[PATCH u-boot-mvebu v3 11/18] arm: mvebu: system-controller: Add support for SYSRESET
Stefan Roese
sr at denx.de
Thu Mar 28 11:04:45 CET 2024
On 3/27/24 17:23, Marek Behún wrote:
> Add driver model support for sysreset via mvebu system controller. This is
> currently only available for U-Boot proper.
>
> Signed-off-by: Marek Behún <kabel at kernel.org>
Only a minor comment below. Other than this:
Reviewed-by: Stefan Roese <sr at denx.de>
Thanks,
Stefan
> ---
> arch/arm/mach-mvebu/Kconfig | 18 +++++-
> arch/arm/mach-mvebu/Makefile | 2 +-
> arch/arm/mach-mvebu/cpu.c | 2 +
> arch/arm/mach-mvebu/system-controller.c | 74 +++++++++++++++++++++++--
> 4 files changed, 89 insertions(+), 7 deletions(-)
>
> diff --git a/arch/arm/mach-mvebu/Kconfig b/arch/arm/mach-mvebu/Kconfig
> index 623432a60e..f15d3cc5ed 100644
> --- a/arch/arm/mach-mvebu/Kconfig
> +++ b/arch/arm/mach-mvebu/Kconfig
> @@ -19,6 +19,7 @@ config ARMADA_32BIT
> select SPL_SYS_NO_VECTOR_TABLE if SPL
> select ARCH_VERY_EARLY_INIT
> select ARMADA_32BIT_SYSCON_RESET if DM_RESET && PCI_MVEBU
> + select ARMADA_32BIT_SYSCON_SYSRESET if SYSRESET
>
> # ARMv7 SoCs...
> config ARMADA_375
> @@ -457,16 +458,29 @@ config SF_DEFAULT_MODE
> default 0x0
> depends on MVEBU_SPL_BOOT_DEVICE_SPI
>
> +config ARMADA_32BIT_SYSCON
> + bool
> + depends on ARMADA_32BIT
> + select REGMAP
> + select SYSCON
> +
> config ARMADA_32BIT_SYSCON_RESET
> bool "Support Armada XP/375/38x/39x reset controller"
> depends on ARMADA_32BIT
> depends on DM_RESET
> - select REGMAP
> - select SYSCON
> + select ARMADA_32BIT_SYSCON
> help
> Build support for Armada XP/375/38x/39x reset controller. This is
> needed for PCIe support.
>
> +config ARMADA_32BIT_SYSCON_SYSRESET
> + bool "Support Armada XP/375/38x/39x sysreset via driver model"
> + depends on ARMADA_32BIT
> + depends on SYSRESET
> + select ARMADA_32BIT_SYSCON
> + help
> + Build support for Armada XP/375/38x/39x system reset via driver model.
> +
> source "board/solidrun/clearfog/Kconfig"
> source "board/kobol/helios4/Kconfig"
>
> diff --git a/arch/arm/mach-mvebu/Makefile b/arch/arm/mach-mvebu/Makefile
> index d44ca3a0df..329c2e4915 100644
> --- a/arch/arm/mach-mvebu/Makefile
> +++ b/arch/arm/mach-mvebu/Makefile
> @@ -28,7 +28,7 @@ obj-$(CONFIG_ARMADA_38X) += ../../../drivers/ddr/marvell/a38x/xor.o
> obj-$(CONFIG_ARMADA_XP) += ../../../drivers/ddr/marvell/axp/xor.o
> obj-$(CONFIG_ARMADA_MSYS) += ../../../drivers/ddr/marvell/axp/xor.o
>
> -obj-$(CONFIG_ARMADA_32BIT_SYSCON_RESET) += system-controller.o
> +obj-$(CONFIG_ARMADA_32BIT_SYSCON) += system-controller.o
>
> ifdef CONFIG_ARMADA_38X
> obj-$(CONFIG_MVEBU_EFUSE) += efuse.o
> diff --git a/arch/arm/mach-mvebu/cpu.c b/arch/arm/mach-mvebu/cpu.c
> index 8e0de93538..7c62a5dbb6 100644
> --- a/arch/arm/mach-mvebu/cpu.c
> +++ b/arch/arm/mach-mvebu/cpu.c
> @@ -52,6 +52,7 @@ void lowlevel_init(void)
> */
> }
>
> +#if defined(CONFIG_SPL_BUILD) || !defined(CONFIG_ARMADA_32BIT_SYSCON_SYSRESET)
> void reset_cpu(void)
> {
> struct mvebu_system_registers *reg =
> @@ -62,6 +63,7 @@ void reset_cpu(void)
> while (1)
> ;
> }
> +#endif
>
