[U-Boot-Users] [PATCH 1/4] emac
Michal Simek
monstr at seznam.cz
Sun Aug 5 20:56:25 CEST 2007
Hi Grant and everybody,
my patches are below. All patches are in u-boot-microblaze branch.
Signed-off-by: Michal Simek <monstr at monstr.eu>
Emac driver for Microblaze.
Michal Simek
diff --git a/Makefile b/Makefile
index bfa3846..146f647 100644
--- a/Makefile
+++ b/Makefile
@@ -143,7 +143,7 @@ ifeq ($(ARCH),m68k)
CROSS_COMPILE = m68k-elf-
endif
ifeq ($(ARCH),microblaze)
-CROSS_COMPILE = mb-
+CROSS_COMPILE = microblaze-uclinux-
endif
ifeq ($(ARCH),blackfin)
CROSS_COMPILE = bfin-uclinux-
@@ -199,7 +199,7 @@ LIBS += cpu/ixp/npe/libnpe.a
endif
LIBS += lib_$(ARCH)/lib$(ARCH).a
LIBS += fs/cramfs/libcramfs.a fs/fat/libfat.a fs/fdos/libfdos.a
fs/jffs2/libjffs2.a \
- fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a
+ fs/reiserfs/libreiserfs.a fs/ext2/libext2fs.a fs/romfs/libromfs.a
LIBS += net/libnet.a
LIBS += disk/libdisk.a
LIBS += rtc/librtc.a
@@ -207,6 +207,7 @@ LIBS += dtt/libdtt.a
LIBS += drivers/libdrivers.a
LIBS += drivers/nand/libnand.a
LIBS += drivers/nand_legacy/libnand_legacy.a
+LIBS += drivers/net/libnetdrv.a
ifeq ($(CPU),mpc83xx)
LIBS += drivers/qe/qe.a
endif
@@ -316,14 +317,14 @@ depend dep:
tags ctags:
ctags -w -o $(OBJTREE)/ctags `find $(SUBDIRS) include \
lib_generic board/$(BOARDDIR) cpu/$(CPU) lib_$(ARCH) \
- fs/cramfs fs/fat fs/fdos fs/jffs2 \
+ fs/cramfs fs/fat fs/fdos fs/jffs2 fs/romfs\
net disk rtc dtt drivers drivers/sk98lin common \
\( -name CVS -prune \) -o \( -name '*.[ch]' -print \)`
etags:
etags -a -o $(OBJTREE)/etags `find $(SUBDIRS) include \
lib_generic board/$(BOARDDIR) cpu/$(CPU) lib_$(ARCH) \
- fs/cramfs fs/fat fs/fdos fs/jffs2 \
+ fs/cramfs fs/fat fs/fdos fs/jffs2 fs/romfs\
net disk rtc dtt drivers drivers/sk98lin common \
\( -name CVS -prune \) -o \( -name '*.[ch]' -print \)`
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index e69de29..7342dc8 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -0,0 +1,45 @@
+#
+# (C) Copyright 2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB := $(obj)libnetdrv.a
+
+COBJS := xilinx_emaclite.o xilinx_emac.o
+
+SRCS := $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+
+all: $(LIB)
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/drivers/net/xilinx_emac.c b/drivers/net/xilinx_emac.c
index e69de29..d44f31e 100644
--- a/drivers/net/xilinx_emac.c
+++ b/drivers/net/xilinx_emac.c
@@ -0,0 +1,372 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr at monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Based on Xilinx drivers
+ *
+ */
+
+#include <config.h>
+#include <common.h>
+#include <net.h>
+#include <asm/io.h>
+#include <asm/asm.h>
+#include "xilinx_emac.h"
+
+#ifdef XILINX_EMAC
+
+#undef DEBUG
+
+#define ENET_MAX_MTU PKTSIZE
+#define ENET_ADDR_LENGTH 6
+
+static unsigned int etherrxbuff[PKTSIZE_ALIGN/4]; /* Receive buffer */
+
+static u8 EMACAddr[ENET_ADDR_LENGTH] = { 0x00, 0x0a, 0x35, 0x00, 0x22,
0x01 };
+
+static XEmac Emac;
+
+void eth_halt(void)
+{
+ return;
+}
+
+int eth_init(bd_t * bis)
+{
+ u32 HelpReg;
+#ifdef DEBUG
+ printf("EMAC Initialization Started\n\r");
+#endif
+ if (Emac.IsStarted) {
+ puts("Emac is started\n");
+ return 0;
+ }
+
+ memset (&Emac, 0, sizeof (XEmac));
+
+ Emac.BaseAddress = XILINX_EMAC_BASEADDR;
