[PATCH] ARM: dts: stm32: remove unused include for dhcor
Patrick Delaunay
patrick.delaunay at foss.st.com
Mon Oct 21 18:12:28 CEST 2024
Remove device tree include files no more used with OF_UPSTREAM migration
stm32mp135f-dhcor-dhsbc.dts
Fixes: cccb29fc1270 ("ARM: dts: stm32: Switch to using upstream DT on DH
STM32 DHSOM")
Signed-off-by: Patrick Delaunay <patrick.delaunay at foss.st.com>
---
arch/arm/dts/stm32mp13xx-dhcor-som.dtsi | 308 ------------------------
1 file changed, 308 deletions(-)
delete mode 100644 arch/arm/dts/stm32mp13xx-dhcor-som.dtsi
diff --git a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi b/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi
deleted file mode 100644
index ddad6497775b..000000000000
--- a/arch/arm/dts/stm32mp13xx-dhcor-som.dtsi
+++ /dev/null
@@ -1,308 +0,0 @@
-// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
-/*
- * Copyright (C) 2024 Marek Vasut <marex at denx.de>
- */
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/leds/common.h>
-#include <dt-bindings/mfd/st,stpmic1.h>
-#include <dt-bindings/regulator/st,stm32mp13-regulator.h>
-#include "stm32mp13-pinctrl.dtsi"
-
-/ {
- model = "DH electronics STM32MP13xx DHCOR SoM";
- compatible = "dh,stm32mp131a-dhcor-som",
- "st,stm32mp131";
-
- aliases {
- mmc0 = &sdmmc2;
- mmc1 = &sdmmc1;
- serial0 = &uart4;
- serial1 = &uart7;
- rtc0 = &rv3032;
- spi0 = &qspi;
- };
-
- memory at c0000000 {
- device_type = "memory";
- reg = <0xc0000000 0x20000000>;
- };
-
- reserved-memory {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- optee at dd000000 {
- reg = <0xdd000000 0x3000000>;
- no-map;
- };
- };
-
- sdio_pwrseq: sdio-pwrseq {
- compatible = "mmc-pwrseq-simple";
- reset-gpios = <&gpiof 12 GPIO_ACTIVE_LOW>;
- };
-
- vin: vin {
- compatible = "regulator-fixed";
- regulator-name = "vin";
- regulator-min-microvolt = <5000000>;
- regulator-max-microvolt = <5000000>;
- regulator-always-on;
- };
-};
-
-&i2c3 {
- i2c-scl-rising-time-ns = <96>;
- i2c-scl-falling-time-ns = <3>;
- clock-frequency = <400000>;
- status = "okay";
- /* spare dmas for other usage */
- /delete-property/dmas;
- /delete-property/dma-names;
-
- pmic: stpmic at 33 {
- compatible = "st,stpmic1";
- reg = <0x33>;
- interrupts-extended = <&gpioi 3 IRQ_TYPE_EDGE_FALLING>;
- interrupt-controller;
- #interrupt-cells = <2>;
- status = "okay";
-
- regulators {
- compatible = "st,stpmic1-regulators";
-
- ldo1-supply = <&vin>;
- ldo2-supply = <&vin>;
- ldo3-supply = <&vin>;
- ldo4-supply = <&vin>;
- ldo5-supply = <&vin>;
- ldo6-supply = <&vin>;
- pwr_sw1-supply = <&bst_out>;
- pwr_sw2-supply = <&bst_out>;
-
- vddcpu: buck1 { /* VDD_CPU_1V2 */
- regulator-name = "vddcpu";
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_ddr: buck2 { /* VDD_DDR_1V35 */
- regulator-name = "vdd_ddr";
- regulator-min-microvolt = <1350000>;
- regulator-max-microvolt = <1350000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd: buck3 { /* VDD_3V3_1V8 */
- regulator-name = "vdd";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vddcore: buck4 { /* VDD_CORE_1V2 */
- regulator-name = "vddcore";
- regulator-min-microvolt = <1250000>;
- regulator-max-microvolt = <1250000>;
- regulator-always-on;
- regulator-initial-mode = <0>;
- regulator-over-current-protection;
- };
-
- vdd_adc: ldo1 { /* VDD_ADC_1V8 */
- regulator-name = "vdd_adc";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO1 0>;
- };
-
- vdd_ldo2: ldo2 { /* LDO2_OUT_1V8 */
- regulator-name = "vdd_ldo2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO2 0>;
- };
-
- vdd_ldo3: ldo3 { /* LDO3_OUT */
- regulator-name = "vdd_ldo3";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- interrupts = <IT_CURLIM_LDO3 0>;
- };
-
- vdd_usb: ldo4 { /* VDD_USB_3V3 */
