[PATCH v3 30/33] global: Rename SPL_ to XPL_
Simon Glass
sjg at chromium.org
Mon Sep 30 03:49:53 CEST 2024
Use XPL_ as the symbol to indicate an SPL build. This means that SPL_ is
no-longer set.
Signed-off-by: Simon Glass <sjg at chromium.org>
---
(no changes since v1)
Makefile | 4 +--
arch/arm/config.mk | 6 ++--
arch/arm/cpu/arm920t/Makefile | 2 +-
arch/arm/cpu/arm926ejs/Makefile | 2 +-
arch/arm/cpu/armv7/Makefile | 2 +-
arch/arm/cpu/armv8/Makefile | 4 +--
arch/arm/lib/Makefile | 2 +-
arch/arm/mach-at91/arm926ejs/Makefile | 2 +-
arch/arm/mach-imx/Makefile | 2 +-
arch/arm/mach-omap2/am33xx/Makefile | 2 +-
arch/arm/mach-orion5x/Makefile | 4 +--
arch/arm/mach-stm32mp/stm32mp1/Makefile | 2 +-
arch/arm/mach-tegra/Makefile | 2 +-
arch/arm/mach-tegra/tegra20/Makefile | 2 +-
arch/arm/mach-tegra/tegra30/Makefile | 2 +-
arch/arm/mach-zynqmp/Makefile | 2 +-
arch/riscv/Makefile | 2 +-
arch/riscv/lib/Makefile | 8 ++---
arch/x86/Makefile | 2 +-
arch/x86/cpu/Makefile | 12 +++----
arch/x86/cpu/intel_common/Makefile | 4 +--
arch/x86/cpu/ivybridge/Makefile | 6 ++--
arch/x86/cpu/qemu/Makefile | 2 +-
arch/x86/lib/Makefile | 4 +--
board/bosch/guardian/Makefile | 2 +-
board/freescale/common/Makefile | 4 +--
board/st/common/Makefile | 2 +-
board/tcl/sl50/Makefile | 2 +-
board/ti/am335x/Makefile | 2 +-
board/ti/am43xx/Makefile | 2 +-
board/vscom/baltos/Makefile | 2 +-
board/xilinx/zynqmp/Makefile | 2 +-
boot/Makefile | 2 +-
cmd/Makefile | 2 +-
doc/develop/tests_writing.rst | 6 ++--
drivers/Makefile | 14 ++++----
drivers/ata/Makefile | 2 +-
drivers/block/Makefile | 2 +-
drivers/bus/Makefile | 2 +-
drivers/core/Makefile | 6 ++--
drivers/ddr/altera/Makefile | 2 +-
drivers/dfu/Makefile | 16 ++++-----
drivers/firmware/Makefile | 2 +-
drivers/gpio/Makefile | 8 ++---
drivers/i2c/Makefile | 16 ++++-----
drivers/led/Makefile | 2 +-
drivers/mailbox/Makefile | 2 +-
drivers/misc/Makefile | 10 +++---
drivers/mmc/Makefile | 6 ++--
drivers/mux/Makefile | 2 +-
drivers/nvme/Makefile | 2 +-
drivers/phy/Makefile | 6 ++--
drivers/phy/cadence/Makefile | 4 +--
drivers/phy/ti/Makefile | 2 +-
drivers/pinctrl/Makefile | 8 ++---
drivers/power/domain/Makefile | 2 +-
drivers/power/pmic/Makefile | 30 ++++++++--------
drivers/power/regulator/Makefile | 46 ++++++++++++-------------
drivers/remoteproc/Makefile | 2 +-
drivers/serial/Makefile | 2 +-
drivers/timer/Makefile | 8 ++---
drivers/usb/cdns3/Makefile | 4 +--
drivers/usb/common/Makefile | 2 +-
drivers/usb/dwc3/Makefile | 4 +--
drivers/usb/gadget/udc/Makefile | 4 +--
drivers/usb/host/Makefile | 2 +-
drivers/video/Makefile | 2 +-
drivers/video/tidss/Makefile | 2 +-
fs/fat/Makefile | 4 +--
fs/squashfs/Makefile | 2 +-
lib/Makefile | 28 +++++++--------
lib/acpi/Makefile | 8 ++---
lib/aes/Makefile | 2 +-
lib/crypto/Makefile | 14 ++++----
lib/ecdsa/Makefile | 2 +-
net/Makefile | 6 ++--
scripts/Kbuild.include | 4 +--
scripts/Makefile.xpl | 4 +--
test/Makefile | 22 ++++++------
test/fuzz/Makefile | 2 +-
tools/qconfig.py | 6 ++--
81 files changed, 219 insertions(+), 219 deletions(-)
diff --git a/Makefile b/Makefile
index 4378993ccfd..d38adcbd1e6 100644
--- a/Makefile
+++ b/Makefile
@@ -829,7 +829,7 @@ KBUILD_HOSTCFLAGS += $(if $(CONFIG_TOOLS_DEBUG),-g)
UBOOTINCLUDE := \
-Iinclude \
$(if $(KBUILD_SRC), -I$(srctree)/include) \
- $(if $(CONFIG_$(SPL_)SYS_THUMB_BUILD), \
+ $(if $(CONFIG_$(XPL_)SYS_THUMB_BUILD), \
$(if $(CONFIG_HAS_THUMB2), \
$(if $(CONFIG_CPU_V7M), \
-I$(srctree)/arch/arm/thumb1/include), \
@@ -864,7 +864,7 @@ libs-y += disk/
libs-y += drivers/
libs-$(CONFIG_SYS_FSL_DDR) += drivers/ddr/fsl/
libs-$(CONFIG_SYS_FSL_MMDC) += drivers/ddr/fsl/
-libs-$(CONFIG_$(SPL_)ALTERA_SDRAM) += drivers/ddr/altera/
+libs-$(CONFIG_$(XPL_)ALTERA_SDRAM) += drivers/ddr/altera/
libs-y += drivers/usb/cdns3/
libs-y += drivers/usb/dwc3/
libs-y += drivers/usb/common/
diff --git a/arch/arm/config.mk b/arch/arm/config.mk
index 084fd399931..e0045e22271 100644
--- a/arch/arm/config.mk
+++ b/arch/arm/config.mk
@@ -40,7 +40,7 @@ PLATFORM_ELFFLAGS += -B arm -O elf32-littlearm
endif
# Choose between ARM/Thumb instruction sets
-ifeq ($(CONFIG_$(SPL_)SYS_THUMB_BUILD),y)
+ifeq ($(CONFIG_$(XPL_)SYS_THUMB_BUILD),y)
AFLAGS_IMPLICIT_IT := $(call as-option,-Wa$(comma)-mimplicit-it=always)
PF_CPPFLAGS_ARM := $(AFLAGS_IMPLICIT_IT) \
$(call cc-option, -mthumb -mthumb-interwork,\
@@ -53,7 +53,7 @@ PF_CPPFLAGS_ARM := $(call cc-option,-marm,) \
endif
# Only test once
-ifeq ($(CONFIG_$(SPL_)SYS_THUMB_BUILD),y)
+ifeq ($(CONFIG_$(XPL_)SYS_THUMB_BUILD),y)
archprepare: checkthumb checkgcc6
checkthumb:
@@ -116,7 +116,7 @@ LDFLAGS_u-boot += -pie
#
# http://sourceware.org/bugzilla/show_bug.cgi?id=12532
#
-ifeq ($(CONFIG_$(SPL_)SYS_THUMB_BUILD),y)
+ifeq ($(CONFIG_$(XPL_)SYS_THUMB_BUILD),y)
ifeq ($(GAS_BUG_12532),)
export GAS_BUG_12532:=$(shell if [ $(call binutils-version) -lt 0222 ] ; \
then echo y; else echo n; fi)
diff --git a/arch/arm/cpu/arm920t/Makefile b/arch/arm/cpu/arm920t/Makefile
index 5ac3740621c..06456fe5a81 100644
--- a/arch/arm/cpu/arm920t/Makefile
+++ b/arch/arm/cpu/arm920t/Makefile
@@ -9,6 +9,6 @@ obj-y += cpu.o
# some files can only build in ARM mode
-ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
+ifdef CONFIG_$(XPL_)SYS_THUMB_BUILD
CFLAGS_cpu.o := -marm
endif
diff --git a/arch/arm/cpu/arm926ejs/Makefile b/arch/arm/cpu/arm926ejs/Makefile
index 75513889c5d..750cb94dc6e 100644
--- a/arch/arm/cpu/arm926ejs/Makefile
+++ b/arch/arm/cpu/arm926ejs/Makefile
@@ -17,7 +17,7 @@ obj-$(CONFIG_ARCH_SUNXI) += sunxi/
# some files can only build in ARM or THUMB2, not THUMB1
-ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
+ifdef CONFIG_$(XPL_)SYS_THUMB_BUILD
ifndef CONFIG_HAS_THUMB2
CFLAGS_cpu.o := -marm
diff --git a/arch/arm/cpu/armv7/Makefile b/arch/arm/cpu/armv7/Makefile
index 0e7d769bd40..6461f5f5bde 100644
--- a/arch/arm/cpu/armv7/Makefile
+++ b/arch/arm/cpu/armv7/Makefile
@@ -17,7 +17,7 @@ obj-$(CONFIG_EFI_LOADER) += sctlr.o
obj-$(CONFIG_ARMV7_NONSEC) += exception_level.o
endif
-ifneq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),y)
+ifneq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),y)
obj-y += lowlevel_init.o
endif
diff --git a/arch/arm/cpu/armv8/Makefile b/arch/arm/cpu/armv8/Makefile
index 722ec89d239..c5f568e2cb7 100644
--- a/arch/arm/cpu/armv8/Makefile
+++ b/arch/arm/cpu/armv8/Makefile
@@ -9,7 +9,7 @@ obj-y += cpu.o
ifndef CONFIG_$(SPL_TPL_)TIMER
obj-$(CONFIG_SYS_ARCH_TIMER) += generic_timer.o
endif
-ifndef CONFIG_$(SPL_)SYS_DCACHE_OFF
+ifndef CONFIG_$(XPL_)SYS_DCACHE_OFF
obj-y += cache_v8.o
obj-y += cache.o
endif
@@ -32,7 +32,7 @@ obj-$(CONFIG_ARMV8_SPIN_TABLE) += spin_table.o spin_table_v8.o
else
obj-$(CONFIG_ARCH_SUNXI) += fel_utils.o
endif
-obj-$(CONFIG_$(SPL_)ARMV8_SEC_FIRMWARE_SUPPORT) += sec_firmware.o sec_firmware_asm.o
+obj-$(CONFIG_$(XPL_)ARMV8_SEC_FIRMWARE_SUPPORT) += sec_firmware.o sec_firmware_asm.o
ifdef CONFIG_XPL_BUILD
obj-$(CONFIG_SPL_RECOVER_DATA_SECTION) += spl_data.o
diff --git a/arch/arm/lib/Makefile b/arch/arm/lib/Makefile
index e343e81cf32..b73a0397541 100644
--- a/arch/arm/lib/Makefile
+++ b/arch/arm/lib/Makefile
@@ -94,7 +94,7 @@ endif
# some files can only build in ARM or THUMB2, not THUMB1
-ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
+ifdef CONFIG_$(XPL_)SYS_THUMB_BUILD
asflags-$(CONFIG_HAS_THUMB2) += -DCONFIG_THUMB2_KERNEL
ifndef CONFIG_HAS_THUMB2
diff --git a/arch/arm/mach-at91/arm926ejs/Makefile b/arch/arm/mach-at91/arm926ejs/Makefile
index a8916862b3f..1695708831c 100644
--- a/arch/arm/mach-at91/arm926ejs/Makefile
+++ b/arch/arm/mach-at91/arm926ejs/Makefile
@@ -32,7 +32,7 @@ obj-y += lowlevel_init.o
endif
endif
-ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
+ifdef CONFIG_$(XPL_)SYS_THUMB_BUILD
ifndef CONFIG_HAS_THUMB2
CFLAGS_cache.o := -marm
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index af62a39a671..21d955b4aef 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -60,7 +60,7 @@ obj-$(CONFIG_IMX_RDC) += rdc-sema.o
ifneq ($(CONFIG_XPL_BUILD),y)
obj-$(CONFIG_IMX_BOOTAUX) += imx_bootaux.o
endif
-obj-$(CONFIG_$(SPL_)SATA) += sata.o
+obj-$(CONFIG_$(XPL_)SATA) += sata.o
obj-$(CONFIG_IMX_HAB) += hab.o
obj-$(CONFIG_SYSCOUNTER_TIMER) += syscounter.o
endif
diff --git a/arch/arm/mach-omap2/am33xx/Makefile b/arch/arm/mach-omap2/am33xx/Makefile
index 3f1af7f1633..6f3587f01d0 100644
--- a/arch/arm/mach-omap2/am33xx/Makefile
+++ b/arch/arm/mach-omap2/am33xx/Makefile
@@ -11,7 +11,7 @@ endif
obj-y += sys_info.o
obj-y += ddr.o
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y += emif4.o
endif
obj-y += board.o
diff --git a/arch/arm/mach-orion5x/Makefile b/arch/arm/mach-orion5x/Makefile
index a8b87f6d710..3c381dedaf8 100644
--- a/arch/arm/mach-orion5x/Makefile
+++ b/arch/arm/mach-orion5x/Makefile
@@ -11,13 +11,13 @@ obj-y = cpu.o
obj-y += dram.o
obj-y += timer.o
-ifndef CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT
+ifndef CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT
obj-y += lowlevel_init.o
endif
# some files can only build in ARM or THUMB2, not THUMB1
-ifdef CONFIG_$(SPL_)SYS_THUMB_BUILD
+ifdef CONFIG_$(XPL_)SYS_THUMB_BUILD
ifndef CONFIG_HAS_THUMB2
CFLAGS_cpu.o := -marm
diff --git a/arch/arm/mach-stm32mp/stm32mp1/Makefile b/arch/arm/mach-stm32mp/stm32mp1/Makefile
index 5ae1a536ff1..db160c24cbc 100644
--- a/arch/arm/mach-stm32mp/stm32mp1/Makefile
+++ b/arch/arm/mach-stm32mp/stm32mp1/Makefile
@@ -15,5 +15,5 @@ else
obj-$(CONFIG_ARMV7_PSCI) += psci.o
endif
-obj-$(CONFIG_$(SPL_)STM32MP15_PWR) += pwr_regulator.o
+obj-$(CONFIG_$(XPL_)STM32MP15_PWR) += pwr_regulator.o
obj-$(CONFIG_OF_SYSTEM_SETUP) += fdt.o
diff --git a/arch/arm/mach-tegra/Makefile b/arch/arm/mach-tegra/Makefile
index a87e6a6c352..ebac3473a1f 100644
--- a/arch/arm/mach-tegra/Makefile
+++ b/arch/arm/mach-tegra/Makefile
@@ -16,7 +16,7 @@ obj-$(CONFIG_TEGRA_GP_PADCTRL) += ap.o
obj-y += board.o board2.o
obj-y += cache.o
obj-$(CONFIG_TEGRA_CLKRST) += clock.o
-obj-$(CONFIG_$(SPL_)TEGRA_CRYPTO) += crypto.o
+obj-$(CONFIG_$(XPL_)TEGRA_CRYPTO) += crypto.o
obj-$(CONFIG_TEGRA_PMC) += powergate.o
obj-y += xusb-padctl-dummy.o
diff --git a/arch/arm/mach-tegra/tegra20/Makefile b/arch/arm/mach-tegra/tegra20/Makefile
