[PATCH] ARM: dts: renesas: Remove leftovers after OF_UPSTREAM conversion
Adam Ford
aford173 at gmail.com
Mon May 20 17:19:06 CEST 2024
On Sun, May 19, 2024 at 3:40 PM Marek Vasut
<marek.vasut+renesas at mailbox.org> wrote:
>
> Remove leftover DTSI files after OF_UPSTREAM conversion.
> Those are no longer used and no longer necessary, remove them.
> No functional change.
>
This seems like the right thing to do.
> Signed-off-by: Marek Vasut <marek.vasut+renesas at mailbox.org>
Acked-by: Adam Ford <aford173 at gmail.com>
> ---
> Cc: Adam Ford <aford173 at gmail.com>
> Cc: Tom Rini <trini at konsulko.com>
> ---
> arch/arm/dts/salvator-common.dtsi | 1104 ----------------------
> arch/arm/dts/salvator-x.dtsi | 29 -
> arch/arm/dts/salvator-xs.dtsi | 85 --
> arch/arm/dts/ulcb-audio-graph-card.dtsi | 85 --
> arch/arm/dts/ulcb-audio-graph-card2.dtsi | 26 -
> arch/arm/dts/ulcb.dtsi | 509 ----------
> 6 files changed, 1838 deletions(-)
> delete mode 100644 arch/arm/dts/salvator-common.dtsi
> delete mode 100644 arch/arm/dts/salvator-x.dtsi
> delete mode 100644 arch/arm/dts/salvator-xs.dtsi
> delete mode 100644 arch/arm/dts/ulcb-audio-graph-card.dtsi
> delete mode 100644 arch/arm/dts/ulcb-audio-graph-card2.dtsi
> delete mode 100644 arch/arm/dts/ulcb.dtsi
>
> diff --git a/arch/arm/dts/salvator-common.dtsi b/arch/arm/dts/salvator-common.dtsi
> deleted file mode 100644
> index 4a3d5037821..00000000000
> --- a/arch/arm/dts/salvator-common.dtsi
> +++ /dev/null
> @@ -1,1104 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree Source for common parts of Salvator-X board variants
> - *
> - * Copyright (C) 2015-2016 Renesas Electronics Corp.
> - */
> -
> -/*
> - * SSI-AK4613
> - *
> - * This command is required when Playback/Capture
> - *
> - * amixer set "DVC Out" 100%
> - * amixer set "DVC In" 100%
> - *
> - * You can use Mute
> - *
> - * amixer set "DVC Out Mute" on
> - * amixer set "DVC In Mute" on
> - *
> - * You can use Volume Ramp
> - *
> - * amixer set "DVC Out Ramp Up Rate" "0.125 dB/64 steps"
> - * amixer set "DVC Out Ramp Down Rate" "0.125 dB/512 steps"
> - * amixer set "DVC Out Ramp" on
> - * aplay xxx.wav &
> - * amixer set "DVC Out" 80% // Volume Down
> - * amixer set "DVC Out" 100% // Volume Up
> - */
> -
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/input/input.h>
> -
> -/ {
> - aliases {
> - i2c0 = &i2c0;
> - i2c1 = &i2c1;
> - i2c2 = &i2c2;
> - i2c3 = &i2c3;
> - i2c4 = &i2c4;
> - i2c5 = &i2c5;
> - i2c6 = &i2c6;
> - i2c7 = &i2c_dvfs;
> - serial0 = &scif2;
> - serial1 = &hscif1;
> - ethernet0 = &avb;
> - mmc0 = &sdhi2;
> - mmc1 = &sdhi0;
> - mmc2 = &sdhi3;
> - };
> -
> - chosen {
> - bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
> - stdout-path = "serial0:115200n8";
> - };
> -
> - audio_clkout: audio-clkout {
> - /*
> - * This is same as <&rcar_sound 0>
> - * but needed to avoid cs2000/rcar_sound probe dead-lock
> - */
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <12288000>;
> - };
> -
> - backlight: backlight {
> - compatible = "pwm-backlight";
> - pwms = <&pwm1 0 50000>;
> -
> - brightness-levels = <256 128 64 16 8 4 0>;
> - default-brightness-level = <6>;
> -
> - power-supply = <®_12v>;
> - enable-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
> - };
> -
> - cvbs-in {
> - compatible = "composite-video-connector";
> - label = "CVBS IN";
> -
> - port {
> - cvbs_con: endpoint {
> - remote-endpoint = <&adv7482_ain7>;
> - };
> - };
> - };
> -
> - hdmi-in {
> - compatible = "hdmi-connector";
> - label = "HDMI IN";
> - type = "a";
> -
> - port {
> - hdmi_in_con: endpoint {
> - remote-endpoint = <&adv7482_hdmi>;
> - };
> - };
> - };
> -
> - hdmi0-out {
> - compatible = "hdmi-connector";
> - label = "HDMI0 OUT";
> - type = "a";
> -
> - port {
> - hdmi0_con: endpoint {
> - remote-endpoint = <&rcar_dw_hdmi0_out>;
> - };
> - };
> - };
> -
> - hdmi1-out {
> - compatible = "hdmi-connector";
> - label = "HDMI1 OUT";
> - type = "a";
> -
> - port {
> - hdmi1_con: endpoint {
> - };
> - };
> - };
> -
> - keys {
> - compatible = "gpio-keys";
> -
> - pinctrl-0 = <&keys_pins>;
> - pinctrl-names = "default";
> -
> - key-1 {
> - gpios = <&gpio5 17 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_1>;
> - label = "SW4-1";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-2 {
> - gpios = <&gpio5 20 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_2>;
> - label = "SW4-2";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-3 {
> - gpios = <&gpio5 22 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_3>;
> - label = "SW4-3";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-4 {
> - gpios = <&gpio5 23 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_4>;
> - label = "SW4-4";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-a {
> - gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_A>;
> - label = "TSW0";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-b {
> - gpios = <&gpio6 12 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_B>;
> - label = "TSW1";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - key-c {
