[PATCH] arm: Remove ethernut5 board
Tom Rini
trini at konsulko.com
Sun Sep 8 00:20:13 CEST 2024
As per the maintainers at egnite GmbH, they are no longer interested in
supporting this board. Go and remove the platform here. Furthermore,
this is the only AT91SAM9XE platform in-tree so remove supporting code
for that as well.
Signed-off-by: Tom Rini <trini at konsulko.com>
---
Cc: Harald Kipp <harald.kipp at egnite.de>
Cc: Eugen Hristev <eugen.hristev at collabora.com>
---
arch/arm/dts/Makefile | 2 -
arch/arm/dts/at91sam9xe.dtsi | 60 ----
arch/arm/dts/ethernut5.dts | 96 ------
arch/arm/mach-at91/Kconfig | 24 --
arch/arm/mach-at91/arm926ejs/Makefile | 2 -
arch/arm/mach-at91/arm926ejs/eflash.c | 255 --------------
arch/arm/mach-at91/include/mach/at91_dbu.h | 37 --
arch/arm/mach-at91/include/mach/at91_eefc.h | 47 ---
arch/arm/mach-at91/include/mach/at91sam9260.h | 12 +-
arch/arm/mach-at91/include/mach/hardware.h | 3 +-
board/egnite/ethernut5/Kconfig | 12 -
board/egnite/ethernut5/MAINTAINERS | 6 -
board/egnite/ethernut5/Makefile | 10 -
board/egnite/ethernut5/ethernut5.c | 198 -----------
board/egnite/ethernut5/ethernut5_pwrman.c | 323 ------------------
board/egnite/ethernut5/ethernut5_pwrman.h | 51 ---
configs/ethernut5_defconfig | 87 -----
doc/board/atmel/at91ek.rst | 4 +-
drivers/bootcount/Kconfig | 1 -
include/configs/at91sam9260ek.h | 6 +-
include/configs/ethernut5.h | 88 -----
21 files changed, 6 insertions(+), 1318 deletions(-)
delete mode 100644 arch/arm/dts/at91sam9xe.dtsi
delete mode 100644 arch/arm/dts/ethernut5.dts
delete mode 100644 arch/arm/mach-at91/arm926ejs/eflash.c
delete mode 100644 arch/arm/mach-at91/include/mach/at91_dbu.h
delete mode 100644 arch/arm/mach-at91/include/mach/at91_eefc.h
delete mode 100644 board/egnite/ethernut5/Kconfig
delete mode 100644 board/egnite/ethernut5/MAINTAINERS
delete mode 100644 board/egnite/ethernut5/Makefile
delete mode 100644 board/egnite/ethernut5/ethernut5.c
delete mode 100644 board/egnite/ethernut5/ethernut5_pwrman.c
delete mode 100644 board/egnite/ethernut5/ethernut5_pwrman.h
delete mode 100644 configs/ethernut5_defconfig
delete mode 100644 include/configs/ethernut5.h
diff --git a/arch/arm/dts/Makefile b/arch/arm/dts/Makefile
index 64007a20e6cc..56d4af518d80 100644
--- a/arch/arm/dts/Makefile
+++ b/arch/arm/dts/Makefile
@@ -987,8 +987,6 @@ dtb-$(CONFIG_TARGET_AT91SAM9N12EK) += at91sam9n12ek.dtb
dtb-$(CONFIG_TARGET_GARDENA_SMART_GATEWAY_AT91SAM) += \
at91sam9g25-gardena-smart-gateway.dtb
-dtb-$(CONFIG_TARGET_ETHERNUT5) += ethernut5.dtb
-
dtb-$(CONFIG_TARGET_USB_A9263) += usb_a9263.dtb
dtb-$(CONFIG_TARGET_DEVKIT8000) += omap3-devkit8000.dtb
diff --git a/arch/arm/dts/at91sam9xe.dtsi b/arch/arm/dts/at91sam9xe.dtsi
deleted file mode 100644
index 0278f63b2daf..000000000000
--- a/arch/arm/dts/at91sam9xe.dtsi
+++ /dev/null
@@ -1,60 +0,0 @@
-/*
- * at91sam9xe.dtsi - Device Tree Include file for AT91SAM9XE family SoC
- *
- * Copyright (C) 2015 Atmel,
- * 2015 Alexandre Belloni <alexandre.Belloni at free-electrons.com>
- *
- * This file is dual-licensed: you can use it either under the terms
- * of the GPL or the X11 license, at your option. Note that this dual
- * licensing only applies to this file, and not this project as a
- * whole.
- *
- * a) This file is free software; you can redistribute it and/or
- * modify it under the terms of the GNU General Public License as
- * published by the Free Software Foundation; either version 2 of the
- * License, or (at your option) any later version.
- *
- * This file is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- *
- * Or, alternatively,
- *
- * b) Permission is hereby granted, free of charge, to any person
- * obtaining a copy of this software and associated documentation
- * files (the "Software"), to deal in the Software without
- * restriction, including without limitation the rights to use,
- * copy, modify, merge, publish, distribute, sublicense, and/or
- * sell copies of the Software, and to permit persons to whom the
- * Software is furnished to do so, subject to the following
- * conditions:
- *
- * The above copyright notice and this permission notice shall be
- * included in all copies or substantial portions of the Software.
- *
- * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
- * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
- * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
- * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
- * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
- * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
- * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
- * OTHER DEALINGS IN THE SOFTWARE.
- */
-
-#include "at91sam9260.dtsi"
-
-/ {
- model = "Atmel AT91SAM9XE family SoC";
- compatible = "atmel,at91sam9xe", "atmel,at91sam9260";
-
- sram0: sram at 002ff000 {
- status = "disabled";
- };
-
- sram1: sram at 00300000 {
- compatible = "mmio-sram";
- reg = <0x00300000 0x4000>;
- };
-};
diff --git a/arch/arm/dts/ethernut5.dts b/arch/arm/dts/ethernut5.dts
deleted file mode 100644
index 5c24deaf4b64..000000000000
--- a/arch/arm/dts/ethernut5.dts
+++ /dev/null
@@ -1,96 +0,0 @@
-/*
- * ethernut5.dts - Device Tree file for Ethernut 5 board
- *
- * Copyright (C) 2012 egnite GmbH <info at egnite.de>
- *
- * Licensed under GPLv2.