index 2774c866b02..32c1866b099 100644
--- a/arch/arm/mach-tegra/tegra20/Makefile
+++ b/arch/arm/mach-tegra/tegra20/Makefile
@@ -3,7 +3,7 @@
# (C) Copyright 2010,2011 Nvidia Corporation.
obj-$(CONFIG_XPL_BUILD) += cpu.o
-obj-$(CONFIG_$(SPL_)CMD_EBTUPDATE) += bct.o
+obj-$(CONFIG_$(XPL_)CMD_EBTUPDATE) += bct.o
# The AVP is ARMv4T architecture so we must use special compiler
# flags for any startup files it might use.
diff --git a/arch/arm/mach-tegra/tegra30/Makefile b/arch/arm/mach-tegra/tegra30/Makefile
index 5edc7c9ce7d..b36657a432f 100644
--- a/arch/arm/mach-tegra/tegra30/Makefile
+++ b/arch/arm/mach-tegra/tegra30/Makefile
@@ -3,6 +3,6 @@
# Copyright (c) 2010-2012, NVIDIA CORPORATION. All rights reserved.
obj-$(CONFIG_XPL_BUILD) += cpu.o
-obj-$(CONFIG_$(SPL_)CMD_EBTUPDATE) += bct.o
+obj-$(CONFIG_$(XPL_)CMD_EBTUPDATE) += bct.o
obj-y += clock.o
diff --git a/arch/arm/mach-zynqmp/Makefile b/arch/arm/mach-zynqmp/Makefile
index 7c95f32a5c3..ff426044797 100644
--- a/arch/arm/mach-zynqmp/Makefile
+++ b/arch/arm/mach-zynqmp/Makefile
@@ -7,7 +7,7 @@ obj-y += aes.o clk.o cpu.o
obj-$(CONFIG_MP) += mp.o
obj-$(CONFIG_XPL_BUILD) += spl.o handoff.o psu_spl_init.o
obj-$(CONFIG_SPL_ZYNQMP_DRAM_ECC_INIT) += ecc_spl_init.o
-obj-$(CONFIG_$(SPL_)ZYNQMP_PSU_INIT_ENABLED) += psu_spl_init.o
+obj-$(CONFIG_$(XPL_)ZYNQMP_PSU_INIT_ENABLED) += psu_spl_init.o
ifndef CONFIG_XPL_BUILD
obj-$(CONFIG_CMD_ZYNQMP) += zynqmp.o
diff --git a/arch/riscv/Makefile b/arch/riscv/Makefile
index c36a8533e0f..4e6f347038d 100644
--- a/arch/riscv/Makefile
+++ b/arch/riscv/Makefile
@@ -48,7 +48,7 @@ endif
ARCH_FLAGS = -march=$(RISCV_MARCH) -mabi=$(ABI) \
-mcmodel=$(CMODEL)
-ifeq ($(CONFIG_$(SPL_)FRAMEPOINTER),y)
+ifeq ($(CONFIG_$(XPL_)FRAMEPOINTER),y)
ARCH_FLAGS += -fno-omit-frame-pointer
endif
diff --git a/arch/riscv/lib/Makefile b/arch/riscv/lib/Makefile
index 3bc34cd61fb..34b69c13392 100644
--- a/arch/riscv/lib/Makefile
+++ b/arch/riscv/lib/Makefile
@@ -11,19 +11,19 @@ obj-$(CONFIG_CMD_BOOTI) += bootm.o image.o
obj-$(CONFIG_CMD_GO) += boot.o
obj-y += cache.o
obj-$(CONFIG_SIFIVE_CACHE) += sifive_cache.o
-ifeq ($(CONFIG_$(SPL_)RISCV_MMODE),y)
-obj-$(CONFIG_$(SPL_)RISCV_ACLINT) += aclint_ipi.o
+ifeq ($(CONFIG_$(XPL_)RISCV_MMODE),y)
+obj-$(CONFIG_$(XPL_)RISCV_ACLINT) += aclint_ipi.o
obj-$(CONFIG_ANDES_PLICSW) += andes_plicsw.o
else
obj-$(CONFIG_SBI) += sbi.o
obj-$(CONFIG_SBI_IPI) += sbi_ipi.o
endif
obj-y += interrupts.o
-ifeq ($(CONFIG_$(SPL_)SYSRESET),)
+ifeq ($(CONFIG_$(XPL_)SYSRESET),)
obj-y += reset.o
endif
obj-y += setjmp.o
-obj-$(CONFIG_$(SPL_)SMP) += smp.o
+obj-$(CONFIG_$(XPL_)SMP) += smp.o
obj-$(CONFIG_XPL_BUILD) += spl.o
obj-y += fdt_fixup.o
obj-$(CONFIG_$(SPL)CMD_BDI) += bdinfo.o
diff --git a/arch/x86/Makefile b/arch/x86/Makefile
index 3c8c541efbc..bc1e1ede12a 100644
--- a/arch/x86/Makefile
+++ b/arch/x86/Makefile
@@ -1,7 +1,7 @@
# SPDX-License-Identifier: GPL-2.0+
ifeq ($(CONFIG_EFI_APP),)
-ifdef CONFIG_$(SPL_)X86_64
+ifdef CONFIG_$(XPL_)X86_64
head-y := arch/x86/cpu/start64.o
else
ifeq ($(CONFIG_$(SPL_TPL_)X86_16BIT_INIT),y)