> - gpios = <&gpio6 13 GPIO_ACTIVE_LOW>;
> - linux,code = <KEY_C>;
> - label = "TSW2";
> - wakeup-source;
> - debounce-interval = <20>;
> - };
> - };
> -
> - reg_1p8v: regulator-1p8v {
> - compatible = "regulator-fixed";
> - regulator-name = "fixed-1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - reg_3p3v: regulator-3p3v {
> - compatible = "regulator-fixed";
> - regulator-name = "fixed-3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - reg_12v: regulator-12v {
> - compatible = "regulator-fixed";
> - regulator-name = "fixed-12V";
> - regulator-min-microvolt = <12000000>;
> - regulator-max-microvolt = <12000000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - sound_card: sound {
> - compatible = "audio-graph-card";
> -
> - label = "rcar-sound";
> -
> - dais = <&rsnd_port0 /* ak4613 */
> - &rsnd_port1 /* HDMI0 */
> -#ifdef SOC_HAS_HDMI1
> - &rsnd_port2 /* HDMI1 */
> -#endif
> - >;
> - };
> -
> - vbus0_usb2: regulator-vbus0-usb2 {
> - compatible = "regulator-fixed";
> -
> - regulator-name = "USB20_VBUS0";
> - regulator-min-microvolt = <5000000>;
> - regulator-max-microvolt = <5000000>;
> -
> - gpio = <&gpio6 16 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - vcc_sdhi0: regulator-vcc-sdhi0 {
> - compatible = "regulator-fixed";
> -
> - regulator-name = "SDHI0 Vcc";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - vccq_sdhi0: regulator-vccq-sdhi0 {
> - compatible = "regulator-gpio";
> -
> - regulator-name = "SDHI0 VccQ";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
> - gpios-states = <1>;
> - states = <3300000 1>, <1800000 0>;
> - };
> -
> - vcc_sdhi3: regulator-vcc-sdhi3 {
> - compatible = "regulator-fixed";
> -
> - regulator-name = "SDHI3 Vcc";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - vccq_sdhi3: regulator-vccq-sdhi3 {
> - compatible = "regulator-gpio";
> -
> - regulator-name = "SDHI3 VccQ";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
> - gpios-states = <1>;
> - states = <3300000 1>, <1800000 0>;
> - };
> -
> - vga {
> - compatible = "vga-connector";
> -
> - port {
> - vga_in: endpoint {
> - remote-endpoint = <&adv7123_out>;
> - };
> - };
> - };
> -
> - vga-encoder {
> - compatible = "adi,adv7123";
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port at 0 {
> - reg = <0>;
> - adv7123_in: endpoint {
> - remote-endpoint = <&du_out_rgb>;
> - };
> - };
> - port at 1 {
> - reg = <1>;
> - adv7123_out: endpoint {
> - remote-endpoint = <&vga_in>;
> - };
> - };
> - };
> - };
> -
> - x12_clk: x12 {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <24576000>;
> - };
> -
> - /* External DU dot clocks */
> - x21_clk: x21-clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <33000000>;
> - };
> -
> - x22_clk: x22-clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <33000000>;
> - };
> -
> - x23_clk: x23-clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <25000000>;
> - };
> -};
> -
> -&a57_0 {
> - cpu-supply = <&dvfs>;
> -};
> -
> -&audio_clk_a {
> - clock-frequency = <22579200>;
> -};
> -
> -&avb {
> - pinctrl-0 = <&avb_pins>;
> - pinctrl-names = "default";
> - phy-handle = <&phy0>;
> - tx-internal-delay-ps = <2000>;
> - status = "okay";
> -
> - phy0: ethernet-phy at 0 {
> - compatible = "ethernet-phy-id0022.1622",
> - "ethernet-phy-ieee802.3-c22";
> - rxc-skew-ps = <1500>;
> - reg = <0>;
> - interrupt-parent = <&gpio2>;
> - interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
> - };
> -};
> -
> -&csi20 {
> - status = "okay";
> -
> - ports {
> - port at 0 {
> - csi20_in: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <1>;
> - remote-endpoint = <&adv7482_txb>;
> - };
> - };
> - };
> -};
> -
> -&csi40 {
> - status = "okay";
> -
> - ports {
> - port at 0 {
> - csi40_in: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <1 2 3 4>;
> - remote-endpoint = <&adv7482_txa>;
> - };
> - };
> - };
> -};
> -
> -&du {
> - pinctrl-0 = <&du_pins>;
> - pinctrl-names = "default";
> - status = "okay";
> -
> - ports {
> - port at 0 {
> - du_out_rgb: endpoint {
> - remote-endpoint = <&adv7123_in>;
> - };
> - };
> - };
> -};
> -
> -&ehci0 {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&ehci1 {
> - status = "okay";
> -};
> -
> -&extalr_clk {
> - clock-frequency = <32768>;
> -};
> -
> -&hdmi0 {
> - status = "okay";
> -
> - ports {
> - port at 1 {
> - reg = <1>;
> - rcar_dw_hdmi0_out: endpoint {
> - remote-endpoint = <&hdmi0_con>;
> - };
> - };
> - port at 2 {
> - reg = <2>;
> - dw_hdmi0_snd_in: endpoint {
> - remote-endpoint = <&rsnd_endpoint1>;
> - };
> - };
> - };
> -};
> -
> -#ifdef SOC_HAS_HDMI1
> -&hdmi1 {
> - status = "okay";
> -
> - ports {
> - port at 1 {
> - reg = <1>;
> - rcar_dw_hdmi1_out: endpoint {
> - remote-endpoint = <&hdmi1_con>;
> - };
> - };
> - port at 2 {
> - reg = <2>;
> - dw_hdmi1_snd_in: endpoint {
> - remote-endpoint = <&rsnd_endpoint2>;
> - };
> - };
> - };
> -};
> -
> -&hdmi1_con {
> - remote-endpoint = <&rcar_dw_hdmi1_out>;
> -};
> -#endif /* SOC_HAS_HDMI1 */
> -
> -&hscif1 {
> - pinctrl-0 = <&hscif1_pins>;
> - pinctrl-names = "default";
> -
> - uart-has-rtscts;
