[PATCH 3/4] mtd: nand: raw: Fix (most) Kconfig indentation
Michael Nazzareno Trimarchi
michael at amarulasolutions.com
Thu Mar 7 11:03:21 CET 2024
Hi
On Thu, Mar 7, 2024 at 10:10 AM Alexander Dahl <ada at thorsis.com> wrote:
>
> One tab in general. One tab plus two spaces for help text.
>
> Signed-off-by: Alexander Dahl <ada at thorsis.com>
> ---
> drivers/mtd/nand/raw/Kconfig | 106 +++++++++++++++++------------------
> 1 file changed, 53 insertions(+), 53 deletions(-)
>
> diff --git a/drivers/mtd/nand/raw/Kconfig b/drivers/mtd/nand/raw/Kconfig
> index bb9994b8626..f6644899b0a 100644
> --- a/drivers/mtd/nand/raw/Kconfig
> +++ b/drivers/mtd/nand/raw/Kconfig
> @@ -1,6 +1,6 @@
> -
> menuconfig MTD_RAW_NAND
> bool "Raw NAND Device Support"
> +
> if MTD_RAW_NAND
>
> config SYS_NAND_SELF_INIT
> @@ -49,12 +49,12 @@ config SYS_NAND_NO_SUBPAGE_WRITE
> depends on NAND_ARASAN || NAND_DAVINCI || NAND_KIRKWOOD
>
> config DM_NAND_ATMEL
> - bool "Support Atmel NAND controller with DM support"
> - select SYS_NAND_SELF_INIT
> - imply SYS_NAND_USE_FLASH_BBT
> - help
> - Enable this driver for NAND flash platforms using an Atmel NAND
> - controller.
> + bool "Support Atmel NAND controller with DM support"
> + select SYS_NAND_SELF_INIT
> + imply SYS_NAND_USE_FLASH_BBT
> + help
> + Enable this driver for NAND flash platforms using an Atmel NAND
> + controller.
>
> config NAND_ATMEL
> bool "Support Atmel NAND controller"
> @@ -133,35 +133,35 @@ config NAND_BRCMNAND_6753
> Enable support for broadcom nand driver on bcm6753.
>
> config NAND_BRCMNAND_68360
> - bool "Support Broadcom NAND controller on bcm68360"
> - depends on NAND_BRCMNAND && BCM6856
> - help
> - Enable support for broadcom nand driver on bcm68360.
> + bool "Support Broadcom NAND controller on bcm68360"
> + depends on NAND_BRCMNAND && BCM6856
> + help
> + Enable support for broadcom nand driver on bcm68360.
>
> config NAND_BRCMNAND_6838
> - bool "Support Broadcom NAND controller on bcm6838"
> - depends on NAND_BRCMNAND && ARCH_BMIPS && SOC_BMIPS_BCM6838
> - help
> - Enable support for broadcom nand driver on bcm6838.
> + bool "Support Broadcom NAND controller on bcm6838"
> + depends on NAND_BRCMNAND && ARCH_BMIPS && SOC_BMIPS_BCM6838
> + help
> + Enable support for broadcom nand driver on bcm6838.
>
> config NAND_BRCMNAND_6858
> - bool "Support Broadcom NAND controller on bcm6858"
> - depends on NAND_BRCMNAND && BCM6858
> - help
> - Enable support for broadcom nand driver on bcm6858.
> + bool "Support Broadcom NAND controller on bcm6858"
> + depends on NAND_BRCMNAND && BCM6858
> + help
> + Enable support for broadcom nand driver on bcm6858.
>
> config NAND_BRCMNAND_63158
> - bool "Support Broadcom NAND controller on bcm63158"
> - depends on NAND_BRCMNAND && BCM63158
> - help
> - Enable support for broadcom nand driver on bcm63158.
> + bool "Support Broadcom NAND controller on bcm63158"
> + depends on NAND_BRCMNAND && BCM63158
> + help
> + Enable support for broadcom nand driver on bcm63158.
>
> config NAND_BRCMNAND_IPROC
> - bool "Support Broadcom NAND controller on the iproc family"
> - depends on NAND_BRCMNAND
> - help
> - Enable support for broadcom nand driver on the Broadcom
> - iproc family such as Northstar (BCM5301x, BCM4708...)
> + bool "Support Broadcom NAND controller on the iproc family"
> + depends on NAND_BRCMNAND
> + help
> + Enable support for broadcom nand driver on the Broadcom
> + iproc family such as Northstar (BCM5301x, BCM4708...)