diff --git a/arch/x86/cpu/Makefile b/arch/x86/cpu/Makefile
index c21d6d6d438..8899830370c 100644
--- a/arch/x86/cpu/Makefile
+++ b/arch/x86/cpu/Makefile
@@ -6,7 +6,7 @@
# (C) Copyright 2002
# Daniel Engström, Omicron Ceti AB, daniel at omicron.se.
-ifeq ($(CONFIG_$(SPL_)X86_64),y)
+ifeq ($(CONFIG_$(XPL_)X86_64),y)
extra-y = start64.o
else
ifeq ($(CONFIG_$(SPL_TPL_)X86_16BIT_INIT),y)
@@ -31,7 +31,7 @@ ifndef CONFIG_TPL_BUILD
obj-y += cpu_x86.o
endif
-ifndef CONFIG_$(SPL_)X86_64
+ifndef CONFIG_$(XPL_)X86_64
AFLAGS_REMOVE_call32.o := -mregparm=3 \
$(if $(CONFIG_EFI_STUB_64BIT),-march=i386 -m32)
AFLAGS_call32.o := -fpic -fshort-wchar \
@@ -59,18 +59,18 @@ obj-$(CONFIG_QFW) += qfw_cpu.o
ifndef CONFIG_SYS_COREBOOT
obj-$(CONFIG_$(SPL_TPL_)X86_32BIT_INIT) += irq.o
endif
-ifndef CONFIG_$(SPL_)X86_64
-obj-$(CONFIG_$(SPL_)SMP) += mp_init.o
+ifndef CONFIG_$(XPL_)X86_64
+obj-$(CONFIG_$(XPL_)SMP) += mp_init.o
endif
obj-y += mtrr.o
obj-$(CONFIG_PCI) += pci.o
-ifndef CONFIG_$(SPL_)X86_64
+ifndef CONFIG_$(XPL_)X86_64
obj-$(CONFIG_SMP) += sipi_vector.o
endif
obj-y += turbo.o
obj-$(CONFIG_HAVE_ACPI_RESUME) += wakeup.o
-ifeq ($(CONFIG_$(SPL_)X86_64),y)
+ifeq ($(CONFIG_$(XPL_)X86_64),y)
obj-y += x86_64/
else
obj-y += i386/
diff --git a/arch/x86/cpu/intel_common/Makefile b/arch/x86/cpu/intel_common/Makefile
index 2e312a30353..d2db5897377 100644
--- a/arch/x86/cpu/intel_common/Makefile
+++ b/arch/x86/cpu/intel_common/Makefile
@@ -26,10 +26,10 @@ obj-y += cpu.o
obj-y += fast_spi.o
obj-y += lpc.o
obj-y += lpss.o
-obj-$(CONFIG_$(SPL_)INTEL_GENERIC_WIFI) += generic_wifi.o
+obj-$(CONFIG_$(XPL_)INTEL_GENERIC_WIFI) += generic_wifi.o
ifndef CONFIG_EFI_APP
obj-$(CONFIG_$(SPL_TPL_)X86_32BIT_INIT) += microcode.o
-ifndef CONFIG_$(SPL_)X86_64
+ifndef CONFIG_$(XPL_)X86_64
obj-y += microcode.o
endif
endif
diff --git a/arch/x86/cpu/ivybridge/Makefile b/arch/x86/cpu/ivybridge/Makefile
index 1f3b0c092f1..471ad8d7ebc 100644
--- a/arch/x86/cpu/ivybridge/Makefile
+++ b/arch/x86/cpu/ivybridge/Makefile
@@ -5,15 +5,15 @@
ifdef CONFIG_HAVE_FSP
obj-y += fsp_configs.o ivybridge.o
else
-obj-$(CONFIG_$(SPL_)X86_32BIT_INIT) += cpu.o
+obj-$(CONFIG_$(XPL_)X86_32BIT_INIT) += cpu.o
obj-y += early_me.o
obj-y += lpc.o
obj-y += northbridge.o
ifndef CONFIG_XPL_BUILD
obj-y += sata.o
endif
-obj-$(CONFIG_$(SPL_)X86_32BIT_INIT) += sdram.o
-ifndef CONFIG_$(SPL_)X86_32BIT_INIT
+obj-$(CONFIG_$(XPL_)X86_32BIT_INIT) += sdram.o
+ifndef CONFIG_$(XPL_)X86_32BIT_INIT
obj-y += sdram_nop.o
endif
endif
diff --git a/arch/x86/cpu/qemu/Makefile b/arch/x86/cpu/qemu/Makefile
index b7dd5bd46c7..1439916ac2d 100644
--- a/arch/x86/cpu/qemu/Makefile
+++ b/arch/x86/cpu/qemu/Makefile
@@ -2,7 +2,7 @@
#
# Copyright (C) 2015, Bin Meng <bmeng.cn at gmail.com>
-ifndef CONFIG_$(SPL_)X86_64
+ifndef CONFIG_$(XPL_)X86_64
obj-y += car.o
endif
obj-y += dram.o
diff --git a/arch/x86/lib/Makefile b/arch/x86/lib/Makefile
index 2738f0b577b..53a94901bb4 100644
--- a/arch/x86/lib/Makefile
+++ b/arch/x86/lib/Makefile
@@ -19,7 +19,7 @@ ifndef CONFIG_XPL_BUILD
obj-$(CONFIG_CMD_BOOTM) += bootm.o
endif
obj-y += cmd_boot.o
-obj-$(CONFIG_$(SPL_)COREBOOT_SYSINFO) += coreboot/
+obj-$(CONFIG_$(XPL_)COREBOOT_SYSINFO) += coreboot/
obj-$(CONFIG_SEABIOS) += coreboot_table.o
obj-y += early_cmos.o
obj-y += e820.o
@@ -90,7 +90,7 @@ endif
ifdef CONFIG_EFI_STUB
-ifeq ($(CONFIG_$(SPL_)X86_64),)
+ifeq ($(CONFIG_$(XPL_)X86_64),)
extra-y += $(EFI_CRT0) $(EFI_RELOC)
endif
diff --git a/board/bosch/guardian/Makefile b/board/bosch/guardian/Makefile
index 20cecbfb64e..8e38881ec2c 100644
--- a/board/bosch/guardian/Makefile
+++ b/board/bosch/guardian/Makefile
@@ -5,7 +5,7 @@
# Copyright (C) 2018 Robert Bosch Power Tools GmbH
#
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y := mux.o
endif
diff --git a/board/freescale/common/Makefile b/board/freescale/common/Makefile
index c491dc8b241..c2c86c0dd08 100644
--- a/board/freescale/common/Makefile
+++ b/board/freescale/common/Makefile
@@ -34,7 +34,7 @@ obj-$(CONFIG_FSL_NGPIXIS) += ngpixis.o
endif
obj-$(I2C_COMMON) += i2c_common.o
obj-$(CONFIG_FSL_USE_PCA9547_MUX) += i2c_mux.o
-obj-$(CONFIG_$(SPL_)VID) += vid.o
+obj-$(CONFIG_$(XPL_)VID) += vid.o
obj-$(CONFIG_FSL_QIXIS) += qixis.o
ifndef CONFIG_XPL_BUILD
obj-$(CONFIG_ID_EEPROM) += sys_eeprom.o
@@ -54,7 +54,7 @@ obj-$(CONFIG_TARGET_MPC8548CDS) += cds_pci_ft.o
obj-$(CONFIG_TARGET_P3041DS) += ics307_clk.o
obj-$(CONFIG_TARGET_P4080DS) += ics307_clk.o
obj-$(CONFIG_TARGET_P5040DS) += ics307_clk.o
-ifeq ($(CONFIG_$(SPL_)POWER_LEGACY),y)
+ifeq ($(CONFIG_$(XPL_)POWER_LEGACY),y)
obj-$(CONFIG_POWER_PFUZE100) += pfuze.o
endif
obj-$(CONFIG_DM_PMIC_PFUZE100) += pfuze.o
diff --git a/board/st/common/Makefile b/board/st/common/Makefile
index b01245e4b48..fda48d2ff99 100644
--- a/board/st/common/Makefile
+++ b/board/st/common/Makefile
@@ -8,7 +8,7 @@ obj-$(CONFIG_PMIC_STPMIC1) += stpmic1.o
ifeq ($(CONFIG_ARCH_STM32MP),y)
obj-$(CONFIG_SET_DFU_ALT_INFO) += stm32mp_dfu.o
-obj-$(CONFIG_$(SPL_)DFU_VIRT) += stm32mp_dfu_virt.o
+obj-$(CONFIG_$(XPL_)DFU_VIRT) += stm32mp_dfu_virt.o
endif
obj-$(CONFIG_TYPEC_STUSB160X) += stusb160x.o
diff --git a/board/tcl/sl50/Makefile b/board/tcl/sl50/Makefile
index 0ac0ba36cdb..1502990174b 100644
--- a/board/tcl/sl50/Makefile
+++ b/board/tcl/sl50/Makefile
@@ -4,7 +4,7 @@
#
# Copyright (C) 2015 Toby Churchill Ltd - http://www.toby-churchill.com/
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y := mux.o
endif
diff --git a/board/ti/am335x/Makefile b/board/ti/am335x/Makefile
index 2b1e21a1788..6ef87c22eaa 100644
--- a/board/ti/am335x/Makefile
+++ b/board/ti/am335x/Makefile
@@ -4,7 +4,7 @@
#
# Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y := mux.o
endif
diff --git a/board/ti/am43xx/Makefile b/board/ti/am43xx/Makefile
index b618f632eff..5b7b5b371a4 100644
--- a/board/ti/am43xx/Makefile
+++ b/board/ti/am43xx/Makefile
@@ -4,7 +4,7 @@
#
# Copyright (C) 2013 Texas Instruments Incorporated - https://www.ti.com/
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y := mux.o
endif
diff --git a/board/vscom/baltos/Makefile b/board/vscom/baltos/Makefile
index 2b1e21a1788..6ef87c22eaa 100644
--- a/board/vscom/baltos/Makefile
+++ b/board/vscom/baltos/Makefile
@@ -4,7 +4,7 @@
#
# Copyright (C) 2011 Texas Instruments Incorporated - https://www.ti.com/
-ifeq ($(CONFIG_$(SPL_)SKIP_LOWLEVEL_INIT),)
+ifeq ($(CONFIG_$(XPL_)SKIP_LOWLEVEL_INIT),)
obj-y := mux.o
endif
diff --git a/board/xilinx/zynqmp/Makefile b/board/xilinx/zynqmp/Makefile
index 544346d686e..6476f20eb83 100644
--- a/board/xilinx/zynqmp/Makefile
+++ b/board/xilinx/zynqmp/Makefile
@@ -31,7 +31,7 @@ $(warning Put custom psu_init_gpl.c/h to board/xilinx/zynqmp/custom_hw_platform/
endif
endif
-obj-$(CONFIG_$(SPL_)ZYNQMP_PSU_INIT_ENABLED) += $(init-objs)
+obj-$(CONFIG_$(XPL_)ZYNQMP_PSU_INIT_ENABLED) += $(init-objs)
ifdef CONFIG_XPL_BUILD
ifneq ($(CONFIG_ZYNQMP_SPL_PM_CFG_OBJ_FILE),"")
diff --git a/boot/Makefile b/boot/Makefile
index 5bf07e83388..1b6901970e3 100644
--- a/boot/Makefile
+++ b/boot/Makefile
@@ -50,7 +50,7 @@ obj-$(CONFIG_$(SPL_TPL_)UPL_WRITE) += upl_write.o
obj-$(CONFIG_$(SPL_TPL_)OF_LIBFDT) += image-fdt.o
obj-$(CONFIG_$(SPL_TPL_)FIT_SIGNATURE) += fdt_region.o
obj-$(CONFIG_$(SPL_TPL_)FIT) += image-fit.o
-obj-$(CONFIG_$(SPL_)MULTI_DTB_FIT) += boot_fit.o common_fit.o
+obj-$(CONFIG_$(XPL_)MULTI_DTB_FIT) += boot_fit.o common_fit.o
obj-$(CONFIG_$(SPL_TPL_)IMAGE_PRE_LOAD) += image-pre-load.o
obj-$(CONFIG_$(SPL_TPL_)IMAGE_SIGN_INFO) += image-sig.o
obj-$(CONFIG_$(SPL_TPL_)FIT_SIGNATURE) += image-fit-sig.o
diff --git a/cmd/Makefile b/cmd/Makefile
index ed62e1c45f8..21d376309b9 100644
--- a/cmd/Makefile
+++ b/cmd/Makefile
@@ -249,7 +249,7 @@ obj-$(CONFIG_ARCH_K3) += ti/
obj-$(CONFIG_ARCH_OMAP2PLUS) += ti/
endif # !CONFIG_XPL_BUILD
-obj-$(CONFIG_$(SPL_)CMD_TLV_EEPROM) += tlv_eeprom.o
+obj-$(CONFIG_$(XPL_)CMD_TLV_EEPROM) += tlv_eeprom.o
obj-$(CONFIG_CMD_BCM_EXT_UTILS) += broadcom/
diff --git a/doc/develop/tests_writing.rst b/doc/develop/tests_writing.rst
index a328ebfef33..54efb7e1b04 100644
--- a/doc/develop/tests_writing.rst
+++ b/doc/develop/tests_writing.rst
@@ -321,15 +321,15 @@ to control that.
Finally, add the test to the build by adding to the Makefile in the same
directory::
- obj-$(CONFIG_$(SPL_)CMDLINE) += wibble.o
+ obj-$(CONFIG_$(XPL_)CMDLINE) += wibble.o
Note that CMDLINE is never enabled in SPL, so this test will only be present in
U-Boot proper. See below for how to do SPL tests.