+
+ /* Setting up FIFOs */
+ Emac.RecvFifo.RegBaseAddress = Emac.BaseAddress +
+ XEM_PFIFO_RXREG_OFFSET;
+ Emac.RecvFifo.DataBaseAddress = Emac.BaseAddress +
+ XEM_PFIFO_RXDATA_OFFSET;
+ out_be32 (Emac.RecvFifo.RegBaseAddress, XPF_RESET_FIFO_MASK);
+
+ Emac.SendFifo.RegBaseAddress = Emac.BaseAddress +
+ XEM_PFIFO_TXREG_OFFSET;
+ Emac.SendFifo.DataBaseAddress = Emac.BaseAddress +
+ XEM_PFIFO_TXDATA_OFFSET;
+ out_be32 (Emac.SendFifo.RegBaseAddress, XPF_RESET_FIFO_MASK);
+
+ /* Reset the entire IPIF */
+ out_be32 (Emac.BaseAddress + XIIF_V123B_RESETR_OFFSET,
+ XIIF_V123B_RESET_MASK);
+
+ /* Stopping EMAC for setting up MAC */
+ HelpReg = in_be32 (Emac.BaseAddress + XEM_ECR_OFFSET);
+ HelpReg &= ~(XEM_ECR_XMIT_ENABLE_MASK | XEM_ECR_RECV_ENABLE_MASK);
+ out_be32 (Emac.BaseAddress + XEM_ECR_OFFSET, HelpReg);
+
+ if (!getenv("ethaddr")) {
+ memcpy(bis->bi_enetaddr, EMACAddr, ENET_ADDR_LENGTH);
+ }
+
+ /* Set the device station address high and low registers */
+ HelpReg = (bis->bi_enetaddr[0] << 8) | bis->bi_enetaddr[1];
+ out_be32 (Emac.BaseAddress + XEM_SAH_OFFSET, HelpReg);
+ HelpReg = (bis->bi_enetaddr[2] << 24) | (bis->bi_enetaddr[3] << 16) |
+ (bis->bi_enetaddr[4] << 8) | bis->bi_enetaddr[5];
+ out_be32 (Emac.BaseAddress + XEM_SAL_OFFSET, HelpReg);
+
+
+ HelpReg = XEM_ECR_UNICAST_ENABLE_MASK | XEM_ECR_BROAD_ENABLE_MASK |
+ XEM_ECR_FULL_DUPLEX_MASK | XEM_ECR_XMIT_FCS_ENABLE_MASK |
+ XEM_ECR_XMIT_PAD_ENABLE_MASK | XEM_ECR_PHY_ENABLE_MASK;
+ out_be32 (Emac.BaseAddress + XEM_ECR_OFFSET, HelpReg);
+
+ Emac.IsStarted = 1;
+
+ /* Enable the transmitter, and receiver */
+ HelpReg = in_be32 (Emac.BaseAddress + XEM_ECR_OFFSET);
+ HelpReg &= ~(XEM_ECR_XMIT_RESET_MASK | XEM_ECR_RECV_RESET_MASK);
+ HelpReg |= (XEM_ECR_XMIT_ENABLE_MASK | XEM_ECR_RECV_ENABLE_MASK);
+ out_be32 (Emac.BaseAddress + XEM_ECR_OFFSET, HelpReg);
+
+ printf("EMAC Initialization complete\n\r");
+ return 0;
+}
+
+int eth_send(volatile void *ptr, int len)
+{
+ u32 IntrStatus;
+ u32 XmitStatus;
+ u32 FifoCount;
+ u32 WordCount;
+ u32 ExtraByteCount;
+ u32 *WordBuffer = (u32 *) ptr;
+
+ if (len > ENET_MAX_MTU)
+ len = ENET_MAX_MTU;
+
+ /*
+ * Check for overruns and underruns for the transmit status and length
+ * FIFOs and make sure the send packet FIFO is not deadlocked.
+ * Any of these conditions is bad enough that we do not want to
+ * continue. The upper layer software should reset the device to resolve
+ * the error.
+ */
+ IntrStatus = in_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET);
+ if (IntrStatus & (XEM_EIR_XMIT_SFIFO_OVER_MASK |
+ XEM_EIR_XMIT_LFIFO_OVER_MASK)) {
+#ifdef DEBUG
+ puts ("Transmitting overrun error\n");
+#endif
+ return 0;
+ } else if (IntrStatus & (XEM_EIR_XMIT_SFIFO_UNDER_MASK |
+ XEM_EIR_XMIT_LFIFO_UNDER_MASK)) {
+#ifdef DEBUG
+ puts ("Transmitting underrun error\n");
+#endif
+ return 0;
+ } else if (in_be32 (Emac.SendFifo.RegBaseAddress +
+ XPF_COUNT_STATUS_REG_OFFSET) & XPF_DEADLOCK_MASK) {
+#ifdef DEBUG
+ puts("Transmitting fifo error\n");
+#endif
+ return 0;
+ }
+
+ /*
+ * Before writing to the data FIFO, make sure the length FIFO is not
+ * full. The data FIFO might not be full yet even though the length FIFO
+ * is. This avoids an overrun condition on the length FIFO and keeps the
+ * FIFOs in sync.
