[U-Boot-Users] [PATCH 9/9 RESUBMIT] Add support for Korat PPC440EPx board

Larry Johnson lrj at arlinx.com
Thu Dec 27 17:28:51 CET 2007


These patches add support for the PPC440EPx-based "Korat" board to
U-Boot.  They are based primarily on support for the Sequoia board.

Signed-off-by: Larry Johnson <lrj at acm.org>
---
 MAINTAINERS            |    4 +
 MAKEALL                |    1 +
 Makefile               |    3 +
 board/korat/Makefile   |   51 ++++
 board/korat/config.mk  |   37 +++
 board/korat/init.S     |   80 +++++
 board/korat/korat.c    |  761 ++++++++++++++++++++++++++++++++++++++++++++++++
 board/korat/u-boot.lds |  145 +++++++++
 8 files changed, 1082 insertions(+), 0 deletions(-)
 create mode 100644 board/korat/Makefile
 create mode 100644 board/korat/config.mk
 create mode 100644 board/korat/init.S
 create mode 100644 board/korat/korat.c
 create mode 100644 board/korat/u-boot.lds

diff --git a/MAINTAINERS b/MAINTAINERS
index bf0ebb1..0238d2e 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -204,6 +204,10 @@ Murray Jensen <Murray.Jensen at csiro.au>
 	cogent_mpc8260		MPC8260
 	hymod			MPC8260
 
+Larry Johnson <lrj at acm.org>
+
+	korat			PPC440EPx
+
 Brad Kemp <Brad.Kemp at seranoa.com>
 
 	ppmc8260		MPC8260
diff --git a/MAKEALL b/MAKEALL
index fb53a91..97e3891 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -191,6 +191,7 @@ LIST_4xx="		\
 	katmai		\
 	kilauea		\
 	kilauea_nand	\
+	korat		\
 	luan		\
 	lwmon5		\
 	makalu		\
diff --git a/Makefile b/Makefile
index c73d4cf..c127bcf 100644
--- a/Makefile
+++ b/Makefile
@@ -1231,6 +1231,9 @@ haleakala_nand_config: unconfig
 	@echo "TEXT_BASE = 0x01000000" > $(obj)board/amcc/kilauea/config.tmp
 	@echo "CONFIG_NAND_U_BOOT = y" >> $(obj)include/config.mk
 
+korat_config:	unconfig
+	@$(MKCONFIG) $(@:_config=) ppc ppc4xx korat
+
 luan_config:	unconfig
 	@$(MKCONFIG) $(@:_config=) ppc ppc4xx luan amcc
 