As before, you can add an extra Kconfig check if needed::
- ifneq ($(CONFIG_$(SPL_)WIBBLE),)
- obj-$(CONFIG_$(SPL_)CMDLINE) += wibble.o
+ ifneq ($(CONFIG_$(XPL_)WIBBLE),)
+ obj-$(CONFIG_$(XPL_)CMDLINE) += wibble.o
endif
diff --git a/drivers/Makefile b/drivers/Makefile
index 1b7db812828..b44570fdb65 100644
--- a/drivers/Makefile
+++ b/drivers/Makefile
@@ -33,15 +33,15 @@ obj-$(CONFIG_$(SPL_TPL_)SERIAL) += serial/
obj-$(CONFIG_$(SPL_TPL_)SPI) += spi/
obj-$(CONFIG_$(SPL_TPL_)TIMER) += timer/
obj-$(CONFIG_$(SPL_TPL_)VIRTIO) += virtio/
-obj-$(CONFIG_$(SPL_)DM_MAILBOX) += mailbox/
-obj-$(CONFIG_$(SPL_)REMOTEPROC) += remoteproc/
-obj-$(CONFIG_$(SPL_)SYSINFO) += sysinfo/
+obj-$(CONFIG_$(XPL_)DM_MAILBOX) += mailbox/
+obj-$(CONFIG_$(XPL_)REMOTEPROC) += remoteproc/
+obj-$(CONFIG_$(XPL_)SYSINFO) += sysinfo/
obj-$(CONFIG_$(SPL_TPL_)SM) += sm/
obj-$(CONFIG_$(SPL_TPL_)TPM) += tpm/
-obj-$(CONFIG_$(SPL_)NVME) += nvme/
+obj-$(CONFIG_$(XPL_)NVME) += nvme/
obj-$(CONFIG_XEN) += xen/
-obj-$(CONFIG_$(SPL_)FPGA) += fpga/
-obj-$(CONFIG_$(SPL_)VIDEO) += video/
+obj-$(CONFIG_$(XPL_)FPGA) += fpga/
+obj-$(CONFIG_$(XPL_)VIDEO) += video/
obj-y += bus/
@@ -54,7 +54,7 @@ obj-$(CONFIG_SPL_CRYPTO) += crypto/
obj-$(CONFIG_SPL_MPC8XXX_INIT_DDR) += ddr/fsl/
obj-$(CONFIG_ARMADA_38X) += ddr/marvell/a38x/
obj-$(CONFIG_ARMADA_XP) += ddr/marvell/axp/
-obj-$(CONFIG_$(SPL_)ALTERA_SDRAM) += ddr/altera/
+obj-$(CONFIG_$(XPL_)ALTERA_SDRAM) += ddr/altera/
obj-$(CONFIG_ARCH_IMX8M) += ddr/imx/imx8m/
obj-$(CONFIG_IMX8ULP_DRAM) += ddr/imx/imx8ulp/
obj-$(CONFIG_ARCH_IMX9) += ddr/imx/imx9/
diff --git a/drivers/ata/Makefile b/drivers/ata/Makefile
index af6f0bf2780..ee10c4445b0 100644
--- a/drivers/ata/Makefile
+++ b/drivers/ata/Makefile
@@ -5,7 +5,7 @@
obj-$(CONFIG_DWC_AHCI) += dwc_ahci.o
obj-$(CONFIG_AHCI) += ahci-uclass.o
-obj-$(CONFIG_$(SPL_)AHCI_PCI) += ahci-pci.o
+obj-$(CONFIG_$(XPL_)AHCI_PCI) += ahci-pci.o
obj-$(CONFIG_SCSI_AHCI) += ahci.o
obj-$(CONFIG_DWC_AHSATA) += dwc_ahsata.o
obj-$(CONFIG_FSL_SATA) += fsl_sata.o
diff --git a/drivers/block/Makefile b/drivers/block/Makefile
index a551591fc91..98a34c01c38 100644
--- a/drivers/block/Makefile
+++ b/drivers/block/Makefile
@@ -5,7 +5,7 @@
obj-$(CONFIG_$(SPL_TPL_)BLK) += blk-uclass.o
-ifndef CONFIG_$(SPL_)BLK
+ifndef CONFIG_$(XPL_)BLK
obj-$(CONFIG_SPL_LEGACY_BLOCK) += blk_legacy.o
endif
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index e14cb7fd9c7..7daf8247247 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -8,4 +8,4 @@ obj-$(CONFIG_TI_PWMSS) += ti-pwmss.o
obj-$(CONFIG_UNIPHIER_SYSTEM_BUS) += uniphier-system-bus.o
endif
-obj-$(CONFIG_$(SPL_)TI_SYSC) += ti-sysc.o
+obj-$(CONFIG_$(XPL_)TI_SYSC) += ti-sysc.o
diff --git a/drivers/core/Makefile b/drivers/core/Makefile
index acbd2bf2cef..20dbff6f956 100644
--- a/drivers/core/Makefile
+++ b/drivers/core/Makefile
@@ -6,16 +6,16 @@ obj-y += device.o fdtaddr.o lists.o root.o uclass.o util.o tag.o
obj-$(CONFIG_$(SPL_TPL_)ACPIGEN) += acpi.o
obj-$(CONFIG_$(SPL_TPL_)DEVRES) += devres.o
obj-$(CONFIG_$(SPL_TPL_)DM_DEVICE_REMOVE) += device-remove.o
-obj-$(CONFIG_$(SPL_)SIMPLE_BUS) += simple-bus.o
+obj-$(CONFIG_$(XPL_)SIMPLE_BUS) += simple-bus.o
obj-$(CONFIG_SIMPLE_PM_BUS) += simple-pm-bus.o
obj-$(CONFIG_DM) += dump.o
obj-$(CONFIG_$(SPL_TPL_)REGMAP) += regmap.o
obj-$(CONFIG_$(SPL_TPL_)SYSCON) += syscon-uclass.o
-obj-$(CONFIG_$(SPL_)OF_LIVE) += of_access.o of_addr.o
+obj-$(CONFIG_$(XPL_)OF_LIVE) += of_access.o of_addr.o
ifndef CONFIG_DM_DEV_READ_INLINE
obj-$(CONFIG_OF_CONTROL) += read.o
endif
-obj-$(CONFIG_$(SPL_)OF_PLATDATA) += read.o
+obj-$(CONFIG_$(XPL_)OF_PLATDATA) += read.o
obj-$(CONFIG_OF_CONTROL) += of_extra.o ofnode.o read_extra.o
ccflags-$(CONFIG_DM_DEBUG) += -DDEBUG
diff --git a/drivers/ddr/altera/Makefile b/drivers/ddr/altera/Makefile
index 9fa5d85a27e..c1d6a6b6c59 100644
--- a/drivers/ddr/altera/Makefile
+++ b/drivers/ddr/altera/Makefile
@@ -6,7 +6,7 @@
# (C) Copyright 2010, Thomas Chou <thomas at wytron.com.tw>
# Copyright (C) 2014-2021 Altera Corporation <www.altera.com>
-ifdef CONFIG_$(SPL_)ALTERA_SDRAM
+ifdef CONFIG_$(XPL_)ALTERA_SDRAM
obj-$(CONFIG_TARGET_SOCFPGA_GEN5) += sdram_gen5.o sequencer.o
obj-$(CONFIG_TARGET_SOCFPGA_ARRIA10) += sdram_arria10.o
obj-$(CONFIG_TARGET_SOCFPGA_STRATIX10) += sdram_soc64.o sdram_s10.o
diff --git a/drivers/dfu/Makefile b/drivers/dfu/Makefile
index dfbf64da667..05d7cc61caa 100644
--- a/drivers/dfu/Makefile
+++ b/drivers/dfu/Makefile
@@ -3,11 +3,11 @@
# Copyright (C) 2012 Samsung Electronics
# Lukasz Majewski <l.majewski at samsung.com>
-obj-$(CONFIG_$(SPL_)DFU) += dfu.o
-obj-$(CONFIG_$(SPL_)DFU_MMC) += dfu_mmc.o
-obj-$(CONFIG_$(SPL_)DFU_MTD) += dfu_mtd.o
-obj-$(CONFIG_$(SPL_)DFU_NAND) += dfu_nand.o
-obj-$(CONFIG_$(SPL_)DFU_RAM) += dfu_ram.o
-obj-$(CONFIG_$(SPL_)DFU_SF) += dfu_sf.o
-obj-$(CONFIG_$(SPL_)DFU_WRITE_ALT) += dfu_alt.o
-obj-$(CONFIG_$(SPL_)DFU_VIRT) += dfu_virt.o
+obj-$(CONFIG_$(XPL_)DFU) += dfu.o
+obj-$(CONFIG_$(XPL_)DFU_MMC) += dfu_mmc.o
+obj-$(CONFIG_$(XPL_)DFU_MTD) += dfu_mtd.o
+obj-$(CONFIG_$(XPL_)DFU_NAND) += dfu_nand.o
+obj-$(CONFIG_$(XPL_)DFU_RAM) += dfu_ram.o
+obj-$(CONFIG_$(XPL_)DFU_SF) += dfu_sf.o
+obj-$(CONFIG_$(XPL_)DFU_WRITE_ALT) += dfu_alt.o
+obj-$(CONFIG_$(XPL_)DFU_VIRT) += dfu_virt.o
diff --git a/drivers/firmware/Makefile b/drivers/firmware/Makefile
index 7ce83d72bd3..8b979f69ed9 100644
--- a/drivers/firmware/Makefile
+++ b/drivers/firmware/Makefile
@@ -1,5 +1,5 @@
obj-$(CONFIG_FIRMWARE) += firmware-uclass.o
-obj-$(CONFIG_$(SPL_)ARM_PSCI_FW) += psci.o
+obj-$(CONFIG_$(XPL_)ARM_PSCI_FW) += psci.o
obj-$(CONFIG_TI_SCI_PROTOCOL) += ti_sci.o
obj-$(CONFIG_SANDBOX) += firmware-sandbox.o
obj-$(CONFIG_ZYNQMP_FIRMWARE) += firmware-zynqmp.o
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 990a670dd7b..24d1b0394fb 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -10,7 +10,7 @@ obj-$(CONFIG_DM_74X164) += 74x164_gpio.o
endif
obj-$(CONFIG_$(SPL_TPL_)DM_GPIO) += gpio-uclass.o
-obj-$(CONFIG_$(SPL_)DM_PCA953X) += pca953x_gpio.o
+obj-$(CONFIG_$(XPL_)DM_PCA953X) += pca953x_gpio.o
obj-$(CONFIG_ASPEED_GPIO) += gpio-aspeed.o
obj-$(CONFIG_ASPEED_G7_GPIO) += gpio-aspeed-g7.o
@@ -57,12 +57,12 @@ obj-$(CONFIG_VYBRID_GPIO) += vybrid_gpio.o
obj-$(CONFIG_HIKEY_GPIO) += hi6220_gpio.o
obj-$(CONFIG_HSDK_CREG_GPIO) += hsdk-creg-gpio.o
obj-$(CONFIG_IMX_RGPIO2P) += imx_rgpio2p.o
-obj-$(CONFIG_$(SPL_)PALMAS_GPIO) += palmas_gpio.o
+obj-$(CONFIG_$(XPL_)PALMAS_GPIO) += palmas_gpio.o
obj-$(CONFIG_PIC32_GPIO) += pic32_gpio.o
obj-$(CONFIG_OCTEON_GPIO) += octeon_gpio.o
obj-$(CONFIG_MVEBU_GPIO) += mvebu_gpio.o
obj-$(CONFIG_MSM_GPIO) += msm_gpio.o
-obj-$(CONFIG_$(SPL_)PCF8575_GPIO) += pcf8575_gpio.o
+obj-$(CONFIG_$(XPL_)PCF8575_GPIO) += pcf8575_gpio.o
obj-$(CONFIG_$(SPL_TPL_)QCOM_PMIC_GPIO) += qcom_pmic_gpio.o
obj-$(CONFIG_MT7620_GPIO) += mt7620_gpio.o
obj-$(CONFIG_MT7621_GPIO) += mt7621_gpio.o
@@ -71,7 +71,7 @@ obj-$(CONFIG_NX_GPIO) += nx_gpio.o
obj-$(CONFIG_SIFIVE_GPIO) += sifive-gpio.o
obj-$(CONFIG_NOMADIK_GPIO) += nmk_gpio.o
obj-$(CONFIG_MAX7320_GPIO) += max7320_gpio.o
-obj-$(CONFIG_$(SPL_)MAX77663_GPIO) += max77663_gpio.o
+obj-$(CONFIG_$(XPL_)MAX77663_GPIO) += max77663_gpio.o
obj-$(CONFIG_SL28CPLD_GPIO) += sl28cpld-gpio.o
obj-$(CONFIG_ZYNQMP_GPIO_MODEPIN) += zynqmp_gpio_modepin.o
obj-$(CONFIG_SLG7XL45106_I2C_GPO) += gpio_slg7xl45106.o
diff --git a/drivers/i2c/Makefile b/drivers/i2c/Makefile
index 00b90523c62..bebd728e7da 100644
--- a/drivers/i2c/Makefile
+++ b/drivers/i2c/Makefile
@@ -2,15 +2,15 @@
#
# (C) Copyright 2000-2007
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-obj-$(CONFIG_$(SPL_)DM_I2C) += i2c-uclass.o
-ifdef CONFIG_$(SPL_)ACPIGEN
-obj-$(CONFIG_$(SPL_)DM_I2C) += acpi_i2c.o
+obj-$(CONFIG_$(XPL_)DM_I2C) += i2c-uclass.o
+ifdef CONFIG_$(XPL_)ACPIGEN
+obj-$(CONFIG_$(XPL_)DM_I2C) += acpi_i2c.o
endif
-obj-$(CONFIG_$(SPL_)DM_I2C_GPIO) += i2c-gpio.o
-obj-$(CONFIG_$(SPL_)I2C_CROS_EC_TUNNEL) += cros_ec_tunnel.o
-obj-$(CONFIG_$(SPL_)I2C_CROS_EC_LDO) += cros_ec_ldo.o
+obj-$(CONFIG_$(XPL_)DM_I2C_GPIO) += i2c-gpio.o
+obj-$(CONFIG_$(XPL_)I2C_CROS_EC_TUNNEL) += cros_ec_tunnel.o
+obj-$(CONFIG_$(XPL_)I2C_CROS_EC_LDO) += cros_ec_ldo.o
-obj-$(CONFIG_$(SPL_)SYS_I2C_LEGACY) += i2c_core.o
+obj-$(CONFIG_$(XPL_)SYS_I2C_LEGACY) += i2c_core.o
obj-$(CONFIG_SYS_I2C_ASPEED) += ast_i2c.o
obj-$(CONFIG_SYS_I2C_AST2600) += ast2600_i2c.o
obj-$(CONFIG_SYS_I2C_AT91) += at91_i2c.o
@@ -57,4 +57,4 @@ obj-$(CONFIG_SYS_I2C_VERSATILE) += i2c-versatile.o
obj-$(CONFIG_SYS_I2C_XILINX_XIIC) += xilinx_xiic.o
obj-$(CONFIG_TEGRA186_BPMP_I2C) += tegra186_bpmp_i2c.o
-obj-$(CONFIG_$(SPL_)I2C_MUX) += muxes/
+obj-$(CONFIG_$(XPL_)I2C_MUX) += muxes/
diff --git a/drivers/led/Makefile b/drivers/led/Makefile
index e27aa488482..aa64a38b4e1 100644
--- a/drivers/led/Makefile
+++ b/drivers/led/Makefile
@@ -10,6 +10,6 @@ obj-$(CONFIG_LED_BCM6358) += led_bcm6358.o
obj-$(CONFIG_LED_BCM6753) += led_bcm6753.o
obj-$(CONFIG_LED_BCM6858) += led_bcm6858.o
obj-$(CONFIG_LED_PWM) += led_pwm.o
-obj-$(CONFIG_$(SPL_)LED_GPIO) += led_gpio.o
+obj-$(CONFIG_$(XPL_)LED_GPIO) += led_gpio.o
obj-$(CONFIG_LED_CORTINA) += led_cortina.o
obj-$(CONFIG_LED_LP5562) += led_lp5562.o
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index 59e8d0de93c..6072fa1956b 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -3,7 +3,7 @@