- */
-/dts-v1/;
-#include "at91sam9xe.dtsi"
-
-/ {
- model = "Ethernut 5";
- compatible = "egnite,ethernut5", "atmel,at91sam9260", "atmel,at91sam9";
-
- chosen {
- bootargs = "console=ttyS0,115200 root=/dev/mtdblock0 rw rootfstype=jffs2";
- };
-
- memory {
- reg = <0x20000000 0x08000000>;
- };
-
- clocks {
- slow_xtal {
- clock-frequency = <32768>;
- };
-
- main_xtal {
- clock-frequency = <18432000>;
- };
- };
-
- ahb {
- apb {
- dbgu: serial at fffff200 {
- status = "okay";
- };
-
- usart0: serial at fffb0000 {
- status = "okay";
- };
-
- usart1: serial at fffb4000 {
- status = "okay";
- };
-
- macb0: ethernet at fffc4000 {
- phy-mode = "rmii";
- status = "okay";
- };
-
- usb1: gadget at fffa4000 {
- atmel,vbus-gpio = <&pioC 5 GPIO_ACTIVE_HIGH>;
- status = "okay";
- };
- };
-
- nand0: nand at 40000000 {
- nand-bus-width = <8>;
- nand-ecc-mode = "soft";
- nand-on-flash-bbt;
- status = "okay";
-
- gpios = <0
- &pioC 14 GPIO_ACTIVE_HIGH
- 0
- >;
-
- root at 0 {
- label = "root";
- reg = <0x0 0x08000000>;
- };
-
- data at 20000 {
- label = "data";
- reg = <0x08000000 0x38000000>;
- };
- };
-
- usb0: ohci at 00500000 {
- num-ports = <2>;
- status = "okay";
- };
- };
-
- i2c-gpio-0 {
- #address-cells = <1>;
- #size-cells = <0>;
- status = "okay";
-
- pcf8563 at 50 {
- compatible = "nxp,pcf8563";
- reg = <0x51>;
- };
- };
-};
diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig
index 8a8ac53e4f86..7c4ccc427c87 100644
--- a/arch/arm/mach-at91/Kconfig
+++ b/arch/arm/mach-at91/Kconfig
@@ -11,10 +11,6 @@ config AT91SAM9G20
bool
select CPU_ARM926EJS
-config AT91SAM9XE
- bool
- select CPU_ARM926EJS
-
config AT91SAM9261
bool
select CPU_ARM926EJS
@@ -75,10 +71,6 @@ config TARGET_AT91SAM9260EK
select AT91SAM9260
select BOARD_EARLY_INIT_F
-config TARGET_ETHERNUT5
- bool "Ethernut5 board"
- select AT91SAM9XE
-
config TARGET_GURNARD
bool "Support gurnard"
select AT91SAM9G45
@@ -340,21 +332,6 @@ config AT91RESET_EXTRST
config SYS_SOC
default "at91"
-config AT91_EFLASH
- bool "Support AT91 flash driver"
- depends on AT91SAM9XE
- select USE_SYS_MAX_FLASH_BANKS
- help
- Enable the driver for the embedded flash used in the Atmel
- AT91SAM9XE devices.
-
-config EFLASH_PROTSECTORS
- int "Number of flash sectors to protect from erasing"
- depends on AT91_EFLASH
- help
- If non-zero, this will be the number of sectors of the flash to disallow
- U-Boot to ease, starting from the beginning of flash.
-
config AT91_GPIO_PULLUP
bool "Keep pullups on peripheral pins"
depends on CPU_ARM926EJS
@@ -389,7 +366,6 @@ source "board/atmel/sama5d4ek/Kconfig"
source "board/bluewater/gurnard/Kconfig"
source "board/calao/usb_a9263/Kconfig"
source "board/conclusive/kstr-sama5d27/Kconfig"
-source "board/egnite/ethernut5/Kconfig"
source "board/esd/meesc/Kconfig"
source "board/gardena/smart-gateway-at91sam/Kconfig"
source "board/l+g/vinco/Kconfig"
diff --git a/arch/arm/mach-at91/arm926ejs/Makefile b/arch/arm/mach-at91/arm926ejs/Makefile
index 902dd3a60e3b..a8916862b3f5 100644
--- a/arch/arm/mach-at91/arm926ejs/Makefile
+++ b/arch/arm/mach-at91/arm926ejs/Makefile
@@ -5,7 +5,6 @@
obj-$(CONFIG_AT91SAM9260) += at91sam9260_devices.o
obj-$(CONFIG_AT91SAM9G20) += at91sam9260_devices.o
-obj-$(CONFIG_AT91SAM9XE) += at91sam9260_devices.o
obj-$(CONFIG_AT91SAM9261) += at91sam9261_devices.o
obj-$(CONFIG_AT91SAM9G10) += at91sam9261_devices.o
obj-$(CONFIG_AT91SAM9263) += at91sam9263_devices.o
@@ -15,7 +14,6 @@ obj-$(CONFIG_AT91SAM9G45) += at91sam9m10g45_devices.o
obj-$(CONFIG_AT91SAM9N12) += at91sam9n12_devices.o
obj-$(CONFIG_AT91SAM9X5) += at91sam9x5_devices.o
obj-$(CONFIG_SAM9X60) += sam9x60_devices.o
-obj-$(CONFIG_AT91_EFLASH) += eflash.o
obj-y += clock.o
obj-y += cpu.o
ifndef CONFIG_$(SPL_TPL_)SYSRESET
diff --git a/arch/arm/mach-at91/arm926ejs/eflash.c b/arch/arm/mach-at91/arm926ejs/eflash.c
deleted file mode 100644
index bb66700566e5..000000000000
--- a/arch/arm/mach-at91/arm926ejs/eflash.c
+++ /dev/null
@@ -1,255 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2010
- * Reinhard Meyer, EMK Elektronik, reinhard.meyer at emk-elektronik.de
- */
-
-/*
- * this driver supports the enhanced embedded flash in the Atmel
- * AT91SAM9XE devices with the following geometry:
- *
- * AT91SAM9XE128: 1 plane of 8 regions of 32 pages (total 256 pages)
- * AT91SAM9XE256: 1 plane of 16 regions of 32 pages (total 512 pages)
- * AT91SAM9XE512: 1 plane of 32 regions of 32 pages (total 1024 pages)
- * (the exact geometry is read from the flash at runtime, so any
- * future devices should already be covered)
- *
- * Regions can be write/erase protected.
- * Whole (!) pages can be individually written with erase on the fly.
- * Writing partial pages will corrupt the rest of the page.
- *
- * The flash is presented to u-boot with each region being a sector,
- * having the following effects:
- * Each sector can be hardware protected (protect on/off).
- * Each page in a sector can be rewritten anytime.
- * Since pages are erased when written, the "erase" does nothing.
- * The first "CONFIG_EFLASH_PROTSECTORS" cannot be unprotected
- * by u-Boot commands.
- *
- * Note: Redundant environment will not work in this flash since
- * it does use partial page writes. Make sure the environment spans
- * whole pages!
