[PATCH 04/10] ARM: socfpga: add Enclustra storage switch
Lothar Rubusch
l.rubusch at gmail.com
Sun Oct 13 16:32:26 CEST 2024
Some of Enclustra's Intel SoMs need gpio muxing for setting up
the boot media. This can be done by switching dip switches and also in
software. The image in this case can be loaded from SD card, and flashed
to the eMMC or QSPI. After, the dip switches can set the boot select
accordingly. With altera_set_storage MMC|EMMC|QSPI from off the u-boot
shell, the media is usually switched.
Signed-off-by: Lothar Rubusch <l.rubusch at gmail.com>
---
.../socfpga_arria10_enclustra_mercury_aa1.dts | 17 ++
board/enclustra/mercury_aa1/Makefile | 8 +
.../mercury_aa1/aa1_set_storage_cmd.c | 190 ++++++++++++++++++
doc/board/enclustra/mercury-aa1.rst | 29 ++-
4 files changed, 241 insertions(+), 3 deletions(-)
create mode 100644 board/enclustra/mercury_aa1/Makefile
create mode 100644 board/enclustra/mercury_aa1/aa1_set_storage_cmd.c
diff --git a/arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts b/arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts
index 1b29ab9358..c33419729d 100644
--- a/arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts
+++ b/arch/arm/dts/socfpga_arria10_enclustra_mercury_aa1.dts
@@ -5,6 +5,8 @@
/dts-v1/;
+#include <dt-bindings/gpio/gpio.h>
+
/* The arria10 family */
#include "socfpga/socfpga_arria10_mercury_aa1.dtsi"
@@ -17,6 +19,13 @@
i2c1 = &i2c0;
spi0 = &qspi;
};
+
+ altera_set_storage {
+ compatible = "encl,altera_set_storage";
+ status = "okay";
+ oe-gpios = <&portb 5 GPIO_ACTIVE_HIGH>;
+ sel-gpios = <&portc 6 GPIO_ACTIVE_HIGH>;
+ };
};
&qspi {
@@ -35,6 +44,14 @@
};
};
+&gpio1 {
+ status = "okay";
+};
+
+&gpio2 {
+ status = "okay";
+};
+
/* Carrier board support */
#if IS_ENABLED(CONFIG_ENCLUSTRA_PE1)
# include "socfpga/socfpga_enclustra_mercury_pe1.dtsi"
diff --git a/board/enclustra/mercury_aa1/Makefile b/board/enclustra/mercury_aa1/Makefile
new file mode 100644
index 0000000000..53c84d8156
--- /dev/null
+++ b/board/enclustra/mercury_aa1/Makefile
@@ -0,0 +1,8 @@
+# SPDX-License-Identifier: GPL-2.0+
+# Copyright (c) 2024 Enclustra GmbH
+
+ifeq ($(CONFIG_SPL_BUILD),)
+
+obj-y += aa1_set_storage_cmd.o
+
+endif
diff --git a/board/enclustra/mercury_aa1/aa1_set_storage_cmd.c b/board/enclustra/mercury_aa1/aa1_set_storage_cmd.c
new file mode 100644
index 0000000000..95438c5487
--- /dev/null
+++ b/board/enclustra/mercury_aa1/aa1_set_storage_cmd.c
@@ -0,0 +1,190 @@
+// SPDX-License-Identifier: GPL-2.0+
+/*
+ * Copyright (C) 2024 Enclustra GmbH
+ * <info at enclustra.com>
+ */
+
+#include <command.h>
+#include <env.h>
+#include <init.h>
+#include <dm.h>
+#include <dm/uclass.h>
+#include <asm-generic/gpio.h>
+#include <asm/io.h>
+
+/* Pin muxing */
+#define ALTERA_NONE 0
+#define ALTERA_MMC 1
+#define ALTERA_QSPI 2
+#define ALTERA_EMMC 3
+#define MMC_CLK_DIV 0x9
+#define QSPI_CLK_DIV 0x384
+#define ALTERA_PINMUX_OFFS 0xffd07200
+#define ALTERA_CLKMGR_MAINPLL_CNTR6CLK_BASE 0xFFD04078
+
