[U-Boot-Users] tftp server for Windows

[Scott McNutt]

Rune,

I have been using TFTPD32 without any problems in
a Windows 2000 environment:

http://tftpd32.jounin.net

Regards,
--Scott


> -----Original Message-----
> From:	Rune Raknerud [SMTP:rune.raknerud at cargoscan.com]
> Sent:	Monday, July 21, 2003 4:44 AM
> To:	U-Boot (E-mail)
> Cc:	Wolgang Denk (E-mail)
> Subject:	[U-Boot-Users] tftp server for Windows
> 
> Hi
> 
> I need to setup a tftp server on a Windows machine, and I tried to use
> tftpsrv that is provided by Abatron. This works fine with my BDI2000,
> but not with my custom MPC8245 board running u-boot. Both the BDI2000
> and the MPC8245 board work fine when connected to a tftp server on a
> RedHat 7.3 machine.
> 
> I use the following command for starting tftpsrv: tftpsrv w p
> dc:\tftpboot\
> 
> The following is a screen capture of the console output from the MPC8245
> board. 172.23.151.225 is a PC running  RedHat 7.3 and 172.23.151.232 is
> a PC running Windows 2000 Prof and tftpserv from Abatron. I have enabled
> debug output from u-boot.
> 
> =>setenv serverip 172.23.151.225
> =>tftp 100000 8245.cfg 
> ARP broadcast 1
> Receive from protocol 0x806
> Got ARP
> Got ARP REPLY, set server/gtwy eth addr
> Got good ARP - start TFTP
> 
> Server ethernet address 00:01:02:99:91:26
> TFTP from server 172.23.151.225; our IP address is 172.23.151.236
> Filename '8245.cfg'.
> Load address: 0x100000
> Loading: *Receive from protocol 0x800
> Got IP
> len=544, v=45
> #Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> #Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=544, v=45
> Receive from protocol 0x800
> Got IP
> len=347, v=45
> 
> done
> Bytes transferred = 7483 (1d3b hex)
> => reset 
> 
> U-Boot 0.2.0 (Jul 18 2003 - 09:10:38)
> 
> CPU:   MPC8245 Revision 1.2 at 299.999 MHz: 16 kB I-Cache 16 kB D-Cache
> Board: Cargoscan CS0045 CPU/RF PowerPC MPC8245 
> I2C:   ready
> DRAM:  64 MB
> Altera 1k10 ,,,,,,,,,,,,,,,,,,,
> Altera 1k50
> ........................................................................
> .........................
> FPGA:  ready on 1 atempt.
> FLASH:  8 MB
> In:    serial
> Out:   serial
> Err:   serial
> Net:   i82559#0, i82559#1
> IDE:   Bus 0: OK 
>   Device 0: Model: SanDisk SDCFB-64 Firm: vde 1.10
 Ser#: 20312131908
>             Type: Removable Hard Disk
>             Capacity: 61.2 MB = 0.0 GB (125440 x 512)
> => printenv baudrate=38400
> serial#=AO031245612346
> filesize=9fdf1
> sereverip=172.23.151.231
> serverip=172.23.151.232
> ipaddr=172.23.151.236
> bootargs=console=ttyS0,38400 root=/dev/nfs rw
> nfsroot=/home/filesystems/mvl30
> ip=172.23.151.233:172.23.151.232:172.23.151.40:255.255.255.0:io:eth0
> ide0=0xfe0001f0,0xfe0003f6,19
> stdin=serial
> stdout=serial
> stderr=serial
> 
> Environment size: 342/131068 bytes
> => tftp 100000 8245.cfg 
> ARP broadcast 1
> Receive from protocol 0x806
> Got ARP
> Got ARP REPLY, set server/gtwy eth addr
> Got good ARP - start TFTP
> 
> Server ethernet address 00:08:74:3b:61:58
> TFTP from server 172.23.151.232; our IP address is 172.23.151.236
> Filename '8245.cfg'.
> Load address: 0x100000
> Loading: *Receive from protocol 0x800
> Got IP
> len=56, v=45
> Receive from protocol 0x800
> Got IP
> len=128, v=45
> T Receive from protocol 0x800
> Got IP
> len=56, v=45
> Receive from protocol 0x806
> Got ARP
> T Receive from protocol 0x800
> Got IP
> len=56, v=45
> Receive from protocol 0x8137
> Receive from protocol 0x806
> Got ARP
> 
> Abort
> => 
> 
> From the u-boot output, it looks like the packet lengths is to short. 
> 
> Have any of you got the Abatron tftpsrv to work with u-boot. If yes, how
> did you do it? If no, do you know of any other tftp servers that run
> under Windows and work with u-boot?
> 
> Best regards
> Rune Raknerud
> Cargoscan AS
> 
> 
> -------------------------------------------------------
> This SF.net email is sponsored by: VM Ware
> With VMware you can run multiple operating systems on a single machine.
> WITHOUT REBOOTING! Mix Linux / Windows / Novell virtual machines at the
> same time. Free trial click here: http://www.vmware.com/wl/offer/345/0
> _______________________________________________
> U-Boot-Users mailing list
> U-Boot-Users at lists.sourceforge.net
> https://lists.sourceforge.net/lists/listinfo/u-boot-users
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.denx.de/pipermail/u-boot/attachments/20030721/67d8a3bb/attachment.htm