- */
-
-/*
- * optional TODOs (nice to have features):
- *
- * make the driver coexist with other NOR flash drivers
- * (use an index into flash_info[], requires work
- * in those other drivers, too)
- * Make the erase command fill the sectors with 0xff
- * (if the flashes grow larger in the future and
- * someone puts a jffs2 into them)
- * do a read-modify-write for partially programmed pages
- */
-#include <display_options.h>
-#include <flash.h>
-#include <log.h>
-#include <asm/io.h>
-#include <asm/arch/hardware.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/at91_eefc.h>
-#include <asm/arch/at91_dbu.h>
-
-/* checks to detect configuration errors */
-#if CONFIG_SYS_MAX_FLASH_BANKS!=1
-#error eflash: this driver can only handle 1 bank
-#endif
-
-/* global structure */
-flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS];
-static u32 pagesize;
-
-unsigned long flash_init(void)
-{
- at91_eefc_t *eefc = (at91_eefc_t *) ATMEL_BASE_EEFC;
- at91_dbu_t *dbu = (at91_dbu_t *) ATMEL_BASE_DBGU;
- u32 id, size, nplanes, planesize, nlocks;
- u32 addr, i, tmp=0;
-
- debug("eflash: init\n");
-
- flash_info[0].flash_id = FLASH_UNKNOWN;
-
- /* check if its an AT91ARM9XE SoC */
- if ((readl(&dbu->cidr) & AT91_DBU_CID_ARCH_MASK) != AT91_DBU_CID_ARCH_9XExx) {
- puts("eflash: not an AT91SAM9XE\n");
- return 0;
- }
-
- /* now query the eflash for its structure */
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_GETD, &eefc->fcr);
- while ((readl(&eefc->fsr) & AT91_EEFC_FSR_FRDY) == 0)
- ;
- id = readl(&eefc->frr); /* word 0 */
- size = readl(&eefc->frr); /* word 1 */
- pagesize = readl(&eefc->frr); /* word 2 */
- nplanes = readl(&eefc->frr); /* word 3 */
- planesize = readl(&eefc->frr); /* word 4 */
- debug("id=%08x size=%u pagesize=%u planes=%u planesize=%u\n",
- id, size, pagesize, nplanes, planesize);
- for (i=1; i<nplanes; i++) {
- tmp = readl(&eefc->frr); /* words 5..4+nplanes-1 */
- };
- nlocks = readl(&eefc->frr); /* word 4+nplanes */
- debug("nlocks=%u\n", nlocks);
- /* since we are going to use the lock regions as sectors, check count */
- if (nlocks > CONFIG_SYS_MAX_FLASH_SECT) {
- printf("eflash: number of lock regions(%u) "\
- "> CONFIG_SYS_MAX_FLASH_SECT. reducing...\n",
- nlocks);
- nlocks = CONFIG_SYS_MAX_FLASH_SECT;
- }
- flash_info[0].size = size;
- flash_info[0].sector_count = nlocks;
- flash_info[0].flash_id = id;
-
- addr = ATMEL_BASE_FLASH;
- for (i=0; i<nlocks; i++) {
- tmp = readl(&eefc->frr); /* words 4+nplanes+1.. */
- flash_info[0].start[i] = addr;
- flash_info[0].protect[i] = 0;
- addr += tmp;
- };
-
- /* now read the protection information for all regions */
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_GLB, &eefc->fcr);
- while ((readl(&eefc->fsr) & AT91_EEFC_FSR_FRDY) == 0)
- ;
- for (i=0; i<flash_info[0].sector_count; i++) {
- if (i%32 == 0)
- tmp = readl(&eefc->frr);
- flash_info[0].protect[i] = (tmp >> (i%32)) & 1;
-#if CONFIG_VAL(EFLASH_PROTSECTORS)
- if (i < CONFIG_EFLASH_PROTSECTORS)
- flash_info[0].protect[i] = 1;
-#endif
- }
-
- return size;
-}
-
-void flash_print_info(flash_info_t *info)
-{
- int i;
-
- puts("AT91SAM9XE embedded flash\n Size: ");
- print_size(info->size, " in ");
- printf("%d Sectors\n", info->sector_count);
-
- printf(" Sector Start Addresses:");
- for (i=0; i<info->sector_count; ++i) {
- if ((i % 5) == 0)
- printf("\n ");
- printf(" %08lX%s",
- info->start[i],
- info->protect[i] ? " (RO)" : " "
- );
- }
- printf ("\n");
- return;
-}
-
-int flash_real_protect (flash_info_t *info, long sector, int prot)
-{
- at91_eefc_t *eefc = (at91_eefc_t *) ATMEL_BASE_EEFC;
- u32 pagenum = (info->start[sector]-ATMEL_BASE_FLASH)/pagesize;
- u32 i, tmp=0;
-
- debug("protect sector=%ld prot=%d\n", sector, prot);
-
-#if CONFIG_VAL(EFLASH_PROTSECTORS)
- if (sector < CONFIG_EFLASH_PROTSECTORS) {
- if (!prot) {
- printf("eflash: sector %lu cannot be unprotected\n",
- sector);
- }
- return 1; /* return anyway, caller does not care for result */
- }
-#endif
- if (prot) {
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_SLB |
- (pagenum << AT91_EEFC_FCR_FARG_SHIFT), &eefc->fcr);
- } else {
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_CLB |
- (pagenum << AT91_EEFC_FCR_FARG_SHIFT), &eefc->fcr);
- }
- while ((readl(&eefc->fsr) & AT91_EEFC_FSR_FRDY) == 0)
- ;
- /* now re-read the protection information for all regions */
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_GLB, &eefc->fcr);
- while ((readl(&eefc->fsr) & AT91_EEFC_FSR_FRDY) == 0)
- ;
- for (i=0; i<info->sector_count; i++) {
- if (i%32 == 0)
- tmp = readl(&eefc->frr);
- info->protect[i] = (tmp >> (i%32)) & 1;
- }
- return 0;
-}
-
-static u32 erase_write_page (u32 pagenum)
-{
- at91_eefc_t *eefc = (at91_eefc_t *) ATMEL_BASE_EEFC;
-
- debug("erase+write page=%u\n", pagenum);
-
- /* give erase and write page command */
- writel(AT91_EEFC_FCR_KEY | AT91_EEFC_FCR_FCMD_EWP |
- (pagenum << AT91_EEFC_FCR_FARG_SHIFT), &eefc->fcr);
- while ((readl(&eefc->fsr) & AT91_EEFC_FSR_FRDY) == 0)
- ;
- /* return status */
- return readl(&eefc->fsr)
- & (AT91_EEFC_FSR_FCMDE | AT91_EEFC_FSR_FLOCKE);
-}
-
-int flash_erase(flash_info_t *info, int s_first, int s_last)
-{
- debug("erase first=%d last=%d\n", s_first, s_last);
- puts("this flash does not need and support erasing!\n");
- return 0;
-}
-
-/*
- * Copy memory to flash, returns:
- * 0 - OK
- * 1 - write timeout
- */
-
-int write_buff(flash_info_t *info, uchar *src, ulong addr, ulong cnt)
-{
- u32 pagenum;
- u32 *src32, *dst32;
- u32 i;
-
- debug("write src=%08lx addr=%08lx cnt=%lx\n",
- (ulong)src, addr, cnt);
-
- /* REQUIRE addr to be on a page start, abort if not */
- if (addr % pagesize) {
- printf ("eflash: start %08lx is not on page start\n"\
- " write aborted\n", addr);
- return 1;
- }
-
- /* now start copying data */
- pagenum = (addr-ATMEL_BASE_FLASH)/pagesize;
- src32 = (u32 *) src;
- dst32 = (u32 *) addr;
- while (cnt > 0) {
- i = pagesize / 4;
- /* fill page buffer */
- while (i--)
- *dst32++ = *src32++;
- /* write page */
- if (erase_write_page(pagenum))
- return 1;
- pagenum++;
- if (cnt > pagesize)
- cnt -= pagesize;
- else
- cnt = 0;
- }
- return 0;
-}
diff --git a/arch/arm/mach-at91/include/mach/at91_dbu.h b/arch/arm/mach-at91/include/mach/at91_dbu.h
deleted file mode 100644
index 91bb686bc10a..000000000000
--- a/arch/arm/mach-at91/include/mach/at91_dbu.h
+++ /dev/null
