[PATCH] sunxi: h616: add initial support for T95 AXP313 TV Box
Kamil Kasperski
ressetkk at gmail.com
Mon Mar 11 11:37:49 CET 2024
Hello Andre,
Thanks for your reply and thanks for pointing some stuff out.
> What is "mbox"? Do you have any more information about this vendor?
"MBOX" refers to the "Model" string from system properties.
The problem is that it's quite hard to pin the correct vendor, since
the OS is built based on Google Pixel 2.
You can see that the fingerprint contains strings only for this phone:
[ro.build.fingerprint]:
[google/walley/walleye:10/QP1A.191105.004/eng.cmj.20220408.125005:userdebug/test-keys]
Setting the device model as Vendor string seemed to be the most safe bet.
If you have any other suggestions, please let me know.
> But please note that the devicetree needs to go through the Linux
> mailing lists and repo first, and we automatically copy it from the
> Linux tree once it has been merged there.
Thanks for pointing that out. I'll contact Linux maintainers
and will send updated patch.
Best regards,
Kamil
niedz., 10 mar 2024 o 23:00 Andre Przywara <andre.przywara at arm.com> napisał(a):
>
> On Sat, 9 Mar 2024 19:24:26 +0000
> Kamil Kasperski <ressetkk at gmail.com> wrote:
>
> Hi Kamil,
>
> many thanks for sending a patch, that looks mostly good from the
> technical point of view, only some smaller comments.
>
> But please note that the devicetree needs to go through the Linux
> mailing lists and repo first, and we automatically copy it from the
> Linux tree once it has been merged there. This is to ensure proper
> review and checks with the Linux tooling.
>
> So can you please send just the .dts file to the DT and sunxi
> maintainers the respective lists, as reported by get_maintainer.pl?
> Then we can take it from there.
>
> > T95 is a most commonly known for being a box with a pre-installed malware.
> > It uses Allwinner H616 and comes with eMMC and DDR3 memory.
> > This device comes with two versions - one with AXP305 PMIC and another with AXP313 PMIC.
> > The AXP313 version comes with Secure Boot enabled and locked bootloader, so the u-boot has to be built with TOC0.
> > DRAM settings are taken from Allwinner's boot0 for this box.
>
> Ah, thanks for figuring those out, that's very helpful.
>
> >
> > Cc: Andre Przywara <andre.przywara at arm.com>
> >
> > Signed-off-by: Kamil Kasperski <ressetkk at gmail.com>
> > ---
> > arch/arm/dts/Makefile | 3 +-
> > arch/arm/dts/sun50i-h616-t95-axp313.dts | 148 ++++++++++++++++++++++++
> > configs/t95_axp313_defconfig | 27 +++++
> > 3 files changed, 177 insertions(+), 1 deletion(-)
> > create mode 100644 arch/arm/dts/sun50i-h616-t95-axp313.dts
> > create mode 100644 configs/t95_axp313_defconfig
> >
> > diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
> > index b102ffb5f6..144daf6c48 100644
> > --- a/arch/arm/dts/Makefile
> > +++ b/arch/arm/dts/Makefile
> > @@ -842,7 +842,8 @@ dtb-$(CONFIG_MACH_SUN50I_H616) += \
> > sun50i-h618-orangepi-zero2w.dtb \
> > sun50i-h618-orangepi-zero3.dtb \
> > sun50i-h618-transpeed-8k618-t.dtb \
> > - sun50i-h616-x96-mate.dtb
> > + sun50i-h616-x96-mate.dtb \
> > + sun50i-h616-t95-axp313.dtb
> > dtb-$(CONFIG_MACH_SUN50I) += \
> > sun50i-a64-amarula-relic.dtb \
> > sun50i-a64-bananapi-m64.dtb \
> > diff --git a/arch/arm/dts/sun50i-h616-t95-axp313.dts b/arch/arm/dts/sun50i-h616-t95-axp313.dts
> > new file mode 100644
> > index 0000000000..b006f363d5
> > --- /dev/null
> > +++ b/arch/arm/dts/sun50i-h616-t95-axp313.dts
> > @@ -0,0 +1,148 @@
> > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> > +/*
> > + * Copyright (C) 2021 Arm Ltd.
>
> Please change this copyright you and this year.
>
> > + */
> > +
> > +/dts-v1/;
> > +
> > +#include "sun50i-h616.dtsi"
> > +
> > +#include <dt-bindings/gpio/gpio.h>
> > +#include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +/ {
> > + model = "T95 (AXP313)";
> > + compatible = "mbox,t95-axp313", "allwinner,sun50i-h616";
>
> What is "mbox"? Do you have any more information about this vendor?
> In any case a new vendor would need to be added to
> Documentation/devicetree/bindings/vendor-prefixes.yaml, in a separate
> patch. Also you need a patch to add this compatible combination to
> Documentation/devicetree/bindings/arm/sunxi.yaml.