- regulator-name = "vdd_usb";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO4 0>;
- };
-
- vdd_sd: ldo5 { /* VDD_SD_3V3_1V8 */
- regulator-name = "vdd_sd";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO5 0>;
- };
-
- vdd_sd2: ldo6 { /* VDD_SD2_3V3_1V8 */
- regulator-name = "vdd_sd2";
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <3300000>;
- interrupts = <IT_CURLIM_LDO6 0>;
- };
-
- vref_ddr: vref_ddr { /* VREF_DDR_0V675 */
- regulator-name = "vref_ddr";
- regulator-always-on;
- };
-
- bst_out: boost { /* BST_OUT_5V2 */
- regulator-name = "bst_out";
- };
-
- vbus_otg: pwr_sw1 {
- regulator-name = "vbus_otg";
- interrupts = <IT_OCP_OTG 0>;
- };
-
- vbus_sw: pwr_sw2 {
- regulator-name = "vbus_sw";
- interrupts = <IT_OCP_SWOUT 0>;
- regulator-active-discharge = <1>;
- };
- };
-
- onkey {
- compatible = "st,stpmic1-onkey";
- interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
- interrupt-names = "onkey-falling", "onkey-rising";
- status = "okay";
- };
-
- watchdog {
- compatible = "st,stpmic1-wdt";
- status = "disabled";
- };
- };
-
- eeprom0: eeprom at 50 {
- compatible = "atmel,24c256"; /* ST M24256 */
- reg = <0x50>;
- pagesize = <64>;
- };
-
- rv3032: rtc at 51 {
- compatible = "microcrystal,rv3032";
- reg = <0x51>;
- interrupts-extended = <&gpioi 0 IRQ_TYPE_EDGE_FALLING>;
- };
-};
-
-&iwdg2 {
- timeout-sec = <32>;
- status = "okay";
-};
-
-&qspi {
- pinctrl-names = "default", "sleep";
- pinctrl-0 = <&qspi_clk_pins_a
- &qspi_bk1_pins_a
- &qspi_cs1_pins_a>;
- pinctrl-1 = <&qspi_clk_sleep_pins_a
- &qspi_bk1_sleep_pins_a
- &qspi_cs1_sleep_pins_a>;
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- flash0: flash at 0 {
- compatible = "jedec,spi-nor";
- reg = <0>;
- spi-rx-bus-width = <4>;
- spi-max-frequency = <108000000>;
- #address-cells = <1>;
- #size-cells = <1>;
- };
-};
-
-/* Console UART */
-&uart4 {
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&uart4_pins_b>;
- pinctrl-1 = <&uart4_sleep_pins_b>;
- pinctrl-2 = <&uart4_idle_pins_b>;
- /delete-property/dmas;
- /delete-property/dma-names;
- status = "okay";
-};
-
-/* Bluetooth */
-&uart7 {
- pinctrl-names = "default", "sleep", "idle";
- pinctrl-0 = <&uart7_pins_a>;
- pinctrl-1 = <&uart7_sleep_pins_a>;
- pinctrl-2 = <&uart7_idle_pins_a>;
- uart-has-rtscts;
- status = "okay";
-
- bluetooth {
- compatible = "infineon,cyw43439-bt", "brcm,bcm4329-bt";
- max-speed = <3000000>;
- device-wakeup-gpios = <&gpiog 9 GPIO_ACTIVE_HIGH>;
- shutdown-gpios = <&gpioi 2 GPIO_ACTIVE_HIGH>;
- };
-};
-
-/* SDIO WiFi */
-&sdmmc1 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc1_b4_pins_a &sdmmc1_clk_pins_a>;
- pinctrl-1 = <&sdmmc1_b4_od_pins_a &sdmmc1_clk_pins_a>;
- pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
- bus-width = <4>;
- cap-power-off-card;
- keep-power-in-suspend;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&vdd>;
- mmc-pwrseq = <&sdio_pwrseq>;
- status = "okay";
-
- #address-cells = <1>;
- #size-cells = <0>;
-
- brcmf: bcrmf at 1 { /* muRata 1YN */
- reg = <1>;
- compatible = "infineon,cyw43439-fmac", "brcm,bcm4329-fmac";
- interrupt-parent = <&gpioe>;
- interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
- interrupt-names = "host-wake";
- };
-};
-
-/* eMMC */
-&sdmmc2 {
- pinctrl-names = "default", "opendrain", "sleep";
- pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
- pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_a &sdmmc2_clk_pins_a>;
- pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_a>;
- bus-width = <8>;
- mmc-ddr-3_3v;
- no-sd;
- no-sdio;
- non-removable;
- st,neg-edge;
- vmmc-supply = <&vdd>;
- vqmmc-supply = <&vdd>;
- status = "okay";
-};
--
2.25.1
More information about the U-Boot
mailing list