[PATCH v7 00/22] VBE serial part H: Implement VBE on Rockchip RK3399
Simon Glass
sjg at chromium.org
Thu May 28 19:10:07 CEST 2026
This series largely completes the work to enable VBE on a suitable
board. Most of it is rockchip-specific patches to support the VPL phase,
i.e. the one which decides which boot patch to take (A, B or recovery).
A good chunk of this series is adding an image for VBE, by creating a
new Binman image. Future work in Binman may make this more automated /
easier, but for now it is written out in full. The work is undertaken
piecemeal so it is easier to review the steps.
VBE allows similar boards to share firmware images, with perhaps just
TPL (around 75K) being different for each board. Using a common image
for VPL, SPL and U-Boot saves a lot of space in the image and makes
builds easier. Perhaps more importantly it means that both SPL and
U-Boot proper can be safely updated (with VBE's A/B mechanism) in the
field.
Of course, each board still needs a separate devicetree.
The current bloblist implementation has a few problems which need to be
resolved. I will sort this out separately so as to coordinate with
Ilias' global_data changes.
Here is the layout of the image:
Name Image-pos Size Entry-type Offset Uncomp-size
----------------------------------------------------------------------------------------------
image 0 1b960cf section 0
alternates-fdt 8000 31000 alternates-fdt 8000
mkimage 8000 31000 mkimage 0
u-boot-tpl 8048 12a11 u-boot-tpl 48
vpl 208000 16200 fit 208000
image-vpl 209400 a5a3 section 1400
section 209400 a5a3 section 0
u-boot-vpl-nodtb 10348 u-boot-vpl-nodtb 0
u-boot-vpl-bss-pad 20 u-boot-vpl-bss-pad 10348
@fdt-SEQ 0 0 section 0
vbe-a 800000 39b200 section 800000
spl-a 800000 100000 fit 0
spl 801400 10c97 section 1400
section 801400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
@fdt-SEQ 0 0 section 0
u-boot-a 900000 29b200 fit 100000
spl 902400 10c97 section 2400
section 902400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
u-boot 913200 e4250 section 13200
u-boot-nodtb 913200 e4250 u-boot-nodtb 0
@atf-SEQ 0 0 section 0
atf-bl31 0 0 atf-bl31 0
@tee-SEQ 0 0 section 0
tee-os 0 0 tee-os 0
@fdt-SEQ 0 0 section 0
vbe-b 1000000 39b200 section 1000000
spl-b 1000000 100000 fit 0
spl 1001400 10c97 section 1400
section 1001400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
@fdt-SEQ 0 0 section 0
u-boot-b 1100000 29b200 fit 100000
spl 1102400 10c97 section 2400
section 1102400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
u-boot 1113200 e4250 section 13200
u-boot-nodtb 1113200 e4250 u-boot-nodtb 0
@atf-SEQ 0 0 section 0
atf-bl31 0 0 atf-bl31 0
@tee-SEQ 0 0 section 0
tee-os 0 0 tee-os 0
@fdt-SEQ 0 0 section 0
vbe-recovery 1800000 39b200 section 1800000
spl-recovery 1800000 100000 fit 0
spl 1801400 10c97 section 1400
section 1801400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
@fdt-SEQ 0 0 section 0
u-boot-recovery 1900000 29b200 fit 100000
spl 1902400 10c97 section 2400
section 1902400 10c97 section 0
u-boot-spl-nodtb 1a908 u-boot-spl-nodtb 0
u-boot-spl-bss-pad 1b0 u-boot-spl-bss-pad 1a908
u-boot 1913200 e4250 section 13200
u-boot-nodtb 1913200 e4250 u-boot-nodtb 0
@atf-SEQ 0 0 section 0
atf-bl31 0 0 atf-bl31 0
@tee-SEQ 0 0 section 0
tee-os 0 0 tee-os 0
@fdt-SEQ 0 0 section 0
fdtmap 1b9b200 2ecf fdtmap 1b9b200
Here is an example boot:
$ ub-int vbe
Building U-Boot in sourcedir for rk3399-generic-ddr3
Bootstrapping U-Boot from dir /tmp/b/rk3399-generic-ddr3
Writing U-Boot using method rockchip
U-Boot TPL 2026.07-rc3-00184-g311970460601 (May 28 2026 - 09:23:10)
