[PATCH v2 25/25] led: Drop status_led header file

[Simon Glass]

This is not needed anymore. Drop it.

Signed-off-by: Simon Glass <sjg at chromium.org>
---

Changes in v2:
- Enable LED on the 5 affected platforms
- Reorder patches for bisectability

 include/status_led.h | 104 -------------------------------------------
 1 file changed, 104 deletions(-)
 delete mode 100644 include/status_led.h

diff --git a/include/status_led.h b/include/status_led.h
deleted file mode 100644
index 59cf9f89956..00000000000
--- a/include/status_led.h
+++ /dev/null
@@ -1,104 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2000-2004
- * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
- */
-
-/*
- * The purpose of this code is to signal the operational status of a
- * target which usually boots over the network; while running in
- * PCBoot, a status LED is blinking. As soon as a valid BOOTP reply
- * message has been received, the LED is turned off. The Linux
- * kernel, once it is running, will start blinking the LED again,
- * with another frequency.
- */
-
-#ifndef _STATUS_LED_H_
-#define	_STATUS_LED_H_
-
-#ifdef CONFIG_LED_STATUS
-
-#define LED_STATUS_PERIOD	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ)
-#ifdef CONFIG_LED_STATUS1
-#define LED_STATUS_PERIOD1	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ1)
-#endif /* CONFIG_LED_STATUS1 */
-#ifdef CONFIG_LED_STATUS2
-#define LED_STATUS_PERIOD2	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ2)
-#endif /* CONFIG_LED_STATUS2 */
-#ifdef CONFIG_LED_STATUS3
-#define LED_STATUS_PERIOD3	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ3)
-#endif /* CONFIG_LED_STATUS3 */
-#ifdef CONFIG_LED_STATUS4
-#define LED_STATUS_PERIOD4	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ4)
-#endif /* CONFIG_LED_STATUS4 */
-#ifdef CONFIG_LED_STATUS5
-#define LED_STATUS_PERIOD5	(CONFIG_SYS_HZ / CONFIG_LED_STATUS_FREQ5)
-#endif /* CONFIG_LED_STATUS5 */
-
-void status_led_init(void);
-void status_led_tick(unsigned long timestamp);
-void status_led_set(int led, int state);
-
-static inline void status_led_boot_blink(void)
-{
-#ifdef CONFIG_LED_STATUS_BOOT_ENABLE
-	status_led_set(CONFIG_LED_STATUS_BOOT, CONFIG_LED_STATUS_BLINKING);
-#endif
-}
-
-/*****  MVS v1  **********************************************************/
-#if (defined(CONFIG_MVS) && CONFIG_MVS < 2)
-# define STATUS_LED_PAR		im_ioport.iop_pdpar
-# define STATUS_LED_DIR		im_ioport.iop_pddir
-# undef  STATUS_LED_ODR
-# define STATUS_LED_DAT		im_ioport.iop_pddat
-
-# define STATUS_LED_ACTIVE	1		/* LED on for bit == 1	*/
-
-/*****  Someone else defines these  *************************************/
-#elif defined(STATUS_LED_PAR)
-  /*
-   * ADVICE: Define in your board configuration file rather than
-   * filling this file up with lots of custom board stuff.
-   */
-#else
-# error Status LED configuration missing
-#endif
-/************************************************************************/
-
-#include <asm/status_led.h>
-
-#else
-
-static inline void status_led_init(void) { }
-static inline void status_led_set(int led, int state) { }
-static inline void status_led_boot_blink(void) { }
-
-#endif	/* CONFIG_LED_STATUS	*/
-
-/*
- * Coloured LEDs API
- */
-#ifndef	__ASSEMBLY__
-void coloured_LED_init(void);
-void red_led_on(void);
-void red_led_off(void);
-void green_led_on(void);
-void green_led_off(void);
-void yellow_led_on(void);
-void yellow_led_off(void);
-void blue_led_on(void);
-void blue_led_off(void);
-#else
-	.extern LED_init
-	.extern red_led_on
-	.extern red_led_off
-	.extern yellow_led_on
-	.extern yellow_led_off
-	.extern green_led_on
-	.extern green_led_off
-	.extern blue_led_on
-	.extern blue_led_off
-#endif
-
-#endif	/* _STATUS_LED_H_	*/
-- 
2.43.0