[U-Boot-Users] [PATCH] Update board NetStar
Ladislav Michl
ladis at linux-mips.org
Thu Nov 3 13:07:37 CET 2005
Just to sync my local tree with public one. Generated against
testing-NAND branch.
Signed-off-by: Ladislav Michl <ladis at linux-mips.org>
CHANGELOG:
* Update board NetStar
Patch by Ladislav Michl, 3 Nov 2005
diff --git a/board/netstar/crcek.S b/board/netstar/crcek.S
--- a/board/netstar/crcek.S
+++ b/board/netstar/crcek.S
@@ -13,6 +13,7 @@
* u32 - crc32
*/
+#include <config.h>
#include "crcek.h"
/**
@@ -39,7 +40,7 @@
.macro crcuj, offset, size
mov r0, #0
ldr r1, \offset
- ldr r2, [r1]
+ ldr r2, [r1], #4
cmp r2, r0 @ no data, no problem
beq 2f
tst r2, #3 @ unaligned size
@@ -47,7 +48,6 @@
ldr r3, \size
cmp r2, r3 @ bogus size
bhi 2f
- add r1, r1, #4
do_crc32
ldr r1, [r1]
2:
@@ -55,16 +55,71 @@
.endm
.macro wait, reg
- mov \reg, #0x1000
+ mov \reg, #0x100000
3:
subs \reg, \reg, #0x1
bne 3b
-
.endm
+
.text
.globl crcek
crcek:
- b crc2_bad
+ /* Enable I-cache */
+ mrc p15, 0, r1, c0, c0, 0 @ read C15 ID register
+ mrc p15, 0, r1, c0, c0, 1 @ read C15 Cache information register
+ mrc p15, 0, r1, c1, c0, 0 @ read C15 Control register
+ orr r1, r1, #0x1000 @ enable I-cache, map interrupt vector 0xffff0000
+ mcr p15, 0, r1, c1, c0, 0 @ write C15 Control register
+ mov r1, #0x00
+ mcr p15, 0, r1, c7, c5, 0 @ Flush I-cache
+ nop
+ nop
+ nop
+ nop
+
+ /* Setup clocking mode */
+ ldr r0, MPU_CLKM_BASE @ base of CLOCK unit
+ ldrh r1, [r0, #0x18] @ ARM_SYST - get reset status
+ bic r1, r1, #(7 << 11) @ clear clock select
+ orr r1, r1, #(2 << 11) @ set synchronous scalable
+ mov r2, #0
+loop:
+ cmp r2, #1 @ this loop will wait for at least 100 cycles
+ streqh r1, [r0, #0x18] @ before issuing next request from MPU
+ add r2, r2, #1 @ on the 1st run code is loaded into I-cache
+ cmp r2, #16 @ and second run will set clocking mode
+ bne loop
+ nop
+
+ /* Setup clock dividers */
+ ldr r1, CKCTL_VAL
+ orr r1, r1, #0x2000 @ enable DSP clock
+ strh r1, [r0] @ setup clock divisors
+
+ /* Setup DPLL to generate requested freq */
+ ldr r0, DPLL1_BASE @ base of DPLL1 register
+ mov r1, #0x0010 @ set PLL_ENABLE
+ orr r1, r1, #0x2000 @ set IOB to new locking
+ orr r1, r1, #(OMAP5910_DPLL_MUL << 7) @ setup multiplier CLKREF
+ orr r1, r1, #(OMAP5910_DPLL_DIV << 5) @ setup divider CLKREF
+ strh r1, [r0] @ write
+
+locking:
+ ldrh r1, [r0] @ get DPLL value
+ tst r1, #0x01
+ beq locking @ while LOCK not set
+
+ /* Enable clock */
+ ldr r0, MPU_CLKM_BASE @ base of CLOCK unit
+ mov r1, #(1 << 10) @ disable idle mode do not check
+ @ nWAKEUP pin, other remain active
+ strh r1, [r0, #0x04]
+ ldr r1, EN_CLK_VAL
+ strh r1, [r0, #0x08]
+ mov r1, #0x003f @ FLASH.RP not enabled in idle and
+ strh r1, [r0, #0x0c] @ max delayed ( 32 x CLKIN )
+
+
mov r6, #0
crcuj _LOADER1_OFFSET, _LOADER_SIZE
bne crc1_bad
@@ -76,9 +131,8 @@ crc1_bad:
crc2_bad:
ldr r3, _LOADER1_OFFSET
ldr r4, _LOADER2_OFFSET
- b boot_2nd
- tst r6, #3
- beq one_is_bad @ one of them (or both) has bad crc
+ teq r6, #3
+ bne one_is_bad @ one of them (or both) has bad crc
ldr r1, [r3, #4]
ldr r2, [r4, #4]
cmp r1, r2 @ boot 2nd loader if versions differ
@@ -90,6 +144,7 @@ one_is_bad:
tst r6, #2
bne boot_2nd
@ We are doomed, so let user know.
