[PATCH v2 1/2] phy: qcom: add Synopsys eUSB2 PHY driver
Neil Armstrong
neil.armstrong at linaro.org
Wed Apr 10 18:01:12 CEST 2024
Add a driver for the new Synopsys eUSB2 PHY found in the SM8550
and SM8650 SoCs.
Signed-off-by: Neil Armstrong <neil.armstrong at linaro.org>
---
drivers/phy/qcom/Kconfig | 8 +
drivers/phy/qcom/Makefile | 1 +
drivers/phy/qcom/phy-qcom-snps-eusb2.c | 366 +++++++++++++++++++++++++++++++++
3 files changed, 375 insertions(+)
diff --git a/drivers/phy/qcom/Kconfig b/drivers/phy/qcom/Kconfig
index b9fe608c279..3aae1813352 100644
--- a/drivers/phy/qcom/Kconfig
+++ b/drivers/phy/qcom/Kconfig
@@ -27,6 +27,14 @@ config PHY_QCOM_USB_SNPS_FEMTO_V2
High-Speed PHY driver. This driver supports the Hi-Speed PHY which
is usually paired with Synopsys DWC3 USB IPs on MSM SOCs.
+config PHY_QCOM_SNPS_EUSB2
+ tristate "Qualcomm Synopsys eUSB2 High-Speed PHY"
+ depends on PHY && ARCH_SNAPDRAGON
+ help
+ Enable this to support the Qualcomm Synopsys DesignWare eUSB2
+ High-Speed PHY driver. This driver supports the Hi-Speed PHY which
+ is usually paired with Synopsys DWC3 USB IPs on MSM SOCs.
+
config PHY_QCOM_USB_HS_28NM
tristate "Qualcomm 28nm High-Speed PHY"
depends on PHY && ARCH_SNAPDRAGON
diff --git a/drivers/phy/qcom/Makefile b/drivers/phy/qcom/Makefile
index 5f4db4a5378..a5153061dfb 100644
--- a/drivers/phy/qcom/Makefile
+++ b/drivers/phy/qcom/Makefile
@@ -2,5 +2,6 @@ obj-$(CONFIG_PHY_QCOM_IPQ4019_USB) += phy-qcom-ipq4019-usb.o
obj-$(CONFIG_MSM8916_USB_PHY) += msm8916-usbh-phy.o
obj-$(CONFIG_PHY_QCOM_QUSB2) += phy-qcom-qusb2.o
obj-$(CONFIG_PHY_QCOM_USB_SNPS_FEMTO_V2) += phy-qcom-snps-femto-v2.o
+obj-$(CONFIG_PHY_QCOM_SNPS_EUSB2) += phy-qcom-snps-eusb2.o
obj-$(CONFIG_PHY_QCOM_USB_HS_28NM) += phy-qcom-usb-hs-28nm.o
obj-$(CONFIG_PHY_QCOM_USB_SS) += phy-qcom-usb-ss.o
diff --git a/drivers/phy/qcom/phy-qcom-snps-eusb2.c b/drivers/phy/qcom/phy-qcom-snps-eusb2.c
new file mode 100644
index 00000000000..b2655ac007c
--- /dev/null
+++ b/drivers/phy/qcom/phy-qcom-snps-eusb2.c
@@ -0,0 +1,366 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2023-2024, Linaro Limited
+ *
+ * Based on the Linux phy-qcom-snps-eusb2.c driver
+ */
+
+#include <clk.h>
+#include <clk-uclass.h>
+#include <dm.h>
+#include <dm/device_compat.h>
+#include <dm/devres.h>
+#include <generic-phy.h>
+#include <malloc.h>
+#include <reset.h>
+
+#include <asm/io.h>
+#include <linux/bitops.h>
+#include <linux/bitfield.h>
+#include <linux/clk-provider.h>
+#include <linux/delay.h>
+
+#define USB_PHY_UTMI_CTRL0 (0x3c)
+#define SLEEPM BIT(0)
+#define OPMODE_MASK GENMASK(4, 3)
+#define OPMODE_NONDRIVING BIT(3)
+
+#define USB_PHY_UTMI_CTRL5 (0x50)
+#define POR BIT(1)
+
+#define USB_PHY_HS_PHY_CTRL_COMMON0 (0x54)
+#define PHY_ENABLE BIT(0)
+#define SIDDQ_SEL BIT(1)
+#define SIDDQ BIT(2)
+#define RETENABLEN BIT(3)
+#define FSEL_MASK GENMASK(6, 4)
+#define FSEL_19_2_MHZ_VAL (0x0)
+#define FSEL_38_4_MHZ_VAL (0x4)
+
+#define USB_PHY_CFG_CTRL_1 (0x58)
+#define PHY_CFG_PLL_CPBIAS_CNTRL_MASK GENMASK(7, 1)
+
+#define USB_PHY_CFG_CTRL_2 (0x5c)
+#define PHY_CFG_PLL_FB_DIV_7_0_MASK GENMASK(7, 0)
+#define DIV_7_0_19_2_MHZ_VAL (0x90)
