[PATCH] spl: Add generic SPL MTD loader support
Sean Anderson
seanga2 at gmail.com
Tue Feb 17 16:13:43 CET 2026
On 2/17/26 10:11, Sean Anderson wrote:
> On 2/11/26 17:25, Fabio Estevam wrote:
>> From: Fabio Estevam <festevam at nabladev.com>
>>
>> Add support for loading the next stage from an MTD device in SPL.
>>
>> Introduce CONFIG_SPL_MTD_LOAD and a generic SPL MTD loader
>> implementation that uses the MTD subsystem to read the U-Boot payload.
>>
>> The loader works with any MTD-backed storage, including raw NAND and
>> SPI NAND, without being tied to a specific NAND type.
>>
>> The payload offset defaults to CONFIG_SYS_MTD_U_BOOT_OFFS and can be
>> overridden via the device tree property:
>>
>> u-boot,spl-payload-offset
>>
>> To support both raw NAND and SPI NAND boot flows, the loader is
>> registered for BOOT_DEVICE_NAND and BOOT_DEVICE_SPI. This allows it
>> to operate correctly on platforms where the ROM reports either NAND
>> or SPI as the boot source while using the same MTD-based loading
>> infrastructure.
>>
>> The required NAND core and SPI NAND drivers are built for SPL when
>> CONFIG_SPL_MTD_LOAD is enabled.
>>
>> This provides reusable infrastructure for boards that boot from MTD
>> devices without relying on SPI-specific or NAND-specific SPL loaders.
>>
>> Signed-off-by: Fabio Estevam <festevam at nabladev.com>
>
> Thanks for putting this together. For platforms that have the space this
> is definitely the way to go.
>
>> ---
>> Dinesh,
>>
>> Could you please test this approach on your boards?
>>
>> Thanks
>>
>> common/spl/Kconfig | 15 +++++++
>> common/spl/Makefile | 1 +
>> common/spl/spl_mtd.c | 88 +++++++++++++++++++++++++++++++++++++++
>> drivers/mtd/Makefile | 1 +
>> drivers/mtd/nand/Makefile | 12 +++++-
>> 5 files changed, 116 insertions(+), 1 deletion(-)
>> create mode 100644 common/spl/spl_mtd.c
>>
>> diff --git a/common/spl/Kconfig b/common/spl/Kconfig
>> index 2998b7acb75f..2aba6da73c10 100644
>> --- a/common/spl/Kconfig
>> +++ b/common/spl/Kconfig
>> @@ -1576,8 +1576,23 @@ config SPL_SPI_LOAD
>> Enable support for loading next stage, U-Boot or otherwise, from
>> SPI NOR in U-Boot SPL.
>> +config SPL_MTD_LOAD
>> + bool "Support loading from a generic MTD device"
>> + depends on SPL
>> + depends on MTD && DM_MTD
>> + help
>> + Enable support for loading next stage, U-Boot or otherwise, from
>> + a generic MTD device (raw NAND, SPI NAND) in U-Boot SPL.
>> +
>> endif # SPL_SPI_FLASH_SUPPORT
>> +config SYS_MTD_U_BOOT_OFFS
>> + hex "address of u-boot payload in the MTD device"
>> + default 0x0
>> + help
>> + Address within the MTD device where the u-boot payload is fetched
>> + from.
>> +
>> config SYS_SPI_U_BOOT_OFFS
>> hex "address of u-boot payload in SPI flash"
>> default 0x8000 if ARCH_SUNXI
>> diff --git a/common/spl/Makefile b/common/spl/Makefile
>> index 4c9482bd3096..9f5ddcad17af 100644
>> --- a/common/spl/Makefile
>> +++ b/common/spl/Makefile
>> @@ -35,6 +35,7 @@ obj-$(CONFIG_$(PHASE_)NVME) += spl_nvme.o
>> obj-$(CONFIG_$(PHASE_)SEMIHOSTING) += spl_semihosting.o
>> obj-$(CONFIG_$(PHASE_)DFU) += spl_dfu.o
>> obj-$(CONFIG_$(PHASE_)SPI_LOAD) += spl_spi.o
>> +obj-$(CONFIG_$(PHASE_)MTD_LOAD) += spl_mtd.o
>> obj-$(CONFIG_$(PHASE_)RAM_SUPPORT) += spl_ram.o
>> obj-$(CONFIG_$(PHASE_)USB_SDP_SUPPORT) += spl_sdp.o
>> endif
>> diff --git a/common/spl/spl_mtd.c b/common/spl/spl_mtd.c
>> new file mode 100644
>> index 000000000000..8c6c94e592d0
>> --- /dev/null
>> +++ b/common/spl/spl_mtd.c
>> @@ -0,0 +1,88 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +
>> +/*
>> + * Generic SPL loader for MTD devices.
>> + *
>> + * Based on spl_spi.c, which is:
>> + *
>> + * Copyright (C) 2011 OMICRON electronics GmbH
>> + *
>> + * based on drivers/mtd/nand/raw/nand_spl_load.c
>> + *
>> + * Copyright (C) 2011
>> + * Heiko Schocher, DENX Software Engineering, hs at denx.de.