Trying to boot from vbe_abrec
load: Firefly-RK3399 Board
## Loading firmware (any) from FIT Image at ff8ecb38 ...
Using 'config-7' configuration
Trying 'image-vpl' firmware subimage
## Loading fdt (any) from FIT Image at ff8ecb38 ...
Using 'config-7' configuration
Trying 'fdt-7' fdt subimage
U-Boot VPL 2026.07-rc3-00184-g311970460601 (May 28 2026 - 09:23:10)
Trying to boot from vbe_abrec
load: Firefly-RK3399 Board
Starting with empty state
VBE: Firmware pick A at 800000
## Loading firmware (SPL Phase) from FIT Image at ff8ec858 ...
Using 'config-7' configuration
Trying 'spl' firmware subimage
## Loading fdt (SPL Phase) from FIT Image at ff8ec858 ...
Using 'config-7' configuration
Trying 'fdt-7' fdt subimage
Channel 0: DDR3, 800MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: DDR3, 800MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
U-Boot SPL 2026.07-rc3-00184-g311970460601 (May 28 2026 - 09:23:10 -0600)
Trying to boot from vbe_abrec
load: Firefly-RK3399 Board
VBE: Firmware pick A at 900000
## Checking hash(es) for config config-7 ... OK
## Checking hash(es) for Image atf-1 ... sha256+ OK
## Checking hash(es) for Image u-boot ... sha256+ OK
## Checking hash(es) for Image fdt-7 ... sha256+ OK
## Checking hash(es) for Image fdt-7 ... sha256+ OK
## Checking hash(es) for Image atf-2 ... sha256+ OK
## Checking hash(es) for Image atf-3 ... sha256+ OK
## Checking hash(es) for Image atf-4 ... sha256+ OK
load_simple_fit: Skip load 'atf-5': image size is 0!
## Checking hash(es) for Image tee-1 ... sha256+ OK
ns16550_serial serial at ff1a0000: pinctrl_select_state_full: uclass_get_device_by_phandle_id: err=-19
U-Boot 2026.07-rc3-00184-g311970460601 (May 28 2026 - 09:23:10 -0600)
SoC: Rockchip rk3399
Reset cause: POR
Model: Firefly-RK3399 Board
DRAM: 4 GiB (total 3.9 GiB)
PMIC: RK808
Core: 307 devices, 32 uclasses, devicetree: separate
MMC: mmc at fe310000: 3, mmc at fe320000: 1, mmc at fe330000: 0
Loading Environment from MMC... Reading from MMC(0)... *** Warning - bad CRC, using default environment
In: serial,usbkbd
Out: serial,vidconsole
Err: serial,vidconsole
Model: Firefly-RK3399 Board
Net: eth0: ethernet at fe300000
Hit any key to stop autoboot: 0
Scanning for bootflows in all bootdevs
Seq Method State Uclass Part Name Filename
--- ----------- ------ -------- ---- ------------------------ ----------------
Scanning global bootmeth 'firmware0':
Scanning bootdev 'mmc at fe320000.bootdev':
Scanning bootdev 'mmc at fe330000.bootdev':
rockchip_pcie pcie at f8000000: PCIe link training gen1 timeout!
Unknown uclass 'scsi' in label
USB EHCI 1.00
USB EHCI 1.00
USB XHCI 1.10
Bus usb at fe380000: 1 USB Device(s) found
Bus usb at fe3c0000: 2 USB Device(s) found
Bus usb at fe900000: 1 USB Device(s) found
rockchip_pcie pcie at f8000000: PCIe link training gen1 timeout!
Scanning bootdev 'ethernet at fe300000.bootdev':
Scanning bootdev 'ethernet at fe300000.bootdev':
Scanning global bootmeth 'firmware0':
--- ----------- ------ -------- ---- ------------------------ ----------------
(0 bootflows, 0 valid)
=> vbe state
Phases: TPL (margin 91bb) VPL (margin 231e) SPL
This is (mostly) the final VBE series, but there are a few loose ends to
tidy up:
- pinctrl init needs to be tidied up to avoid warnings
- bloblist logic as mentioned above
Other things may become apparently after more usage / testing.
Changes in v8:
- Drop bloblist changes
- Update cover letter and add an example boot
Changes in v6:
- Update CONFIG_SPL_PAD_TO for puma-rk3399 and ringneck-px30
Changes in v5:
- Drop stray #endif
- Drop removal of stray #ifdef
- Mention VBE in the first paragraph of the commit message
- Wrap the entire simple-bin node and add the properties to vpl
- Expand commit message to mention VBE
- Move SUPPORT_VPL next to other SUPPORT_xxx options
- Put TPL_DM_MMC in alpha order
- Move VPL_ROCKCHIP_COMMON_BOARD up a bit
- Move VPL_LDSCRIPT up a bit
- Drop config SPL_STACK_R_ADDR
- Use if() instead of ? in spl_boot_device()
- Drop mention of SPL_RAW_IMAGE_SUPPORT since it is already the default
- Drop mention of SPL_SEPARATE_BSS since VPL doesn't need it
- Drop duplicate __image_copy_start and __image_copy_end
- Drop unwanted comment in script
- Reword first paragraph to mention bloblist instead of other stacks
- Add value for CONFIG_SPL_STACK_R_ADDR
- Add to VPL file also
Changes in v4:
- Use FIT_ARCH instead of ARCH
- Use FIT_ARCH instead of ARCH
- Use FIT_ARCH instead of ARCH
- Use fit_template instead of common_part
- Put the fdtmap at the end of the image
- Update the comment at the end of the '#ifndef CONFIG_VPL' block
- Add a value for SPL_STACK_R_ADDR
- Drop SPL_PAD_TO value since the default is fine
- Drop ROCKCHIP_IODOMAIN since it is the default
- Add SPL_LIBCOMMON_SUPPORT and SPL_LIBGENERIC_SUPPORT
Changes in v3:
- Add blank lines before the node
- Add a comment about the offsets
- Move template to the vpl file
- Unindent bootph tags
Changes in v2:
- Move VPL things into a separate file
- Move VPL things into a separate file
- Move VPL things into a separate file
- Mention RK3399 with respect to the memory limit
- Move VPL things into a separate file
- Only enable MMC when VPM is in use.