+hell:
ldr r0, GPIO_BASE @ configure GPIO pins
ldr r1, GPIO_DIRECTION
strh r1, [r0, #0x08]
@@ -171,6 +226,15 @@ CRC32_TABLE:
GPIO_BASE:
.word 0xfffce000
+MPU_CLKM_BASE:
+ .word 0xfffece00
+DPLL1_BASE:
+ .word 0xfffecf00
+
+CKCTL_VAL:
+ .word OMAP5910_ARM_CKCTL
+EN_CLK_VAL:
+ .word OMAP5910_ARM_EN_CLK
GPIO_DIRECTION:
.word 0x0000ffe7
diff --git a/board/netstar/crcek.h b/board/netstar/crcek.h
diff --git a/board/netstar/crcit.c b/board/netstar/crcit.c
--- a/board/netstar/crcit.c
+++ b/board/netstar/crcit.c
@@ -77,7 +77,7 @@ int main(int argc, char **argv)
} else if ((argc == 4) && (strcmp(argv[1], "-v") == 0)) {
char *endptr, *nptr = argv[2];
unsigned ver = strtoul(nptr, &endptr, 0);
- if (nptr != '\0' && endptr == '\0')
+ if (*nptr != '\0' && *endptr == '\0')
return doit(argv[3], ver);
}
fprintf(stderr, "Usage: crcit [-v version] <image>\n");
diff --git a/board/netstar/eeprom.c b/board/netstar/eeprom.c
--- a/board/netstar/eeprom.c
+++ b/board/netstar/eeprom.c
@@ -213,3 +213,4 @@ int eeprom(int argc, char *argv[])
return 0;
}
+
diff --git a/board/netstar/nand.c b/board/netstar/nand.c
--- a/board/netstar/nand.c
+++ b/board/netstar/nand.c
@@ -55,10 +55,11 @@ static int netstar_nand_ready(struct mtd
void board_nand_init(struct nand_chip *nand)
{
- nand->options = NAND_SAMSUNG_LP_OPTIONS;
+ nand->options = NAND_SAMSUNG_LP_OPTIONS;
nand->eccmode = NAND_ECC_SOFT;
- nand->hwcontrol = netstar_nand_hwcontrol;
+ nand->hwcontrol = netstar_nand_hwcontrol;
/* nand->dev_ready = netstar_nand_ready; */
nand->chip_delay = 18;
}
#endif
+
diff --git a/board/netstar/netstar.c b/board/netstar/netstar.c
--- a/board/netstar/netstar.c
+++ b/board/netstar/netstar.c
@@ -27,7 +27,6 @@ int board_init(void)
DECLARE_GLOBAL_DATA_PTR;
/* arch number of NetStar board */
- /* TODO: use define from asm/mach-types.h */
gd->bd->bi_arch_number = 692;
/* adress of boot parameters */
@@ -53,16 +52,13 @@ int dram_init(void)
return 0;
}
-extern void partition_flash(void);
-
int misc_init_r(void)
{
return 0;
}
-extern void nand_init(void);
-
int board_late_init(void)
{
return 0;
}
+
diff --git a/board/netstar/setup.S b/board/netstar/setup.S
--- a/board/netstar/setup.S
+++ b/board/netstar/setup.S
@@ -58,10 +58,10 @@ VAL_EMIFF_SDRAM_CONFIG: .word ((0 << 0)
VAL_EMIFF_SDRAM_CONFIG: .word ((0 << 0) | (0 << 1) | (3 << 2) | (0xd << 4) | (0x246 << 8) | (0 << 24) | (0 << 26) | (0 << 27))
#endif
-VAL_EMIFF_SDRAM_CONFIG2: .word 0x00000003
+VAL_EMIFF_SDRAM_CONFIG2: .word 0x00000003
VAL_EMIFF_MRS: .word 0x00000037
-/*
+/*
* GPIO04 - Green LED (Red LED is connected to LED Pulse Generator)
* GPIO07 - LAN91C111 reset
*/
@@ -106,7 +106,7 @@ MUX_CONFIG_OFFSETS:
.align 1
.byte 0x00 @ FUNC_MUX_CTRL_0
.byte 0x04 @ FUNC_MUX_CTRL_1