# Copyright (c) 2016, NVIDIA CORPORATION.
#
-obj-$(CONFIG_$(SPL_)DM_MAILBOX) += mailbox-uclass.o
+obj-$(CONFIG_$(XPL_)DM_MAILBOX) += mailbox-uclass.o
obj-$(CONFIG_APPLE_MBOX) += apple-mbox.o
obj-$(CONFIG_SANDBOX_MBOX) += sandbox-mbox.o
obj-$(CONFIG_SANDBOX_MBOX) += sandbox-mbox-test.o
diff --git a/drivers/misc/Makefile b/drivers/misc/Makefile
index 51ef51f1ed3..794c2a2d38e 100644
--- a/drivers/misc/Makefile
+++ b/drivers/misc/Makefile
@@ -18,7 +18,7 @@ obj-$(CONFIG_SANDBOX) += p2sb_sandbox.o p2sb_emul.o
obj-$(CONFIG_SANDBOX) += swap_case.o
endif
-ifdef CONFIG_$(SPL_)DM_I2C
+ifdef CONFIG_$(XPL_)DM_I2C
ifndef CONFIG_XPL_BUILD
obj-$(CONFIG_SANDBOX) += i2c_eeprom_emul.o
obj-$(CONFIG_USB_HUB_USB251XB) += usb251xb.o
@@ -37,14 +37,14 @@ obj-$(CONFIG_FSL_DEVICE_DISABLE) += fsl_devdis.o
obj-$(CONFIG_FSL_IFC) += fsl_ifc.o
obj-$(CONFIG_FSL_IIM) += fsl_iim.o
obj-$(CONFIG_FSL_SEC_MON) += fsl_sec_mon.o
-obj-$(CONFIG_$(SPL_)FS_LOADER) += fs_loader.o
+obj-$(CONFIG_$(XPL_)FS_LOADER) += fs_loader.o
obj-$(CONFIG_GATEWORKS_SC) += gsc.o
obj-$(CONFIG_GDSYS_IOEP) += gdsys_ioep.o
obj-$(CONFIG_GDSYS_RXAUI_CTRL) += gdsys_rxaui_ctrl.o
obj-$(CONFIG_GDSYS_SOC) += gdsys_soc.o
obj-$(CONFIG_IRQ) += irq-uclass.o
obj-$(CONFIG_SANDBOX) += irq_sandbox.o irq_sandbox_test.o
-obj-$(CONFIG_$(SPL_)I2C_EEPROM) += i2c_eeprom.o
+obj-$(CONFIG_$(XPL_)I2C_EEPROM) += i2c_eeprom.o
obj-$(CONFIG_IHS_FPGA) += ihs_fpga.o
obj-$(CONFIG_IMX8) += imx8/
obj-$(CONFIG_IMX_ELE) += imx_ele/
@@ -52,14 +52,14 @@ obj-$(CONFIG_LED_STATUS) += status_led.o
obj-$(CONFIG_LED_STATUS_GPIO) += gpio_led.o
obj-$(CONFIG_MPC83XX_SERDES) += mpc83xx_serdes.o
obj-$(CONFIG_$(SPL_TPL_)LS2_SFP) += ls2_sfp.o
-obj-$(CONFIG_$(SPL_)MXC_OCOTP) += mxc_ocotp.o
+obj-$(CONFIG_$(XPL_)MXC_OCOTP) += mxc_ocotp.o
obj-$(CONFIG_MXS_OCOTP) += mxs_ocotp.o
obj-$(CONFIG_NPCM_OTP) += npcm_otp.o
obj-$(CONFIG_NPCM_HOST) += npcm_host_intf.o
obj-$(CONFIG_NUVOTON_NCT6102D) += nuvoton_nct6102d.o
obj-$(CONFIG_P2SB) += p2sb-uclass.o
obj-$(CONFIG_PCA9551_LED) += pca9551_led.o
-obj-$(CONFIG_$(SPL_)PWRSEQ) += pwrseq-uclass.o
+obj-$(CONFIG_$(XPL_)PWRSEQ) += pwrseq-uclass.o
ifdef CONFIG_QFW
obj-y += qfw.o
obj-$(CONFIG_QFW_ACPI) += qfw_acpi.o
diff --git a/drivers/mmc/Makefile b/drivers/mmc/Makefile
index 952201923d8..328653b8823 100644
--- a/drivers/mmc/Makefile
+++ b/drivers/mmc/Makefile
@@ -4,17 +4,17 @@
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
obj-y += mmc.o
-obj-$(CONFIG_$(SPL_)DM_MMC) += mmc-uclass.o
+obj-$(CONFIG_$(XPL_)DM_MMC) += mmc-uclass.o
ifdef CONFIG_$(SPL_TPL_)DM_MMC
obj-$(CONFIG_$(SPL_TPL_)BOOTSTD) += mmc_bootdev.o
endif
obj-$(CONFIG_$(SPL_TPL_)MMC_WRITE) += mmc_write.o
-obj-$(CONFIG_$(SPL_)MMC_PWRSEQ) += mmc-pwrseq.o
+obj-$(CONFIG_$(XPL_)MMC_PWRSEQ) += mmc-pwrseq.o
obj-$(CONFIG_MMC_SDHCI_ADMA_HELPERS) += sdhci-adma.o
-ifndef CONFIG_$(SPL_)BLK
+ifndef CONFIG_$(XPL_)BLK
obj-y += mmc_legacy.o
endif
diff --git a/drivers/mux/Makefile b/drivers/mux/Makefile
index d4e24789d33..63770e12bd1 100644
--- a/drivers/mux/Makefile
+++ b/drivers/mux/Makefile
@@ -4,4 +4,4 @@
# Jean-Jacques Hiblot <jjhiblot at ti.com>
obj-$(CONFIG_MULTIPLEXER) += mux-uclass.o
-obj-$(CONFIG_$(SPL_)MUX_MMIO) += mmio.o
+obj-$(CONFIG_$(XPL_)MUX_MMIO) += mmio.o
diff --git a/drivers/nvme/Makefile b/drivers/nvme/Makefile
index fd3e68a91dc..8c32cfbfc0f 100644
--- a/drivers/nvme/Makefile
+++ b/drivers/nvme/Makefile
@@ -4,4 +4,4 @@
obj-y += nvme-uclass.o nvme.o nvme_show.o
obj-$(CONFIG_NVME_APPLE) += nvme_apple.o
-obj-$(CONFIG_$(SPL_)NVME_PCI) += nvme_pci.o
+obj-$(CONFIG_$(XPL_)NVME_PCI) += nvme_pci.o
diff --git a/drivers/phy/Makefile b/drivers/phy/Makefile
index 7a2b764492b..c35f9294dd9 100644
--- a/drivers/phy/Makefile
+++ b/drivers/phy/Makefile
@@ -8,8 +8,8 @@ obj-y += marvell/
obj-y += rockchip/
obj-y += socionext/
-obj-$(CONFIG_$(SPL_)PHY) += phy-uclass.o
-obj-$(CONFIG_$(SPL_)NOP_PHY) += nop-phy.o
+obj-$(CONFIG_$(XPL_)PHY) += phy-uclass.o
+obj-$(CONFIG_$(XPL_)NOP_PHY) += nop-phy.o
obj-$(CONFIG_MIPI_DPHY_HELPERS) += phy-core-mipi-dphy.o
obj-$(CONFIG_AB8500_USB_PHY) += phy-ab8500-usb.o
obj-$(CONFIG_APPLE_ATCPHY) += phy-apple-atc.o
@@ -19,7 +19,7 @@ obj-$(CONFIG_BCM6358_USBH_PHY) += bcm6358-usbh-phy.o
obj-$(CONFIG_BCM6368_USBH_PHY) += bcm6368-usbh-phy.o
obj-$(CONFIG_BCM_SR_PCIE_PHY) += phy-bcm-sr-pcie.o
obj-$(CONFIG_PHY_SANDBOX) += sandbox-phy.o
-obj-$(CONFIG_$(SPL_)PIPE3_PHY) += ti-pipe3-phy.o
+obj-$(CONFIG_$(XPL_)PIPE3_PHY) += ti-pipe3-phy.o
obj-$(CONFIG_AM654_PHY) += phy-ti-am654.o
obj-$(CONFIG_STI_USB_PHY) += sti_usb_phy.o
obj-$(CONFIG_PHY_RCAR_GEN2) += phy-rcar-gen2.o
diff --git a/drivers/phy/cadence/Makefile b/drivers/phy/cadence/Makefile
index af63b32d9f5..e0da41cd7eb 100644
--- a/drivers/phy/cadence/Makefile
+++ b/drivers/phy/cadence/Makefile
@@ -1,2 +1,2 @@
-obj-$(CONFIG_$(SPL_)PHY_CADENCE_SIERRA) += phy-cadence-sierra.o
-obj-$(CONFIG_$(SPL_)PHY_CADENCE_TORRENT) += phy-cadence-torrent.o
+obj-$(CONFIG_$(XPL_)PHY_CADENCE_SIERRA) += phy-cadence-sierra.o
+obj-$(CONFIG_$(XPL_)PHY_CADENCE_TORRENT) += phy-cadence-torrent.o
diff --git a/drivers/phy/ti/Makefile b/drivers/phy/ti/Makefile
index 873ddbf0363..699901fd15e 100644
--- a/drivers/phy/ti/Makefile
+++ b/drivers/phy/ti/Makefile
@@ -1 +1 @@
-obj-$(CONFIG_$(SPL_)PHY_J721E_WIZ) += phy-j721e-wiz.o
+obj-$(CONFIG_$(XPL_)PHY_J721E_WIZ) += phy-j721e-wiz.o
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index 6d7b7cd9051..634047a91f4 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -1,13 +1,13 @@
