[PATCH 12/12] rockchip: rk3399: Drop unneeded bob and kevin board specific code

[Jonas Karlman]

The IO-domain driver will configure io_vsel and always-on/boot-on
regulators will be enabled based on the board device tree now that
required nodes and Kconfig options is enabled for SPL.

Remove the bob and kevin board specific code from the common rk3399.c,
the IO-domain and regulator driver provide similar functionality.

Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
---
 arch/arm/mach-rockchip/rk3399/rk3399.c | 23 +----------------------
 1 file changed, 1 insertion(+), 22 deletions(-)

diff --git a/arch/arm/mach-rockchip/rk3399/rk3399.c b/arch/arm/mach-rockchip/rk3399/rk3399.c
index ba89079b1e73..1ce43c6f0d40 100644
--- a/arch/arm/mach-rockchip/rk3399/rk3399.c
+++ b/arch/arm/mach-rockchip/rk3399/rk3399.c
@@ -7,7 +7,6 @@
 #include <init.h>
 #include <log.h>
 #include <spl.h>
-#include <spl_gpio.h>
 #include <syscon.h>
 #include <asm/armv8/mmu.h>
 #include <asm/arch-rockchip/bootrom.h>
@@ -16,6 +15,7 @@
 #include <asm/arch-rockchip/gpio.h>
 #include <asm/arch-rockchip/grf_rk3399.h>
 #include <asm/arch-rockchip/hardware.h>
+#include <asm/gpio.h>
 #include <linux/bitops.h>
 #include <linux/printk.h>
 #include <power/regulator.h>
@@ -133,27 +133,6 @@ void board_debug_uart_init(void)
 		     GRF_GPIO3B7_SEL_MASK,
 		     GRF_UART3_SOUT << GRF_GPIO3B7_SEL_SHIFT);
 #else
-	struct rk3399_pmugrf_regs * const pmugrf = (void *)PMUGRF_BASE;
-	struct rockchip_gpio_regs * const gpio = (void *)GPIO0_BASE;
-
-	if (IS_ENABLED(CONFIG_SPL_BUILD) &&
-	    (IS_ENABLED(CONFIG_TARGET_CHROMEBOOK_BOB) ||
-	     IS_ENABLED(CONFIG_TARGET_CHROMEBOOK_KEVIN))) {
-		rk_setreg(&grf->io_vsel, 1 << 0);
-
-		/*
-		 * Let's enable these power rails here, we are already running
-		 * the SPI-Flash-based code.
-		 */
-		spl_gpio_output(gpio, GPIO(BANK_B, 2), 1);  /* PP1500_EN */
-		spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 2),
-				  GPIO_PULL_NORMAL);
-
-		spl_gpio_output(gpio, GPIO(BANK_B, 4), 1);  /* PP3000_EN */
-		spl_gpio_set_pull(&pmugrf->gpio0_p, GPIO(BANK_B, 4),
-				  GPIO_PULL_NORMAL);
-	}
-
 	/* Enable early UART2 channel C on the RK3399 */
 	rk_clrsetreg(&grf->gpio4c_iomux,
 		     GRF_GPIO4C3_SEL_MASK,
-- 
2.47.1