> - /* Please only enable hscif1 or scif1 */
> - status = "okay";
> -};
> -
> -&hsusb {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&i2c2 {
> - pinctrl-0 = <&i2c2_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -
> - clock-frequency = <100000>;
> -
> - ak4613: codec at 10 {
> - compatible = "asahi-kasei,ak4613";
> - #sound-dai-cells = <0>;
> - reg = <0x10>;
> - clocks = <&rcar_sound 3>;
> -
> - asahi-kasei,in1-single-end;
> - asahi-kasei,in2-single-end;
> - asahi-kasei,out1-single-end;
> - asahi-kasei,out2-single-end;
> - asahi-kasei,out3-single-end;
> - asahi-kasei,out4-single-end;
> - asahi-kasei,out5-single-end;
> - asahi-kasei,out6-single-end;
> -
> - port {
> - ak4613_endpoint: endpoint {
> - remote-endpoint = <&rsnd_endpoint0>;
> - };
> - };
> - };
> -
> - cs2000: clk_multiplier at 4f {
> - #clock-cells = <0>;
> - compatible = "cirrus,cs2000-cp";
> - reg = <0x4f>;
> - clocks = <&audio_clkout>, <&x12_clk>;
> - clock-names = "clk_in", "ref_clk";
> -
> - assigned-clocks = <&cs2000>;
> - assigned-clock-rates = <24576000>; /* 1/1 divide */
> - };
> -};
> -
> -&i2c4 {
> - status = "okay";
> -
> - pca9654: gpio at 20 {
> - compatible = "onnn,pca9654";
> - reg = <0x20>;
> - gpio-controller;
> - #gpio-cells = <2>;
> - };
> -
> - video-receiver at 70 {
> - compatible = "adi,adv7482";
> - reg = <0x70 0x71 0x72 0x73 0x74 0x75
> - 0x60 0x61 0x62 0x63 0x64 0x65>;
> - reg-names = "main", "dpll", "cp", "hdmi", "edid", "repeater",
> - "infoframe", "cbus", "cec", "sdp", "txa", "txb" ;
> -
> - interrupt-parent = <&gpio6>;
> - interrupt-names = "intrq1", "intrq2";
> - interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
> - <31 IRQ_TYPE_LEVEL_LOW>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> -
> - port at 7 {
> - reg = <7>;
> -
> - adv7482_ain7: endpoint {
> - remote-endpoint = <&cvbs_con>;
> - };
> - };
> -
> - port at 8 {
> - reg = <8>;
> -
> - adv7482_hdmi: endpoint {
> - remote-endpoint = <&hdmi_in_con>;
> - };
> - };
> -
> - port at a {
> - reg = <10>;
> -
> - adv7482_txa: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <1 2 3 4>;
> - remote-endpoint = <&csi40_in>;
> - };
> - };
> -
> - port at b {
> - reg = <11>;
> -
> - adv7482_txb: endpoint {
> - clock-lanes = <0>;
> - data-lanes = <1>;
> - remote-endpoint = <&csi20_in>;
> - };
> - };
> - };
> - };
> -
> - csa_vdd: adc at 7c {
> - compatible = "maxim,max9611";
> - reg = <0x7c>;
> -
> - shunt-resistor-micro-ohms = <5000>;
> - };
> -
> - csa_dvfs: adc at 7f {
> - compatible = "maxim,max9611";
> - reg = <0x7f>;
> -
> - shunt-resistor-micro-ohms = <5000>;
> - };
> -};
> -
> -&i2c_dvfs {
> - status = "okay";
> -
> - clock-frequency = <400000>;
> -
> - pmic: pmic at 30 {
> - pinctrl-0 = <&irq0_pins>;
> - pinctrl-names = "default";
> -
> - compatible = "rohm,bd9571mwv";
> - reg = <0x30>;
> - interrupt-parent = <&intc_ex>;
> - interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - gpio-controller;
> - #gpio-cells = <2>;
> - rohm,ddr-backup-power = <0xf>;
> - rohm,rstbmode-level;
> -
> - regulators {
> - dvfs: dvfs {
> - regulator-name = "dvfs";
> - regulator-min-microvolt = <750000>;
> - regulator-max-microvolt = <1030000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> - };
> - };
> -
> - eeprom at 50 {
> - compatible = "rohm,br24t01", "atmel,24c01";
> - reg = <0x50>;
> - pagesize = <8>;
> - };
> -};
> -
> -&ohci0 {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&ohci1 {
> - status = "okay";
> -};
> -
> -&pcie_bus_clk {
> - clock-frequency = <100000000>;
> -};
> -
> -&pciec0 {
> - status = "okay";
> -};
> -
> -&pciec1 {
> - status = "okay";
> -};
> -
> -&pfc {
> - pinctrl-0 = <&scif_clk_pins>;
> - pinctrl-names = "default";
> -
> - avb_pins: avb {
> - mux {
> - groups = "avb_link", "avb_mdio", "avb_mii";
> - function = "avb";
> - };
> -
> - pins_mdio {
> - groups = "avb_mdio";
> - drive-strength = <24>;
> - };
> -
> - pins_mii_tx {
> - pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
> - "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
> - drive-strength = <12>;
> - };
> - };
> -
> - du_pins: du {
> - groups = "du_rgb888", "du_sync", "du_oddf", "du_clk_out_0";
> - function = "du";
> - };
> -
> - hscif1_pins: hscif1 {
> - groups = "hscif1_data_a", "hscif1_ctrl_a";
> - function = "hscif1";
> - };
> -
> - i2c2_pins: i2c2 {
> - groups = "i2c2_a";
> - function = "i2c2";
> - };
> -
> - irq0_pins: irq0 {
> - groups = "intc_ex_irq0";
> - function = "intc_ex";
> - };
> -
> - keys_pins: keys {
> - pins = "GP_5_17", "GP_5_20", "GP_5_22";
> - bias-pull-up;
> - };
> -
> - pwm1_pins: pwm1 {
> - groups = "pwm1_a";
> - function = "pwm1";
> - };
> -
> - scif1_pins: scif1 {
> - groups = "scif1_data_a", "scif1_ctrl";
> - function = "scif1";
> - };
> -
> - scif2_pins: scif2 {
> - groups = "scif2_data_a";
> - function = "scif2";
> - };
> -
> - scif_clk_pins: scif_clk {
> - groups = "scif_clk_a";
> - function = "scif_clk";
> - };
> -
> - sdhi0_pins: sd0 {
> - groups = "sdhi0_data4", "sdhi0_ctrl";
> - function = "sdhi0";
> - power-source = <3300>;
> - };
> -
> - sdhi0_pins_uhs: sd0_uhs {