# SPDX-License-Identifier: GPL-2.0+
obj-y += pinctrl-uclass.o
-obj-$(CONFIG_$(SPL_)PINCTRL_GENERIC) += pinctrl-generic.o
+obj-$(CONFIG_$(XPL_)PINCTRL_GENERIC) += pinctrl-generic.o
obj-$(CONFIG_PINCTRL_APPLE) += pinctrl-apple.o
obj-$(CONFIG_PINCTRL_AT91) += pinctrl-at91.o
obj-$(CONFIG_PINCTRL_AT91PIO4) += pinctrl-at91-pio4.o
obj-y += nxp/
-obj-$(CONFIG_$(SPL_)PINCTRL_ROCKCHIP) += rockchip/
+obj-$(CONFIG_$(XPL_)PINCTRL_ROCKCHIP) += rockchip/
obj-$(CONFIG_ARCH_ASPEED) += aspeed/
obj-$(CONFIG_ARCH_ATH79) += ath79/
obj-$(CONFIG_PINCTRL_INTEL) += intel/
@@ -18,7 +18,7 @@ obj-$(CONFIG_ARCH_RENESAS) += renesas/
obj-$(CONFIG_ARCH_RZN1) += renesas/
obj-$(CONFIG_PINCTRL_SANDBOX) += pinctrl-sandbox.o
obj-$(CONFIG_PINCTRL_SUNXI) += sunxi/
-obj-$(CONFIG_$(SPL_)PINCTRL_TEGRA) += tegra/
+obj-$(CONFIG_$(XPL_)PINCTRL_TEGRA) += tegra/
obj-$(CONFIG_PINCTRL_UNIPHIER) += uniphier/
obj-$(CONFIG_PINCTRL_PIC32) += pinctrl_pic32.o
obj-$(CONFIG_PINCTRL_EXYNOS) += exynos/
@@ -32,7 +32,7 @@ obj-$(CONFIG_PINCTRL_QE) += pinctrl-qe-io.o
obj-$(CONFIG_PINCTRL_SINGLE) += pinctrl-single.o
obj-$(CONFIG_PINCTRL_STI) += pinctrl-sti.o
obj-$(CONFIG_PINCTRL_STM32) += pinctrl_stm32.o
-obj-$(CONFIG_$(SPL_)PINCTRL_STMFX) += pinctrl-stmfx.o
+obj-$(CONFIG_$(XPL_)PINCTRL_STMFX) += pinctrl-stmfx.o
obj-y += broadcom/
obj-$(CONFIG_PINCTRL_ZYNQMP) += pinctrl-zynqmp.o
obj-$(CONFIG_PINCTRL_STARFIVE) += starfive/
diff --git a/drivers/power/domain/Makefile b/drivers/power/domain/Makefile
index 2daab73eb75..110646c503a 100644
--- a/drivers/power/domain/Makefile
+++ b/drivers/power/domain/Makefile
@@ -3,7 +3,7 @@
# Copyright (c) 2016, NVIDIA CORPORATION.
#
-obj-$(CONFIG_$(SPL_)POWER_DOMAIN) += power-domain-uclass.o
+obj-$(CONFIG_$(XPL_)POWER_DOMAIN) += power-domain-uclass.o
obj-$(CONFIG_APPLE_PMGR_POWER_DOMAIN) += apple-pmgr.o
obj-$(CONFIG_BCM6328_POWER_DOMAIN) += bcm6328-power-domain.o
obj-$(CONFIG_IMX8_POWER_DOMAIN) += imx8-power-domain-legacy.o imx8-power-domain.o
diff --git a/drivers/power/pmic/Makefile b/drivers/power/pmic/Makefile
index a2d59deeed8..48f7dd49ef8 100644
--- a/drivers/power/pmic/Makefile
+++ b/drivers/power/pmic/Makefile
@@ -4,33 +4,33 @@
# Lukasz Majewski <l.majewski at samsung.com>
obj-$(CONFIG_$(SPL_TPL_)DM_PMIC) += pmic-uclass.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_FAN53555) += fan53555.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_DA9063) += da9063.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_MAX77663) += max77663.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_FAN53555) += fan53555.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_DA9063) += da9063.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_MAX77663) += max77663.o
obj-$(CONFIG_DM_PMIC_MAX77686) += max77686.o
obj-$(CONFIG_DM_PMIC_MAX8998) += max8998.o
obj-$(CONFIG_DM_PMIC_MC34708) += mc34708.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_BD71837) += bd71837.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_MP5416) += mp5416.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_PFUZE100) += pfuze100.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_PCA9450) += pca9450.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_BD71837) += bd71837.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_MP5416) += mp5416.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_PFUZE100) += pfuze100.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_PCA9450) += pca9450.o
obj-$(CONFIG_PMIC_S2MPS11) += s2mps11.o
obj-$(CONFIG_DM_PMIC_SANDBOX) += sandbox.o i2c_pmic_emul.o
obj-$(CONFIG_PMIC_AB8500) += ab8500.o
obj-$(CONFIG_PMIC_ACT8846) += act8846.o
obj-$(CONFIG_PMIC_AS3722) += as3722.o as3722_gpio.o
-obj-$(CONFIG_$(SPL_)PMIC_AXP) += axp.o
+obj-$(CONFIG_$(XPL_)PMIC_AXP) += axp.o
obj-$(CONFIG_PMIC_MAX8997) += max8997.o
obj-$(CONFIG_PMIC_QCOM) += pmic_qcom.o
obj-$(CONFIG_$(SPL_TPL_)PMIC_RK8XX) += rk8xx.o
-obj-$(CONFIG_$(SPL_)PMIC_RN5T567) += rn5t567.o
+obj-$(CONFIG_$(XPL_)PMIC_RN5T567) += rn5t567.o
obj-$(CONFIG_PMIC_TPS65090) += tps65090.o
obj-$(CONFIG_PMIC_S5M8767) += s5m8767.o
obj-$(CONFIG_DM_PMIC_TPS65910) += pmic_tps65910_dm.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_TPS80031) += tps80031.o
-obj-$(CONFIG_$(SPL_)PMIC_PALMAS) += palmas.o
-obj-$(CONFIG_$(SPL_)PMIC_LP873X) += lp873x.o
-obj-$(CONFIG_$(SPL_)PMIC_LP87565) += lp87565.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_TPS80031) += tps80031.o
+obj-$(CONFIG_$(XPL_)PMIC_PALMAS) += palmas.o
+obj-$(CONFIG_$(XPL_)PMIC_LP873X) += lp873x.o
+obj-$(CONFIG_$(XPL_)PMIC_LP87565) += lp87565.o
obj-$(CONFIG_PMIC_STPMIC1) += stpmic1.o
obj-$(CONFIG_PMIC_TPS65217) += pmic_tps65217.o
obj-$(CONFIG_PMIC_TPS65219) += tps65219.o
@@ -38,7 +38,7 @@ obj-$(CONFIG_PMIC_TPS65941) += tps65941.o
obj-$(CONFIG_PMIC_RAA215300) += raa215300.o
obj-$(CONFIG_POWER_TPS65218) += pmic_tps65218.o
-ifeq ($(CONFIG_$(SPL_)POWER_LEGACY),y)
+ifeq ($(CONFIG_$(XPL_)POWER_LEGACY),y)
obj-$(CONFIG_POWER_LTC3676) += pmic_ltc3676.o
obj-$(CONFIG_POWER_PCA9450) += pmic_pca9450.o
obj-$(CONFIG_POWER_PFUZE100) += pmic_pfuze100.o
@@ -47,5 +47,5 @@ obj-$(CONFIG_POWER_HI6553) += pmic_hi6553.o
obj-$(CONFIG_POWER_MC34VR500) += pmic_mc34vr500.o
endif
-obj-$(CONFIG_$(SPL_)POWER_TPS62362) += pmic_tps62362.o
+obj-$(CONFIG_$(XPL_)POWER_TPS62362) += pmic_tps62362.o
obj-$(CONFIG_SPL_POWER_TPS65910) += pmic_tps65910.o
diff --git a/drivers/power/regulator/Makefile b/drivers/power/regulator/Makefile
index 54db0885657..cac02aaa36f 100644
--- a/drivers/power/regulator/Makefile
+++ b/drivers/power/regulator/Makefile
@@ -4,41 +4,41 @@
# Przemyslaw Marczak <p.marczak at samsung.com>
#
-obj-$(CONFIG_$(SPL_)DM_REGULATOR) += regulator-uclass.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR) += regulator-uclass.o
obj-$(CONFIG_REGULATOR_ACT8846) += act8846.o
obj-$(CONFIG_REGULATOR_AS3722) += as3722_regulator.o
-obj-$(CONFIG_$(SPL_)REGULATOR_AXP) += axp_regulator.o
-obj-$(CONFIG_$(SPL_)REGULATOR_AXP_USB_POWER) += axp_usb_power.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_DA9063) += da9063.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_MAX77663) += max77663_regulator.o
+obj-$(CONFIG_$(XPL_)REGULATOR_AXP) += axp_regulator.o
+obj-$(CONFIG_$(XPL_)REGULATOR_AXP_USB_POWER) += axp_usb_power.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_DA9063) += da9063.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_MAX77663) += max77663_regulator.o
obj-$(CONFIG_DM_REGULATOR_MAX77686) += max77686.o
obj-$(CONFIG_DM_REGULATOR_NPCM8XX) += npcm8xx_regulator.o
-obj-$(CONFIG_$(SPL_)DM_PMIC_PFUZE100) += pfuze100.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_BD71837) += bd71837.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_PCA9450) += pca9450.o
-obj-$(CONFIG_$(SPL_)REGULATOR_PWM) += pwm_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_FAN53555) += fan53555.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_COMMON) += regulator_common.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_FIXED) += fixed.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_GPIO) += gpio-regulator.o
+obj-$(CONFIG_$(XPL_)DM_PMIC_PFUZE100) += pfuze100.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_BD71837) += bd71837.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_PCA9450) += pca9450.o
+obj-$(CONFIG_$(XPL_)REGULATOR_PWM) += pwm_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_FAN53555) += fan53555.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_COMMON) += regulator_common.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_FIXED) += fixed.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_GPIO) += gpio-regulator.o
obj-$(CONFIG_DM_REGULATOR_QCOM_RPMH) += qcom-rpmh-regulator.o
obj-$(CONFIG_$(SPL_TPL_)REGULATOR_RK8XX) += rk8xx.o
obj-$(CONFIG_DM_REGULATOR_S2MPS11) += s2mps11_regulator.o
obj-$(CONFIG_REGULATOR_S5M8767) += s5m8767.o
obj-$(CONFIG_DM_REGULATOR_SANDBOX) += sandbox.o
obj-$(CONFIG_REGULATOR_TPS65090) += tps65090_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_PALMAS) += palmas_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_PBIAS) += pbias_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP873X) += lp873x_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_LP87565) += lp87565_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_PALMAS) += palmas_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_PBIAS) += pbias_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_LP873X) += lp873x_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_LP87565) += lp87565_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_STM32_VREFBUF) += stm32-vrefbuf.o
obj-$(CONFIG_DM_REGULATOR_TPS65910) += tps65910_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_TPS65911) += tps65911_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_TPS65911) += tps65911_regulator.o
obj-$(CONFIG_DM_REGULATOR_TPS62360) += tps62360_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_TPS6287X) += tps6287x_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_TPS80031) += tps80031_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_STPMIC1) += stpmic1.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_TPS6287X) += tps6287x_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_TPS80031) += tps80031_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_STPMIC1) += stpmic1.o
