[U-Boot-Users] tftp server for Windows

[Rune Raknerud]

Hi

I need to setup a tftp server on a Windows machine, and I tried to use
tftpsrv that is provided by Abatron. This works fine with my BDI2000,
but not with my custom MPC8245 board running u-boot. Both the BDI2000
and the MPC8245 board work fine when connected to a tftp server on a
RedHat 7.3 machine.

I use the following command for starting tftpsrv: tftpsrv w p
dc:\tftpboot\

The following is a screen capture of the console output from the MPC8245
board. 172.23.151.225 is a PC running  RedHat 7.3 and 172.23.151.232 is
a PC running Windows 2000 Prof and tftpserv from Abatron. I have enabled
debug output from u-boot.

=>setenv serverip 172.23.151.225
=>tftp 100000 8245.cfg 
ARP broadcast 1
Receive from protocol 0x806
Got ARP
Got ARP REPLY, set server/gtwy eth addr
Got good ARP - start TFTP

Server ethernet address 00:01:02:99:91:26
TFTP from server 172.23.151.225; our IP address is 172.23.151.236
Filename '8245.cfg'.
Load address: 0x100000
Loading: *Receive from protocol 0x800
Got IP
len=544, v=45
#Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
#Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=544, v=45
Receive from protocol 0x800
Got IP
len=347, v=45

done
Bytes transferred = 7483 (1d3b hex)
=> reset 

U-Boot 0.2.0 (Jul 18 2003 - 09:10:38)

CPU:   MPC8245 Revision 1.2 at 299.999 MHz: 16 kB I-Cache 16 kB D-Cache
Board: Cargoscan CS0045 CPU/RF PowerPC MPC8245 
I2C:   ready
DRAM:  64 MB
Altera 1k10 ,,,,,,,,,,,,,,,,,,,
Altera 1k50
........................................................................
.........................
FPGA:  ready on 1 atempt.
FLASH:  8 MB
In:    serial
Out:   serial
Err:   serial
Net:   i82559#0, i82559#1
IDE:   Bus 0: OK 
  Device 0: Model: SanDisk SDCFB-64 Firm: vde 1.10
 Ser#: 20312131908
            Type: Removable Hard Disk
            Capacity: 61.2 MB = 0.0 GB (125440 x 512)
=> printenv baudrate=38400
serial#=AO031245612346
filesize=9fdf1
sereverip=172.23.151.231
serverip=172.23.151.232
ipaddr=172.23.151.236
bootargs=console=ttyS0,38400 root=/dev/nfs rw
nfsroot=/home/filesystems/mvl30
ip=172.23.151.233:172.23.151.232:172.23.151.40:255.255.255.0:io:eth0
ide0=0xfe0001f0,0xfe0003f6,19
stdin=serial
stdout=serial
stderr=serial

Environment size: 342/131068 bytes
=> tftp 100000 8245.cfg 
ARP broadcast 1
Receive from protocol 0x806
Got ARP
Got ARP REPLY, set server/gtwy eth addr
Got good ARP - start TFTP

Server ethernet address 00:08:74:3b:61:58
TFTP from server 172.23.151.232; our IP address is 172.23.151.236
Filename '8245.cfg'.
Load address: 0x100000
Loading: *Receive from protocol 0x800
Got IP
len=56, v=45
Receive from protocol 0x800
Got IP
len=128, v=45
T Receive from protocol 0x800
Got IP
len=56, v=45
Receive from protocol 0x806
Got ARP
T Receive from protocol 0x800
Got IP
len=56, v=45
Receive from protocol 0x8137
Receive from protocol 0x806
Got ARP

Abort
=>