- Rewrite help for VPL_ROCKCHIP_COMMON_BOARD
- Skip spl-boot-order.c for VPL (rather than modifying it)
- Reword commit to mention comments from Jonas
- Rename to rk3399-generic-ddr3
- Update devicetree to match firefly-rk3399
- Use the firefly devicetree as the default for this board
- Move this patch to the end of the series
- Drop 0x8000 offset for SPI
- Add new patch with a bootmeth driver for abrec
- Split out the fixes for skip-at-start into a new patch
Simon Glass (22):
spl: Adjust xPL symbols
spl: Allow VBE to handle xPL size
vbe: Show the margin when using SPL_RELOC
rockchip: Allow RAM init to happen in SPL on rk3399
rockchip: dts: Add an fdtmap
rockchip: dts: Specify the phase in the image
rockchip: Provide a bootstd configuration
rockchip: Add SPL into the main FIT
rockchip: Add a template for SPL
rockchip: Add a VPL image
rockchip: Add TPL alternatives
rockchip: Update rk3399 bootph-tags for VPL
rockchip: Provide a VPL phase on rk3399
rockchip: Add symbols for spl_reloc
rockchip: rk3399: Adjust TPL stack to allow for bloblist
rockchip: Allow SPL to set up SDRAM
rockchip: Add a generic-ddr3 rk3399 board
rockchip: Add documentation for VBE
gitlab: Add an VBE board to the sjg lab
rockchip: Set the skip-at-start property correctly
vbe: Add a bootmeth driver for abrec
rockchip: Update binman image for new skip-at-start setup
.gitlab-ci.yml | 6 +
arch/arm/dts/rk3399-u-boot.dtsi | 9 +
arch/arm/dts/rockchip-u-boot.dtsi | 17 ++
arch/arm/dts/rockchip-vpl-u-boot.dtsi | 224 +++++++++++++++++++++++
arch/arm/include/asm/spl.h | 1 +
arch/arm/mach-rockchip/Kconfig | 23 ++-
arch/arm/mach-rockchip/Makefile | 11 +-
arch/arm/mach-rockchip/rk3399/Kconfig | 11 +-
arch/arm/mach-rockchip/spl.c | 3 +
arch/arm/mach-rockchip/tpl.c | 13 +-
arch/arm/mach-rockchip/u-boot-tpl-v8.lds | 10 +
arch/arm/mach-rockchip/u-boot-vpl-v8.lds | 107 +++++++++++
arch/arm/mach-rockchip/vpl.c | 53 ++++++
board/rockchip/evb_rk3399/MAINTAINERS | 6 +
boot/vbe_abrec.c | 99 ++++++++++
cmd/vbe.c | 8 +-
common/spl/Kconfig | 3 +-
common/spl/spl.c | 2 +
common/spl/spl_reloc.c | 14 +-
configs/puma-rk3399_defconfig | 2 +-
configs/ringneck-px30_defconfig | 2 +-
configs/rk3399-generic-ddr3_defconfig | 126 +++++++++++++
doc/board/rockchip/rockchip.rst | 13 ++
drivers/ram/rockchip/sdram_rk3399.c | 6 +-
include/vbe.h | 3 +
25 files changed, 753 insertions(+), 19 deletions(-)
create mode 100644 arch/arm/dts/rockchip-vpl-u-boot.dtsi
create mode 100644 arch/arm/mach-rockchip/u-boot-vpl-v8.lds
create mode 100644 arch/arm/mach-rockchip/vpl.c
create mode 100644 configs/rk3399-generic-ddr3_defconfig
---
base-commit: 746a986fe247fc0b3d52ad7ae7027e0a6d57d12c
branch: vbi-us7
--
2.43.0
More information about the U-Boot
mailing list