obj-$(CONFIG_DM_REGULATOR_TPS65941) += tps65941_regulator.o
obj-$(CONFIG_DM_REGULATOR_SCMI) += scmi_regulator.o
-obj-$(CONFIG_$(SPL_)DM_REGULATOR_ANATOP) += anatop_regulator.o
+obj-$(CONFIG_$(XPL_)DM_REGULATOR_ANATOP) += anatop_regulator.o
obj-$(CONFIG_DM_REGULATOR_TPS65219) += tps65219_regulator.o
diff --git a/drivers/remoteproc/Makefile b/drivers/remoteproc/Makefile
index e09ed1aa4d4..801b0965e4f 100644
--- a/drivers/remoteproc/Makefile
+++ b/drivers/remoteproc/Makefile
@@ -4,7 +4,7 @@
# Texas Instruments Incorporated - https://www.ti.com/
#
-obj-$(CONFIG_$(SPL_)REMOTEPROC) += rproc-uclass.o rproc-elf-loader.o
+obj-$(CONFIG_$(XPL_)REMOTEPROC) += rproc-uclass.o rproc-elf-loader.o
# Remote proc drivers - Please keep this list alphabetically sorted.
obj-$(CONFIG_K3_SYSTEM_CONTROLLER) += k3_system_controller.o
diff --git a/drivers/serial/Makefile b/drivers/serial/Makefile
index 66bd30b837b..1c0b013eb1f 100644
--- a/drivers/serial/Makefile
+++ b/drivers/serial/Makefile
@@ -11,7 +11,7 @@ endif
obj-$(CONFIG_PL01X_SERIAL) += serial_pl01x.o
obj-$(CONFIG_PL011_SERIAL) += serial_pl01x.o
-obj-$(CONFIG_$(SPL_)SYS_NS16550_SERIAL) += serial_ns16550.o
+obj-$(CONFIG_$(XPL_)SYS_NS16550_SERIAL) += serial_ns16550.o
obj-$(CONFIG_ALTERA_UART) += altera_uart.o
obj-$(CONFIG_ALTERA_JTAG_UART) += altera_jtag_uart.o
diff --git a/drivers/timer/Makefile b/drivers/timer/Makefile
index fec4af392e6..7a847e8388b 100644
--- a/drivers/timer/Makefile
+++ b/drivers/timer/Makefile
@@ -5,14 +5,14 @@
obj-y += timer-uclass.o
obj-$(CONFIG_ADI_SC5XX_TIMER) += adi_sc5xx_timer.o
obj-$(CONFIG_ALTERA_TIMER) += altera_timer.o
-obj-$(CONFIG_$(SPL_)ANDES_PLMT_TIMER) += andes_plmt_timer.o
+obj-$(CONFIG_$(XPL_)ANDES_PLMT_TIMER) += andes_plmt_timer.o
obj-$(CONFIG_ARC_TIMER) += arc_timer.o
obj-$(CONFIG_ARM_TWD_TIMER) += arm_twd_timer.o
obj-$(CONFIG_AST_TIMER) += ast_timer.o
obj-$(CONFIG_AST_IBEX_TIMER) += ast_ibex_timer.o
obj-$(CONFIG_ATCPIT100_TIMER) += atcpit100_timer.o
-obj-$(CONFIG_$(SPL_)ATMEL_PIT_TIMER) += atmel_pit_timer.o
-obj-$(CONFIG_$(SPL_)ATMEL_TCB_TIMER) += atmel_tcb_timer.o
+obj-$(CONFIG_$(XPL_)ATMEL_PIT_TIMER) += atmel_pit_timer.o
+obj-$(CONFIG_$(XPL_)ATMEL_TCB_TIMER) += atmel_tcb_timer.o
obj-$(CONFIG_CADENCE_TTC_TIMER) += cadence-ttc.o
obj-$(CONFIG_DESIGNWARE_APB_TIMER) += dw-apb-timer.o
obj-$(CONFIG_FTTMR010_TIMER) += fttmr010_timer.o
@@ -27,7 +27,7 @@ obj-$(CONFIG_RISCV_TIMER) += riscv_timer.o
obj-$(CONFIG_ROCKCHIP_TIMER) += rockchip_timer.o
obj-$(CONFIG_SANDBOX_TIMER) += sandbox_timer.o
obj-$(CONFIG_SP804_TIMER) += sp804_timer.o
-obj-$(CONFIG_$(SPL_)RISCV_ACLINT) += riscv_aclint_timer.o
+obj-$(CONFIG_$(XPL_)RISCV_ACLINT) += riscv_aclint_timer.o
obj-$(CONFIG_ARM_GLOBAL_TIMER) += arm_global_timer.o
obj-$(CONFIG_STM32_TIMER) += stm32_timer.o
obj-$(CONFIG_TEGRA_TIMER) += tegra-timer.o
diff --git a/drivers/usb/cdns3/Makefile b/drivers/usb/cdns3/Makefile
index 18d7190755d..d6047856091 100644
--- a/drivers/usb/cdns3/Makefile
+++ b/drivers/usb/cdns3/Makefile
@@ -4,8 +4,8 @@ cdns3-y := core.o drd.o
obj-$(CONFIG_USB_CDNS3) += cdns3.o
-cdns3-$(CONFIG_$(SPL_)USB_CDNS3_GADGET) += gadget.o ep0.o
+cdns3-$(CONFIG_$(XPL_)USB_CDNS3_GADGET) += gadget.o ep0.o
-cdns3-$(CONFIG_$(SPL_)USB_CDNS3_HOST) += host.o
+cdns3-$(CONFIG_$(XPL_)USB_CDNS3_HOST) += host.o
obj-$(CONFIG_USB_CDNS3_TI) += cdns3-ti.o
diff --git a/drivers/usb/common/Makefile b/drivers/usb/common/Makefile
index 2e9353b76a6..11cc4657a0f 100644
--- a/drivers/usb/common/Makefile
+++ b/drivers/usb/common/Makefile
@@ -3,7 +3,7 @@
# (C) Copyright 2016 Freescale Semiconductor, Inc.
#
-obj-$(CONFIG_$(SPL_)DM_USB) += common.o
+obj-$(CONFIG_$(XPL_)DM_USB) += common.o
obj-$(CONFIG_USB_ISP1760) += usb_urb.o
obj-$(CONFIG_USB_MUSB_HOST) += usb_urb.o
obj-$(CONFIG_USB_MUSB_GADGET) += usb_urb.o
diff --git a/drivers/usb/dwc3/Makefile b/drivers/usb/dwc3/Makefile
index a46b6824ab7..a085c9d4628 100644
--- a/drivers/usb/dwc3/Makefile
+++ b/drivers/usb/dwc3/Makefile
@@ -6,11 +6,11 @@ dwc3-y := core.o
obj-$(CONFIG_USB_DWC3_GADGET) += gadget.o ep0.o
-obj-$(CONFIG_$(SPL_)USB_DWC3_AM62) += dwc3-am62.o
+obj-$(CONFIG_$(XPL_)USB_DWC3_AM62) += dwc3-am62.o
obj-$(CONFIG_USB_DWC3_OMAP) += dwc3-omap.o
obj-$(CONFIG_USB_DWC3_MESON_G12A) += dwc3-meson-g12a.o
obj-$(CONFIG_USB_DWC3_MESON_GXL) += dwc3-meson-gxl.o
-obj-$(CONFIG_$(SPL_)USB_DWC3_GENERIC) += dwc3-generic.o
+obj-$(CONFIG_$(XPL_)USB_DWC3_GENERIC) += dwc3-generic.o
obj-$(CONFIG_USB_DWC3_UNIPHIER) += dwc3-uniphier.o
obj-$(CONFIG_USB_DWC3_LAYERSCAPE) += dwc3-layerscape.o
obj-$(CONFIG_USB_DWC3_PHY_OMAP) += ti_usb_phy.o
diff --git a/drivers/usb/gadget/udc/Makefile b/drivers/usb/gadget/udc/Makefile
index 467c566f6d3..4b6a8fdfeee 100644
--- a/drivers/usb/gadget/udc/Makefile
+++ b/drivers/usb/gadget/udc/Makefile
@@ -2,9 +2,9 @@
#
# USB peripheral controller drivers
-ifndef CONFIG_$(SPL_)DM_USB_GADGET
+ifndef CONFIG_$(XPL_)DM_USB_GADGET
obj-$(CONFIG_USB_DWC3_GADGET) += udc-core.o
endif
-obj-$(CONFIG_$(SPL_)DM_USB_GADGET) += udc-core.o
+obj-$(CONFIG_$(XPL_)DM_USB_GADGET) += udc-core.o
obj-y += udc-uclass.o
diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index 8dad36f9369..07deb4fadd6 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -3,7 +3,7 @@
# (C) Copyright 2000-2007
# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
-ifdef CONFIG_$(SPL_)DM_USB
+ifdef CONFIG_$(XPL_)DM_USB
obj-y += usb-uclass.o
obj-$(CONFIG_SANDBOX) += usb-sandbox.o
endif
diff --git a/drivers/video/Makefile b/drivers/video/Makefile
index f3f70cd04a1..93fed8c491a 100644
--- a/drivers/video/Makefile
+++ b/drivers/video/Makefile
@@ -34,7 +34,7 @@ obj-${CONFIG_EXYNOS_FB} += exynos/
obj-${CONFIG_VIDEO_ROCKCHIP} += rockchip/
obj-${CONFIG_VIDEO_STM32} += stm32/
obj-${CONFIG_VIDEO_TEGRA124} += tegra124/
-obj-${CONFIG_$(SPL_)VIDEO_TIDSS} += tidss/
+obj-${CONFIG_$(XPL_)VIDEO_TIDSS} += tidss/
obj-y += ti/
obj-$(CONFIG_ATMEL_HLCD) += atmel_hlcdfb.o
diff --git a/drivers/video/tidss/Makefile b/drivers/video/tidss/Makefile
index a29cee2a414..f0cbe1d4ed1 100644
--- a/drivers/video/tidss/Makefile
+++ b/drivers/video/tidss/Makefile
@@ -9,4 +9,4 @@
# Author: Tomi Valkeinen <tomi.valkeinen at ti.com>
-obj-${CONFIG_$(SPL_)VIDEO_TIDSS} = tidss_drv.o
+obj-${CONFIG_$(XPL_)VIDEO_TIDSS} = tidss_drv.o
diff --git a/fs/fat/Makefile b/fs/fat/Makefile
index f84efaccc75..7414b3602aa 100644
--- a/fs/fat/Makefile
+++ b/fs/fat/Makefile
@@ -1,5 +1,5 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_$(SPL_)FS_FAT) = fat.o
-obj-$(CONFIG_$(SPL_)FAT_WRITE) = fat_write.o
+obj-$(CONFIG_$(XPL_)FS_FAT) = fat.o
+obj-$(CONFIG_$(XPL_)FAT_WRITE) = fat_write.o
diff --git a/fs/squashfs/Makefile b/fs/squashfs/Makefile
index ba66ee821c2..0772e1a497d 100644
--- a/fs/squashfs/Makefile
+++ b/fs/squashfs/Makefile
@@ -1,7 +1,7 @@
# SPDX-License-Identifier: GPL-2.0+
#
-obj-$(CONFIG_$(SPL_)FS_SQUASHFS) = sqfs.o \
+obj-$(CONFIG_$(XPL_)FS_SQUASHFS) = sqfs.o \
sqfs_inode.o \
sqfs_dir.o \
sqfs_decompressor.o
diff --git a/lib/Makefile b/lib/Makefile
index 66f84408aae..139476a4a23 100644
--- a/lib/Makefile
+++ b/lib/Makefile
@@ -71,25 +71,25 @@ obj-$(CONFIG_$(SPL_TPL_)CRC16) += crc16.o
obj-y += crypto/
obj-$(CONFIG_$(SPL_TPL_)ACPI) += acpi/
-obj-$(CONFIG_$(SPL_)MD5) += md5.o
+obj-$(CONFIG_$(XPL_)MD5) += md5.o
obj-$(CONFIG_ECDSA) += ecdsa/
-obj-$(CONFIG_$(SPL_)RSA) += rsa/
+obj-$(CONFIG_$(XPL_)RSA) += rsa/
obj-$(CONFIG_HASH) += hash-checksum.o
obj-$(CONFIG_BLAKE2) += blake2/blake2b.o
-obj-$(CONFIG_$(SPL_)SHA1) += sha1.o
-obj-$(CONFIG_$(SPL_)SHA256) += sha256.o
-obj-$(CONFIG_$(SPL_)SHA512) += sha512.o
+obj-$(CONFIG_$(XPL_)SHA1) += sha1.o
+obj-$(CONFIG_$(XPL_)SHA256) += sha256.o
+obj-$(CONFIG_$(XPL_)SHA512) += sha512.o
obj-$(CONFIG_CRYPT_PW) += crypt/
-obj-$(CONFIG_$(SPL_)ASN1_DECODER) += asn1_decoder.o
+obj-$(CONFIG_$(XPL_)ASN1_DECODER) += asn1_decoder.o
-obj-$(CONFIG_$(SPL_)ZLIB) += zlib/
-obj-$(CONFIG_$(SPL_)ZSTD) += zstd/
-obj-$(CONFIG_$(SPL_)GZIP) += gunzip.o
-obj-$(CONFIG_$(SPL_)LZO) += lzo/
-obj-$(CONFIG_$(SPL_)LZMA) += lzma/
-obj-$(CONFIG_$(SPL_)LZ4) += lz4_wrapper.o