+#define DIV_7_0_38_4_MHZ_VAL (0xc8)
+
+#define USB_PHY_CFG_CTRL_3 (0x60)
+#define PHY_CFG_PLL_FB_DIV_11_8_MASK GENMASK(3, 0)
+#define DIV_11_8_19_2_MHZ_VAL (0x1)
+#define DIV_11_8_38_4_MHZ_VAL (0x0)
+
+#define PHY_CFG_PLL_REF_DIV GENMASK(7, 4)
+#define PLL_REF_DIV_VAL (0x0)
+
+#define USB_PHY_HS_PHY_CTRL2 (0x64)
+#define VBUSVLDEXT0 BIT(0)
+#define USB2_SUSPEND_N BIT(2)
+#define USB2_SUSPEND_N_SEL BIT(3)
+#define VBUS_DET_EXT_SEL BIT(4)
+
+#define USB_PHY_CFG_CTRL_4 (0x68)
+#define PHY_CFG_PLL_GMP_CNTRL_MASK GENMASK(1, 0)
+#define PHY_CFG_PLL_INT_CNTRL_MASK GENMASK(7, 2)
+
+#define USB_PHY_CFG_CTRL_5 (0x6c)
+#define PHY_CFG_PLL_PROP_CNTRL_MASK GENMASK(4, 0)
+#define PHY_CFG_PLL_VREF_TUNE_MASK GENMASK(7, 6)
+
+#define USB_PHY_CFG_CTRL_6 (0x70)
+#define PHY_CFG_PLL_VCO_CNTRL_MASK GENMASK(2, 0)
+
+#define USB_PHY_CFG_CTRL_7 (0x74)
+
+#define USB_PHY_CFG_CTRL_8 (0x78)
+#define PHY_CFG_TX_FSLS_VREF_TUNE_MASK GENMASK(1, 0)
+#define PHY_CFG_TX_FSLS_VREG_BYPASS BIT(2)
+#define PHY_CFG_TX_HS_VREF_TUNE_MASK GENMASK(5, 3)
+#define PHY_CFG_TX_HS_XV_TUNE_MASK GENMASK(7, 6)
+
+#define USB_PHY_CFG_CTRL_9 (0x7c)
+#define PHY_CFG_TX_PREEMP_TUNE_MASK GENMASK(2, 0)
+#define PHY_CFG_TX_RES_TUNE_MASK GENMASK(4, 3)
+#define PHY_CFG_TX_RISE_TUNE_MASK GENMASK(6, 5)
+#define PHY_CFG_RCAL_BYPASS BIT(7)
+
+#define USB_PHY_CFG_CTRL_10 (0x80)
+
+#define USB_PHY_CFG0 (0x94)
+#define DATAPATH_CTRL_OVERRIDE_EN BIT(0)
+#define CMN_CTRL_OVERRIDE_EN BIT(1)
+
+#define UTMI_PHY_CMN_CTRL0 (0x98)
+#define TESTBURNIN BIT(6)
+
+#define USB_PHY_FSEL_SEL (0xb8)
+#define FSEL_SEL BIT(0)
+
+#define USB_PHY_APB_ACCESS_CMD (0x130)
+#define RW_ACCESS BIT(0)
+#define APB_START_CMD BIT(1)
+#define APB_LOGIC_RESET BIT(2)
+
+#define USB_PHY_APB_ACCESS_STATUS (0x134)
+#define ACCESS_DONE BIT(0)
+#define TIMED_OUT BIT(1)
+#define ACCESS_ERROR BIT(2)
+#define ACCESS_IN_PROGRESS BIT(3)
+
+#define USB_PHY_APB_ADDRESS (0x138)
+#define APB_REG_ADDR_MASK GENMASK(7, 0)
+
+#define USB_PHY_APB_WRDATA_LSB (0x13c)
+#define APB_REG_WRDATA_7_0_MASK GENMASK(3, 0)
+
+#define USB_PHY_APB_WRDATA_MSB (0x140)
+#define APB_REG_WRDATA_15_8_MASK GENMASK(7, 4)
+
+#define USB_PHY_APB_RDDATA_LSB (0x144)
+#define APB_REG_RDDATA_7_0_MASK GENMASK(3, 0)
+
+#define USB_PHY_APB_RDDATA_MSB (0x148)
+#define APB_REG_RDDATA_15_8_MASK GENMASK(7, 4)
+
+struct qcom_snps_eusb2_phy_priv {
+ void __iomem *base;
+ struct clk *ref_clk;
+ struct reset_ctl_bulk resets;
+};
+
+static void qcom_snps_eusb2_hsphy_write_mask(void __iomem *base, u32 offset,
+ u32 mask, u32 val)
+{
+ u32 reg;
+
+ reg = readl_relaxed(base + offset);
+ reg &= ~mask;
+ reg |= val & mask;
+ writel_relaxed(reg, base + offset);
+
+ /* Ensure above write is completed */
+ readl_relaxed(base + offset);
+}
+
+static void qcom_eusb2_default_parameters(struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2)
+{
+ /* default parameters: tx pre-emphasis */
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_9,
+ PHY_CFG_TX_PREEMP_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_TX_PREEMP_TUNE_MASK, 0));
+
+ /* tx rise/fall time */
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_9,