@@ -1,37 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2010
- * Reinhard Meyer, reinhard.meyer at emk-elektronik.de
- *
- * Debug Unit
- * Based on AT91SAM9XE datasheet
- */
-
-#ifndef AT91_DBU_H
-#define AT91_DBU_H
-
-#ifndef __ASSEMBLY__
-
-typedef struct at91_dbu {
- u32 cr; /* Control Register WO */
- u32 mr; /* Mode Register RW */
- u32 ier; /* Interrupt Enable Register WO */
- u32 idr; /* Interrupt Disable Register WO */
- u32 imr; /* Interrupt Mask Register RO */
- u32 sr; /* Status Register RO */
- u32 rhr; /* Receive Holding Register RO */
- u32 thr; /* Transmit Holding Register WO */
- u32 brgr; /* Baud Rate Generator Register RW */
- u32 res1[7];/* 0x0024 - 0x003C Reserved */
- u32 cidr; /* Chip ID Register RO */
- u32 exid; /* Chip ID Extension Register RO */
- u32 fnr; /* Force NTRST Register RW */
-} at91_dbu_t;
-
-#endif /* __ASSEMBLY__ */
-
-#define AT91_DBU_CID_ARCH_MASK 0x0ff00000
-#define AT91_DBU_CID_ARCH_9xx 0x01900000
-#define AT91_DBU_CID_ARCH_9XExx 0x02900000
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91_eefc.h b/arch/arm/mach-at91/include/mach/at91_eefc.h
deleted file mode 100644
index e7bb2bfecbad..000000000000
--- a/arch/arm/mach-at91/include/mach/at91_eefc.h
+++ /dev/null
@@ -1,47 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * Copyright (C) 2010
- * Reinhard Meyer, reinhard.meyer at emk-elektronik.de
- *
- * Enhanced Embedded Flash Controller
- * Based on AT91SAM9XE datasheet
- */
-
-#ifndef AT91_EEFC_H
-#define AT91_EEFC_H
-
-#ifndef __ASSEMBLY__
-
-typedef struct at91_eefc {
- u32 fmr; /* Flash Mode Register RW */
- u32 fcr; /* Flash Command Register WO */
- u32 fsr; /* Flash Status Register RO */
- u32 frr; /* Flash Result Register RO */
-} at91_eefc_t;
-
-#endif /* __ASSEMBLY__ */
-
-#define AT91_EEFC_FMR_FWS_MASK 0x00000f00
-#define AT91_EEFC_FMR_FRDY_BIT 0x00000001
-
-#define AT91_EEFC_FCR_KEY 0x5a000000
-#define AT91_EEFC_FCR_FARG_MASK 0x00ffff00
-#define AT91_EEFC_FCR_FARG_SHIFT 8
-#define AT91_EEFC_FCR_FCMD_GETD 0x0
-#define AT91_EEFC_FCR_FCMD_WP 0x1
-#define AT91_EEFC_FCR_FCMD_WPL 0x2
-#define AT91_EEFC_FCR_FCMD_EWP 0x3
-#define AT91_EEFC_FCR_FCMD_EWPL 0x4
-#define AT91_EEFC_FCR_FCMD_EA 0x5
-#define AT91_EEFC_FCR_FCMD_SLB 0x8
-#define AT91_EEFC_FCR_FCMD_CLB 0x9
-#define AT91_EEFC_FCR_FCMD_GLB 0xA
-#define AT91_EEFC_FCR_FCMD_SGPB 0xB
-#define AT91_EEFC_FCR_FCMD_CGPB 0xC
-#define AT91_EEFC_FCR_FCMD_GGPB 0xD
-
-#define AT91_EEFC_FSR_FRDY 1
-#define AT91_EEFC_FSR_FCMDE 2
-#define AT91_EEFC_FSR_FLOCKE 4
-
-#endif
diff --git a/arch/arm/mach-at91/include/mach/at91sam9260.h b/arch/arm/mach-at91/include/mach/at91sam9260.h
index 103db2695335..bdd46ee0eaed 100644
--- a/arch/arm/mach-at91/include/mach/at91sam9260.h
+++ b/arch/arm/mach-at91/include/mach/at91sam9260.h
@@ -7,7 +7,7 @@
* Reinhard Meyer, EMK Elektronik, reinhard.meyer at emk-elektronik.de
*
* Definitions for the SoCs:
- * AT91SAM9260, AT91SAM9G20, AT91SAM9XE
+ * AT91SAM9260, AT91SAM9G20
*
* Note that those SoCs are mostly software and pin compatible,
* therefore this file applies to all of them. Differences between
@@ -142,15 +142,7 @@
/*
* SoC specific defines
*/
-#if defined(CONFIG_AT91SAM9XE)
-# define ATMEL_CPU_NAME "AT91SAM9XE"
-# define ATMEL_ID_TWI1 25 /* TWI 1 */
-# define ATMEL_BASE_FLASH 0x00200000 /* Internal FLASH */
-# define ATMEL_BASE_SRAM 0x00300000 /* Internal SRAM */
-# define ATMEL_BASE_TWI1 0xfffd8000
-# define ATMEL_BASE_EEFC 0xfffffa00
-# define ATMEL_BASE_GPBR 0xfffffd60
-#elif defined(CONFIG_AT91SAM9260)
+#if defined(CONFIG_AT91SAM9260)
# define ATMEL_CPU_NAME "AT91SAM9260"
# define ATMEL_ID_USART5 25 /* USART 5 */
# define ATMEL_BASE_SRAM0 0x00200000 /* Internal SRAM 0 */
diff --git a/arch/arm/mach-at91/include/mach/hardware.h b/arch/arm/mach-at91/include/mach/hardware.h
index 0a16c8ff088b..988ef492b62f 100644
--- a/arch/arm/mach-at91/include/mach/hardware.h
+++ b/arch/arm/mach-at91/include/mach/hardware.h
@@ -9,8 +9,7 @@
#if defined(CONFIG_AT91RM9200)
# include <asm/arch/at91rm9200.h>
-#elif defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9G20) || \
- defined(CONFIG_AT91SAM9XE)
+#elif defined(CONFIG_AT91SAM9260) || defined(CONFIG_AT91SAM9G20)
# include <asm/arch/at91sam9260.h>
#elif defined(CONFIG_AT91SAM9261) || defined(CONFIG_AT91SAM9G10)
# include <asm/arch/at91sam9261.h>
diff --git a/board/egnite/ethernut5/Kconfig b/board/egnite/ethernut5/Kconfig
deleted file mode 100644
index 5a6c1c5de1fa..000000000000
--- a/board/egnite/ethernut5/Kconfig
+++ /dev/null
@@ -1,12 +0,0 @@
-if TARGET_ETHERNUT5
-
-config SYS_BOARD
- default "ethernut5"
-
-config SYS_VENDOR
- default "egnite"
-
-config SYS_CONFIG_NAME
- default "ethernut5"
-
-endif
diff --git a/board/egnite/ethernut5/MAINTAINERS b/board/egnite/ethernut5/MAINTAINERS
deleted file mode 100644
index a4ad913b630e..000000000000
--- a/board/egnite/ethernut5/MAINTAINERS
+++ /dev/null
@@ -1,6 +0,0 @@
-ETHERNUT5 BOARD
-M: egnite GmbH <info at egnite.de>
-S: Maintained
-F: board/egnite/ethernut5/
-F: include/configs/ethernut5.h
-F: configs/ethernut5_defconfig
diff --git a/board/egnite/ethernut5/Makefile b/board/egnite/ethernut5/Makefile
deleted file mode 100644
index 580f440564e1..000000000000
--- a/board/egnite/ethernut5/Makefile
+++ /dev/null
@@ -1,10 +0,0 @@
-# SPDX-License-Identifier: GPL-2.0+
-#
-# (C) Copyright 2003-2008
-# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-#
-# (C) Copyright 2010
-# egnite GmbH
-
-obj-y += ethernut5.o
-obj-y += ethernut5_pwrman.o
diff --git a/board/egnite/ethernut5/ethernut5.c b/board/egnite/ethernut5/ethernut5.c
deleted file mode 100644
index 64e341c3779c..000000000000
--- a/board/egnite/ethernut5/ethernut5.c
+++ /dev/null
@@ -1,198 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2011
- * egnite GmbH <info at egnite.de>
- *
- * (C) Copyright 2010
- * Ole Reinhardt <ole.reinhardt at thermotemp.de>
- */
-
-/*
- * Ethernut 5 general board support
- *
- * Ethernut is an open source hardware and software project for
- * embedded Ethernet devices. Hardware layouts and CAD files are
- * freely available under BSD-like license.
- *
- * Ethernut 5 is the first member of the Ethernut board family
- * with U-Boot and Linux support. This implementation is based
- * on the original work done by Ole Reinhardt, but heavily modified
- * to support additional features and the latest board revision 5.0F.