+ *
+ * Clear the latched LFIFO_FULL bit so next time around the most
+ * current status is represented
+ */
+ if (IntrStatus & XEM_EIR_XMIT_LFIFO_FULL_MASK) {
+ out_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET, IntrStatus
+ & XEM_EIR_XMIT_LFIFO_FULL_MASK);
+#ifdef DEBUG
+ puts ("Fifo is full\n");
+#endif
+ return 0;
+ }
+
+ /* get the count of how many words may be inserted into the FIFO */
+ FifoCount = in_be32 (Emac.SendFifo.RegBaseAddress +
+ XPF_COUNT_STATUS_REG_OFFSET) & XPF_COUNT_MASK;
+ WordCount = len >> 2;
+ ExtraByteCount = len & 0x3;
+
+ if (FifoCount < WordCount) {
+#ifdef DEBUG
+ puts ("Sending packet is larger then size of FIFO\n");
+#endif
+ return 0;
+ }
+
+ for (FifoCount = 0; FifoCount < WordCount; FifoCount++) {
+ out_be32 (Emac.SendFifo.DataBaseAddress, WordBuffer[FifoCount]);
+ }
+ if (ExtraByteCount > 0) {
+ u32 LastWord = 0;
+ u8 *ExtraBytesBuffer = (u8 *) (WordBuffer + WordCount);
+
+ if (ExtraByteCount == 1) {
+ LastWord = ExtraBytesBuffer[0] << 24;
+ } else if (ExtraByteCount == 2) {
+ LastWord = ExtraBytesBuffer[0] << 24 |
+ ExtraBytesBuffer[1] << 16;
+ } else if (ExtraByteCount == 3) {
+ LastWord = ExtraBytesBuffer[0] << 24 |
+ ExtraBytesBuffer[1] << 16 |
+ ExtraBytesBuffer[2] << 8;
+ }
+ out_be32 (Emac.SendFifo.DataBaseAddress, LastWord);
+ }
+
+ /* Loop on the MAC's status to wait for any pause to complete */
+ IntrStatus = in_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET);
+ while ((IntrStatus & XEM_EIR_XMIT_PAUSE_MASK) != 0) {
+ IntrStatus = in_be32 ((Emac.BaseAddress) +
+ XIIF_V123B_IISR_OFFSET);
+ /* Clear the pause status from the transmit status register */
+ out_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET,
+ IntrStatus & XEM_EIR_XMIT_PAUSE_MASK);
+ }
+
+ /*
+ * Set the MAC's transmit packet length register to tell it to transmit
+ */
+ out_be32 (Emac.BaseAddress + XEM_TPLR_OFFSET, len);
+
+ /*
+ * Loop on the MAC's status to wait for the transmit to complete.
+ * The transmit status is in the FIFO when the XMIT_DONE bit is set.
+ */
+ do {
+ IntrStatus = in_be32 ((Emac.BaseAddress) +
+ XIIF_V123B_IISR_OFFSET);
+ }
+ while ((IntrStatus & XEM_EIR_XMIT_DONE_MASK) == 0);
+
+ XmitStatus = in_be32 (Emac.BaseAddress + XEM_TSR_OFFSET);
+
+ if (IntrStatus & (XEM_EIR_XMIT_SFIFO_OVER_MASK |
+ XEM_EIR_XMIT_LFIFO_OVER_MASK)) {
+#ifdef DEBUG
+ puts ("Transmitting overrun error\n");
+#endif
+ return 0;
+ } else if (IntrStatus & (XEM_EIR_XMIT_SFIFO_UNDER_MASK |
+ XEM_EIR_XMIT_LFIFO_UNDER_MASK)) {
+#ifdef DEBUG
+ puts ("Transmitting underrun error\n");
+#endif
+ return 0;
+ }
+
+ /* Clear the interrupt status register of transmit statuses */
+ out_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET,
+ IntrStatus & XEM_EIR_XMIT_ALL_MASK);
+
+ /*
+ * Collision errors are stored in the transmit status register
+ * instead of the interrupt status register
+ */
+ if ((XmitStatus & XEM_TSR_EXCESS_DEFERRAL_MASK) ||
+ (XmitStatus & XEM_TSR_LATE_COLLISION_MASK)) {
+#ifdef DEBUG
+ puts ("Transmitting collision error\n");
+#endif
+ return 0;
+ }
+ return 1;
+}
+
+int eth_rx(void)
+{
+ u32 PktLength;
+ u32 IntrStatus;
+ u32 FifoCount;
+ u32 WordCount;
+ u32 ExtraByteCount;
+ u32 LastWord;
+ u8 *ExtraBytesBuffer;
+
+ if (in_be32 (Emac.RecvFifo.RegBaseAddress + XPF_COUNT_STATUS_REG_OFFSET)
+ & XPF_DEADLOCK_MASK) {
+ out_be32 (Emac.RecvFifo.RegBaseAddress, XPF_RESET_FIFO_MASK);
+#ifdef DEBUG
+ puts ("Receiving FIFO deadlock\n");
+#endif
+ return 0;
+ }
+
+ /*
+ * Get the interrupt status to know what happened (whether an error
occurred
+ * and/or whether frames have been received successfully). When clearing
the
+ * intr status register, clear only statuses that pertain to receive.
+ */
+ IntrStatus = in_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET);
+ /*
+ * Before reading from the length FIFO, make sure the length FIFO is not
+ * empty. We could cause an underrun error if we try to read from an
+ * empty FIFO.
+ */
+ if (!(IntrStatus & XEM_EIR_RECV_DONE_MASK)) {
+#ifdef DEBUG
+ /* puts("Receiving FIFO is empty\n"); */
+#endif
+ return 0;
+ }
+
+ /*
+ * Determine, from the MAC, the length of the next packet available
+ * in the data FIFO (there should be a non-zero length here)
+ */
+ PktLength = in_be32 (Emac.BaseAddress + XEM_RPLR_OFFSET);
+ if (!PktLength) {
+ return 0;
+ }
+
+ /*
+ * Write the RECV_DONE bit in the status register to clear it. This bit
+ * indicates the RPLR is non-empty, and we know it's set at this point.