+static int altera_current_storage = ALTERA_NONE;
+
+static const struct udevice_id altera_set_storage_match[] = {
+ { .compatible = "encl,altera_set_storage" },
+ { }
+};
+
+U_BOOT_DRIVER(altera_set_storage) = {
+ .name = "altera_set_storage",
+ .id = UCLASS_MISC,
+ .of_match = altera_set_storage_match,
+};
+
+static void enclustra_mercury_aa1_write(const u32 *pinmux_arr, int len)
+{
+ u32 i, offset, value;
+
+ for (i = 0; i < len; i += 2) {
+ offset = pinmux_arr[i];
+ value = pinmux_arr[i + 1];
+ writel(value, ALTERA_PINMUX_OFFS + offset);
+ }
+}
+
+static void enclustra_mercury_aa1_set_mux_mmc(void)
+{
+ static const u32 pinmux_arr[] = {0x0c, 0x8, // IO4 connected to SDMMC
+ 0x10, 0x8, // IO5
+ 0x14, 0x8, // IO6
+ 0x18, 0x8, // IO7
+ 0x1c, 0x8, // IO8
+ 0x20, 0x8, // IO9
+ 0x24, 0xf, // IO10 connected to GPIO
+ 0x28, 0xf, // IO11
+ 0x2c, 0xf, // IO12
+ 0x30, 0xf, // IO13
+ 0x34, 0xf, // IO14
+ 0x38, 0xf}; // IO15
+ enclustra_mercury_aa1_write(pinmux_arr, sizeof(pinmux_arr) / sizeof(u32));
+}
+
+static void enclustra_mercury_aa1_set_mux_emmc(void)
+{
+ static const u32 pinmux_arr[] = {0x0c, 0x8, // IO4
+ 0x10, 0x8, // IO5
+ 0x14, 0x8, // IO6
+ 0x18, 0x8, // IO7
+ 0x1c, 0x8, // IO8
+ 0x20, 0x8, // IO9
+ 0x24, 0xf, // IO10
+ 0x28, 0xf, // IO11
+ 0x2c, 0x8, // IO12
+ 0x30, 0x8, // IO13
+ 0x34, 0x8, // IO14
+ 0x38, 0x8}; // IO15
+ enclustra_mercury_aa1_write(pinmux_arr, sizeof(pinmux_arr) / sizeof(u32));
+}
+
+static void enclustra_mercury_aa1_set_mux_qspi(void)
+{
+ static const u32 pinmux_arr[] = {0x0c, 0x4, // IO4 connected to QSPI
+ 0x10, 0x4, // IO5
+ 0x14, 0x4, // IO6
+ 0x18, 0x4, // IO7
+ 0x1c, 0x4, // IO8
+ 0x20, 0x4, // IO9
+ 0x24, 0xf, // IO10
+ 0x28, 0xf, // IO11
+ 0x2c, 0xf, // IO12
+ 0x30, 0xf, // IO13
+ 0x34, 0xf, // IO14
+ 0x38, 0xf}; // IO15
+ enclustra_mercury_aa1_write(pinmux_arr, sizeof(pinmux_arr) / sizeof(u32));
+}
+
+static int altera_set_storage(struct udevice *dev, int store)
+{
+ struct gpio_desc gpio_flash_sel;
+ struct gpio_desc gpio_flash_oe;
+ int ret;
+
+ if (store == altera_current_storage)
+ return CMD_RET_FAILURE;
+
+ /* oe: portb 5 */
+ ret = gpio_request_by_name(dev, "oe-gpios", 0,
+ &gpio_flash_oe, GPIOD_IS_OUT);
+
+ if (ret) {
+ printf("ERROR: GPIO oe not found\n");
+ return log_msg_ret("gpio", ret);
+ }
+
+ /* sel: portc 6 */
+ ret = gpio_request_by_name(dev, "sel-gpios", 0,
+ &gpio_flash_sel, GPIOD_IS_OUT);
+ if (ret) {
+ printf("ERROR: GPIO sel not found\n");
+ ret = CMD_RET_FAILURE;
+ goto err;
+ }
+
+ switch (store) {
+ case ALTERA_MMC:
+ enclustra_mercury_aa1_set_mux_mmc();
+ dm_gpio_set_value(&gpio_flash_sel, 0);
+ dm_gpio_set_value(&gpio_flash_oe, 0);
+ altera_current_storage = ALTERA_MMC;
+ writel(MMC_CLK_DIV, ALTERA_CLKMGR_MAINPLL_CNTR6CLK_BASE);
+ break;
+ case ALTERA_EMMC:
+ enclustra_mercury_aa1_set_mux_emmc();
+ dm_gpio_set_value(&gpio_flash_sel, 1);
+ dm_gpio_set_value(&gpio_flash_oe, 1);
+ altera_current_storage = ALTERA_EMMC;
+ writel(MMC_CLK_DIV, ALTERA_CLKMGR_MAINPLL_CNTR6CLK_BASE);
+ break;