diff --git a/board/korat/Makefile b/board/korat/Makefile
new file mode 100644
index 0000000..fa19e6f
--- /dev/null
+++ b/board/korat/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2002-2007
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB	= $(obj)lib$(BOARD).a
+
+COBJS	= $(BOARD).o
+SOBJS	= init.o
+
+SRCS	:= $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS	:= $(addprefix $(obj),$(COBJS))
+SOBJS	:= $(addprefix $(obj),$(SOBJS))
+
+$(LIB):	$(OBJS) $(SOBJS)
+	$(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+	rm -f $(SOBJS) $(OBJS)
+
+distclean:	clean
+	rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/korat/config.mk b/board/korat/config.mk
new file mode 100644
index 0000000..39966e0
--- /dev/null
+++ b/board/korat/config.mk
@@ -0,0 +1,37 @@
+#
+# (C) Copyright 2002
+# Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+# MA 02111-1307 USA
+#
+#
+# Korat (PPC440EPx) board
+#
+
+TEXT_BASE = 0xFFFA0000
+
+PLATFORM_CPPFLAGS += -DCONFIG_440=1
+
+ifeq ($(debug),1)
+PLATFORM_CPPFLAGS += -DDEBUG
+endif
+
+ifeq ($(dbcr),1)
+PLATFORM_CPPFLAGS += -DCFG_INIT_DBCR=0x8cff0000
+endif
diff --git a/board/korat/init.S b/board/korat/init.S
new file mode 100644
index 0000000..bd0e8b4
--- /dev/null
+++ b/board/korat/init.S
@@ -0,0 +1,80 @@
+/*
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.	 See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <ppc_asm.tmpl>
+#include <asm-ppc/mmu.h>
+#include <config.h>
+
+/**************************************************************************
+ * TLB TABLE
+ *
+ * This table is used by the cpu boot code to setup the initial tlb
+ * entries. Rather than make broad assumptions in the cpu source tree,
+ * this table lets each board set things up however they like.
+ *
+ *  Pointer to the table is returned in r1
+ *
+ *************************************************************************/
+    .section .bootpg,"ax"
+    .globl tlbtab
+
+tlbtab:
+	tlbtab_start
+
+	/*
+	 * BOOT_CS (FLASH) must be first. Before relocation SA_I can be off to use the
+	 * speed up boot process. It is patched after relocation to enable SA_I
+	 */
+	tlbentry( CFG_BOOT_BASE_ADDR, SZ_256M, CFG_BOOT_BASE_ADDR, 1, AC_R|AC_W|AC_X|SA_G )
+
+	/*
+	 * TLB entries for SDRAM are not needed on this platform.  They are
+	 * generated dynamically in the SPD DDR2 detection routine.
+	 */
+
+#ifdef CFG_INIT_RAM_DCACHE
+	/* TLB-entry for init-ram in dcache (SA_I must be turned off!) */
+	tlbentry( CFG_INIT_RAM_ADDR, SZ_64K, CFG_INIT_RAM_ADDR, 0, AC_R|AC_W|AC_X|SA_G )
+#endif
+
+	/* TLB-entry for PCI Memory */
+	tlbentry( CFG_PCI_MEMBASE, SZ_256M, CFG_PCI_MEMBASE, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE1, SZ_256M, CFG_PCI_MEMBASE1, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE2, SZ_256M, CFG_PCI_MEMBASE2, 1, AC_R|AC_W|SA_G|SA_I )
+	tlbentry( CFG_PCI_MEMBASE3, SZ_256M, CFG_PCI_MEMBASE3, 1, AC_R|AC_W|SA_G|SA_I )
+
+	/* TLB-entry for EBC */
+	tlbentry( CFG_CPLD_BASE, SZ_1K, CFG_CPLD_BASE, 1, AC_R|AC_W|SA_G|SA_I )
+
+	/* TLB-entry for Internal Registers & OCM */
+	/* I wonder why this must be executable -- lrj at acm.org 2007-10-08 */
+	tlbentry( 0xE0000000, SZ_16M, 0xE0000000, 0,  AC_R|AC_W|AC_X|SA_I )
+
+	/*TLB-entry PCI registers*/
+	tlbentry( 0xEEC00000, SZ_1K, 0xEEC00000, 1,  AC_R|AC_W|SA_G|SA_I )
+
+	/* TLB-entry for peripherals */
+	tlbentry( 0xEF000000, SZ_16M, 0xEF000000, 1, AC_R|AC_W|SA_G|SA_I)
+
+	/* TLB-entry PCI IO Space - from sr at denx.de */
+	tlbentry(0xE8000000, SZ_64K, 0xE8000000, 1, AC_R|AC_W|SA_G|SA_I)
+
+	tlbtab_end
diff --git a/board/korat/korat.c b/board/korat/korat.c
new file mode 100644
index 0000000..7cb9ee1
--- /dev/null
+++ b/board/korat/korat.c
@@ -0,0 +1,761 @@