>> + */
>> +
>> +#include <config.h>
>> +#include <errno.h>
>> +#include <image.h>
>> +#include <log.h>
>> +#include <spl.h>
>> +#include <spl_load.h>
>> +
>> +#include <dm.h>
>> +#include <dm/ofnode.h>
>> +#include <dm/uclass.h>
>> +#include <mtd.h>
>> +
>> +static struct mtd_info *spl_mtd_get_device(void)
>> +{
>> + struct udevice *dev;
>> + int ret;
>> +
>> + for (ret = uclass_first_device_err(UCLASS_MTD, &dev);
>> + dev;
>> + ret = uclass_next_device_err(&dev)) {
>> + if (ret)
>> + continue;
>> +
>> + return dev_get_uclass_priv(dev);
>> + }
>
> I think this should be uclass_get_device_by_seq(UCLASS_MTD,
> CONFIG_SYS_MTD_SEQ) or use the above method if e.g.
> CONFIG_SYS_MTD_U_BOOT_OFFS is -1.
get_mtd_device(NULL, CONFIG_SYS_MTD_SEQ)
>> +
>> + return NULL;
>> +}
>> +
>> +static ulong spl_mtd_read(struct spl_load_info *load,
>> + ulong offs, ulong size, void *buf)
>> +{
>> + struct mtd_info *mtd = load->priv;
>> + size_t retlen;
>> + int ret;
>> +
>> + ret = mtd_read(mtd, offs, size, &retlen, buf);
>> + if (ret && !mtd_is_bitflip(ret))
>> + return 0;
>> +
>> + if (retlen != size)
>> + return 0;
>> +
>> + return retlen;
>> +}
>> +
>> +static int spl_mtd_load_image(struct spl_image_info *spl_image,
>> + struct spl_boot_device *bootdev)
>> +{
>> + struct spl_load_info load;
>> + struct mtd_info *mtd;
>> + ulong offset;
>> +
>> + mtd = spl_mtd_get_device();
>> + if (!mtd) {
>> + debug("No MTD device found\n");
>
> This should be a puts, as otherwise there will be no error printed at all.
>
>> + return -ENODEV;
>> + }
>> +
>> + spl_load_init(&load, spl_mtd_read, mtd, mtd->writesize);
>> +
>> + offset = CONFIG_SYS_MTD_U_BOOT_OFFS;
>> +
>> + if (CONFIG_IS_ENABLED(OF_REAL))
>> + offset = ofnode_conf_read_int("u-boot,spl-payload-offset",
>> + offset);
>> +
>> + return spl_load(spl_image, bootdev, &load, 0, offset);
>> +}
>> +
>> +/* Priority 1 so boards may override */
>> +SPL_LOAD_IMAGE_METHOD("MTD-NAND", 1, BOOT_DEVICE_NAND, spl_mtd_load_image);
>> +SPL_LOAD_IMAGE_METHOD("MTD-SPI-NAND", 1, BOOT_DEVICE_SPI, spl_mtd_load_image);
>> diff --git a/drivers/mtd/Makefile b/drivers/mtd/Makefile
>> index ce05e206073d..0856a8f68732 100644
>> --- a/drivers/mtd/Makefile
>> +++ b/drivers/mtd/Makefile
>> @@ -34,6 +34,7 @@ else
>> ifneq ($(mtd-y),)
>> obj-$(CONFIG_SPL_MTD) += mtd.o
>> endif
>> +obj-$(CONFIG_SPL_MTD_LOAD) += nand/
>
> You should add this to the list in include/spl_load.h.
>
>> obj-$(CONFIG_$(PHASE_)NAND_SUPPORT) += nand/
>> obj-$(CONFIG_SPL_ONENAND_SUPPORT) += onenand/
>> obj-$(CONFIG_$(PHASE_)SPI_FLASH_SUPPORT) += spi/
>> diff --git a/drivers/mtd/nand/Makefile b/drivers/mtd/nand/Makefile
>> index c8169cf73902..cd6eaa87739c 100644
>> --- a/drivers/mtd/nand/Makefile
>> +++ b/drivers/mtd/nand/Makefile
>> @@ -1,10 +1,20 @@
>> # SPDX-License-Identifier: GPL-2.0+
>> -ifeq ($(CONFIG_XPL_BUILD)$(CONFIG_TPL_BUILD),)
>> nandcore-objs := core.o bbt.o
>> +
>> +ifeq ($(CONFIG_XPL_BUILD),)
>> +
>> +# U-Boot proper
>> obj-$(CONFIG_MTD_NAND_CORE) += nandcore.o
>> obj-$(CONFIG_MTD_RAW_NAND) += raw/
>> obj-$(CONFIG_MTD_SPI_NAND) += spi/
>> +
>> else
>> +
>> +# XPL
>> +obj-$(CONFIG_SPL_MTD_LOAD) += nandcore.o
>> +obj-$(CONFIG_SPL_MTD_LOAD) += spi/
>
> This should be done in Kconfig. Some platforms may want to load from different
> MTD combinations, e.g. SPI nand and SPI nor.
>
>> +
>> +# raw NAND still follows the normal SPL rule
>> obj-$(CONFIG_$(PHASE_)NAND_SUPPORT) += raw/
>> endif
>
> Please add a test for this. You should be able to extend test/image/spl_load_spi.c
> and test/image/spl_load_nand.c
>
> --Sean
More information about the U-Boot
mailing list