+ PHY_CFG_TX_RISE_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_TX_RISE_TUNE_MASK, 0x2));
+
+ /* source impedance adjustment */
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_9,
+ PHY_CFG_TX_RES_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_TX_RES_TUNE_MASK, 0x1));
+
+ /* dc voltage level adjustement */
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_8,
+ PHY_CFG_TX_HS_VREF_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_TX_HS_VREF_TUNE_MASK, 0x3));
+
+ /* transmitter HS crossover adjustement */
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_8,
+ PHY_CFG_TX_HS_XV_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_TX_HS_XV_TUNE_MASK, 0x0));
+}
+
+static int qcom_eusb2_ref_clk_init(struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2)
+{
+ unsigned long ref_clk_freq = clk_get_rate(qcom_snps_eusb2->ref_clk);
+
+ switch (ref_clk_freq) {
+ case 19200000:
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL_COMMON0,
+ FSEL_MASK,
+ FIELD_PREP(FSEL_MASK, FSEL_19_2_MHZ_VAL));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_2,
+ PHY_CFG_PLL_FB_DIV_7_0_MASK,
+ DIV_7_0_19_2_MHZ_VAL);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_3,
+ PHY_CFG_PLL_FB_DIV_11_8_MASK,
+ DIV_11_8_19_2_MHZ_VAL);
+ break;
+
+ case 38400000:
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL_COMMON0,
+ FSEL_MASK,
+ FIELD_PREP(FSEL_MASK, FSEL_38_4_MHZ_VAL));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_2,
+ PHY_CFG_PLL_FB_DIV_7_0_MASK,
+ DIV_7_0_38_4_MHZ_VAL);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_3,
+ PHY_CFG_PLL_FB_DIV_11_8_MASK,
+ DIV_11_8_38_4_MHZ_VAL);
+ break;
+
+ default:
+ printf("%s: unsupported ref_clk_freq:%lu\n", __func__, ref_clk_freq);
+ return -EINVAL;
+ }
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_3,
+ PHY_CFG_PLL_REF_DIV, PLL_REF_DIV_VAL);
+
+ return 0;
+}
+
+static int qcom_snps_eusb2_usb_init(struct phy *phy)
+{
+ struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2 = dev_get_priv(phy->dev);
+ int ret;
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG0,
+ CMN_CTRL_OVERRIDE_EN, CMN_CTRL_OVERRIDE_EN);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_UTMI_CTRL5, POR, POR);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL_COMMON0,
+ PHY_ENABLE | RETENABLEN, PHY_ENABLE | RETENABLEN);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_APB_ACCESS_CMD,
+ APB_LOGIC_RESET, APB_LOGIC_RESET);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, UTMI_PHY_CMN_CTRL0, TESTBURNIN, 0);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_FSEL_SEL,
+ FSEL_SEL, FSEL_SEL);
+
+ /* update ref_clk related registers */
+ ret = qcom_eusb2_ref_clk_init(qcom_snps_eusb2);
+ if (ret)
+ return ret;
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_1,
+ PHY_CFG_PLL_CPBIAS_CNTRL_MASK,
+ FIELD_PREP(PHY_CFG_PLL_CPBIAS_CNTRL_MASK, 0x1));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_4,
+ PHY_CFG_PLL_INT_CNTRL_MASK,
+ FIELD_PREP(PHY_CFG_PLL_INT_CNTRL_MASK, 0x8));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_4,
+ PHY_CFG_PLL_GMP_CNTRL_MASK,