> - groups = "sdhi0_data4", "sdhi0_ctrl";
> - function = "sdhi0";
> - power-source = <1800>;
> - };
> -
> - sdhi2_pins: sd2 {
> - groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
> - function = "sdhi2";
> - power-source = <1800>;
> - };
> -
> - sdhi3_pins: sd3 {
> - groups = "sdhi3_data4", "sdhi3_ctrl";
> - function = "sdhi3";
> - power-source = <3300>;
> - };
> -
> - sdhi3_pins_uhs: sd3_uhs {
> - groups = "sdhi3_data4", "sdhi3_ctrl";
> - function = "sdhi3";
> - power-source = <1800>;
> - };
> -
> - sound_pins: sound {
> - groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
> - function = "ssi";
> - };
> -
> - sound_clk_pins: sound_clk {
> - groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
> - "audio_clkout_a", "audio_clkout3_a";
> - function = "audio_clk";
> - };
> -
> - usb0_pins: usb0 {
> - groups = "usb0";
> - function = "usb0";
> - };
> -
> - usb1_pins: usb1 {
> - mux {
> - groups = "usb1";
> - function = "usb1";
> - };
> -
> - ovc {
> - pins = "GP_6_27";
> - bias-pull-up;
> - };
> -
> - pwen {
> - pins = "GP_6_26";
> - bias-pull-down;
> - };
> - };
> -
> - usb30_pins: usb30 {
> - groups = "usb30";
> - function = "usb30";
> - };
> -};
> -
> -&pwm1 {
> - pinctrl-0 = <&pwm1_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -&rcar_sound {
> - pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
> - pinctrl-names = "default";
> -
> - /* audio_clkout0/1/2/3 */
> - #clock-cells = <1>;
> - clock-frequency = <12288000 11289600>;
> -
> - status = "okay";
> -
> - /* update <audio_clk_b> to <cs2000> */
> - clocks = <&cpg CPG_MOD 1005>,
> - <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
> - <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
> - <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
> - <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
> - <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
> - <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
> - <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
> - <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
> - <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
> - <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
> - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
> - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
> - <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
> - <&audio_clk_a>, <&cs2000>,
> - <&audio_clk_c>,
> - <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
> -
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - rsnd_port0: port at 0 {
> - reg = <0>;
> - rsnd_endpoint0: endpoint {
> - remote-endpoint = <&ak4613_endpoint>;
> -
> - dai-format = "left_j";
> - bitclock-master = <&rsnd_endpoint0>;
> - frame-master = <&rsnd_endpoint0>;
> -
> - playback = <&ssi0>, <&src0>, <&dvc0>;
> - capture = <&ssi1>, <&src1>, <&dvc1>;
> - };
> - };
> -
> - rsnd_port1: port at 1 {
> - reg = <1>;
> - rsnd_endpoint1: endpoint {
> - remote-endpoint = <&dw_hdmi0_snd_in>;
> -
> - dai-format = "i2s";
> - bitclock-master = <&rsnd_endpoint1>;
> - frame-master = <&rsnd_endpoint1>;
> -
> - playback = <&ssi2>;
> - };
> - };
> -
> -#ifdef SOC_HAS_HDMI1
> - rsnd_port2: port at 2 {
> - reg = <2>;
> - rsnd_endpoint2: endpoint {
> - remote-endpoint = <&dw_hdmi1_snd_in>;
> -
> - dai-format = "i2s";
> - bitclock-master = <&rsnd_endpoint2>;
> - frame-master = <&rsnd_endpoint2>;
> -
> - playback = <&ssi3>;
> - };
> - };
> -#endif /* SOC_HAS_HDMI1 */
> - };
> -};
> -
> -&rpc {
> - /* Left disabled. To be enabled by firmware when unlocked. */
> -
> - flash at 0 {
> - compatible = "cypress,hyperflash", "cfi-flash";
> - reg = <0>;
> -
> - partitions {
> - compatible = "fixed-partitions";
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - bootparam at 0 {
> - reg = <0x00000000 0x040000>;
> - read-only;
> - };
> - bl2 at 40000 {
> - reg = <0x00040000 0x140000>;
> - read-only;
> - };
> - cert_header_sa6 at 180000 {
> - reg = <0x00180000 0x040000>;
> - read-only;
> - };
> - bl31 at 1c0000 {
> - reg = <0x001c0000 0x040000>;
> - read-only;
> - };
> - tee at 200000 {
> - reg = <0x00200000 0x440000>;
> - read-only;
> - };
> - uboot at 640000 {
> - reg = <0x00640000 0x100000>;
> - read-only;
> - };
> - dtb at 740000 {
> - reg = <0x00740000 0x080000>;
> - };
> - kernel at 7c0000 {
> - reg = <0x007c0000 0x1400000>;
> - };
> - user at 1bc0000 {
> - reg = <0x01bc0000 0x2440000>;
> - };
> - };
> - };
> -};
> -
> -&rwdt {
> - timeout-sec = <60>;
> - status = "okay";
> -};
> -
> -#ifdef SOC_HAS_SATA
> -&sata {
> - status = "okay";
> -};
> -#endif /* SOC_HAS_SATA */
> -
> -&scif1 {
> - pinctrl-0 = <&scif1_pins>;
> - pinctrl-names = "default";
> -
> - uart-has-rtscts;
> - /* Please only enable hscif1 or scif1 */
> - /* status = "okay"; */
> -};
> -
> -&scif2 {
> - pinctrl-0 = <&scif2_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -&scif_clk {
> - clock-frequency = <14745600>;
> -};
> -
> -&sdhi0 {
> - pinctrl-0 = <&sdhi0_pins>;
> - pinctrl-1 = <&sdhi0_pins_uhs>;
> - pinctrl-names = "default", "state_uhs";
> -
> - vmmc-supply = <&vcc_sdhi0>;