+/*
+ * (C) Copyright 2007
+ * Larry Johnson, lrj at acm.org
+ *
+ * (C) Copyright 2006
+ * Stefan Roese, DENX Software Engineering, sr at denx.de.
+ *
+ * (C) Copyright 2006
+ * Jacqueline Pira-Ferriol, AMCC/IBM, jpira-ferriol at fr.ibm.com
+ * Alain Saurel,	    AMCC/IBM, alain.saurel at fr.ibm.com
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <asm/processor.h>
+#include <asm-ppc/io.h>
+#include <i2c.h>
+#include <ppc440.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+extern flash_info_t flash_info[CFG_MAX_FLASH_BANKS];	/* info for FLASH chips    */
+
+ulong flash_get_size(ulong base, int banknum);
+
+int board_early_init_f(void)
+{
+	u32 sdr0_pfc1, sdr0_pfc2;
+	u32 gpio0_ir;
+	u32 reg;
+	int eth;
+
+	mtdcr(ebccfga, xbcfg);
+	mtdcr(ebccfgd, 0xb8400000);
+
+	/*--------------------------------------------------------------------
+	 * Setup the GPIO pins
+	 *
+	 * Korat GPIO usage:
+	 *
+	 *                   Init.
+	 * Pin    Source I/O value Function
+	 * ------ ------ --- ----- ---------------------------------
+	 * GPIO00  Alt1  I/O   x   PerAddr07
+	 * GPIO01  Alt1  I/O   x   PerAddr06
+	 * GPIO02  Alt1  I/O   x   PerAddr05
+	 * GPIO03  GPIO   x    x   GPIO03 to expansion bus connector
+	 * GPIO04  GPIO   x    x   GPIO04 to expansion bus connector
+	 * GPIO05  GPIO   x    x   GPIO05 to expansion bus connector
+	 * GPIO06  Alt1   O    x   PerCS1 (2nd NOR flash)
+	 * GPIO07  Alt1   O    x   PerCS2 (CPLD)
+	 * GPIO08  Alt1   O    x   PerCS3 to expansion bus connector
+	 * GPIO09  Alt1   O    x   PerCS4 to expansion bus connector
+	 * GPIO10  Alt1   O    x   PerCS5 to expansion bus connector
+	 * GPIO11  Alt1   I    x   PerErr
+	 * GPIO12  GPIO   O    0   ATMega !Reset
+	 * GPIO13  GPIO   O    1   SPI Atmega !SS
+	 * GPIO14  GPIO   O    1   Write protect EEPROM #1 (0xA8)
+	 * GPIO15  GPIO   O    0   CPU Run LED !On
+	 * GPIO16  Alt1   O    x   GMC1TxD0
+	 * GPIO17  Alt1   O    x   GMC1TxD1
+	 * GPIO18  Alt1   O    x   GMC1TxD2
+	 * GPIO19  Alt1   O    x   GMC1TxD3
+	 * GPIO20  Alt1   O    x   RejectPkt0
+	 * GPIO21  Alt1   O    x   RejectPkt1
+	 * GPIO22  GPIO   I    x   PGOOD_DDR
+	 * GPIO23  Alt1   O    x   SCPD0
+	 * GPIO24  Alt1   O    x   GMC0TxD2
+	 * GPIO25  Alt1   O    x   GMC0TxD3
+	 * GPIO26  GPIO? I/O   x   IIC0SDA (selected in SDR0_PFC4)
+	 * GPIO27  GPIO   O    0   PHY #0 1000BASE-X
+	 * GPIO28  GPIO   O    0   PHY #1 1000BASE-X
+	 * GPIO29  GPIO   I    x   Test jumper !Present
+	 * GPIO30  GPIO   I    x   SFP module #0 !Present
+	 * GPIO31  GPIO   I    x   SFP module #1 !Present
+	 *
+	 * GPIO32  GPIO   O    1   SFP module #0 Tx !Enable
+	 * GPIO33  GPIO   O    1   SFP module #1 Tx !Enable
+	 * GPIO34  Alt2   I    x   !UART1_CTS
+	 * GPIO35  Alt2   O    x   !UART1_RTS
+	 * GPIO36  Alt1   I    x   !UART0_CTS
+	 * GPIO37  Alt1   O    x   !UART0_RTS
+	 * GPIO38  Alt2   O    x   UART1_Tx
+	 * GPIO39  Alt2   I    x   UART1_Rx
+	 * GPIO40  Alt1   I    x   IRQ0 (Ethernet 0)
+	 * GPIO41  Alt1   I    x   IRQ1 (Ethernet 1)
+	 * GPIO42  Alt1   I    x   IRQ2 (PCI interrupt)
+	 * GPIO43  Alt1   I    x   IRQ3 (System Alert from CPLD)
+	 * GPIO44  xxxx   x    x   (grounded through pulldown)
+	 * GPIO45  GPIO   O    0   PHY #0 Enable
+	 * GPIO46  GPIO   O    0   PHY #1 Enable
+	 * GPIO47  GPIO   I    x   Reset switch !Pressed
+	 * GPIO48  GPIO   I    x   Shutdown switch !Pressed
+	 * GPIO49  xxxx   x    x   (reserved for trace port)
+	 *   .      .     .    .               .
+	 *   .      .     .    .               .
+	 *   .      .     .    .               .
+	 * GPIO63  xxxx   x    x   (reserved for trace port)
+	 *-------------------------------------------------------------------*/
+