+ FIELD_PREP(PHY_CFG_PLL_GMP_CNTRL_MASK, 0x1));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_5,
+ PHY_CFG_PLL_PROP_CNTRL_MASK,
+ FIELD_PREP(PHY_CFG_PLL_PROP_CNTRL_MASK, 0x10));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_6,
+ PHY_CFG_PLL_VCO_CNTRL_MASK,
+ FIELD_PREP(PHY_CFG_PLL_VCO_CNTRL_MASK, 0x0));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_CFG_CTRL_5,
+ PHY_CFG_PLL_VREF_TUNE_MASK,
+ FIELD_PREP(PHY_CFG_PLL_VREF_TUNE_MASK, 0x1));
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL2,
+ VBUS_DET_EXT_SEL, VBUS_DET_EXT_SEL);
+
+ /* set default parameters */
+ qcom_eusb2_default_parameters(qcom_snps_eusb2);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL2,
+ USB2_SUSPEND_N_SEL | USB2_SUSPEND_N,
+ USB2_SUSPEND_N_SEL | USB2_SUSPEND_N);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_UTMI_CTRL0, SLEEPM, SLEEPM);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL_COMMON0,
+ SIDDQ_SEL, SIDDQ_SEL);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL_COMMON0,
+ SIDDQ, 0);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_UTMI_CTRL5, POR, 0);
+
+ qcom_snps_eusb2_hsphy_write_mask(qcom_snps_eusb2->base, USB_PHY_HS_PHY_CTRL2,
+ USB2_SUSPEND_N_SEL, 0);
+
+ return 0;
+}
+
+static int qcom_snps_eusb2_phy_power_on(struct phy *phy)
+{
+ struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2 = dev_get_priv(phy->dev);
+ int ret;
+
+ /* TODO Repeater */
+
+ clk_prepare_enable(qcom_snps_eusb2->ref_clk);
+
+ ret = reset_deassert_bulk(&qcom_snps_eusb2->resets);
+ if (ret)
+ return ret;
+
+ ret = qcom_snps_eusb2_usb_init(phy);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static int qcom_snps_eusb2_phy_power_off(struct phy *phy)
+{
+ struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2 = dev_get_priv(phy->dev);
+
+ reset_assert_bulk(&qcom_snps_eusb2->resets);
+ clk_disable_unprepare(qcom_snps_eusb2->ref_clk);
+
+ return 0;
+}
+
+static int qcom_snps_eusb2_phy_probe(struct udevice *dev)
+{
+ struct qcom_snps_eusb2_phy_priv *qcom_snps_eusb2 = dev_get_priv(dev);
+ int ret;
+
+ qcom_snps_eusb2->base = (void __iomem *)dev_read_addr(dev);
+ if (IS_ERR(qcom_snps_eusb2->base))
+ return PTR_ERR(qcom_snps_eusb2->base);
+
+ qcom_snps_eusb2->ref_clk = devm_clk_get(dev, "ref");
+ if (IS_ERR(qcom_snps_eusb2->ref_clk)) {
+ printf("%s: failed to get ref clk %d\n", __func__, ret);
+ return PTR_ERR(qcom_snps_eusb2->ref_clk);
+ }
+
+ ret = reset_get_bulk(dev, &qcom_snps_eusb2->resets);
+ if (ret < 0) {
+ printf("failed to get resets, ret = %d\n", ret);
+ return ret;
+ }
+
+ return 0;
+}
+
+static struct phy_ops qcom_snps_eusb2_phy_ops = {
+ .power_on = qcom_snps_eusb2_phy_power_on,
+ .power_off = qcom_snps_eusb2_phy_power_off,
+};
+
+static const struct udevice_id qcom_snps_eusb2_phy_ids[] = {
+ {
+ .compatible = "qcom,sm8550-snps-eusb2-phy",
+ },
+ {}
+};
+
+U_BOOT_DRIVER(qcom_usb_qcom_snps_eusb2) = {
+ .name = "qcom-snps-eusb2-hsphy",
+ .id = UCLASS_PHY,
+ .of_match = qcom_snps_eusb2_phy_ids,
+ .ops = &qcom_snps_eusb2_phy_ops,
+ .probe = qcom_snps_eusb2_phy_probe,
+ .priv_auto = sizeof(struct qcom_snps_eusb2_phy_priv),
+};
--
2.34.1
More information about the U-Boot
mailing list