> - vqmmc-supply = <&vccq_sdhi0>;
> - cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
> - wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
> - bus-width = <4>;
> - sd-uhs-sdr50;
> - sd-uhs-sdr104;
> - status = "okay";
> -};
> -
> -&sdhi2 {
> - /* used for on-board 8bit eMMC */
> - pinctrl-0 = <&sdhi2_pins>;
> - pinctrl-1 = <&sdhi2_pins>;
> - pinctrl-names = "default", "state_uhs";
> -
> - vmmc-supply = <®_3p3v>;
> - vqmmc-supply = <®_1p8v>;
> - bus-width = <8>;
> - mmc-hs200-1_8v;
> - mmc-hs400-1_8v;
> - no-sd;
> - no-sdio;
> - non-removable;
> - fixed-emmc-driver-type = <1>;
> - full-pwr-cycle-in-suspend;
> - status = "okay";
> -};
> -
> -&sdhi3 {
> - pinctrl-0 = <&sdhi3_pins>;
> - pinctrl-1 = <&sdhi3_pins_uhs>;
> - pinctrl-names = "default", "state_uhs";
> -
> - vmmc-supply = <&vcc_sdhi3>;
> - vqmmc-supply = <&vccq_sdhi3>;
> - cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
> - wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
> - bus-width = <4>;
> - sd-uhs-sdr50;
> - sd-uhs-sdr104;
> - status = "okay";
> -};
> -
> -&ssi1 {
> - shared-pin;
> -};
> -
> -&usb_extal_clk {
> - clock-frequency = <50000000>;
> -};
> -
> -&usb2_phy0 {
> - pinctrl-0 = <&usb0_pins>;
> - pinctrl-names = "default";
> -
> - vbus-supply = <&vbus0_usb2>;
> - status = "okay";
> -};
> -
> -&usb2_phy1 {
> - pinctrl-0 = <&usb1_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -&usb3_peri0 {
> - phys = <&usb3_phy0>;
> - phy-names = "usb";
> -
> - companion = <&xhci0>;
> -
> - status = "okay";
> -};
> -
> -&usb3_phy0 {
> - status = "okay";
> -};
> -
> -&usb3s0_clk {
> - clock-frequency = <100000000>;
> -};
> -
> -&vin0 {
> - status = "okay";
> -};
> -
> -&vin1 {
> - status = "okay";
> -};
> -
> -&vin2 {
> - status = "okay";
> -};
> -
> -&vin3 {
> - status = "okay";
> -};
> -
> -&vin4 {
> - status = "okay";
> -};
> -
> -&vin5 {
> - status = "okay";
> -};
> -
> -&vin6 {
> - status = "okay";
> -};
> -
> -&vin7 {
> - status = "okay";
> -};
> -
> -&xhci0 {
> - pinctrl-0 = <&usb30_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -#ifdef SOC_HAS_USB2_CH2
> -&ehci2 {
> - status = "okay";
> -};
> -
> -&ohci2 {
> - status = "okay";
> -};
> -
> -&pfc {
> - usb2_pins: usb2 {
> - groups = "usb2";
> - function = "usb2";
> - };
> -};
> -
> -&usb2_phy2 {
> - pinctrl-0 = <&usb2_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -#endif /* SOC_HAS_USB2_CH2 */
> diff --git a/arch/arm/dts/salvator-x.dtsi b/arch/arm/dts/salvator-x.dtsi
> deleted file mode 100644
> index ddee50e6463..00000000000
> --- a/arch/arm/dts/salvator-x.dtsi
> +++ /dev/null
> @@ -1,29 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree Source for the Salvator-X board
> - *
> - * Copyright (C) 2015-2016 Renesas Electronics Corp.
> - */
> -
> -#include "salvator-common.dtsi"
> -
> -/ {
> - model = "Renesas Salvator-X board";
> - compatible = "renesas,salvator-x";
> -};
> -
> -&extal_clk {
> - clock-frequency = <16666666>;
> -};
> -
> -&i2c4 {
> - clock-frequency = <400000>;
> -
> - versaclock5: clock-generator at 6a {
> - compatible = "idt,5p49v5923";
> - reg = <0x6a>;
> - #clock-cells = <1>;
> - clocks = <&x23_clk>;
> - clock-names = "xin";
> - };
> -};
> diff --git a/arch/arm/dts/salvator-xs.dtsi b/arch/arm/dts/salvator-xs.dtsi
> deleted file mode 100644
> index 08b925624e1..00000000000
> --- a/arch/arm/dts/salvator-xs.dtsi
> +++ /dev/null
> @@ -1,85 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree Source for the Salvator-X 2nd version board
> - *
> - * Copyright (C) 2015-2017 Renesas Electronics Corp.
> - */
> -
> -#include "salvator-common.dtsi"
> -
> -/ {
> - model = "Renesas Salvator-X 2nd version board";
> - compatible = "renesas,salvator-xs";
> -};
> -
> -&extal_clk {
> - clock-frequency = <16640000>;
> -};
> -
> -&i2c4 {
> - clock-frequency = <400000>;
> -
> - versaclock6: clock-generator at 6a {
> - compatible = "idt,5p49v6901";
> - reg = <0x6a>;
> - #clock-cells = <1>;
> - clocks = <&x23_clk>;
> - clock-names = "xin";
> - };
> -};
> -
> -#ifdef SOC_HAS_SATA
> -&pca9654 {
> - pcie-sata-switch-hog {
> - gpio-hog;
> - gpios = <7 GPIO_ACTIVE_HIGH>;
> - output-low; /* enable SATA by default */
> - line-name = "PCIE/SATA switch";
> - };
> -};
> -
> -/* SW12-7 must be set 'Off' (MD12 set to 1) which is not the default! */
> -#endif /* SOC_HAS_SATA */
> -
> -#ifdef SOC_HAS_USB2_CH3
> -&ehci3 {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&hsusb3 {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&ohci3 {
> - dr_mode = "otg";
> - status = "okay";
> -};
> -
> -&pfc {
> - /*
> - * - On Salvator-X[S], GP6_3[01] are connected to ADV7482 as irq pins
> - * (when SW31 is the default setting on Salvator-XS).
> - * - If SW31 is the default setting, you cannot use USB2.0 ch3 on
> - * r8a77951 with Salvator-XS.
> - * Hence the SW31 setting must be changed like 2) below.
> - * 1) Default setting of SW31: ON-ON-OFF-OFF-OFF-OFF:
> - * - Connect GP6_3[01] to ADV7842.
> - * 2) Changed setting of SW31: OFF-OFF-ON-ON-ON-ON:
> - * - Connect GP6_3[01] to BD082065 (USB2.0 ch3's host power).