+ * We clear it so that subsequent entry into this routine will reflect
+ * the current status. This is done because the non-empty bit is latched
+ * in the IPIF, which means it may indicate a non-empty condition even
+ * though there is something in the FIFO.
+ */
+ out_be32 ((Emac.BaseAddress) + XIIF_V123B_IISR_OFFSET,
+ XEM_EIR_RECV_DONE_MASK);
+
+ FifoCount = in_be32 (Emac.RecvFifo.RegBaseAddress +
+ XPF_COUNT_STATUS_REG_OFFSET) & XPF_COUNT_MASK;
+
+ if ((FifoCount * 4) < PktLength) {
+#ifdef DEBUG
+ puts ("Receiving FIFO is smaller than packet size.\n");
+#endif
+ return 0;
+ }
+
+ WordCount = PktLength >> 2;
+ ExtraByteCount = PktLength & 0x3;
+
+ for (FifoCount = 0; FifoCount < WordCount; FifoCount++) {
+ etherrxbuff[FifoCount] =
+ in_be32 (Emac.RecvFifo.DataBaseAddress);
+ }
+
+ /*
+ * if there are extra bytes to handle, read the last word from the FIFO
+ * and insert the extra bytes into the buffer
+ */
+ if (ExtraByteCount > 0) {
+ ExtraBytesBuffer = (u8 *) (etherrxbuff + WordCount);
+
+ LastWord = in_be32 (Emac.RecvFifo.DataBaseAddress);
+
+ /*
+ * one extra byte in the last word, put the byte into the next
+ * location of the buffer, bytes in a word of the FIFO are
+ * ordered from most significant byte to least
+ */
+ if (ExtraByteCount == 1) {
+ ExtraBytesBuffer[0] = (u8) (LastWord >> 24);
+ } else if (ExtraByteCount == 2) {
+ ExtraBytesBuffer[0] = (u8) (LastWord >> 24);
+ ExtraBytesBuffer[1] = (u8) (LastWord >> 16);
+ } else if (ExtraByteCount == 3) {
+ ExtraBytesBuffer[0] = (u8) (LastWord >> 24);
+ ExtraBytesBuffer[1] = (u8) (LastWord >> 16);
+ ExtraBytesBuffer[2] = (u8) (LastWord >> 8);
+ }
+ }
+ NetReceive((uchar *)etherrxbuff, PktLength);
+ return 1;
+}
+#endif
diff --git a/drivers/net/xilinx_emac.h b/drivers/net/xilinx_emac.h
index e69de29..7c00eeb 100644
--- a/drivers/net/xilinx_emac.h
+++ b/drivers/net/xilinx_emac.h
@@ -0,0 +1,127 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr at monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ *
+ * Based on Xilinx drivers
+ *
+ */
+
+typedef struct {
+ u32 RegBaseAddress; /* Base address of registers */
+ u32 DataBaseAddress; /* Base address of data for FIFOs */
+} XPacketFifoV100b;
+
+typedef struct {
+ u32 BaseAddress; /* Base address (of IPIF) */
+ u32 IsStarted; /* Device is currently started 0-no, 1-yes */
+ XPacketFifoV100b RecvFifo; /* FIFO used to receive frames */
+ XPacketFifoV100b SendFifo; /* FIFO used to send frames */
+} XEmac;
+
+#define XIIF_V123B_IISR_OFFSET 32UL /* IP interrupt status register */
+#define XIIF_V123B_RESET_MASK 0xAUL
+#define XIIF_V123B_RESETR_OFFSET 64UL /* reset register */
+
+/* This constant is used with the Reset Register */
+#define XPF_RESET_FIFO_MASK 0x0000000A
+#define XPF_COUNT_STATUS_REG_OFFSET 4UL
+
+/* These constants are used with the Occupancy/Vacancy Count Register. This
+ * register also contains FIFO status */
+#define XPF_COUNT_MASK 0x0000FFFF
+#define XPF_DEADLOCK_MASK 0x20000000
+
+/* Offset of the MAC registers from the IPIF base address */
+#define XEM_REG_OFFSET 0x1100UL
+
+/*
+ * Register offsets for the Ethernet MAC. Each register is 32 bits.