- *
- * Main board components are by default:
- *
- * Atmel AT91SAM9XE512 CPU with 512 kBytes NOR Flash
- * 2 x 64 MBytes Micron MT48LC32M16A2P SDRAM
- * 512 MBytes Micron MT29F4G08ABADA NAND Flash
- * 4 MBytes Atmel AT45DB321D DataFlash
- * SMSC LAN8710 Ethernet PHY
- * Atmel ATmega168 MCU used for power management
- * Linear Technology LTC4411 PoE controller
- *
- * U-Boot relevant board interfaces are:
- *
- * 100 Mbit Ethernet with IEEE 802.3af PoE
- * RS-232 serial port
- * USB host and device
- * MMC/SD-Card slot
- * Expansion port with I2C, SPI and more...
- *
- * Typically the U-Boot image is loaded from serial DataFlash into
- * SDRAM by the samboot boot loader, which is located in internal
- * NOR Flash and provides all essential initializations like CPU
- * and peripheral clocks and, of course, the SDRAM configuration.
- *
- * For testing purposes it is also possibly to directly transfer
- * the image into SDRAM via JTAG. A tested configuration exists
- * for the Turtelizer 2 hardware dongle and the OpenOCD software.
- * In this case the latter will do the basic hardware configuration
- * via its reset-init script.
- *
- * For additional information visit the project home page at
- * http://www.ethernut.de/
- */
-
-#include <config.h>
-#include <init.h>
-#include <net.h>
-#include <netdev.h>
-#include <miiphy.h>
-#include <i2c.h>
-#include <mmc.h>
-#include <atmel_mci.h>
-#include <asm/global_data.h>
-
-#include <asm/arch/at91sam9260.h>
-#include <asm/arch/at91sam9260_matrix.h>
-#include <asm/arch/at91sam9_smc.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/clk.h>
-#include <asm/arch/gpio.h>
-#include <asm/io.h>
-#include <asm/gpio.h>
-
-#include "ethernut5_pwrman.h"
-
-DECLARE_GLOBAL_DATA_PTR;
-
-/*
- * This is called last during early initialization. Most of the basic
- * hardware interfaces are up and running.
- *
- * The SDRAM hardware has been configured by the first stage boot loader.
- * We only need to announce its size, using u-boot's memory check.
- */
-int dram_init(void)
-{
- gd->ram_size = get_ram_size(
- (void *)CFG_SYS_SDRAM_BASE,
- CFG_SYS_SDRAM_SIZE);
- return 0;
-}
-
-#ifdef CONFIG_CMD_NAND
-static void ethernut5_nand_hw_init(void)
-{
- struct at91_smc *smc = (struct at91_smc *)ATMEL_BASE_SMC;
- struct at91_matrix *matrix = (struct at91_matrix *)ATMEL_BASE_MATRIX;
- unsigned long csa;
-
- /* Assign CS3 to NAND/SmartMedia Interface */
- csa = readl(&matrix->ebicsa);
- csa |= AT91_MATRIX_CS3A_SMC_SMARTMEDIA;
- writel(csa, &matrix->ebicsa);
-
- /* Configure SMC CS3 for NAND/SmartMedia */
- writel(AT91_SMC_SETUP_NWE(1) | AT91_SMC_SETUP_NCS_WR(0) |
- AT91_SMC_SETUP_NRD(1) | AT91_SMC_SETUP_NCS_RD(0),
- &smc->cs[3].setup);
- writel(AT91_SMC_PULSE_NWE(3) | AT91_SMC_PULSE_NCS_WR(3) |
- AT91_SMC_PULSE_NRD(3) | AT91_SMC_PULSE_NCS_RD(3),
- &smc->cs[3].pulse);
- writel(AT91_SMC_CYCLE_NWE(5) | AT91_SMC_CYCLE_NRD(5),
- &smc->cs[3].cycle);
- writel(AT91_SMC_MODE_RM_NRD | AT91_SMC_MODE_WM_NWE |
- AT91_SMC_MODE_EXNW_DISABLE |
- AT91_SMC_MODE_DBW_8 |
- AT91_SMC_MODE_TDF_CYCLE(2),
- &smc->cs[3].mode);
-
-#ifdef CFG_SYS_NAND_READY_PIN
- /* Ready pin is optional. */
- at91_set_pio_input(CFG_SYS_NAND_READY_PIN, 1);
-#endif
- gpio_direction_output(CFG_SYS_NAND_ENABLE_PIN, 1);
-}
-#endif
-
-/*
- * This is called first during late initialization.
- */
-int board_init(void)
-{
- at91_periph_clk_enable(ATMEL_ID_PIOA);
- at91_periph_clk_enable(ATMEL_ID_PIOB);
- at91_periph_clk_enable(ATMEL_ID_PIOC);
-
- /* Set adress of boot parameters. */
- gd->bd->bi_boot_params = CFG_SYS_SDRAM_BASE + 0x100;
- /* Initialize UARTs and power management. */
- ethernut5_power_init();
-#ifdef CONFIG_CMD_NAND
- ethernut5_nand_hw_init();
-#endif
- return 0;
-}
-
-#ifdef CONFIG_MACB
-/*
- * This is optionally called last during late initialization.
- */
-int board_eth_init(struct bd_info *bis)
-{
- const char *devname;
- unsigned short mode;
-
- at91_periph_clk_enable(ATMEL_ID_EMAC0);
-
- /* Need to reset PHY via power management. */
- ethernut5_phy_reset();
- /* Set peripheral pins. */
- at91_macb_hw_init();
- /* Basic EMAC initialization. */
- if (macb_eth_initialize(0, (void *)ATMEL_BASE_EMAC0, CFG_PHY_ID))
- return -1;
- /*
- * Early board revisions have a pull-down at the PHY's MODE0
- * strap pin, which forces the PHY into power down. Here we
- * switch to all-capable mode.
- */
- devname = miiphy_get_current_dev();
- if (miiphy_read(devname, 0, 18, &mode) == 0) {
- /* Set mode[2:0] to 0b111. */
- mode |= 0x00E0;
- miiphy_write(devname, 0, 18, mode);
- /* Soft reset overrides strap pins. */
- miiphy_write(devname, 0, MII_BMCR, BMCR_RESET);
- }
- /* Sync environment with network devices, needed for nfsroot. */
- return eth_init();
-}
-#endif
-
-#ifdef CONFIG_GENERIC_ATMEL_MCI
-int board_mmc_init(struct bd_info *bd)
-{
- at91_periph_clk_enable(ATMEL_ID_MCI);
-
- /* Initialize MCI hardware. */
- at91_mci_hw_init();
- /* Register the device. */
- return atmel_mci_init((void *)ATMEL_BASE_MCI);
-}
-
-int board_mmc_getcd(struct mmc *mmc)
-{
- return !at91_get_pio_value(CFG_SYS_MMC_CD_PIN);
-}
-#endif
diff --git a/board/egnite/ethernut5/ethernut5_pwrman.c b/board/egnite/ethernut5/ethernut5_pwrman.c
deleted file mode 100644
index 42e1914a8759..000000000000
--- a/board/egnite/ethernut5/ethernut5_pwrman.c
+++ /dev/null
@@ -1,323 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0+
-/*
- * (C) Copyright 2011
- * egnite GmbH <info at egnite.de>
- */
-
-/*
- * Ethernut 5 power management support
- *
- * This board may be supplied via USB, IEEE 802.3af PoE or an
- * auxiliary DC input. An on-board ATmega168 microcontroller,
- * the so called power management controller or PMC, is used
- * to select the supply source and to switch on and off certain
- * energy consuming board components. This allows to reduce the
- * total stand-by consumption to less than 70mW.