> - * - Connect GP6_{04,21} to ADV7842.
> - */
> - usb2_ch3_pins: usb2_ch3 {
> - groups = "usb2_ch3";
> - function = "usb2_ch3";
> - };
> -};
> -
> -&usb2_phy3 {
> - pinctrl-0 = <&usb2_ch3_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -#endif /* SOC_HAS_USB2_CH3 */
> diff --git a/arch/arm/dts/ulcb-audio-graph-card.dtsi b/arch/arm/dts/ulcb-audio-graph-card.dtsi
> deleted file mode 100644
> index 3be54df645e..00000000000
> --- a/arch/arm/dts/ulcb-audio-graph-card.dtsi
> +++ /dev/null
> @@ -1,85 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree for ULCB + Audio Graph Card
> - *
> - * Copyright (C) 2022 Renesas Electronics Corp.
> - */
> -
> -/*
> - * (A) CPU0 <-----> ak4613
> - * (B) CPU1 -----> HDMI
> - *
> - * (A) aplay -D plughw:0,0 xxx.wav
> - * (B) aplay -D plughw:0,1 xxx.wav
> - *
> - * (A) arecord -D plughw:0,0 xxx.wav
> - */
> -
> -/ {
> - sound_card: sound {
> - compatible = "audio-graph-card";
> - label = "rcar-sound";
> -
> - dais = <&rsnd_port0 /* (A) CPU0 <-> ak4613 */
> - &rsnd_port1 /* (B) CPU1 -> HDMI */
> - >;
> - };
> -};
> -
> -&ak4613 {
> - #sound-dai-cells = <0>;
> -
> - port {
> - /*
> - * (A) CPU0 <-> ak4613
> - */
> - ak4613_endpoint: endpoint {
> - remote-endpoint = <&rsnd_for_ak4613>;
> - };
> - };
> -};
> -
> -&hdmi0 {
> - ports {
> - port at 2 {
> - /*
> - * (B) CPU1 -> HDMI
> - */
> - dw_hdmi0_snd_in: endpoint {
> - remote-endpoint = <&rsnd_for_hdmi>;
> - };
> - };
> - };
> -};
> -
> -&rcar_sound {
> - ports {
> - #address-cells = <1>;
> - #size-cells = <0>;
> - rsnd_port0: port at 0 {
> - /*
> - * (A) CPU0 <-> ak4613
> - */
> - reg = <0>;
> - rsnd_for_ak4613: endpoint {
> - remote-endpoint = <&ak4613_endpoint>;
> - bitclock-master;
> - frame-master;
> - playback = <&ssi0>, <&src0>, <&dvc0>;
> - capture = <&ssi1>, <&src1>, <&dvc1>;
> - };
> - };
> - rsnd_port1: port at 1 {
> - /*
> - * (B) CPU1 -> HDMI
> - */
> - reg = <1>;
> - rsnd_for_hdmi: endpoint {
> - remote-endpoint = <&dw_hdmi0_snd_in>;
> - bitclock-master;
> - frame-master;
> - playback = <&ssi2>;
> - };
> - };
> - };
> -};
> diff --git a/arch/arm/dts/ulcb-audio-graph-card2.dtsi b/arch/arm/dts/ulcb-audio-graph-card2.dtsi
> deleted file mode 100644
> index 5ebec123584..00000000000
> --- a/arch/arm/dts/ulcb-audio-graph-card2.dtsi
> +++ /dev/null
> @@ -1,26 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree for ULCB + Audio Graph Card2
> - *
> - * Copyright (C) 2022 Renesas Electronics Corp.
> - */
> -
> -/*
> - * (A) CPU0 <----> ak4613
> - * (B) CPU1 ----> HDMI
> - *
> - * (A) aplay -D plughw:0,0 xxx.wav
> - * (B) aplay -D plughw:0,1 xxx.wav
> - *
> - * (A) arecord -D plughw:0,0 xxx.wav
> - */
> -#include "ulcb-audio-graph-card.dtsi"
> -
> -&sound_card {
> - compatible = "audio-graph-card2";
> -
> - /delete-property/ dais;
> - links = <&rsnd_port0 /* (A) CPU0 <-> ak4613 */
> - &rsnd_port1 /* (B) CPU1 -> HDMI */
> - >;
> -};
> diff --git a/arch/arm/dts/ulcb.dtsi b/arch/arm/dts/ulcb.dtsi
> deleted file mode 100644
> index 0be2716659e..00000000000
> --- a/arch/arm/dts/ulcb.dtsi
> +++ /dev/null
> @@ -1,509 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -/*
> - * Device Tree Source for the R-Car Gen3 ULCB board
> - *
> - * Copyright (C) 2016 Renesas Electronics Corp.
> - * Copyright (C) 2016 Cogent Embedded, Inc.
