[PATCH 06/11] net: Add support for ADI SC5xx SoCs with DWC QoS ethernet
Greg Malysa
greg.malysa at timesys.com
Wed May 15 23:57:43 CEST 2024
The ADI SC598 includes a Designware QoS 5.20a IP block. This
commit adds support for using the existing ethernet QoS driver
with the SC598 SoC.
Co-developed-by: Ian Roberts <ian.roberts at timesys.com>
Signed-off-by: Ian Roberts <ian.roberts at timesys.com>
Co-developed-by: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
Signed-off-by: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
Signed-off-by: Vasileios Bimpikas <vasileios.bimpikas at analog.com>
Signed-off-by: Utsav Agarwal <utsav.agarwal at analog.com>
Signed-off-by: Arturs Artamonovs <arturs.artamonovs at analog.com>
Signed-off-by: Greg Malysa <greg.malysa at timesys.com>
---
MAINTAINERS | 1 +
drivers/net/Kconfig | 7 +++
drivers/net/Makefile | 1 +
drivers/net/dwc_eth_qos.c | 6 ++
drivers/net/dwc_eth_qos.h | 2 +
drivers/net/dwc_eth_qos_adi.c | 101 ++++++++++++++++++++++++++++++++++
6 files changed, 118 insertions(+)
create mode 100644 drivers/net/dwc_eth_qos_adi.c
diff --git a/MAINTAINERS b/MAINTAINERS
index 977233451e..c1685f0352 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -613,6 +613,7 @@ F: drivers/clk/adi/
F: drivers/gpio/adp5588_gpio.c
F: drivers/gpio/gpio-adi-adsp.c
F: drivers/i2c/adi_i2c.c
+F: drivers/net/dwc_eth_qos_adi.c
F: drivers/pinctrl/pinctrl-adi-adsp.c
F: drivers/serial/serial_adi_uart4.c
F: drivers/timer/adi_sc5xx_timer.c
diff --git a/drivers/net/Kconfig b/drivers/net/Kconfig
index b4ff033afa..9ae471e371 100644
--- a/drivers/net/Kconfig
+++ b/drivers/net/Kconfig
@@ -236,6 +236,13 @@ config DWC_ETH_QOS
Of Service) IP block. The IP supports many options for bus type,
clocking/reset structure, and feature list.
+config DWC_ETH_QOS_ADI
+ bool "Synopsys DWC Ethernet QOS device support for ADI SC59x-64 parts"
+ depends on DWC_ETH_QOS
+ help
+ The Synopsis Designware Ethernet QoS IP block with the specific
+ configuration used in the ADI ADSP-SC59X 64 bit SoCs
+
config DWC_ETH_QOS_IMX
bool "Synopsys DWC Ethernet QOS device support for IMX"
depends on DWC_ETH_QOS
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index dce71685c3..612f5644f3 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_DM_ETH_PHY) += eth-phy-uclass.o
obj-$(CONFIG_DRIVER_DM9000) += dm9000x.o
obj-$(CONFIG_DSA_SANDBOX) += dsa_sandbox.o
obj-$(CONFIG_DWC_ETH_QOS) += dwc_eth_qos.o
+obj-$(CONFIG_DWC_ETH_QOS_ADI) += dwc_eth_qos_adi.o
obj-$(CONFIG_DWC_ETH_QOS_IMX) += dwc_eth_qos_imx.o
obj-$(CONFIG_DWC_ETH_QOS_ROCKCHIP) += dwc_eth_qos_rockchip.o
obj-$(CONFIG_DWC_ETH_QOS_QCOM) += dwc_eth_qos_qcom.o
diff --git a/drivers/net/dwc_eth_qos.c b/drivers/net/dwc_eth_qos.c
index 67ac86f82b..10528368ca 100644
--- a/drivers/net/dwc_eth_qos.c
+++ b/drivers/net/dwc_eth_qos.c
@@ -1544,6 +1544,12 @@ static const struct udevice_id eqos_ids[] = {
.compatible = "starfive,jh7110-dwmac",
.data = (ulong)&eqos_jh7110_config
},
+#endif
+#if IS_ENABLED(CONFIG_DWC_ETH_QOS_ADI)
+ {
+ .compatible = "adi,sc59x-dwmac-eqos",
+ .data = (ulong)&eqos_adi_config
+ },
#endif
{ }
};
diff --git a/drivers/net/dwc_eth_qos.h b/drivers/net/dwc_eth_qos.h
index 8b3d0d464d..1b28f2a056 100644
--- a/drivers/net/dwc_eth_qos.h
+++ b/drivers/net/dwc_eth_qos.h
@@ -84,6 +84,7 @@ struct eqos_mac_regs {
#define EQOS_MAC_MDIO_ADDRESS_CR_SHIFT 8
#define EQOS_MAC_MDIO_ADDRESS_CR_100_150 1
#define EQOS_MAC_MDIO_ADDRESS_CR_20_35 2
+#define EQOS_MAC_MDIO_ADDRESS_CR_150_250 4
#define EQOS_MAC_MDIO_ADDRESS_CR_250_300 5
#define EQOS_MAC_MDIO_ADDRESS_SKAP BIT(4)
#define EQOS_MAC_MDIO_ADDRESS_GOC_SHIFT 2
@@ -293,3 +294,4 @@ extern struct eqos_config eqos_qcom_config;
extern struct eqos_config eqos_stm32mp13_config;
extern struct eqos_config eqos_stm32mp15_config;
extern struct eqos_config eqos_jh7110_config;
+extern struct eqos_config eqos_adi_config;
diff --git a/drivers/net/dwc_eth_qos_adi.c b/drivers/net/dwc_eth_qos_adi.c
new file mode 100644
index 0000000000..8e770c0dcb
--- /dev/null
+++ b/drivers/net/dwc_eth_qos_adi.c
@@ -0,0 +1,101 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * (C) Copyright 2024 - Analog Devices, Inc.