+ */
+#define XEM_ECR_OFFSET (XEM_REG_OFFSET + 0x4) /* MAC Control */
+#define XEM_SAH_OFFSET (XEM_REG_OFFSET + 0xC) /* Station addr, high */
+#define XEM_SAL_OFFSET (XEM_REG_OFFSET + 0x10) /* Station addr, low */
+#define XEM_RPLR_OFFSET (XEM_REG_OFFSET + 0x1C) /* Rx packet length */
+#define XEM_TPLR_OFFSET (XEM_REG_OFFSET + 0x20) /* Tx packet length */
+#define XEM_TSR_OFFSET (XEM_REG_OFFSET + 0x24) /* Tx status */
+
+
+
+#define XEM_PFIFO_OFFSET 0x2000UL
+#define XEM_PFIFO_TXREG_OFFSET (XEM_PFIFO_OFFSET + 0x0) /* Tx registers */
+#define XEM_PFIFO_RXREG_OFFSET (XEM_PFIFO_OFFSET + 0x10) /* Rx registers */
+#define XEM_PFIFO_TXDATA_OFFSET (XEM_PFIFO_OFFSET + 0x100) /* Tx keyhole */
+#define XEM_PFIFO_RXDATA_OFFSET (XEM_PFIFO_OFFSET + 0x200) /* Rx keyhole */
+
+
+/*
+ * EMAC Interrupt Registers (Status and Enable) masks. These registers are
+ * part of the IPIF IP Interrupt registers
+ */
+/* A mask for all transmit interrupts, used in polled mode */
+#define XEM_EIR_XMIT_ALL_MASK (XEM_EIR_XMIT_DONE_MASK |\
+ XEM_EIR_XMIT_ERROR_MASK | \
+ XEM_EIR_XMIT_SFIFO_EMPTY_MASK |\
+ XEM_EIR_XMIT_LFIFO_FULL_MASK)
+
+#define XEM_EIR_XMIT_DONE_MASK 0x00000001UL /* Xmit complete */
+#define XEM_EIR_RECV_DONE_MASK 0x00000002UL /* Recv complete */
+#define XEM_EIR_XMIT_ERROR_MASK 0x00000004UL /* Xmit error */
+#define XEM_EIR_RECV_ERROR_MASK 0x00000008UL /* Recv error */
+#define XEM_EIR_XMIT_SFIFO_EMPTY_MASK 0x00000010UL /* Xmit status fifo
empty */
+#define XEM_EIR_RECV_LFIFO_EMPTY_MASK 0x00000020UL /* Recv length fifo
empty */
+#define XEM_EIR_XMIT_LFIFO_FULL_MASK 0x00000040UL /* Xmit length fifo full
*/
+#define XEM_EIR_RECV_LFIFO_OVER_MASK 0x00000080UL /* Recv length fifo
+ * overrun */
+#define XEM_EIR_RECV_LFIFO_UNDER_MASK 0x00000100UL /* Recv length fifo
+ * underrun */
+#define XEM_EIR_XMIT_SFIFO_OVER_MASK 0x00000200UL /* Xmit status fifo
+ * overrun */
+#define XEM_EIR_XMIT_SFIFO_UNDER_MASK 0x00000400UL /* Transmit status fifo
+ * underrun */
+#define XEM_EIR_XMIT_LFIFO_OVER_MASK 0x00000800UL /* Transmit length fifo
+ * overrun */
+#define XEM_EIR_XMIT_LFIFO_UNDER_MASK 0x00001000UL /* Transmit length fifo
+ * underrun */
+#define XEM_EIR_XMIT_PAUSE_MASK 0x00002000UL /* Transmit pause pkt
+ * received */
+
+/*
+ * EMAC Control Register (ECR)
+ */
+#define XEM_ECR_FULL_DUPLEX_MASK 0x80000000UL /* Full duplex mode */
+#define XEM_ECR_XMIT_RESET_MASK 0x40000000UL /* Reset transmitter */
+#define XEM_ECR_XMIT_ENABLE_MASK 0x20000000UL /* Enable transmitter */
+#define XEM_ECR_RECV_RESET_MASK 0x10000000UL /* Reset receiver */
+#define XEM_ECR_RECV_ENABLE_MASK 0x08000000UL /* Enable receiver */
+#define XEM_ECR_PHY_ENABLE_MASK 0x04000000UL /* Enable PHY */
+#define XEM_ECR_XMIT_PAD_ENABLE_MASK 0x02000000UL /* Enable xmit pad
+ * insert */
+#define XEM_ECR_XMIT_FCS_ENABLE_MASK 0x01000000UL /* Enable xmit FCS
+ * insert */
+#define XEM_ECR_UNICAST_ENABLE_MASK 0x00020000UL /* Enable unicast
+ * addr */
+#define XEM_ECR_BROAD_ENABLE_MASK 0x00008000UL /* Enable broadcast
+ * addr */
+
+/* Transmit Status Register (TSR) */
+#define XEM_TSR_EXCESS_DEFERRAL_MASK 0x80000000UL /* Transmit excess
deferral */
+#define XEM_TSR_LATE_COLLISION_MASK 0x01000000UL /* Transmit late collision
*/
diff --git a/drivers/net/xilinx_emaclite.c b/drivers/net/xilinx_emaclite.c
index e69de29..99e7035 100644
--- a/drivers/net/xilinx_emaclite.c
+++ b/drivers/net/xilinx_emaclite.c
@@ -0,0 +1,378 @@
+/*
+ * (C) Copyright 2007 Michal Simek
+ *
+ * Michal SIMEK <monstr at monstr.eu>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <net.h>
