[U-Boot-Users] cpu_init_f - OR0/BRO PRELIM
Rahul Kulkarni
rahul.kulkarni at gmail.com
Mon Oct 23 23:24:21 CEST 2006
I am trying to port uboot on our own board running mpc8541E processor.
Have all the board specfic stuff created and compiled in, did face a
few issues early on, but right now it seem like it goes all the way
till board_init_f and hangs. Bactracking through the startup code I
see that my LBC register have not been initialized. I have the
following settings in my board.config file
#define CFG_BR0_PRELIM 0xFE001801
#define CFG_OR0_PRELIM 0xFE006F35
2 * 16MB interleaved flashes configured on CS0
CCSRBAR config:
#define CFG_CCSRBAR_DEFAULT 0xFF700000 /* CCSRBAR Default */
#define CFG_CCSRBAR 0xE0000000 /* relocated CCSRBAR */
#define CFG_IMMR CFG_CCSRBAR /* PQII uses CFG_IMMR */
It does go through cpu_init_f with no exections etc but If I set a
breakpoint or stop it at some later point and look at the OR0/BRO
registes I do not see the above values being set. I am not quite sure
how the CCSRBAR reloacation code in start.S seems to handle the
relocation
I do see that we go through this part in the the debugger.
#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
/* Special sequence needed to update CCSRBAR itself */
lis r4, CFG_CCSRBAR_DEFAULT at h
ori r4, r4, CFG_CCSRBAR_DEFAULT at l
lis r5, CFG_CCSRBAR at h
ori r5, r5, CFG_CCSRBAR at l
srwi r6,r5,12
stw r6, 0(r4)
isync
lis r5, 0xffff
ori r5,r5,0xf000
lwz r5, 0(r5)
isync
lis r3, CFG_CCSRBAR at h
lwz r5, CFG_CCSRBAR at l(r3)
isync
#endif
I was wondering if these two variables are being set properly
volatile immap_t *immap = (immap_t *)CFG_IMMR;
volatile ccsr_lbc_t *memctl = &immap->im_lbc;
since the statment below in cpu_init_f does not seem to take effect.
memctl->br0 = CFG_BR0_PRELIM;
memctl->or0 = CFG_OR0_PRELIM;
I'd really appreciate any replies or suggestions.
thanks much,
Rahul
TLB config below:
/*
* TLB0 and TLB1 Entries
*
* Out of reset, TLB1's Entry 0 maps the highest 4K for CCSRBAR.
* However, CCSRBAR is then relocated to CFG_CCSRBAR right after
* these TLB entries are established.
*
* MAS0: tlbsel, esel, nv
* MAS1: valid, iprot, tid, ts, tsize
* MAS2: epn, sharen, x0, x1, w, i, m, g, e
* MAS3: rpn, u0-u3, ux, sx, uw, sw, ur, sr
*/
#define entry_start \
mflr r1 ; \
bl 0f ;
#define entry_end \
0: mflr r0 ; \
mtlr r1 ; \
blr ;
.section .bootpg, "ax"
.globl tlb1_entry
tlb1_entry:
entry_start
/*
* Number of TLB0 and TLB1 entries in the following table
*/
.long 13
#if (CFG_CCSRBAR_DEFAULT != CFG_CCSRBAR)
/*
* TLB0 4K Non-cacheable, guarded
* 0xff700000 4K Initial CCSRBAR mapping
*
* This ends up at a TLB0 Index==0 entry, and must not collide
* with other TLB0 Entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR_DEFAULT), 0,0,0,0,0,1,0,1,0,1)
#else
#error("Update the number of table entries in tlb1_entry")
#endif
/*
* TLB0 16K Cacheable, non-guarded
* 0xd001_0000 16K Temporary Global data for initialization
*
* Use four 4K TLB0 entries. These entries must be cacheable
* as they provide the bootstrap memory before the memory
* controler and real memory have been configured.
*
* These entries end up at TLB0 Indicies 0x10, 0x14, 0x18 and 0x1c,
* and must not collide with other TLB0 entries.
*/
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 4 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 4 * 1024),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 8 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 8 * 1024),
0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(0, 0, 0)
.long TLB1_MAS1(1, 0, 0, 0, 0)
.long TLB1_MAS2(E500_TLB_EPN(CFG_INIT_RAM_ADDR + 12 * 1024),
0,0,0,0,0,0,0,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_INIT_RAM_ADDR + 12 * 1024),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 0, 1: 32M Non-cacheable, guarded
* 0xfe000000 32FLASH
* Out of reset this entry is only 4K.