> - */
> -
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/input/input.h>
> -
> -/ {
> - model = "Renesas R-Car Gen3 ULCB board";
> -
> - aliases {
> - i2c0 = &i2c0;
> - i2c1 = &i2c1;
> - i2c2 = &i2c2;
> - i2c3 = &i2c3;
> - i2c4 = &i2c4;
> - i2c5 = &i2c5;
> - i2c6 = &i2c6;
> - i2c7 = &i2c_dvfs;
> - serial0 = &scif2;
> - ethernet0 = &avb;
> - mmc0 = &sdhi2;
> - mmc1 = &sdhi0;
> - };
> -
> - chosen {
> - bootargs = "ignore_loglevel rw root=/dev/nfs ip=on";
> - stdout-path = "serial0:115200n8";
> - };
> -
> - audio_clkout: audio-clkout {
> - /*
> - * This is same as <&rcar_sound 0>
> - * but needed to avoid cs2000/rcar_sound probe dead-lock
> - */
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <12288000>;
> - };
> -
> - hdmi0-out {
> - compatible = "hdmi-connector";
> - type = "a";
> -
> - port {
> - hdmi0_con: endpoint {
> - remote-endpoint = <&rcar_dw_hdmi0_out>;
> - };
> - };
> - };
> -
> - keyboard {
> - compatible = "gpio-keys";
> -
> - key-1 {
> - linux,code = <KEY_1>;
> - label = "SW3";
> - wakeup-source;
> - debounce-interval = <20>;
> - gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
> - };
> - };
> -
> - leds {
> - compatible = "gpio-leds";
> -
> - led5 {
> - gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
> - };
> - led6 {
> - gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
> - };
> - };
> -
> - reg_1p8v: regulator-1p8v {
> - compatible = "regulator-fixed";
> - regulator-name = "fixed-1.8V";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - reg_3p3v: regulator-3p3v {
> - compatible = "regulator-fixed";
> - regulator-name = "fixed-3.3V";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - vcc_sdhi0: regulator-vcc-sdhi0 {
> - compatible = "regulator-fixed";
> -
> - regulator-name = "SDHI0 Vcc";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
> - enable-active-high;
> - };
> -
> - vccq_sdhi0: regulator-vccq-sdhi0 {
> - compatible = "regulator-gpio";
> -
> - regulator-name = "SDHI0 VccQ";
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <3300000>;
> -
> - gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
> - gpios-states = <1>;
> - states = <3300000 1>, <1800000 0>;
> - };
> -
> - x12_clk: x12 {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <24576000>;
> - };
> -
> - x23_clk: x23-clock {
> - compatible = "fixed-clock";
> - #clock-cells = <0>;
> - clock-frequency = <25000000>;
> - };
> -};
> -
> -&a57_0 {
> - cpu-supply = <&dvfs>;
> -};
> -
> -&audio_clk_a {
> - clock-frequency = <22579200>;
> -};
> -
> -&avb {
> - pinctrl-0 = <&avb_pins>;
> - pinctrl-names = "default";
> - phy-handle = <&phy0>;
> - tx-internal-delay-ps = <2000>;
> - status = "okay";
> -
> - phy0: ethernet-phy at 0 {
> - compatible = "ethernet-phy-id0022.1622",
> - "ethernet-phy-ieee802.3-c22";
> - rxc-skew-ps = <1500>;
> - reg = <0>;
> - interrupt-parent = <&gpio2>;
> - interrupts = <11 IRQ_TYPE_LEVEL_LOW>;
> - reset-gpios = <&gpio2 10 GPIO_ACTIVE_LOW>;
> - };
> -};
> -
> -&du {
> - status = "okay";
> -};
> -
> -&ehci1 {
> - status = "okay";
> -};
> -
> -&extal_clk {
> - clock-frequency = <16666666>;
> -};
> -
> -&extalr_clk {
> - clock-frequency = <32768>;
> -};
> -
> -&hdmi0 {
> - status = "okay";
> -
> - ports {
> - port at 1 {
> - reg = <1>;
> - rcar_dw_hdmi0_out: endpoint {
> - remote-endpoint = <&hdmi0_con>;
> - };
> - };
> - port at 2 {
> - reg = <2>;
> - };
> - };
> -};
> -
> -&i2c2 {
> - pinctrl-0 = <&i2c2_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -
> - clock-frequency = <100000>;
> -
> - ak4613: codec at 10 {
> - compatible = "asahi-kasei,ak4613";
> - reg = <0x10>;
> - clocks = <&rcar_sound 3>;
> -
> - asahi-kasei,in1-single-end;
> - asahi-kasei,in2-single-end;
> - asahi-kasei,out1-single-end;
> - asahi-kasei,out2-single-end;
> - asahi-kasei,out3-single-end;
> - asahi-kasei,out4-single-end;
> - asahi-kasei,out5-single-end;
> - asahi-kasei,out6-single-end;
> - };
> -
> - cs2000: clk-multiplier at 4f {
> - #clock-cells = <0>;
> - compatible = "cirrus,cs2000-cp";
> - reg = <0x4f>;
> - clocks = <&audio_clkout>, <&x12_clk>;
> - clock-names = "clk_in", "ref_clk";
> -
> - assigned-clocks = <&cs2000>;
> - assigned-clock-rates = <24576000>; /* 1/1 divide */
> - };
> -};
> -
> -&i2c4 {
> - status = "okay";
> -
> - clock-frequency = <400000>;
> -
> - versaclock5: clock-generator at 6a {
> - compatible = "idt,5p49v5925";
> - reg = <0x6a>;
> - #clock-cells = <1>;
> - clocks = <&x23_clk>;
> - clock-names = "xin";
> - };
> -};
> -
> -&i2c_dvfs {
> - status = "okay";
> -
> - clock-frequency = <400000>;
> -
> - pmic: pmic at 30 {
> - pinctrl-0 = <&irq0_pins>;
> - pinctrl-names = "default";
> -
> - compatible = "rohm,bd9571mwv";
> - reg = <0x30>;
> - interrupt-parent = <&intc_ex>;
> - interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> - interrupt-controller;
> - #interrupt-cells = <2>;
> - gpio-controller;
> - #gpio-cells = <2>;
> - rohm,ddr-backup-power = <0xf>;
> - rohm,rstbmode-pulse;
> -
> - regulators {
> - dvfs: dvfs {
> - regulator-name = "dvfs";
> - regulator-min-microvolt = <750000>;
> - regulator-max-microvolt = <1030000>;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> - };
> - };
> -
> - eeprom at 50 {
> - compatible = "rohm,br24t01", "atmel,24c01";