+#include <config.h>
+#include <asm/io.h>
+
+#ifdef XILINX_EMACLITE_BASEADDR
+
+#undef DEBUG
+
+#define ENET_MAX_MTU PKTSIZE
+#define ENET_MAX_MTU_ALIGNED PKTSIZE_ALIGN
+#define ENET_ADDR_LENGTH 6
+
+/* EmacLite constants */
+#define XEL_BUFFER_OFFSET 0x0800 /* Next buffer's offset */
+#define XEL_TPLR_OFFSET 0x07F4 /* Tx packet length */
+#define XEL_TSR_OFFSET 0x07FC /* Tx status */
+#define XEL_RSR_OFFSET 0x17FC /* Rx status */
+#define XEL_RXBUFF_OFFSET 0x1000 /* Receive Buffer */
+
+/* Xmit complete */
+#define XEL_TSR_XMIT_BUSY_MASK 0x00000001UL
+/* Xmit interrupt enable bit */
+#define XEL_TSR_XMIT_IE_MASK 0x00000008UL
+/* Buffer is active, SW bit only */
+#define XEL_TSR_XMIT_ACTIVE_MASK 0x80000000UL
+/* Program the MAC address */
+#define XEL_TSR_PROGRAM_MASK 0x00000002UL
+/* define for programming the MAC address into the EMAC Lite */
+#define XEL_TSR_PROG_MAC_ADDR (XEL_TSR_XMIT_BUSY_MASK |
XEL_TSR_PROGRAM_MASK)
+
+/* Transmit packet length upper byte */
+#define XEL_TPLR_LENGTH_MASK_HI 0x0000FF00UL
+/* Transmit packet length lower byte */
+#define XEL_TPLR_LENGTH_MASK_LO 0x000000FFUL
+
+/* Recv complete */
+#define XEL_RSR_RECV_DONE_MASK 0x00000001UL
+/* Recv interrupt enable bit */
+#define XEL_RSR_RECV_IE_MASK 0x00000008UL
+
+typedef struct {
+ unsigned int BaseAddress; /* Base address for device (IPIF) */
+ unsigned int NextTxBufferToUse; /* Next TX buffer to write to */
+ unsigned int NextRxBufferToUse; /* Next RX buffer to read from */
+ unsigned char DeviceId; /* Unique ID of device - for future */
+} XEmacLite;
+
+static XEmacLite EmacLite;
+
+static char etherrxbuff[PKTSIZE_ALIGN]; /* Receive buffer */
+
+/* hardcoded MAC address for the Xilinx EMAC Core when env is nowhere*/
+#ifdef CFG_ENV_IS_NOWHERE
+static u8 EMACAddr[ENET_ADDR_LENGTH] = { 0x00, 0x0a, 0x35, 0x00, 0x22,
0x01 };
+#endif
+
+void XEmacLite_AlignedRead (u32 * SrcPtr, void *DestPtr, unsigned
ByteCount)
+{
+ unsigned i;
+ unsigned Length = ByteCount;
+ u32 AlignBuffer;
+ u32 *To32Ptr;
+ u32 *From32Ptr;
+ u8 *To8Ptr;
+ u8 *From8Ptr;
+
+ From32Ptr = (u32 *) SrcPtr;
+
+ /* Word aligned buffer, no correction needed. */
+ To32Ptr = (u32 *) DestPtr;
+ while (Length > 3) {
+ *To32Ptr++ = *From32Ptr++;
+ Length -= 4;
+ }
+ To8Ptr = (u8 *) To32Ptr;
+
+ AlignBuffer = *From32Ptr++;
+ From8Ptr = (u8 *) & AlignBuffer;
+
+ for (i = 0; i < Length; i++) {
+ *To8Ptr++ = *From8Ptr++;
+ }
+}
+
+void XEmacLite_AlignedWrite (void *SrcPtr, u32 * DestPtr, unsigned
ByteCount)
+{
+ unsigned i;
+ unsigned Length = ByteCount;
+ u32 AlignBuffer;
+ u32 *To32Ptr;
+ u32 *From32Ptr;
+ u8 *To8Ptr;
+ u8 *From8Ptr;
+ To32Ptr = DestPtr;
+
+ From32Ptr = (u32 *) SrcPtr;
+ while (Length > 3) {
+
+ *To32Ptr++ = *From32Ptr++;
+ Length -= 4;
+ }
+
+ AlignBuffer = 0;
+ To8Ptr = (u8 *) & AlignBuffer;
+ From8Ptr = (u8 *) From32Ptr;
+
+ for (i = 0; i < Length; i++) {
+ *To8Ptr++ = *From8Ptr++;
+ }
+
+ *To32Ptr++ = AlignBuffer;
+}
+
+void eth_halt (void)
+{
+#ifdef DEBUG
+ puts ("eth_halt\n");
+#endif
+}
+
+int eth_init (bd_t * bis)
+{
+#ifdef DEBUG
+ puts ("EmacLite Initialization Started\n");
+#endif
+ memset (&EmacLite, 0, sizeof (XEmacLite));
+ EmacLite.BaseAddress = XILINX_EMACLITE_BASEADDR;
+
+#ifdef CFG_ENV_IS_NOWHERE
+ memcpy (bis->bi_enetaddr, EMACAddr, ENET_ADDR_LENGTH);
+#endif
+/*
+ * TX - TX_PING & TX_PONG initialization
+ */
+ /* Restart PING TX */
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET, 0);
+ /* Copy MAC address */
+ XEmacLite_AlignedWrite (bis->bi_enetaddr,