+obj-$(CONFIG_$(XPL_)ZLIB) += zlib/
+obj-$(CONFIG_$(XPL_)ZSTD) += zstd/
+obj-$(CONFIG_$(XPL_)GZIP) += gunzip.o
+obj-$(CONFIG_$(XPL_)LZO) += lzo/
+obj-$(CONFIG_$(XPL_)LZMA) += lzma/
+obj-$(CONFIG_$(XPL_)LZ4) += lz4_wrapper.o
-obj-$(CONFIG_$(SPL_)LIB_RATIONAL) += rational.o
+obj-$(CONFIG_$(XPL_)LIB_RATIONAL) += rational.o
obj-$(CONFIG_LIBAVB) += libavb/
@@ -144,7 +144,7 @@ else
obj-y += vsprintf.o strto.o
obj-$(CONFIG_SSCANF) += sscanf.o
endif
-obj-$(CONFIG_$(SPL_)OID_REGISTRY) += oid_registry.o
+obj-$(CONFIG_$(XPL_)OID_REGISTRY) += oid_registry.o
obj-y += abuf.o
obj-y += alist.o
diff --git a/lib/acpi/Makefile b/lib/acpi/Makefile
index cc2868488a0..99be19adb4c 100644
--- a/lib/acpi/Makefile
+++ b/lib/acpi/Makefile
@@ -5,10 +5,10 @@ obj-y += acpi.o
ifdef CONFIG_$(SPL_TPL_)GENERATE_ACPI_TABLE
-obj-$(CONFIG_$(SPL_)ACPIGEN) += acpigen.o
-obj-$(CONFIG_$(SPL_)ACPIGEN) += acpi_device.o
-obj-$(CONFIG_$(SPL_)ACPIGEN) += acpi_dp.o
-obj-$(CONFIG_$(SPL_)ACPIGEN) += acpi_table.o
+obj-$(CONFIG_$(XPL_)ACPIGEN) += acpigen.o
+obj-$(CONFIG_$(XPL_)ACPIGEN) += acpi_device.o
+obj-$(CONFIG_$(XPL_)ACPIGEN) += acpi_dp.o
+obj-$(CONFIG_$(XPL_)ACPIGEN) += acpi_table.o
obj-y += acpi_writer.o
# With QEMU the ACPI tables come from there, not from U-Boot
diff --git a/lib/aes/Makefile b/lib/aes/Makefile
index daed52a713b..ad6228a7dad 100644
--- a/lib/aes/Makefile
+++ b/lib/aes/Makefile
@@ -2,4 +2,4 @@
#
# Copyright (c) 2019, Softathome
-obj-$(CONFIG_$(SPL_)FIT_CIPHER) += aes-decrypt.o
+obj-$(CONFIG_$(XPL_)FIT_CIPHER) += aes-decrypt.o
diff --git a/lib/crypto/Makefile b/lib/crypto/Makefile
index 3259c951241..de1510d3eb5 100644
--- a/lib/crypto/Makefile
+++ b/lib/crypto/Makefile
@@ -3,16 +3,16 @@
# Makefile for asymmetric cryptographic keys
#
-obj-$(CONFIG_$(SPL_)ASYMMETRIC_KEY_TYPE) += asymmetric_keys.o
+obj-$(CONFIG_$(XPL_)ASYMMETRIC_KEY_TYPE) += asymmetric_keys.o
asymmetric_keys-y := asymmetric_type.o
-obj-$(CONFIG_$(SPL_)ASYMMETRIC_PUBLIC_KEY_SUBTYPE) += public_key.o
+obj-$(CONFIG_$(XPL_)ASYMMETRIC_PUBLIC_KEY_SUBTYPE) += public_key.o
#
# RSA public key parser
#
-obj-$(CONFIG_$(SPL_)RSA_PUBLIC_KEY_PARSER) += rsa_public_key.o
+obj-$(CONFIG_$(XPL_)RSA_PUBLIC_KEY_PARSER) += rsa_public_key.o
rsa_public_key-y := \
rsapubkey.asn1.o \
rsa_helper.o
@@ -30,7 +30,7 @@ endif
#
# X.509 Certificate handling
#
-obj-$(CONFIG_$(SPL_)X509_CERTIFICATE_PARSER) += x509_key_parser.o
+obj-$(CONFIG_$(XPL_)X509_CERTIFICATE_PARSER) += x509_key_parser.o
x509_key_parser-y := \
x509.asn1.o \
x509_akid.asn1.o \
@@ -47,11 +47,11 @@ $(obj)/x509_akid.asn1.o: $(obj)/x509_akid.asn1.c $(obj)/x509_akid.asn1.h
#
# PKCS#7 message handling
#
-obj-$(CONFIG_$(SPL_)PKCS7_MESSAGE_PARSER) += pkcs7_message.o
+obj-$(CONFIG_$(XPL_)PKCS7_MESSAGE_PARSER) += pkcs7_message.o
pkcs7_message-y := \
pkcs7.asn1.o \
pkcs7_parser.o
-obj-$(CONFIG_$(SPL_)PKCS7_VERIFY) += pkcs7_verify.o
+obj-$(CONFIG_$(XPL_)PKCS7_VERIFY) += pkcs7_verify.o
$(obj)/pkcs7_parser.o: $(obj)/pkcs7.asn1.h
$(obj)/pkcs7.asn1.o: $(obj)/pkcs7.asn1.c $(obj)/pkcs7.asn1.h
@@ -59,7 +59,7 @@ $(obj)/pkcs7.asn1.o: $(obj)/pkcs7.asn1.c $(obj)/pkcs7.asn1.h
#
# Signed PE binary-wrapped key handling
#
-obj-$(CONFIG_$(SPL_)MSCODE_PARSER) += mscode.o
+obj-$(CONFIG_$(XPL_)MSCODE_PARSER) += mscode.o
mscode-y := \
mscode_parser.o \
diff --git a/lib/ecdsa/Makefile b/lib/ecdsa/Makefile
index 771d6d3135b..32b6183f6ff 100644
--- a/lib/ecdsa/Makefile
+++ b/lib/ecdsa/Makefile
@@ -1 +1 @@
-obj-$(CONFIG_$(SPL_)ECDSA_VERIFY) += ecdsa-verify.o
+obj-$(CONFIG_$(XPL_)ECDSA_VERIFY) += ecdsa-verify.o
diff --git a/net/Makefile b/net/Makefile
index 64ab7ec740a..a1d37855593 100644
--- a/net/Makefile
+++ b/net/Makefile
@@ -10,14 +10,14 @@ obj-$(CONFIG_CMD_BOOTP) += bootp.o
obj-$(CONFIG_CMD_CDP) += cdp.o
obj-$(CONFIG_CMD_DNS) += dns.o
obj-$(CONFIG_DM_DSA) += dsa-uclass.o
-obj-$(CONFIG_$(SPL_)DM_ETH) += eth-uclass.o
+obj-$(CONFIG_$(XPL_)DM_ETH) += eth-uclass.o
obj-$(CONFIG_$(SPL_TPL_)BOOTDEV_ETH) += eth_bootdev.o
obj-$(CONFIG_DM_MDIO) += mdio-uclass.o
obj-$(CONFIG_DM_MDIO_MUX) += mdio-mux-uclass.o
-obj-$(CONFIG_$(SPL_)DM_ETH) += eth_common.o
+obj-$(CONFIG_$(XPL_)DM_ETH) += eth_common.o
obj-$(CONFIG_CMD_LINK_LOCAL) += link_local.o
obj-$(CONFIG_IPV6) += ndisc.o
-obj-$(CONFIG_$(SPL_)DM_ETH) += net.o
+obj-$(CONFIG_$(XPL_)DM_ETH) += net.o
obj-$(CONFIG_IPV6) += net6.o
obj-$(CONFIG_CMD_NFS) += nfs.o
obj-$(CONFIG_CMD_PING) += ping.o
diff --git a/scripts/Kbuild.include b/scripts/Kbuild.include
index b70b75ee68d..1a6b28feedf 100644
--- a/scripts/Kbuild.include
+++ b/scripts/Kbuild.include
@@ -325,7 +325,7 @@ endif
.SECONDARY:
ifdef CONFIG_XPL_BUILD
-SPL_ := SPL_
+XPL_ := SPL_
ifeq ($(CONFIG_VPL_BUILD),y)
SPL_TPL_ := VPL_
else
@@ -336,6 +336,6 @@ SPL_TPL_ := SPL_
endif
endif
else
-SPL_ :=
+XPL_ :=
SPL_TPL_ :=
endif
diff --git a/scripts/Makefile.xpl b/scripts/Makefile.xpl
index b43ff998679..11ae93f8556 100644
--- a/scripts/Makefile.xpl
+++ b/scripts/Makefile.xpl
@@ -59,7 +59,7 @@ endif
export SPL_NAME
ifdef CONFIG_XPL_BUILD
-SPL_ := SPL_
+XPL_ := SPL_
ifeq ($(CONFIG_VPL_BUILD),y)
SPL_TPL_ := VPL_
else
@@ -70,7 +70,7 @@ SPL_TPL_ := SPL_
endif
endif
else
-SPL_ :=
+XPL_ :=
SPL_TPL_ :=
endif
diff --git a/test/Makefile b/test/Makefile
index f801d87e385..145c952d2c3 100644
--- a/test/Makefile
+++ b/test/Makefile
@@ -4,24 +4,24 @@
obj-y += test-main.o
-ifneq ($(CONFIG_$(SPL_)BLOBLIST),)
-obj-$(CONFIG_$(SPL_)CMDLINE) += bloblist.o
-obj-$(CONFIG_$(SPL_)CMDLINE) += bootm.o
+ifneq ($(CONFIG_$(XPL_)BLOBLIST),)
+obj-$(CONFIG_$(XPL_)CMDLINE) += bloblist.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += bootm.o
endif
-obj-$(CONFIG_$(SPL_)CMDLINE) += cmd/
-obj-$(CONFIG_$(SPL_)CMDLINE) += cmd_ut.o
-obj-$(CONFIG_$(SPL_)CMDLINE) += command_ut.o
-obj-$(CONFIG_$(SPL_)UT_COMPRESSION) += compression.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += cmd/
+obj-$(CONFIG_$(XPL_)CMDLINE) += cmd_ut.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += command_ut.o
+obj-$(CONFIG_$(XPL_)UT_COMPRESSION) += compression.o
obj-y += dm/
obj-$(CONFIG_FUZZ) += fuzz/
ifndef CONFIG_SANDBOX_VPL
obj-$(CONFIG_UNIT_TEST) += lib/
endif
ifneq ($(CONFIG_HUSH_PARSER),)
-obj-$(CONFIG_$(SPL_)CMDLINE) += hush/
+obj-$(CONFIG_$(XPL_)CMDLINE) += hush/
endif
-obj-$(CONFIG_$(SPL_)CMDLINE) += print_ut.o
-obj-$(CONFIG_$(SPL_)CMDLINE) += str_ut.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += print_ut.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += str_ut.o
obj-$(CONFIG_UT_TIME) += time_ut.o
obj-y += ut.o
@@ -29,7 +29,7 @@ ifeq ($(CONFIG_XPL_BUILD),)
obj-y += boot/
obj-$(CONFIG_UNIT_TEST) += common/
obj-y += log/
-obj-$(CONFIG_$(SPL_)UT_UNICODE) += unicode_ut.o
+obj-$(CONFIG_$(XPL_)UT_UNICODE) += unicode_ut.o
else
obj-$(CONFIG_SPL_UT_LOAD) += image/
endif
diff --git a/test/fuzz/Makefile b/test/fuzz/Makefile
index 663b79ce80b..8a135b65e4b 100644
--- a/test/fuzz/Makefile
+++ b/test/fuzz/Makefile
@@ -4,5 +4,5 @@
# Written by Andrew Scull <ascull at google.com>
#
-obj-$(CONFIG_$(SPL_)CMDLINE) += cmd_fuzz.o
+obj-$(CONFIG_$(XPL_)CMDLINE) += cmd_fuzz.o
obj-$(CONFIG_VIRTIO_SANDBOX) += virtio.o
diff --git a/tools/qconfig.py b/tools/qconfig.py
index 71e911eeb3b..e025f560928 100755
--- a/tools/qconfig.py
+++ b/tools/qconfig.py
@@ -1220,8 +1220,8 @@ def scan_makefiles(fnames):
>>> RE_MK_CONFIGS.search('CONFIG_FRED').groups()
(None, 'FRED')
- >>> RE_MK_CONFIGS.search('CONFIG_$(SPL_)MARY').groups()
- ('$(SPL_)', 'MARY')
+ >>> RE_MK_CONFIGS.search('CONFIG_$(XPL_)MARY').groups()
+ ('$(XPL_)', 'MARY')
>>> RE_MK_CONFIGS.search('CONFIG_$(SPL_TPL_)MARY').groups()
('$(SPL_TPL_)', 'MARY')
"""
@@ -1321,7 +1321,7 @@ def do_scan_source(path, do_update):
spl_mode (int): If MODE_SPL, look at source code which implies
an SPL_ option, but for which there is none;
for MOD_PROPER, look at source code which implies a Proper
- option (i.e. use of CONFIG_IS_ENABLED() or $(SPL_) or
+ option (i.e. use of CONFIG_IS_ENABLED() or $(XPL_) or
$(SPL_TPL_) but for which there none;
if MODE_NORMAL, ignore SPL
--
2.34.1
More information about the U-Boot
mailing list