[PATCH v2 20/22] rockchip: rk3399-pinebook-pro: Sync DT from v6.8 and update defconfig

Jonas Karlman jonas at kwiboo.se
Wed May 1 18:22:37 CEST 2024


Sync rk3399-pinebook-pro device tree from Linux kernel v6.8.

Add SF_DEFAULT_SPEED=10000000 and SPI_FLASH_SFDP_SUPPORT=y to improve
support for booting from SPI flash.

Add CMD_POWEROFF=y to support poweroff using cmdline and power on using
the pwr button on the board.

Remove SPL_TINY_MEMSET=y to use full memset in SPL.

Signed-off-by: Jonas Karlman <jonas at kwiboo.se>
Reviewed-by: Dragan Simic <dsimic at manjaro.org>
Reviewed-by: Kever Yang <kever.yang at rock-chips.com>
---
v2: Collect r-b tags
---
 arch/arm/dts/rk3399-pinebook-pro.dts  | 24 +++++++-----------------
 configs/pinebook-pro-rk3399_defconfig |  6 ++++--
 2 files changed, 11 insertions(+), 19 deletions(-)

diff --git a/arch/arm/dts/rk3399-pinebook-pro.dts b/arch/arm/dts/rk3399-pinebook-pro.dts
index d6b68d77d63a..054c6a4d1a45 100644
--- a/arch/arm/dts/rk3399-pinebook-pro.dts
+++ b/arch/arm/dts/rk3399-pinebook-pro.dts
@@ -50,19 +50,9 @@
 		pinctrl-0 = <&panel_en_pin>;
 		power-supply = <&vcc3v3_panel>;
 
-		ports {
-			#address-cells = <1>;
-			#size-cells = <0>;
-
-			port at 0 {
-				reg = <0>;
-				#address-cells = <1>;
-				#size-cells = <0>;
-
-				panel_in_edp: endpoint at 0 {
-					reg = <0>;
-					remote-endpoint = <&edp_out_panel>;
-				};
+		port {
+			panel_in_edp: endpoint {
+				remote-endpoint = <&edp_out_panel>;
 			};
 		};
 	};
@@ -76,7 +66,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&lidbtn_pin>;
 
-		lid {
+		switch-lid {
 			debounce-interval = <20>;
 			gpios = <&gpio1 RK_PA1 GPIO_ACTIVE_LOW>;
 			label = "Lid";
@@ -92,7 +82,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pwrbtn_pin>;
 
-		power {
+		key-power {
 			debounce-interval = <20>;
 			gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
 			label = "Power";
@@ -675,7 +665,7 @@
 	i2c-scl-rising-time-ns = <168>;
 	status = "okay";
 
-	es8316: es8316 at 11 {
+	es8316: audio-codec at 11 {
 		compatible = "everest,es8316";
 		reg = <0x11>;
 		clocks = <&cru SCLK_I2S_8CH_OUT>;
@@ -943,7 +933,7 @@
 	disable-wp;
 	pinctrl-names = "default";
 	pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
-	sd-uhs-sdr104;
+	sd-uhs-sdr50;
 	vmmc-supply = <&vcc3v0_sd>;
 	vqmmc-supply = <&vcc_sdio>;
 	status = "okay";
diff --git a/configs/pinebook-pro-rk3399_defconfig b/configs/pinebook-pro-rk3399_defconfig
index dd8bc2b72cc3..8ac6ddd49dea 100644
--- a/configs/pinebook-pro-rk3399_defconfig
+++ b/configs/pinebook-pro-rk3399_defconfig
@@ -4,7 +4,7 @@ CONFIG_COUNTER_FREQUENCY=24000000
 CONFIG_ARCH_ROCKCHIP=y
 CONFIG_SPL_GPIO=y
 CONFIG_NR_DRAM_BANKS=1
-CONFIG_SF_DEFAULT_SPEED=20000000
+CONFIG_SF_DEFAULT_SPEED=10000000
 CONFIG_ENV_SIZE=0x8000
 CONFIG_ENV_OFFSET=0x3F8000
 CONFIG_DEFAULT_DEVICE_TREE="rk3399-pinebook-pro"
@@ -36,6 +36,7 @@ CONFIG_CMD_GPT=y
 CONFIG_CMD_I2C=y
 CONFIG_CMD_MMC=y
 CONFIG_CMD_PCI=y
+CONFIG_CMD_POWEROFF=y
 CONFIG_CMD_USB=y
 # CONFIG_CMD_SETEXPR is not set
 CONFIG_CMD_TIME=y
@@ -64,7 +65,9 @@ CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_SDMA=y
 CONFIG_MMC_SDHCI_ROCKCHIP=y
 CONFIG_SF_DEFAULT_BUS=1
+CONFIG_SPI_FLASH_SFDP_SUPPORT=y
 CONFIG_SPI_FLASH_GIGADEVICE=y
+CONFIG_SPI_FLASH_SILICONKAISER=y
 CONFIG_SPI_FLASH_WINBOND=y
 CONFIG_NVME_PCI=y
 CONFIG_PHY_ROCKCHIP_INNO_USB2=y
@@ -98,5 +101,4 @@ CONFIG_VIDEO=y
 CONFIG_DISPLAY=y
 CONFIG_VIDEO_ROCKCHIP=y
 CONFIG_DISPLAY_ROCKCHIP_EDP=y
-CONFIG_SPL_TINY_MEMSET=y
 CONFIG_ERRNO_STR=y
-- 
2.43.2



More information about the U-Boot mailing list