+ EmacLite.BaseAddress, ENET_ADDR_LENGTH);
+ /* Set the length */
+ out_be32 (EmacLite.BaseAddress + XEL_TPLR_OFFSET, ENET_ADDR_LENGTH);
+ /* Update the MAC address in the EMAC Lite */
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET, XEL_TSR_PROG_MAC_ADDR);
+ /* Wait for EMAC Lite to finish with the MAC address update */
+ while ((in_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET) &
+ XEL_TSR_PROG_MAC_ADDR) != 0) ;
+
+#ifdef XILINX_EMACLITE_TX_PING_PONG
+ /* The same operation with PONG TX */
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET + XEL_BUFFER_OFFSET, 0);
+ XEmacLite_AlignedWrite (bis->bi_enetaddr,
+ EmacLite.BaseAddress + XEL_BUFFER_OFFSET, ENET_ADDR_LENGTH);
+ out_be32 (EmacLite.BaseAddress + XEL_TPLR_OFFSET, ENET_ADDR_LENGTH);
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET + XEL_BUFFER_OFFSET,
+ XEL_TSR_PROG_MAC_ADDR);
+ while ((in_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET +
+ XEL_BUFFER_OFFSET) & XEL_TSR_PROG_MAC_ADDR) != 0) ;
+#endif
+
+/*
+ * RX - RX_PING & RX_PONG initialization
+ */
+ /* Write out the value to flush the RX buffer */
+ out_be32 (EmacLite.BaseAddress + XEL_RSR_OFFSET, XEL_RSR_RECV_IE_MASK);
+#ifdef XILINX_EMACLITE_RX_PING_PONG
+ out_be32 (EmacLite.BaseAddress + XEL_RSR_OFFSET + XEL_BUFFER_OFFSET,
+ XEL_RSR_RECV_IE_MASK);
+#endif
+
+#ifdef DEBUG
+ puts ("EmacLite Initialization complete\n");
+#endif
+ return 0;
+}
+
+int XEmacLite_TxBufferAvailable (XEmacLite * InstancePtr)
+{
+ u32 Register;
+ u32 TxPingBusy;
+ u32 TxPongBusy;
+ /*
+ * Read the other buffer register
+ * and determine if the other buffer is available
+ */
+ Register = in_be32 (InstancePtr->BaseAddress +
+ InstancePtr->NextTxBufferToUse + 0);
+ TxPingBusy = ((Register & XEL_TSR_XMIT_BUSY_MASK) ==
+ XEL_TSR_XMIT_BUSY_MASK);
+
+ Register = in_be32 (InstancePtr->BaseAddress +
+ (InstancePtr->NextTxBufferToUse ^ XEL_TSR_OFFSET) + 0);
+ TxPongBusy = ((Register & XEL_TSR_XMIT_BUSY_MASK) ==
+ XEL_TSR_XMIT_BUSY_MASK);
+
+ return (!(TxPingBusy && TxPongBusy));
+}
+
+int eth_send (volatile void *ptr, int len) {
+
+ unsigned int Register;
+ unsigned int BaseAddress;
+
+ unsigned maxtry = 1000;
+
+ if (len > ENET_MAX_MTU)
+ len = ENET_MAX_MTU;
+
+ while (!XEmacLite_TxBufferAvailable (&EmacLite) && maxtry) {
+ udelay (10);
+ maxtry--;
+ }
+
+ if (!maxtry) {
+ printf ("Error: Timeout waiting for ethernet TX buffer\n");
+ /* Restart PING TX */
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET, 0);
+#ifdef XILINX_EMACLITE_TX_PING_PONG
+ out_be32 (EmacLite.BaseAddress + XEL_TSR_OFFSET +
+ XEL_BUFFER_OFFSET, 0);
+#endif
+ return 0;
+ }
+
+ /* Determine the expected TX buffer address */
+ BaseAddress = (EmacLite.BaseAddress + EmacLite.NextTxBufferToUse);
+
+ /* Determine if the expected buffer address is empty */
+ Register = in_be32 (BaseAddress + XEL_TSR_OFFSET);
+ if (((Register & XEL_TSR_XMIT_BUSY_MASK) == 0)
+ && ((in_be32 ((BaseAddress) + XEL_TSR_OFFSET)
+ & XEL_TSR_XMIT_ACTIVE_MASK) == 0)) {
+
+#ifdef XILINX_EMACLITE_TX_PING_PONG
+ EmacLite.NextTxBufferToUse ^= XEL_BUFFER_OFFSET;
+#endif
+#ifdef DEBUG
+ printf ("Send packet from 0x%x\n", BaseAddress);
+#endif
+ /* Write the frame to the buffer */
+ XEmacLite_AlignedWrite (ptr, (u32 *) BaseAddress, len);
+ out_be32 (BaseAddress + XEL_TPLR_OFFSET,(len &
+ (XEL_TPLR_LENGTH_MASK_HI | XEL_TPLR_LENGTH_MASK_LO)));
+ Register = in_be32 (BaseAddress + XEL_TSR_OFFSET);
+ Register |= XEL_TSR_XMIT_BUSY_MASK;
+ if ((Register & XEL_TSR_XMIT_IE_MASK) != 0) {