- *
- * The main CPU communicates with the PMC via I2C. When
- * CONFIG_CMD_BSP is defined in the board configuration file,
- * then the board specific command 'pwrman' becomes available,
- * which allows to manually deal with the PMC.
- *
- * Two distinct registers are provided by the PMC for enabling
- * and disabling specific features. This avoids the often seen
- * read-modify-write cycle or shadow register requirement.
- * Additional registers are available to query the board
- * status and temperature, the auxiliary voltage and to control
- * the green user LED that is integrated in the reset switch.
- *
- * Note, that the AVR firmware of the PMC is released under BSDL.
- *
- * For additional information visit the project home page at
- * http://www.ethernut.de/
- */
-#include <command.h>
-#include <vsprintf.h>
-#include <asm/arch/at91sam9260.h>
-#include <asm/arch/at91_common.h>
-#include <asm/arch/gpio.h>
-#include <asm/io.h>
-#include <i2c.h>
-#include <linux/delay.h>
-
-#include "ethernut5_pwrman.h"
-
-/* PMC firmware version */
-static int pwrman_major;
-static int pwrman_minor;
-
-/*
- * Enable Ethernut 5 power management.
- *
- * This function must be called during board initialization.
- * While we are using u-boot's I2C subsystem, it may be required
- * to enable the serial port before calling this function,
- * in particular when debugging is enabled.
- *
- * If board specific commands are not available, we will activate
- * all board components.
- */
-void ethernut5_power_init(void)
-{
- pwrman_minor = i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_VERS);
- pwrman_major = pwrman_minor >> 4;
- pwrman_minor &= 15;
-
-#ifndef CONFIG_CMD_BSP
- /* Do not modify anything, if we do not have a known version. */
- if (pwrman_major == 2) {
- /* Without board specific commands we enable all features. */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_ENA, ~PWRMAN_ETHRST);
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_DIS, PWRMAN_ETHRST);
- }
-#endif
-}
-
-/*
- * Reset Ethernet PHY.
- *
- * This function allows the re-configure the PHY after
- * changing its strap pins.
- */
-void ethernut5_phy_reset(void)
-{
- /* Do not modify anything, if we do not have a known version. */
- if (pwrman_major != 2)
- return;
-
- /*
- * Make sure that the Ethernet clock is enabled and the PHY reset
- * is disabled for at least 100 us.
- */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_ENA, PWRMAN_ETHCLK);
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_DIS, PWRMAN_ETHRST);
- udelay(100);
-
- /*
- * LAN8710 strap pins are
- * PA14 => PHY MODE0
- * PA15 => PHY MODE1
- * PA17 => PHY MODE2 => 111b all capable
- * PA18 => PHY ADDR0 => 0b
- */
- at91_set_pio_input(AT91_PIO_PORTA, 14, 1);
- at91_set_pio_input(AT91_PIO_PORTA, 15, 1);
- at91_set_pio_input(AT91_PIO_PORTA, 17, 1);
- at91_set_pio_input(AT91_PIO_PORTA, 18, 0);
-
- /* Activate PHY reset for 100 us. */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_ENA, PWRMAN_ETHRST);
- udelay(100);
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_DIS, PWRMAN_ETHRST);
-
- at91_set_pio_input(AT91_PIO_PORTA, 14, 1);
-}
-
-/*
- * Output the firmware version we got during initialization.
- */
-void ethernut5_print_version(void)
-{
- printf("%u.%u\n", pwrman_major, pwrman_minor);
-}
-
-/*
- * All code below this point is optional and implements
- * the 'pwrman' command.
- */
-#ifdef CONFIG_CMD_BSP
-
-/* Human readable names of PMC features */
-char *pwrman_feat[8] = {
- "board", "vbin", "vbout", "mmc",
- "rs232", "ethclk", "ethrst", "wakeup"
-};
-
-/*
- * Print all feature names, that have its related flags enabled.
- */
-static void print_flagged_features(u8 flags)
-{
- int i;
-
- for (i = 0; i < 8; i++) {
- if (flags & (1 << i))
- printf("%s ", pwrman_feat[i]);
- }
-}
-
-/*
- * Return flags of a given list of feature names.
- *
- * The function stops at the first unknown list entry and
- * returns the number of detected names as a function result.
- */
-static int feature_flags(char * const names[], int num, u8 *flags)
-{
- int i, j;
-
- *flags = 0;
- for (i = 0; i < num; i++) {
- for (j = 0; j < 8; j++) {
- if (strcmp(pwrman_feat[j], names[i]) == 0) {
- *flags |= 1 << j;
- break;
- }
- }
- if (j > 7)
- break;
- }
- return i;
-}
-
-void ethernut5_print_power(void)
-{
- u8 flags;
- int i;
-
- flags = i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_ENA);
- for (i = 0; i < 2; i++) {
- if (flags) {
- print_flagged_features(flags);
- printf("%s\n", i ? "off" : "on");
- }
- flags = ~flags;
- }
-}
-
-void ethernut5_print_celsius(void)
-{
- int val;
-
- /* Read ADC value from LM50 and return Celsius degrees. */
- val = i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_TEMP);
- val *= 5000; /* 100mV/degree with 5V reference */
- val += 128; /* 8 bit resolution */
- val /= 256;
- val -= 450; /* Celsius offset, still x10 */
- /* Output full degrees. */
- printf("%d\n", (val + 5) / 10);
-}
-
-void ethernut5_print_voltage(void)
-{
- int val;
-
- /* Read ADC value from divider and return voltage. */
- val = i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_VAUX);
- /* Resistors are 100k and 12.1k */
- val += 5;
- val *= 180948;
- val /= 100000;
- val++;
- /* Calculation was done in 0.1V units. */
- printf("%d\n", (val + 5) / 10);
-}
-
-/*
- * Process the board specific 'pwrman' command.