> - reg = <0x50>;
> - pagesize = <8>;
> - };
> -};
> -
> -&ohci1 {
> - status = "okay";
> -};
> -
> -&pfc {
> - pinctrl-0 = <&scif_clk_pins>;
> - pinctrl-names = "default";
> -
> - avb_pins: avb {
> - mux {
> - groups = "avb_link", "avb_mdio", "avb_mii";
> - function = "avb";
> - };
> -
> - pins_mdio {
> - groups = "avb_mdio";
> - drive-strength = <24>;
> - };
> -
> - pins_mii_tx {
> - pins = "PIN_AVB_TX_CTL", "PIN_AVB_TXC", "PIN_AVB_TD0",
> - "PIN_AVB_TD1", "PIN_AVB_TD2", "PIN_AVB_TD3";
> - drive-strength = <12>;
> - };
> - };
> -
> - i2c2_pins: i2c2 {
> - groups = "i2c2_a";
> - function = "i2c2";
> - };
> -
> - irq0_pins: irq0 {
> - groups = "intc_ex_irq0";
> - function = "intc_ex";
> - };
> -
> - scif2_pins: scif2 {
> - groups = "scif2_data_a";
> - function = "scif2";
> - };
> -
> - scif_clk_pins: scif_clk {
> - groups = "scif_clk_a";
> - function = "scif_clk";
> - };
> -
> - sdhi0_pins: sd0 {
> - groups = "sdhi0_data4", "sdhi0_ctrl";
> - function = "sdhi0";
> - power-source = <3300>;
> - };
> -
> - sdhi0_pins_uhs: sd0_uhs {
> - groups = "sdhi0_data4", "sdhi0_ctrl";
> - function = "sdhi0";
> - power-source = <1800>;
> - };
> -
> - sdhi2_pins: sd2 {
> - groups = "sdhi2_data8", "sdhi2_ctrl", "sdhi2_ds";
> - function = "sdhi2";
> - power-source = <1800>;
> - };
> -
> - sound_pins: sound {
> - groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
> - function = "ssi";
> - };
> -
> - sound_clk_pins: sound-clk {
> - groups = "audio_clk_a_a", "audio_clk_b_a", "audio_clk_c_a",
> - "audio_clkout_a", "audio_clkout3_a";
> - function = "audio_clk";
> - };
> -
> - usb1_pins: usb1 {
> - groups = "usb1";
> - function = "usb1";
> - };
> -};
> -
> -&rcar_sound {
> - pinctrl-0 = <&sound_pins>, <&sound_clk_pins>;
> - pinctrl-names = "default";
> -
> - /* audio_clkout0/1/2/3 */
> - #clock-cells = <1>;
> - clock-frequency = <12288000 11289600>;
> -
> - status = "okay";
> -
> - /* update <audio_clk_b> to <cs2000> */
> - clocks = <&cpg CPG_MOD 1005>,
> - <&cpg CPG_MOD 1006>, <&cpg CPG_MOD 1007>,
> - <&cpg CPG_MOD 1008>, <&cpg CPG_MOD 1009>,
> - <&cpg CPG_MOD 1010>, <&cpg CPG_MOD 1011>,
> - <&cpg CPG_MOD 1012>, <&cpg CPG_MOD 1013>,
> - <&cpg CPG_MOD 1014>, <&cpg CPG_MOD 1015>,
> - <&cpg CPG_MOD 1022>, <&cpg CPG_MOD 1023>,
> - <&cpg CPG_MOD 1024>, <&cpg CPG_MOD 1025>,
> - <&cpg CPG_MOD 1026>, <&cpg CPG_MOD 1027>,
> - <&cpg CPG_MOD 1028>, <&cpg CPG_MOD 1029>,
> - <&cpg CPG_MOD 1030>, <&cpg CPG_MOD 1031>,
> - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
> - <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
> - <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
> - <&audio_clk_a>, <&cs2000>,
> - <&audio_clk_c>,
> - <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
> -};
> -
> -&rpc {
> - /* Left disabled. To be enabled by firmware when unlocked. */
> -
> - flash at 0 {
> - compatible = "cypress,hyperflash", "cfi-flash";
> - reg = <0>;
> -
> - partitions {
> - compatible = "fixed-partitions";
> - #address-cells = <1>;
> - #size-cells = <1>;
> -
> - bootparam at 0 {
> - reg = <0x00000000 0x040000>;
> - read-only;
> - };
> - bl2 at 40000 {
> - reg = <0x00040000 0x140000>;
> - read-only;
> - };
> - cert_header_sa6 at 180000 {
> - reg = <0x00180000 0x040000>;
> - read-only;
> - };
> - bl31 at 1c0000 {
> - reg = <0x001c0000 0x040000>;
> - read-only;
> - };
> - tee at 200000 {
> - reg = <0x00200000 0x440000>;
> - read-only;
> - };
> - uboot at 640000 {
> - reg = <0x00640000 0x100000>;
> - read-only;
> - };
> - dtb at 740000 {
> - reg = <0x00740000 0x080000>;
> - };
> - kernel at 7c0000 {
> - reg = <0x007c0000 0x1400000>;
> - };
> - user at 1bc0000 {
> - reg = <0x01bc0000 0x2440000>;
> - };
> - };
> - };
> -};
> -
> -&rwdt {
> - timeout-sec = <60>;
> - status = "okay";
> -};
> -
> -&scif2 {
> - pinctrl-0 = <&scif2_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -&scif_clk {
> - clock-frequency = <14745600>;
> -};
> -
> -&sdhi0 {
> - pinctrl-0 = <&sdhi0_pins>;
> - pinctrl-1 = <&sdhi0_pins_uhs>;
> - pinctrl-names = "default", "state_uhs";
> -
> - vmmc-supply = <&vcc_sdhi0>;
> - vqmmc-supply = <&vccq_sdhi0>;
> - cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
> - bus-width = <4>;
> - sd-uhs-sdr50;
> - sd-uhs-sdr104;
> - status = "okay";
> -};
> -
> -&sdhi2 {
> - /* used for on-board 8bit eMMC */
> - pinctrl-0 = <&sdhi2_pins>;
> - pinctrl-1 = <&sdhi2_pins>;
> - pinctrl-names = "default", "state_uhs";
> -
> - vmmc-supply = <®_3p3v>;
> - vqmmc-supply = <®_1p8v>;
> - bus-width = <8>;
> - mmc-hs200-1_8v;
> - mmc-hs400-1_8v;
> - no-sd;
> - no-sdio;
> - non-removable;
> - full-pwr-cycle-in-suspend;
> - status = "okay";
> -};
> -
> -&ssi1 {
> - shared-pin;
> -};
> -
> -&usb2_phy1 {
> - pinctrl-0 = <&usb1_pins>;
> - pinctrl-names = "default";
> -
> - status = "okay";
> -};
> -
> -
> -/*
> - * For sound-test.
> - *
> - * We can switch Audio Card for testing
> - *
> - * #include "ulcb-simple-audio-card.dtsi"
> - * #include "ulcb-simple-audio-card-mix+split.dtsi"
> - * #include "ulcb-audio-graph-card.dtsi"
> - * #include "ulcb-audio-graph-card-mix+split.dtsi"
> - * #include "ulcb-audio-graph-card2-mix+split.dtsi"
> - */
> -#include "ulcb-audio-graph-card2.dtsi"
> --
> 2.43.0
>
More information about the U-Boot
mailing list