+ Register |= XEL_TSR_XMIT_ACTIVE_MASK;
+ }
+ out_be32 (BaseAddress + XEL_TSR_OFFSET, Register);
+ return 1;
+ }
+#ifdef XILINX_EMACLITE_TX_PING_PONG
+ /* Switch to second buffer */
+ BaseAddress ^= XEL_BUFFER_OFFSET;
+ /* Determine if the expected buffer address is empty */
+ Register = in_be32 (BaseAddress + XEL_TSR_OFFSET);
+ if (((Register & XEL_TSR_XMIT_BUSY_MASK) == 0)
+ && ((in_be32 ((BaseAddress) + XEL_TSR_OFFSET)
+ & XEL_TSR_XMIT_ACTIVE_MASK) == 0)) {
+#ifdef DEBUG
+ printf ("Send packet from 0x%x\n", BaseAddress);
+#endif
+ /* Write the frame to the buffer */
+ XEmacLite_AlignedWrite (ptr, (u32 *) BaseAddress, len);
+ out_be32 (BaseAddress + XEL_TPLR_OFFSET,(len &
+ (XEL_TPLR_LENGTH_MASK_HI | XEL_TPLR_LENGTH_MASK_LO)));
+ Register = in_be32 (BaseAddress + XEL_TSR_OFFSET);
+ Register |= XEL_TSR_XMIT_BUSY_MASK;
+ if ((Register & XEL_TSR_XMIT_IE_MASK) != 0) {
+ Register |= XEL_TSR_XMIT_ACTIVE_MASK;
+ }
+ out_be32 (BaseAddress + XEL_TSR_OFFSET, Register);
+ return 1;
+ }
+#endif
+ puts ("Error while sending frame\n");
+ return 0;
+}
+
+int eth_rx (void)
+{
+ unsigned int Length;
+ unsigned int Register;
+ unsigned int BaseAddress;
+
+ BaseAddress = EmacLite.BaseAddress + EmacLite.NextRxBufferToUse;
+ Register = in_be32 (BaseAddress + XEL_RSR_OFFSET);
+#ifdef DEBUG
+ printf ("Testing data at address 0x%x\n", BaseAddress);
+#endif
+ if ((Register & XEL_RSR_RECV_DONE_MASK) == XEL_RSR_RECV_DONE_MASK) {
+#ifdef XILINX_EMACLITE_RX_PING_PONG
+ EmacLite.NextRxBufferToUse ^= XEL_BUFFER_OFFSET;
+#endif
+ } else {
+#ifndef XILINX_EMACLITE_RX_PING_PONG
+#ifdef DEBUG
+ printf ("No data was available - address 0x%x\n", BaseAddress);
+#endif
+ return 0;
+#else
+ BaseAddress ^= XEL_BUFFER_OFFSET;
+ Register = in_be32 (BaseAddress + XEL_RSR_OFFSET);
+ if ((Register & XEL_RSR_RECV_DONE_MASK) !=
+ XEL_RSR_RECV_DONE_MASK) {
+#ifdef DEBUG
+ printf ("No data was available - address 0x%x\n",
+ BaseAddress);
+#endif
+ return 0;
+ }
+#endif
+ }
+ /* Get the length of the frame that arrived */
+ switch(((in_be32(BaseAddress + XEL_RXBUFF_OFFSET + 0xC)) &
+ 0xFFFF0000 ) >> 16) {
+ case 0x806:
+ Length = 42 + 20; /* FIXME size of ARP */
+#ifdef DEBUG
+ puts ("ARP Packet\n");
+#endif
+ break;
+ case 0x800:
+ Length = 14 + 14 +
+ (((in_be32(BaseAddress + XEL_RXBUFF_OFFSET + 0x10)) &
+ 0xFFFF0000) >> 16); /* FIXME size of IP packet */
+#ifdef DEBUG
+ puts("IP Packet\n");
+#endif
+ break;
+ default:
+#ifdef DEBUG
+ puts("Other Packet\n");
+#endif
+ Length = ENET_MAX_MTU;
+ break;
+ }
+
+ XEmacLite_AlignedRead ((BaseAddress + XEL_RXBUFF_OFFSET),
+ etherrxbuff, Length);
+
+ /* Acknowledge the frame */
+ Register = in_be32 (BaseAddress + XEL_RSR_OFFSET);
+ Register &= ~XEL_RSR_RECV_DONE_MASK;
+ out_be32 (BaseAddress + XEL_RSR_OFFSET, Register);
+
+#ifdef DEBUG
+ printf ("Packet receive from 0x%x, length %dB\n", BaseAddress, Length);
+#endif
+ NetReceive ((uchar *) etherrxbuff, Length);
+ return 1;
+
+}
+#endif
diff --git a/fs/romfs/Makefile b/fs/romfs/Makefile
index e69de29..937d755 100644
--- a/fs/romfs/Makefile
+++ b/fs/romfs/Makefile
@@ -0,0 +1,49 @@
+#
+# (C) Copyright 2000-2006
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)libromfs.a
+
+AOBJS =
+COBJS = romfs.o
+
+SRCS := $(AOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(AOBJS) $(COBJS))
+
+#CPPFLAGS +=
+
+all: $(LIB) $(AOBJS)
+
+$(LIB): $(obj).depend $(OBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS)
+
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
More information about the U-Boot
mailing list