- */
-int do_pwrman(struct cmd_tbl *cmdtp, int flag, int argc, char *const argv[])
-{
- u8 val;
- int i;
-
- if (argc == 1) {
- ethernut5_print_power();
- } else if (argc == 2 && strcmp(argv[1], "reset") == 0) {
- at91_set_pio_output(AT91_PIO_PORTB, 8, 1);
- udelay(100);
- at91_set_pio_output(AT91_PIO_PORTB, 8, 0);
- udelay(100000);
- } else if (argc == 2 && strcmp(argv[1], "temp") == 0) {
- ethernut5_print_celsius();
- } else if (argc == 2 && strcmp(argv[1], "vaux") == 0) {
- ethernut5_print_voltage();
- } else if (argc == 2 && strcmp(argv[1], "version") == 0) {
- ethernut5_print_version();
- } else if (strcmp(argv[1], "led") == 0) {
- /* Control the green status LED. Blink frequency unit
- ** is 0.1s, very roughly. */
- if (argc == 2) {
- /* No more arguments, output current settings. */
- val = i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_LEDCTL);
- printf("led %u %u\n", val >> 4, val & 15);
- } else {
- /* First argument specifies the on-time. */
- val = (u8) simple_strtoul(argv[2], NULL, 0);
- val <<= 4;
- if (argc > 3) {
- /* Second argument specifies the off-time. */
- val |= (u8) (simple_strtoul(argv[3], NULL, 0)
- & 15);
- }
- /* Update the LED control register. */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_LEDCTL, val);
- }
- } else {
- /* We expect a list of features followed an optional status. */
- argc--;
- i = feature_flags(&argv[1], argc, &val);
- if (argc == i) {
- /* We got a list only, print status. */
- val &= i2c_reg_read(PWRMAN_I2C_ADDR, PWRMAN_REG_STA);
- if (val) {
- if (i > 1)
- print_flagged_features(val);
- printf("active\n");
- } else {
- printf("inactive\n");
- }
- } else {
- /* More arguments. */
- if (i == 0) {
- /* No given feature, use despensibles. */
- val = PWRMAN_DISPENSIBLE;
- }
- if (strcmp(argv[i + 1], "on") == 0) {
- /* Enable features. */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_ENA,
- val);
- } else if (strcmp(argv[i + 1], "off") == 0) {
- /* Disable features. */
- i2c_reg_write(PWRMAN_I2C_ADDR, PWRMAN_REG_DIS,
- val);
- } else {
- printf("Bad parameter %s\n", argv[i + 1]);
- return 1;
- }
- }
- }
- return 0;
-}
-
-U_BOOT_CMD(
- pwrman, CONFIG_SYS_MAXARGS, 1, do_pwrman,
- "power management",
- "- print settings\n"
- "pwrman feature ...\n"
- " - print status\n"
- "pwrman [feature ...] on|off\n"
- " - enable/disable specified or all dispensible features\n"
- "pwrman led [on-time [off-time]]\n"
- " - print or set led blink timer\n"
- "pwrman temp\n"
- " - print board temperature (Celsius)\n"
- "pwrman vaux\n"
- " - print auxiliary input voltage\n"
- "pwrman reset\n"
- " - reset power management controller\n"
- "pwrman version\n"
- " - print firmware version\n"
- "\n"
- " features, (*)=dispensible:\n"
- " board - 1.8V and 3.3V supply\n"
- " vbin - supply via USB device connector\n"
- " vbout - USB host connector supply(*)\n"
- " mmc - MMC slot supply(*)\n"
- " rs232 - RS232 driver\n"
- " ethclk - Ethernet PHY clock(*)\n"
- " ethrst - Ethernet PHY reset\n"
- " wakeup - RTC alarm"
-);
-#endif /* CONFIG_CMD_BSP */
diff --git a/board/egnite/ethernut5/ethernut5_pwrman.h b/board/egnite/ethernut5/ethernut5_pwrman.h
deleted file mode 100644
index 103f5583289c..000000000000
--- a/board/egnite/ethernut5/ethernut5_pwrman.h
+++ /dev/null
@@ -1,51 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011
- * egnite GmbH <info at egnite.de>
- */
-
-/*
- * Ethernut 5 power management support
- *
- * For additional information visit the project home page at
- * http://www.ethernut.de/
- */
-
-/* I2C address of the PMC */
-#define PWRMAN_I2C_ADDR 0x22
-
-/* PMC registers */
-#define PWRMAN_REG_VERS 0 /* Version register */
-#define PWRMAN_REG_STA 1 /* Feature status register */
-#define PWRMAN_REG_ENA 2 /* Feature enable register */
-#define PWRMAN_REG_DIS 3 /* Feature disable register */
-#define PWRMAN_REG_TEMP 4 /* Board temperature */
-#define PWRMAN_REG_VAUX 6 /* Auxiliary input voltage */
-#define PWRMAN_REG_LEDCTL 8 /* LED blinking timer. */
-
-/* Feature flags used in status, enable and disable registers */
-#define PWRMAN_BOARD 0x01 /* 1.8V and 3.3V supply */
-#define PWRMAN_VBIN 0x02 /* VBUS input at device connector */
-#define PWRMAN_VBOUT 0x04 /* VBUS output at host connector */
-#define PWRMAN_MMC 0x08 /* Memory card supply */
-#define PWRMAN_RS232 0x10 /* RS-232 driver shutdown */
-#define PWRMAN_ETHCLK 0x20 /* Ethernet clock enable */
-#define PWRMAN_ETHRST 0x40 /* Ethernet PHY reset */
-#define PWRMAN_WAKEUP 0x80 /* RTC wake-up */
-
-/* Features, which are not essential to keep u-boot alive */
-#define PWRMAN_DISPENSIBLE (PWRMAN_VBOUT | PWRMAN_MMC | PWRMAN_ETHCLK)
-
-/* Enable Ethernut 5 power management. */
-extern void ethernut5_power_init(void);
-
-/* Reset Ethernet PHY. */
-extern void ethernut5_phy_reset(void);
-
-extern void ethernut5_print_version(void);
-
-#ifdef CONFIG_CMD_BSP
-extern void ethernut5_print_power(void);
-extern void ethernut5_print_celsius(void);
-extern void ethernut5_print_voltage(void);
-#endif
diff --git a/configs/ethernut5_defconfig b/configs/ethernut5_defconfig
deleted file mode 100644
index 004f18661624..000000000000
--- a/configs/ethernut5_defconfig
+++ /dev/null
@@ -1,87 +0,0 @@
-CONFIG_ARM=y
-CONFIG_SKIP_LOWLEVEL_INIT=y
-CONFIG_ARCH_CPU_INIT=y
-CONFIG_ARCH_AT91=y
-CONFIG_TEXT_BASE=0x27000000
-CONFIG_SYS_MALLOC_LEN=0x121000
-CONFIG_TARGET_ETHERNUT5=y
-CONFIG_AT91_EFLASH=y
-CONFIG_EFLASH_PROTSECTORS=1
-CONFIG_NR_DRAM_BANKS=1
-CONFIG_ENV_SIZE=0x21000
-CONFIG_ENV_OFFSET=0x3DE000
-CONFIG_ENV_SECT_SIZE=0x21000
-CONFIG_DM_GPIO=y
-CONFIG_DEFAULT_DEVICE_TREE="ethernut5"
-CONFIG_SYS_LOAD_ADDR=0x020000000
-CONFIG_BOOTDELAY=3
-CONFIG_USE_BOOTARGS=y
