[PATCH 4/6] arm: mach-k3: j721e-init.c: J7200: Add support for CONFIG_K3_OPP_LOW

[Aniket Limaye]

From: Reid Tonking <reidt at ti.com>

The default j7200 devicetree and k3_avs driver set 2GHz/1GHz frequency
for A72/MSMC clks and the OPP_NOM voltage.

J7200 SOCs may support OPP_LOW Operating Performance Point:
1GHz/500MHz clks for A72/MSMC and OPP_LOW AVS voltage read from efuse.

Hence, add a config check to select OPP_LOW specs:
- Check if OPP_LOW AVS voltage read from efuse is valid.
- Update the clock frequencies in devicetree.
- Program the OPP_LOW AVS voltage for VDD_CPU.

Signed-off-by: Reid Tonking <reidt at ti.com>
Signed-off-by: Aniket Limaye <a-limaye at ti.com>
---
 arch/arm/mach-k3/j721e/j721e_init.c | 45 ++++++++++++++++++++++++++++-
 drivers/misc/k3_avs.c               |  5 ++++
 2 files changed, 49 insertions(+), 1 deletion(-)

diff --git a/arch/arm/mach-k3/j721e/j721e_init.c b/arch/arm/mach-k3/j721e/j721e_init.c
index e9ed8cb267c..0620759c36c 100644
--- a/arch/arm/mach-k3/j721e/j721e_init.c
+++ b/arch/arm/mach-k3/j721e/j721e_init.c
@@ -19,6 +19,7 @@
 #include <fdtdec.h>
 #include <mmc.h>
 #include <remoteproc.h>
+#include <k3-avs.h>
 
 #include "../sysfw-loader.h"
 #include "../common.h"
@@ -147,6 +148,32 @@ static void setup_navss_nb(void)
 	writel(NB_THREADMAP_BIT1, (uintptr_t)NAVSS0_NBSS_NB1_CFG_NB_THREADMAP);
 }
 
+int fix_freq(const void *fdt)
+{
+		int node, ret;
+		u32 opp_low_freq[3];
+
+		node = fdt_node_offset_by_compatible(fdt, -1, "ti,am654-rproc");
+			if (node < 0) {
+				printf("%s: A72 not found\n", __func__);
+				return node;
+			}
+
+		/* j7200 opp low values according to data sheet */
+		opp_low_freq[0] = cpu_to_fdt32(1000000000); /* 202-2 -> A72SS0_CORE0_0_ARM_CLK */
+		opp_low_freq[1] = cpu_to_fdt32(200000000); /* 61-1 -> GTC0_GTC_CLK */
+		opp_low_freq[2] = cpu_to_fdt32(500000000); /* 4-1 -> A72SS0_CORE0_MSMC_CLK */
+
+		ret = fdt_setprop((void *)fdt, node, "assigned-clock-rates",
+				  opp_low_freq, sizeof(opp_low_freq));
+			if (ret) {
+				printf("%s: Can not set value\n", __func__);
+				return ret;
+			}
+
+		return 0;
+}
+
 /*
  * This uninitialized global variable would normal end up in the .bss section,
  * but the .bss is cleared between writing and reading this variable, so move
@@ -301,8 +328,24 @@ void board_init_f(ulong dummy)
 #if defined(CONFIG_CPU_V7R) && defined(CONFIG_K3_AVS0)
 	ret = uclass_get_device_by_driver(UCLASS_MISC, DM_DRIVER_GET(k3_avs),
 					  &dev);
-	if (ret)
+	if (!ret) {
+		if (IS_ENABLED(CONFIG_K3_OPP_LOW)) {
+			ret = k3_check_opp(dev, J721E_VDD_MPU, AM6_OPP_LOW);
+			if (!ret) {
+				ret = fix_freq(gd->fdt_blob);
+				if (ret)
+					printf("Failed to set OPP_LOW frequency\n");
+
+				ret = k3_avs_set_opp(dev, J721E_VDD_MPU, AM6_OPP_LOW);
+				if (ret)
+					printf("Failed to set OPP_LOW voltage\n");
+			} else {
+				printf("Failed to enable K3_OPP_LOW\n");
+			}
+		}
+	} else {
 		printf("AVS init failed: %d\n", ret);
+	}
 #endif
 
 #if defined(CONFIG_K3_J721E_DDRSS)
diff --git a/drivers/misc/k3_avs.c b/drivers/misc/k3_avs.c
index 90cd9dfe7f9..932b355a5c1 100644
--- a/drivers/misc/k3_avs.c
+++ b/drivers/misc/k3_avs.c
@@ -121,6 +121,11 @@ static int k3_avs_program_voltage(struct k3_avs_privdata *priv,
 	if (!vd->supply)
 		return -ENODEV;
 
+	if (!volt) {
+		dev_err(priv->dev, "Fuse is not set for selected opp %d\n", opp_id);
+		return -EINVAL;
+	}
+
 	vd->opp = opp_id;
 	vd->flags |= VD_FLAG_INIT_DONE;
 
-- 
2.34.1