+ case ALTERA_QSPI:
+ enclustra_mercury_aa1_set_mux_qspi();
+ dm_gpio_set_value(&gpio_flash_sel, 1);
+ dm_gpio_set_value(&gpio_flash_oe, 0);
+ altera_current_storage = ALTERA_QSPI;
+ writel(QSPI_CLK_DIV, ALTERA_CLKMGR_MAINPLL_CNTR6CLK_BASE);
+ break;
+ default:
+ altera_current_storage = ALTERA_NONE;
+ break;
+ }
+
+ ret = CMD_RET_SUCCESS;
+ dm_gpio_free(dev, &gpio_flash_sel);
+err:
+ dm_gpio_free(dev, &gpio_flash_oe);
+
+ return ret;
+}
+
+static int altera_set_storage_cmd(struct cmd_tbl *cmdtp, int flag,
+ int argc, char * const argv[])
+{
+ struct udevice *dev;
+ int ret;
+
+ ret = uclass_get_device_by_driver(UCLASS_MISC,
+ DM_DRIVER_GET(altera_set_storage), &dev);
+ if (ret)
+ return ret;
+
+ if (argc != 2)
+ return CMD_RET_USAGE;
+
+ if (!strcmp(argv[1], "MMC") || !strcmp(argv[1], "mmc"))
+ return altera_set_storage(dev, ALTERA_MMC);
+ else if (!strcmp(argv[1], "QSPI") || !strcmp(argv[1], "qspi"))
+ return altera_set_storage(dev, ALTERA_QSPI);
+ else if (!strcmp(argv[1], "EMMC") || !strcmp(argv[1], "emmc"))
+ return altera_set_storage(dev, ALTERA_EMMC);
+ else
+ return CMD_RET_USAGE;
+
+ return CMD_RET_FAILURE;
+}
+
+U_BOOT_CMD(altera_set_storage, 2, 0, altera_set_storage_cmd,
+ "Set non volatile memory access",
+ "<MMC|QSPI|EMMC> - Set access for the selected memory device");
diff --git a/doc/board/enclustra/mercury-aa1.rst b/doc/board/enclustra/mercury-aa1.rst
index 6a96bf70e3..dafc3f850c 100644
--- a/doc/board/enclustra/mercury-aa1.rst
+++ b/doc/board/enclustra/mercury-aa1.rst
@@ -149,9 +149,32 @@ Alternative boot media are possible as officially documented by Enclustra.
* QSPI
Note: eMMC and QSPI can be flashed from off the u-boot shell. Usually after
-flashing, the coorect boot mode needs to be set by a BSEL switch. Approaches
-are described consistently in the official Enclustra documentation according to
-their releases mentioned as links.
+flashing, the correct boot mode needs to be set by a BSEL switch.
+
+In the u-boot shell use the following command to switch between the boot media.
+This can be used to flash e.g. eMMC or QSPI with an image file stored on the SD
+card. Approaches are described in detail in the official Enclustra
+documentation according to their releases mentioned as links.
+
+ .. code-block:: bash
+
+ Hit any key to stop autoboot: 0
+ => altera_set_storage
+ altera_set_storage - Set non volatile memory access
+ Usage:
+ altera_set_storage <MMC|QSPI|EMMC> - Set access for the selected memory device
+ => altera_set_storage QSPI
+ => sf probe
+ SF: Detected s25fl512s with page size 256 Bytes, erase size 256 KiB, total 64 MiB
+ => altera_set_storage MMC
+ => mmc rescan
+ => mmc list
+ mmc at ff808000: 0 (SD)
+ => altera_set_storage EMMC
+ => mmc rescan
+ => mmc list
+ mmc at ff808000: 0 (eMMC)
+ =>
Before turning on the setup, make sure to have the correct voltage configured
at the carrier board, using the jumpers on the voltage pin header. Also make
--
2.25.1
More information about the U-Boot
mailing list