-CONFIG_BOOTARGS="console=ttyS0,115200 root=/dev/mtdblock0 mtdparts=atmel_nand:-(root) rw rootfstype=jffs2"
-CONFIG_USE_BOOTCOMMAND=y
-CONFIG_BOOTCOMMAND="sf probe 0:0; sf read 0x22000000 0xc6000 0x294000; bootm 0x22000000"
-CONFIG_SYS_CBSIZE=256
-CONFIG_SYS_PBSIZE=281
-# CONFIG_DISPLAY_BOARDINFO is not set
-CONFIG_HUSH_PARSER=y
-# CONFIG_AUTO_COMPLETE is not set
-CONFIG_SYS_PROMPT="U-Boot> "
-# CONFIG_CMD_BDI is not set
-CONFIG_CMD_IMLS=y
-CONFIG_CMD_ASKENV=y
-CONFIG_CMD_UNZIP=y
-CONFIG_CMD_I2C=y
-# CONFIG_CMD_LOADS is not set
-CONFIG_CMD_MMC=y
-CONFIG_CMD_NAND=y
-CONFIG_CMD_SPI=y
-CONFIG_CMD_DHCP=y
-CONFIG_BOOTP_BOOTFILESIZE=y
-CONFIG_CMD_RARP=y
-CONFIG_SYS_DISABLE_AUTOLOAD=y
-CONFIG_CMD_MII=y
-# CONFIG_CMD_MDIO is not set
-CONFIG_CMD_PING=y
-CONFIG_CMD_CDP=y
-CONFIG_CMD_SNTP=y
-CONFIG_CMD_DNS=y
-CONFIG_CMD_BSP=y
-CONFIG_CMD_CACHE=y
-CONFIG_CMD_EXT2=y
-CONFIG_CMD_FAT=y
-CONFIG_CMD_JFFS2=y
-CONFIG_CMD_MTDPARTS=y
-CONFIG_MTDIDS_DEFAULT="nand0=atmel_nand"
-CONFIG_MTDPARTS_DEFAULT="mtdparts=atmel_nand:-(root)"
-CONFIG_CMD_UBI=y
-CONFIG_OF_CONTROL=y
-CONFIG_ENV_IS_IN_SPI_FLASH=y
-CONFIG_ENV_SPI_MAX_HZ=15000000
-CONFIG_SYS_RELOC_GD_ENV_ADDR=y
-CONFIG_NET_RETRY_COUNT=20
-CONFIG_CLK=y
-CONFIG_CLK_AT91=y
-CONFIG_AT91_GPIO=y
-CONFIG_SYS_I2C_LEGACY=y
-CONFIG_SYS_I2C_SOFT=y
-CONFIG_SYS_I2C_SOFT_SLAVE=0
-CONFIG_GENERIC_ATMEL_MCI=y
-CONFIG_MTD=y
-CONFIG_MTD_NOR_FLASH=y
-CONFIG_SYS_MAX_FLASH_SECT=32
-CONFIG_MTD_RAW_NAND=y
-# CONFIG_SYS_NAND_USE_FLASH_BBT is not set
-CONFIG_NAND_ATMEL=y
-CONFIG_DM_SPI_FLASH=y
-CONFIG_SPI_FLASH_ATMEL=y
-CONFIG_SPI_FLASH_DATAFLASH=y
-CONFIG_MACB=y
-CONFIG_RMII=y
-CONFIG_PINCTRL=y
-CONFIG_PINCTRL_AT91=y
-CONFIG_RTC_PCF8563=y
-CONFIG_DM_SERIAL=y
-CONFIG_ATMEL_USART=y
-CONFIG_SPI=y
-CONFIG_DM_SPI=y
-CONFIG_USB=y
-CONFIG_JFFS2_NAND=y
diff --git a/doc/board/atmel/at91ek.rst b/doc/board/atmel/at91ek.rst
index 6185b1dfb289..a500b2f8950c 100644
--- a/doc/board/atmel/at91ek.rst
+++ b/doc/board/atmel/at91ek.rst
@@ -6,8 +6,8 @@ AT91 Evaluation kits
Board mapping & boot media
--------------------------
-AT91SAM9260EK, AT91SAM9G20EK & AT91SAM9XEEK
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+AT91SAM9260EK & AT91SAM9G20EK
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
Memory map::
diff --git a/drivers/bootcount/Kconfig b/drivers/bootcount/Kconfig
index 2105cea3d45e..b6ab31a314a7 100644
--- a/drivers/bootcount/Kconfig
+++ b/drivers/bootcount/Kconfig
@@ -13,7 +13,6 @@ if BOOTCOUNT_LIMIT
choice
prompt "Boot count device"
default BOOTCOUNT_AM33XX if AM33XX || SOC_DA8XX
- default BOOTCOUNT_AT91 if AT91SAM9XE
default BOOTCOUNT_GENERIC
config BOOTCOUNT_GENERIC
diff --git a/include/configs/at91sam9260ek.h b/include/configs/at91sam9260ek.h
index b9cc7ba974de..b75db7e7bac0 100644
--- a/include/configs/at91sam9260ek.h
+++ b/include/configs/at91sam9260ek.h
@@ -35,11 +35,7 @@
#define CFG_SYS_SDRAM_SIZE 0x04000000
#define CFG_SYS_INIT_RAM_SIZE (16 * 1024)
-#ifdef CONFIG_AT91SAM9XE
-# define CFG_SYS_INIT_RAM_ADDR ATMEL_BASE_SRAM
-#else
-# define CFG_SYS_INIT_RAM_ADDR ATMEL_BASE_SRAM1
-#endif
+#define CFG_SYS_INIT_RAM_ADDR ATMEL_BASE_SRAM1
/* NAND flash */
#ifdef CONFIG_CMD_NAND
diff --git a/include/configs/ethernut5.h b/include/configs/ethernut5.h
deleted file mode 100644
index c327bbbe07d0..000000000000
--- a/include/configs/ethernut5.h
+++ /dev/null
@@ -1,88 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0+ */
-/*
- * (C) Copyright 2011
- * egnite GmbH <info at egnite.de>
- *
- * Configuation settings for Ethernut 5 with AT91SAM9XE.
- */
-
-#ifndef __CONFIG_H
-#define __CONFIG_H
-
-#include <asm/hardware.h>
-
-/* The first stage boot loader expects u-boot running at this address. */
-
-/* The first stage boot loader takes care of low level initialization. */
-
-/* CPU information */
-
-/* ARM asynchronous clock */
-#define CFG_SYS_AT91_SLOW_CLOCK 32768 /* slow clock xtal */
-#define CFG_SYS_AT91_MAIN_CLOCK 18432000 /* 18.432 MHz crystal */
-
-/* 32kB internal SRAM */
-#define CFG_SYS_INIT_RAM_ADDR 0x00300000 /*AT91SAM9XE_SRAM_BASE */
-#define CFG_SYS_INIT_RAM_SIZE (32 << 10)
-
-/* 128MB SDRAM in 1 bank */
-#define CFG_SYS_SDRAM_BASE 0x20000000
-#define CFG_SYS_SDRAM_SIZE (128 << 20)
-
-/* 512kB on-chip NOR flash */
-# define CFG_SYS_FLASH_BASE 0x00200000 /* AT91SAM9XE_FLASH_BASE */
-
-/* bootstrap + u-boot + env + linux in dataflash on CS0 */
-
-/* NAND flash */
-#ifdef CONFIG_CMD_NAND
-#define CFG_SYS_NAND_BASE 0x40000000
-/* our ALE is AD21 */
-#define CFG_SYS_NAND_MASK_ALE (1 << 21)
-/* our CLE is AD22 */
-#define CFG_SYS_NAND_MASK_CLE (1 << 22)
-#define CFG_SYS_NAND_ENABLE_PIN GPIO_PIN_PC(14)
-#endif
-
-/* JFFS2 */
-
-/* Ethernet */
-#define CFG_PHY_ID 0
-
-/* MMC */
-#ifdef CONFIG_CMD_MMC
-#define CFG_SYS_MMC_CD_PIN AT91_PIO_PORTC, 8
-#endif
-
-/* RTC */
-#if defined(CONFIG_CMD_DATE) || defined(CONFIG_CMD_SNTP)
-#define CFG_SYS_I2C_RTC_ADDR 0x51
-#endif
-
-#define I2C_SOFT_DECLARATIONS
-
-#define GPIO_I2C_SCL AT91_PIO_PORTA, 24
-#define GPIO_I2C_SDA AT91_PIO_PORTA, 23
-
-#define I2C_INIT { \
- at91_set_pio_periph(AT91_PIO_PORTA, 23, 0); \
- at91_set_pio_multi_drive(AT91_PIO_PORTA, 23, 1); \
- at91_set_pio_periph(AT91_PIO_PORTA, 24, 0); \
- at91_set_pio_output(AT91_PIO_PORTA, 24, 0); \
- at91_set_pio_multi_drive(AT91_PIO_PORTA, 24, 1); \
-}
-
-#define I2C_ACTIVE at91_set_pio_output(AT91_PIO_PORTA, 23, 0)
-#define I2C_TRISTATE at91_set_pio_input(AT91_PIO_PORTA, 23, 0)
-#define I2C_SCL(bit) at91_set_pio_value(AT91_PIO_PORTA, 24, bit)
-#define I2C_SDA(bit) at91_set_pio_value(AT91_PIO_PORTA, 23, bit)
-#define I2C_DELAY udelay(100)
-#define I2C_READ at91_get_pio_value(AT91_PIO_PORTA, 23)
-
-/* File systems */
-
-/* Boot command */
-
-/* Misc. u-boot settings */
-
-#endif
--
2.34.1
More information about the U-Boot
mailing list