_LEFT 3; " \
+ " saveenv; " \
+ " reset; " \
+ "fi; " \
+ "load ${devtype} ${devnum}:${distro_bootpart} ${loadaddr} /boot/fitImage && bootm"
+
+#define CFG_EXTRA_ENV_SETTINGS \
+ "loadaddr=0x90000000\0" \
+ "bootcmd=" HMIBSC_BOOTCOMMAND "\0"
+
+#define CFG_ENV_FLAGS_LIST_STATIC "BOOT_A_LEFT:dw,BOOT_B_LEFT:dw,BOOT_ORDER:sw"
+
+#endif
--
2.34.1
More information about the U-Boot
mailing list