+ *
+ * Written and/or maintained by Timesys Corporation
+ *
+ * Author: Greg Malysa <greg.malysa at timesys.com>
+ * Additional Contact: Nathan Barrett-Morrison <nathan.morrison at timesys.com>
+ */
+
+#include <clk.h>
+#include <dm.h>
+#include <net.h>
+#include <phy.h>
+#include <reset.h>
+#include <asm/io.h>
+
+#include <asm/arch-adi/sc5xx/sc5xx.h>
+
+#include "dwc_eth_qos.h"
+
+static int eqos_start_resets_adi(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+ u32 val;
+
+ /*
+ * Settings need to latch with the DMA reset below. Currently only
+ * rgmii is supported but other phy interfaces may be supported in
+ * the future
+ */
+ sc5xx_enable_rgmii();
+
+ val = readl(&eqos->dma_regs->mode);
+ val |= EQOS_DMA_MODE_SWR;
+ writel(val, &eqos->dma_regs->mode);
+
+ return 0;
+}
+
+static int eqos_probe_resources_adi(struct udevice *dev)
+{
+ struct eqos_priv *eqos = dev_get_priv(dev);
+ phy_interface_t interface;
+
+ interface = eqos->config->interface(dev);
+ if (interface == PHY_INTERFACE_MODE_NA) {
+ pr_err("Invalid PHY interface\n");
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+/**
+ * rgmii tx clock rate is set to 125 MHz regardless of phy mode, and
+ * by default the internal clock is always connected to 125 MHz. According
+ * to the HRM it is invalid for this clock to have any other speed, so
+ * the hardware won't work anyway if this is wrong.
+ */
+static ulong eqos_get_tick_clk_rate_adi(struct udevice *dev)
+{
+ return 125 * 1000000;
+}
+
+static int eqos_get_enetaddr_adi(struct udevice *dev)
+{
+ struct eth_pdata *pdata = dev_get_plat(dev);
+ return eth_env_get_enetaddr("ethaddr", pdata->enetaddr);
+}
+
+static struct eqos_ops eqos_adi_ops = {
+ .eqos_inval_desc = eqos_inval_desc_generic,
+ .eqos_flush_desc = eqos_flush_desc_generic,
+ .eqos_inval_buffer = eqos_inval_buffer_generic,
+ .eqos_flush_buffer = eqos_flush_buffer_generic,
+ .eqos_probe_resources = eqos_probe_resources_adi,
+ .eqos_remove_resources = eqos_null_ops,
+ .eqos_start_resets = eqos_start_resets_adi,
+ .eqos_stop_resets = eqos_null_ops,
+ .eqos_start_clks = eqos_null_ops,
+ .eqos_stop_clks = eqos_null_ops,
+ .eqos_calibrate_pads = eqos_null_ops,
+ .eqos_disable_calibration = eqos_null_ops,
+ .eqos_set_tx_clk_speed = eqos_null_ops,
+ .eqos_get_enetaddr = eqos_get_enetaddr_adi,
+ .eqos_get_tick_clk_rate = eqos_get_tick_clk_rate_adi,
+};
+
+// @todo read mdio_wait from device tree
+// @todo read swr_wait from device tree
+struct eqos_config __maybe_unused eqos_adi_config = {
+ .reg_access_always_ok = true,
+ .mdio_wait = 20,
+ .swr_wait = 50,
+ .config_mac = EQOS_MAC_RXQ_CTRL0_RXQ0EN_ENABLED_DCB,
+ .config_mac_mdio = EQOS_MAC_MDIO_ADDRESS_CR_150_250,
+ .axi_bus_width = EQOS_AXI_WIDTH_32,
+ .interface = dev_read_phy_mode,
+ .ops = &eqos_adi_ops,
+};
--
2.43.2
More information about the U-Boot
mailing list