- .byte 0x08 @ FUNC_MUX_CTRL_2
+ .byte 0x08 @ FUNC_MUX_CTRL_2
.byte 0x10 @ FUNC_MUX_CTRL_3
.byte 0x14 @ FUNC_MUX_CTRL_4
.byte 0x18 @ FUNC_MUX_CTRL_5
@@ -145,25 +145,23 @@ platformsetup:
nop
/* Setup clocking mode */
- ldr r0, OMAP5910_MPU_CLKM_BASE @ prepare base of CLOCK unit
- ldrh r1, [r0, #0x18] @ get reset status
+ ldr r0, OMAP5910_MPU_CLKM_BASE @ base of CLOCK unit
+ ldrh r1, [r0, #0x18] @ ARM_SYST - get reset status
bic r1, r1, #(7 << 11) @ clear clock select
orr r1, r1, #(2 << 11) @ set synchronous scalable
- mov r2, #0 @ set wait counter to 100 clock cycles
-
-icache_loop:
- cmp r2, #0x01
- streqh r1, [r0, #0x18]
- add r2, r2, #0x01
- cmp r2, #0x10
- bne icache_loop
+ mov r2, #0
+loop:
+ cmp r2, #1 @ this loop will wait for at least 100 cycles
+ streqh r1, [r0, #0x18] @ before issuing next request from MPU
+ add r2, r2, #1 @ on the 1st run code is loaded into I-cache
+ cmp r2, #16 @ and second run will set clocking mode
+ bne loop
nop
- /* Setup clock divisors */
- ldr r0, OMAP5910_MPU_CLKM_BASE @ base of CLOCK unit
+ /* Setup clock dividers */
ldr r1, _OMAP5910_ARM_CKCTL
orr r1, r1, #0x2000 @ enable DSP clock
- strh r1, [r0, #0x00] @ setup clock divisors
+ strh r1, [r0] @ setup clock divisors
/* Setup DPLL to generate requested freq */
ldr r0, OMAP5910_DPLL1_BASE @ base of DPLL1 register
@@ -182,18 +180,17 @@ locking:
ldr r0, OMAP5910_MPU_CLKM_BASE @ base of CLOCK unit
mov r1, #(1 << 10) @ disable idle mode do not check
@ nWAKEUP pin, other remain active
- strh r1, [r0, #0x04]
+ strh r1, [r0, #0x04]
ldr r1, _OMAP5910_ARM_EN_CLK
strh r1, [r0, #0x08]
mov r1, #0x003f @ FLASH.RP not enabled in idle and
- @ max delayed ( 32 x CLKIN )
- strh r1, [r0, #0x0c]
+ strh r1, [r0, #0x0c] @ max delayed ( 32 x CLKIN )
/* Configure 5910 pins functions to match our board. */
ldr r0, MUX_CONFIG_BASE
adr r1, MUX_CONFIG_VALUES
adr r2, MUX_CONFIG_OFFSETS
-next_mux_cfg:
+next_mux_cfg:
ldrb r3, [r2], #1
ldr r4, [r1], #4
cmp r3, #0xff
@@ -240,15 +237,15 @@ next_mux_cfg:
strh r1, [r0, #0x34]
/* Setup clock divisors */
- ldr r0, OMAP5910_ULPD_PWR_MNG_BASE @ base of ULDPL DPLL1 register
+ ldr r0, OMAP5910_ULPD_PWR_MNG_BASE @ base of ULDPL DPLL1 register
mov r1, #0x0010 @ set PLL_ENABLE
- orr r1, r1, #0x2000 @ set IOB to new locking
- strh r1, [r0] @ write
+ orr r1, r1, #0x2000 @ set IOB to new locking
+ strh r1, [r0] @ write
ulocking:
ldrh r1, [r0] @ get DPLL value
- tst r1, #1
+ tst r1, #1
beq ulocking @ while LOCK not set
/* EMIF init */
@@ -257,7 +254,7 @@ ulocking:
bic r1, r1, #0x0c @ pwr down disabled, flash WP
orr r1, r1, #0x01
str r1, [r0, #0x0c]
-
+
ldr r1, VAL_EMIFS_CS0_CONFIG
str r1, [r0, #0x10] @ EMIFS_CS0_CONFIG
ldr r1, VAL_EMIFS_CS1_CONFIG
More information about the U-Boot
mailing list