*/
.long TLB1_MAS0(1, 2, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE), 0,0,0,0,0,1,0,1,0,1)
.long TLB1_MAS0(1, 1, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_16M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_FLASH_BASE+0x1000000), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 3: 256M Non-cacheable, guarded
* 0x80000000 256M PCI1 MEM First half
*/
.long TLB1_MAS0(1, 3, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 4: 256M Non-cacheable, guarded
* 0x90000000 256M PCI1 MEM Second half
*/
.long TLB1_MAS0(1, 4, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_PCI1_MEM_BASE + 0x10000000),
0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_PCI1_MEM_BASE + 0x10000000),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 5: 256M Non-cacheable, guarded
* 0xc0000000 256M Rapid IO MEM First half
*/
.long TLB1_MAS0(1, 5, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 6: 256M Non-cacheable, guarded
* 0xd0000000 256M Rapid IO MEM Second half
*/
.long TLB1_MAS0(1, 6, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_RIO_MEM_BASE + 0x10000000),
0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_RIO_MEM_BASE + 0x10000000),
0,0,0,0,0,1,0,1,0,1)
/*
* TLB 7: 64M Non-cacheable, guarded
* 0xe000_0000 1M CCSRBAR
* 0xe200_0000 16M PCI1 IO
*/
.long TLB1_MAS0(1, 7, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_64M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_CCSRBAR), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_CCSRBAR), 0,0,0,0,0,1,0,1,0,1)
/*
* TLB 8: 256M DDR, cache disabled (needed for memory test)
* 0x00000000 256M DDR System memory
* Without SPD EEPROM configured DDR, this must be setup manually.
* Make sure the TLB count at the top of this table is correct.
* Likely it needs to be increased by two for these entries.
*/
.long TLB1_MAS0(1, 8, 0)
.long TLB1_MAS1(1, 1, 0, 0, BOOKE_PAGESZ_256M)
.long TLB1_MAS2(E500_TLB_EPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,1,0,1,0)
.long TLB1_MAS3(E500_TLB_RPN(CFG_DDR_SDRAM_BASE), 0,0,0,0,0,1,0,1,0,1)
entry_end
/*
* LAW(Local Access Window) configuration:
*
* 0x0000_0000 0x7fff_ffff DDR 2G
* 0xe000_0000 0xe000_ffff CCSR 1M
* 0xfe00_0000 0xffff_ffff FLASH (boot bank) 32M
*
* Notes:
* CCSRBAR and L2-as-SRAM don't need a configured Local Access Window.
* If flash is 8M at default position (last 8M), no LAW needed.
*/
#define LAWBAR0 ((CFG_DDR_SDRAM_BASE>>12) & 0xfffff)
#define LAWAR0 (LAWAR_EN | LAWAR_TRGT_IF_DDR | (LAWAR_SIZE & LAWAR_SIZE_256M))
#define LAWBAR1 ((CFG_PCI1_MEM_BASE>>12) & 0xfffff)
#define LAWAR1 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_512M))
#define LAWBAR2 ((CFG_LBC_FLASH_BASE>>12) & 0xfffff)
#define LAWAR2 (LAWAR_EN | LAWAR_TRGT_IF_LBC | (LAWAR_SIZE & LAWAR_SIZE_32M))
#define LAWBAR3 ((CFG_PCI1_IO_BASE>>12) & 0xfffff)
#define LAWAR3 (LAWAR_EN | LAWAR_TRGT_IF_PCIX | (LAWAR_SIZE & LAWAR_SIZE_16M))
/*
* Rapid IO at 0xc000_0000 for 512 M
*/
#define LAWBAR4 ((CFG_RIO_MEM_BASE>>12) & 0xfffff)
#define LAWAR4 (LAWAR_EN | LAWAR_TRGT_IF_RIO | (LAWAR_SIZE & LAWAR_SIZE_512M))
.section .bootpg, "ax"
.globl law_entry
law_entry:
entry_start
.long 0x05
.long LAWBAR0,LAWAR0,LAWBAR1,LAWAR1,LAWBAR2,LAWAR2,LAWBAR3,LAWAR3
.long LAWBAR4,LAWAR4
entry_end
More information about the U-Boot
mailing list