[PATCH] configs: imx8mp_beacon: Enable PCIe NVMe drives

[Sumit Garg]

On Wed, 27 Mar 2024 at 02:55, Adam Ford <aford173 at gmail.com> wrote:
>
> The baseboard supports and NVMe drives via the PCIe slot. This
> requires a few extra config options to be enabled.
>
> The NVMe can be enumerated with the following commands:
>
> u-boot=> pci enum
> PCIE-0: Link up (Gen1-x1, Bus0)
> u-boot=> nvme scan
> u-boot=> nvme info
> Device 0: Vendor: 0x15b7 Rev: 20120022 Prod: 184960441105
>             Type: Hard Disk
>             Capacity: 122104.3 MB = 119.2 GB (250069680 x 512)
> u-boot=>
>
> Signed-off-by: Adam Ford <aford173 at gmail.com>

Reviewed-by: Sumit Garg <sumit.garg at linaro.org>

-Sumit

> ---
> Depends on: https://patchwork.ozlabs.org/project/uboot/patch/20240326202439.46707-4-aford173@gmail.com/
>
> diff --git a/configs/imx8mp_beacon_defconfig b/configs/imx8mp_beacon_defconfig
> index 0ae8c9645a..fe1678d8ae 100644
> --- a/configs/imx8mp_beacon_defconfig
> +++ b/configs/imx8mp_beacon_defconfig
> @@ -15,6 +15,7 @@ CONFIG_DM_GPIO=y
>  CONFIG_DEFAULT_DEVICE_TREE="freescale/imx8mp-beacon-kit"
>  CONFIG_SPL_TEXT_BASE=0x920000
>  CONFIG_TARGET_IMX8MP_BEACON=y
> +CONFIG_DM_RESET=y
>  CONFIG_SYS_MONITOR_LEN=524288
>  CONFIG_SPL_MMC=y
>  CONFIG_SPL_SERIAL=y
> @@ -27,6 +28,7 @@ CONFIG_ARMV8_SET_SMPEN=y
>  CONFIG_ARMV8_EA_EL3_FIRST=y
>  CONFIG_SPL_IMX_ROMAPI_LOADADDR=0x48000000
>  CONFIG_SYS_LOAD_ADDR=0x40480000
> +CONFIG_PCI=y
>  # CONFIG_ANDROID_BOOT_IMAGE is not set
>  CONFIG_FIT=y
>  CONFIG_FIT_EXTERNAL_OFFSET=0x3000
> @@ -65,6 +67,7 @@ CONFIG_CMD_FUSE=y
>  CONFIG_CMD_GPIO=y
>  CONFIG_CMD_I2C=y
>  CONFIG_CMD_MMC=y
> +CONFIG_CMD_PCI=y
>  CONFIG_CMD_USB=y
>  CONFIG_CMD_USB_SDP=y
>  CONFIG_CMD_USB_MASS_STORAGE=y
> @@ -118,8 +121,11 @@ CONFIG_DWC_ETH_QOS_IMX=y
>  CONFIG_FEC_MXC=y
>  CONFIG_RGMII=y
>  CONFIG_MII=y
> +CONFIG_NVME_PCI=y
> +CONFIG_PCIE_DW_IMX=y
>  CONFIG_PHY=y
>  CONFIG_PHY_IMX8MQ_USB=y
> +CONFIG_PHY_IMX8M_PCIE=y
>  CONFIG_PINCTRL=y
>  CONFIG_SPL_PINCTRL=y
>  CONFIG_PINCTRL_IMX8M=y
> --
> 2.43.0
>