> u32 get_boot_device(void)
> {
> diff --git a/arch/arm/mach-mvebu/system-controller.c b/arch/arm/mach-mvebu/system-controller.c
> index c5c05922f2..b5f8afb96d 100644
> --- a/arch/arm/mach-mvebu/system-controller.c
> +++ b/arch/arm/mach-mvebu/system-controller.c
> @@ -10,11 +10,24 @@
> #include <regmap.h>
> #include <reset-uclass.h>
> #include <syscon.h>
> +#include <sysreset.h>
> #include <asm/io.h>
>
> -#define MVEBU_SOC_CONTROL_1_REG 0x4
> +#define MVEBU_SOC_CONTROL_1_REG 0x4
>
> -#define MVEBU_PCIE_ID 0
> +#if defined(CONFIG_ARMADA_375)
> +# define MVEBU_RSTOUTN_MASK_REG 0x54
> +# define MVEBU_SYS_SOFT_RST_REG 0x58
> +#else
> +# define MVEBU_RSTOUTN_MASK_REG 0x60
> +# define MVEBU_SYS_SOFT_RST_REG 0x64
> +#endif
> +
> +#define MVEBU_GLOBAL_SOFT_RST_BIT BIT(0)
> +
> +#define MVEBU_PCIE_ID 0
> +
> +#if IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_RESET)
>
> static int mvebu_reset_of_xlate(struct reset_ctl *rst,
> struct ofnode_phandle_args *args)
> @@ -90,11 +103,64 @@ U_BOOT_DRIVER(mvebu_reset) = {
> .ops = &mvebu_reset_ops,
> };
>
> +#endif /* IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_RESET) */
> +
> +#if IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_SYSRESET)
> +
> +static int mvebu_sysreset_request(struct udevice *dev, enum sysreset_t type)
> +{
> + struct regmap *regmap = syscon_get_regmap(dev->parent);
> + uint bit;
> +
> + if (type != SYSRESET_COLD)
> + return -EPROTONOSUPPORT;
> +
> + bit = MVEBU_GLOBAL_SOFT_RST_BIT;
> +
> + regmap_update_bits(regmap, MVEBU_RSTOUTN_MASK_REG, bit, bit);
> + regmap_update_bits(regmap, MVEBU_SYS_SOFT_RST_REG, bit, bit);
> +
> + while (1)
> + ;
A comment before this endless loop might be helpful here.
> +
> + return 0;
> +}
> +
> +static struct sysreset_ops mvebu_sysreset_ops = {
> + .request = mvebu_sysreset_request,
> +};
> +
> +U_BOOT_DRIVER(mvebu_sysreset) = {
> + .name = "mvebu-sysreset",
> + .id = UCLASS_SYSRESET,
> + .ops = &mvebu_sysreset_ops,
> +};
> +
> +#endif /* IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_SYSRESET) */
> +
> static int mvebu_syscon_bind(struct udevice *dev)
> {
> + int ret = 0;
> +
> /* bind also mvebu-reset, with the same ofnode */
> - return device_bind_driver_to_node(dev, "mvebu-reset", "mvebu-reset",
> - dev_ofnode(dev), NULL);
> + if (IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_RESET)) {
> + ret = device_bind_driver_to_node(dev, "mvebu-reset",
> + "mvebu-reset", dev_ofnode(dev),
> + NULL);
> + if (ret < 0)
> + return ret;
> + }
> +
> + /* bind also mvebu-sysreset, with the same ofnode */
> + if (IS_ENABLED(CONFIG_ARMADA_32BIT_SYSCON_SYSRESET)) {
> + ret = device_bind_driver_to_node(dev, "mvebu-sysreset",
> + "mvebu-sysreset",
> + dev_ofnode(dev), NULL);
> + if (ret < 0)
> + return ret;
> + }
> +
> + return ret;
> }
>
> static const struct udevice_id mvebu_syscon_of_match[] = {
Viele Grüße,
Stefan Roese
--
DENX Software Engineering GmbH, Managing Director: Erika Unter
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: (+49)-8142-66989-51 Fax: (+49)-8142-66989-80 Email: sr at denx.de
More information about the U-Boot
mailing list