>
> Cheers,
> Andre
>
> > +
> > + aliases {
> > + serial0 = &uart0;
> > + };
> > +
> > + chosen {
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + reg_vcc5v: vcc5v {
> > + /* board wide 5V supply directly from the DC input */
> > + compatible = "regulator-fixed";
> > + regulator-name = "vcc-5v";
> > + regulator-min-microvolt = <5000000>;
> > + regulator-max-microvolt = <5000000>;
> > + regulator-always-on;
> > + };
> > +};
> > +
> > +&ehci0 {
> > + status = "okay";
> > +};
> > +
> > +&ehci2 {
> > + status = "okay";
> > +};
> > +
> > +&ir {
> > + status = "okay";
> > +};
> > +
> > +&mmc0 {
> > + cd-gpios = <&pio 8 16 GPIO_ACTIVE_LOW>; /* PI16 */
> > + vmmc-supply = <®_dldo1>;
> > + status = "okay";
> > +};
> > +
> > +&mmc2 {
> > + vmmc-supply = <®_dldo1>;
> > + vqmmc-supply = <®_aldo1>;
> > + bus-width = <8>;
> > + non-removable;
> > + cap-mmc-hw-reset;
> > + mmc-ddr-1_8v;
> > + mmc-hs200-1_8v;
> > + status = "okay";
> > +};
> > +
> > +&ohci0 {
> > + status = "okay";
> > +};
> > +
> > +&ohci2 {
> > + status = "okay";
> > +};
> > +
> > +&r_i2c {
> > + status = "okay";
> > +
> > + axp313: pmic at 36 {
> > + compatible = "x-powers,axp313a";
> > + reg = <0x36>;
> > + #interrupt-cells = <1>;
> > + interrupt-controller;
> > + interrupt-parent = <&pio>;
> > + interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */
> > +
> > + vin1-supply = <®_vcc5v>;
> > + vin2-supply = <®_vcc5v>;
> > + vin3-supply = <®_vcc5v>;
> > +
> > + regulators {
> > + /* Supplies VCC-PLL, so needs to be always on. */
> > + reg_aldo1: aldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-name = "vcc1v8";
> > + };
> > +
> > + /* Supplies VCC-IO, so needs to be always on. */
> > + reg_dldo1: dldo1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-name = "vcc3v3";
> > + };
> > +
> > + reg_dcdc1: dcdc1 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <990000>;
> > + regulator-name = "vdd-gpu-sys";
> > + };
> > +
> > + reg_dcdc2: dcdc2 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <810000>;
> > + regulator-max-microvolt = <1100000>;
> > + regulator-name = "vdd-cpu";
> > + };
> > +
> > + reg_dcdc3: dcdc3 {
> > + regulator-always-on;
> > + regulator-min-microvolt = <1360000>;
> > + regulator-max-microvolt = <1360000>;
> > + regulator-name = "vdd-dram";
> > + };
> > + };
> > + };
> > +};
> > +
> > +&pio {
> > + vcc-pc-supply = <®_aldo1>;
> > + vcc-pg-supply = <®_dldo1>;
> > + vcc-ph-supply = <®_dldo1>;
> > + vcc-pi-supply = <®_dldo1>;
> > +};
> > +
> > +&uart0 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&uart0_ph_pins>;
> > + status = "okay";
> > +};
> > +
> > +&usbotg {
> > + dr_mode = "host"; /* USB A type receptable */
> > + status = "okay";
> > +};
> > +
> > +&usbphy {
> > + status = "okay";
> > +};
> > diff --git a/configs/t95_axp313_defconfig b/configs/t95_axp313_defconfig
> > new file mode 100644
> > index 0000000000..6542b5bc88
> > --- /dev/null
> > +++ b/configs/t95_axp313_defconfig
> > @@ -0,0 +1,27 @@
> > +CONFIG_ARM=y
> > +CONFIG_ARCH_SUNXI=y
> > +CONFIG_DEFAULT_DEVICE_TREE="sun50i-h616-t95-axp313"
> > +CONFIG_SPL=y
> > +CONFIG_MACH_SUN50I_H616=y
> > +CONFIG_DRAM_CLK=648
> > +CONFIG_DRAM_SUN50I_H616_ODT_EN=0x1
> > +CONFIG_DRAM_SUN50I_H616_DX_ODT=0x03030303
> > +CONFIG_DRAM_SUN50I_H616_DX_DRI=0x0e0e0e0e
> > +CONFIG_DRAM_SUN50I_H616_CA_DRI=0x1c1c
> > +CONFIG_DRAM_SUN50I_H616_TPR10=0x2f0006
> > +CONFIG_DRAM_SUN50I_H616_TPR11=0xffffdddd
> > +CONFIG_DRAM_SUN50I_H616_TPR12=0xfedf7657
> > +CONFIG_SUNXI_DRAM_H616_DDR3_1333=y
> > +CONFIG_R_I2C_ENABLE=y
> > +CONFIG_SPL_I2C=y
> > +CONFIG_SPL_SYS_I2C_LEGACY=y
> > +CONFIG_SYS_I2C_MVTWSI=y
> > +CONFIG_SYS_I2C_SLAVE=0x7f
> > +CONFIG_SYS_I2C_SPEED=400000
> > +CONFIG_SUPPORT_EMMC_BOOT=y
> > +CONFIG_AXP313_POWER=y
> > +CONFIG_AXP_DCDC3_VOLT=1360
> > +CONFIG_USB_EHCI_HCD=y
> > +CONFIG_USB_OHCI_HCD=y
> > +CONFIG_SUN8I_EMAC=y
> > +CONFIG_SPL_IMAGE_TYPE_SUNXI_TOC0=y
>
--
Kamil Kasperski
More information about the U-Boot
mailing list