>
> config NAND_DAVINCI
> bool "Support TI Davinci NAND controller"
> @@ -413,10 +413,10 @@ config NAND_VF610_NFC
> if NAND_VF610_NFC
>
> config NAND_VF610_NFC_DT
> - bool "Support Vybrid's vf610 NAND controller as a DT device"
> - depends on OF_CONTROL && DM_MTD
> - help
> - Enable the driver for Vybrid's vf610 NAND flash on platforms
> + bool "Support Vybrid's vf610 NAND controller as a DT device"
> + depends on OF_CONTROL && DM_MTD
> + help
> + Enable the driver for Vybrid's vf610 NAND flash on platforms
> using device tree.
>
> choice
> @@ -472,11 +472,11 @@ config NAND_SUNXI
> select SPL_NAND_SUPPORT
> select SPL_SYS_NAND_SELF_INIT
> imply CMD_NAND
> - ---help---
> - Enable support for NAND. This option enables the standard and
> - SPL drivers.
> - The SPL driver only supports reading from the NAND using DMA
> - transfers.
> + help
> + Enable support for NAND. This option enables the standard and
> + SPL drivers.
> + The SPL driver only supports reading from the NAND using DMA
> + transfers.
>
> if NAND_SUNXI
>
> @@ -577,16 +577,16 @@ config NAND_OCTEONTX
> select SYS_NAND_SELF_INIT
> imply CMD_NAND
> help
> - This enables Nand flash controller hardware found on the OcteonTX
> - processors.
> + This enables Nand flash controller hardware found on the OcteonTX
> + processors.
>
> config NAND_OCTEONTX_HW_ECC
> bool "Support Hardware ECC for OcteonTX NAND controller"
> depends on NAND_OCTEONTX
> default y
> help
> - This enables Hardware BCH engine found on the OcteonTX processors to
> - support ECC for NAND flash controller.
> + This enables Hardware BCH engine found on the OcteonTX processors to
> + support ECC for NAND flash controller.
>
> config NAND_STM32_FMC2
> bool "Support for NAND controller on STM32MP SoCs"
> @@ -751,37 +751,37 @@ config SYS_NAND_BAD_BLOCK_POS
> config SYS_NAND_U_BOOT_LOCATIONS
> bool "Define U-Boot binaries locations in NAND"
> help
> - Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
> - This option should not be enabled when compiling U-Boot for boards
> - defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
> - file.
> + Enable CONFIG_SYS_NAND_U_BOOT_OFFS though Kconfig.
> + This option should not be enabled when compiling U-Boot for boards
> + defining CONFIG_SYS_NAND_U_BOOT_OFFS in their include/configs/<board>.h
> + file.
>
> config SYS_NAND_U_BOOT_OFFS
> hex "Location in NAND to read U-Boot from"
> default 0x800000 if NAND_SUNXI
> depends on SYS_NAND_U_BOOT_LOCATIONS
> help
> - Set the offset from the start of the nand where u-boot should be
> - loaded from.
> + Set the offset from the start of the nand where u-boot should be
> + loaded from.
>
> config SYS_NAND_U_BOOT_OFFS_REDUND
> hex "Location in NAND to read U-Boot from"
> default SYS_NAND_U_BOOT_OFFS
> depends on SYS_NAND_U_BOOT_LOCATIONS
> help
> - Set the offset from the start of the nand where the redundant u-boot
> - should be loaded from.
> + Set the offset from the start of the nand where the redundant u-boot
> + should be loaded from.
>
> config SPL_NAND_AM33XX_BCH
> bool "Enables SPL-NAND driver which supports ELM based"
> depends on SPL_NAND_SUPPORT && NAND_OMAP_GPMC && !OMAP34XX
> default y
> - help
> + help
> Hardware ECC correction. This is useful for platforms which have ELM
> hardware engine and use NAND boot mode.
> Some legacy platforms like OMAP3xx do not have in-built ELM h/w engine,
> so those platforms should use CONFIG_SPL_NAND_SIMPLE for enabling
> - SPL-NAND driver with software ECC correction support.
> + SPL-NAND driver with software ECC correction support.
>
> config SPL_NAND_DENALI
> bool "Support Denali NAND controller for SPL"
> @@ -810,6 +810,6 @@ config SYS_NAND_HW_ECC_OOBFIRST
> bool "In SPL, read the OOB first and then the data from NAND"
> depends on SPL_NAND_SIMPLE
>
> -endif
> +endif # if SPL
>
> -endif # if NAND
> +endif # if MTD_RAW_NAND
> --
> 2.39.2
>
Reviewed-by: Michael Trimarchi <michael at amarulasolutions.com>
--
Michael Nazzareno Trimarchi
Co-Founder & Chief Executive Officer
M. +39 347 913 2170
michael at amarulasolutions.com
__________________________________
Amarula Solutions BV
Joop Geesinkweg 125, 1114 AB, Amsterdam, NL
T. +31 (0)85 111 9172
info at amarulasolutions.com
www.amarulasolutions.com
More information about the U-Boot
mailing list