[PATCH 1/2] doc: efi_loader: Tidy up the bootefi-command docs

[Heinrich Schuchardt]

On 6/1/25 14:04, Simon Glass wrote:
> There are backslashes in some of the tags which seems to be unnecessary.
> Remove then.
> 
> Change the word 'either' to 'any' since there are three options.
> 
> Signed-off-by: Simon Glass <sjg at chromium.org>

Reviewed-by: Heinrich Schuchardt <xypron.glpk at gmx.de>

> ---
> 
>   doc/usage/cmd/bootefi.rst | 20 ++++++++++----------
>   1 file changed, 10 insertions(+), 10 deletions(-)
> 
> diff --git a/doc/usage/cmd/bootefi.rst b/doc/usage/cmd/bootefi.rst
> index 3efe9e9df57..d6e4e62e383 100644
> --- a/doc/usage/cmd/bootefi.rst
> +++ b/doc/usage/cmd/bootefi.rst
> @@ -20,19 +20,19 @@ Synopsis
>   Description
>   -----------
>   
> -The *bootefi* command is used to launch a UEFI binary which can be either of
> +The *bootefi* command is used to launch a UEFI binary which can be any of
>   
>   * UEFI application
>   * UEFI boot services driver
>   * UEFI run-time services driver
>   
>   An operating system requires a hardware description which can either be
> -presented as ACPI table (CONFIG\_GENERATE\_ACPI\_TABLE=y) or as device-tree.
> -The load address of the device-tree may be provided as parameter *fdt\_addr*. If
> +presented as ACPI table (CONFIG_GENERATE_ACPI_TABLE=y) or as device-tree.
> +The load address of the device-tree may be provided as parameter *fdt_addr*. If
>   this address is not specified, the bootefi command will try to fall back in
>   sequence to:
>   
> -* the device-tree specified by environment variable *fdt\_addr*
> +* the device-tree specified by environment variable *fdt_addr*
>   * the device-tree specified by environment variable *fdtcontroladdr*
>   
>   The load address of the binary is specified by parameter *image_address*. A
> @@ -110,7 +110,7 @@ U-Boot can be compiled with UEFI unit tests. These unit tests are invoked using
>   the *bootefi selftest* sub-command.
>   
>   Which unit test is executed is controlled by the environment variable
> -*efi\_selftest*. If this variable is not set, all unit tests that are not marked
> +*efi_selftest*. If this variable is not set, all unit tests that are not marked
>   as 'on request' are executed.
>   
>   To show a list of the available unit tests the value *list* can be used
> @@ -126,7 +126,7 @@ To show a list of the available unit tests the value *list* can be used
>       'configuration tables'
>       ...
>   
> -A single test is selected for execution by setting the *efi\_selftest*
> +A single test is selected for execution by setting the *efi_selftest*
>   environment variable to match one of the listed identifiers
>   
>   ::
> @@ -140,10 +140,10 @@ return to the command line but require a board reset.
>   Configuration
>   -------------
>   
> -To use the *bootefi* command you must specify CONFIG\_CMD\_BOOTEFI=y.
> -The *bootefi bootmgr* sub-command requries CMD\_BOOTEFI\_BOOTMGR=y.
> -The *bootefi hello* sub-command requries CMD\_BOOTEFI\_HELLO=y.
> -The *bootefi selftest* sub-command depends on CMD\_BOOTEFI\_SELFTEST=y.
> +To use the *bootefi* command you must specify CONFIG_CMD_BOOTEFI=y.
> +The *bootefi bootmgr* sub-command requries CMD_BOOTEFI_BOOTMGR=y.
> +The *bootefi hello* sub-command requries CMD_BOOTEFI_HELLO=y.
> +The *bootefi selftest* sub-command depends on CMD_BOOTEFI_SELFTEST=y.
>   
>   See also
>   --------