+	out_be32((u32 *) GPIO0_OR, 0x00060000);
+	out_be32((u32 *) GPIO1_OR, 0xC0000000);
+
+	out_be32((u32 *) GPIO0_OSRL, 0x54055400);
+	out_be32((u32 *) GPIO0_OSRH, 0x55015000);
+	out_be32((u32 *) GPIO1_OSRL, 0x02180000);
+	out_be32((u32 *) GPIO1_OSRH, 0x00000000);
+
+	out_be32((u32 *) GPIO0_TSRL, 0x54055500);
+	out_be32((u32 *) GPIO0_TSRH, 0x00015000);
+	out_be32((u32 *) GPIO1_TSRL, 0x00000000);
+	out_be32((u32 *) GPIO1_TSRH, 0x00000000);
+
+	out_be32((u32 *) GPIO0_TCR, 0x000FF0D8);
+	out_be32((u32 *) GPIO1_TCR, 0xD6060000);
+
+	out_be32((u32 *) GPIO0_ISR1L, 0x54000100);
+	out_be32((u32 *) GPIO0_ISR1H, 0x00500000);
+	out_be32((u32 *) GPIO1_ISR1L, 0x00405500);
+	out_be32((u32 *) GPIO1_ISR1H, 0x00000000);
+
+	out_be32((u32 *) GPIO0_ISR2L, 0x00000000);
+	out_be32((u32 *) GPIO0_ISR2H, 0x00000000);
+	out_be32((u32 *) GPIO1_ISR2L, 0x04010000);
+	out_be32((u32 *) GPIO1_ISR2H, 0x00000000);
+
+	out_be32((u32 *) GPIO0_ISR3L, 0x00000000);
+	out_be32((u32 *) GPIO0_ISR3H, 0x00000000);
+	out_be32((u32 *) GPIO1_ISR3L, 0x00000000);
+	out_be32((u32 *) GPIO1_ISR3H, 0x00000000);
+
+	/*--------------------------------------------------------------------
+	 * Setup the interrupt controller polarities, triggers, etc.
+	 *-------------------------------------------------------------------*/
+	mtdcr(uic0sr, 0xffffffff);	/* clear all */
+	mtdcr(uic0er, 0x00000000);	/* disable all */
+	mtdcr(uic0cr, 0x00000005);	/* ATI & UIC1 crit are critical */
+	mtdcr(uic0pr, 0xfffff7ff);	/* per ref-board manual */
+	mtdcr(uic0tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic0vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic0sr, 0xffffffff);	/* clear all */
+
+	mtdcr(uic1sr, 0xffffffff);	/* clear all */
+	mtdcr(uic1er, 0x00000000);	/* disable all */
+	mtdcr(uic1cr, 0x00000000);	/* all non-critical */
+	mtdcr(uic1pr, 0xffffffff);	/* per ref-board manual */
+	mtdcr(uic1tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic1vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic1sr, 0xffffffff);	/* clear all */
+
+	mtdcr(uic2sr, 0xffffffff);	/* clear all */
+	mtdcr(uic2er, 0x00000000);	/* disable all */
+	mtdcr(uic2cr, 0x00000000);	/* all non-critical */
+	mtdcr(uic2pr, 0xffffffff);	/* per ref-board manual */
+	mtdcr(uic2tr, 0x00000000);	/* per ref-board manual */
+	mtdcr(uic2vr, 0x00000000);	/* int31 highest, base=0x000 */
+	mtdcr(uic2sr, 0xffffffff);	/* clear all */
+
+	/* take sim card reader and CF controller out of reset */
+	out_8((u8 *) CFG_CPLD_BASE + 0x04, 0x80);
+
+	/* Configure the two Ethernet PHYs.  For each PHY, configure for fiber
+	 * if the SFP module is present, and for copper if it is not present.
+	 */
+	gpio0_ir = in_be32((u32 *) GPIO0_IR);
+	for (eth = 0; eth < 2; ++eth) {
+		if (gpio0_ir & (0x00000001 << (1 - eth))) {
+			/* SFP module not present: configure PHY for copper. */
+			/* Set PHY to autonegotate 10 MB, 100MB, or 1 GB */
+			out_8((u8 *) CFG_CPLD_BASE + 0x06,
+			      in_8((u8 *) CFG_CPLD_BASE + 0x06) |
+			      0x06 << (4 * eth));
+		} else {
+			/* SFP module present: configure PHY for fiber and
+			   enable output */
+			out_be32((u32 *) GPIO0_OR, in_be32((u32 *) GPIO0_OR) |
+				 (0x00000001 << (4 - eth)));
+			out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) &
+				 ~(0x00000001 << (31 - eth)));
+		}
+	}
+	/* enable Ethernet: set GPIO45 and GPIO46 to 1 */
+	out_be32((u32 *) GPIO1_OR, in_be32((u32 *) GPIO1_OR) | 0x00060000);
+
+	/* select Ethernet pins */
+	mfsdr(SDR0_PFC1, sdr0_pfc1);
+	sdr0_pfc1 = (sdr0_pfc1 & ~SDR0_PFC1_SELECT_MASK) |
+	    SDR0_PFC1_SELECT_CONFIG_4;
+	mfsdr(SDR0_PFC2, sdr0_pfc2);
+	sdr0_pfc2 = (sdr0_pfc2 & ~SDR0_PFC2_SELECT_MASK) |
+	    SDR0_PFC2_SELECT_CONFIG_4;
+	mtsdr(SDR0_PFC2, sdr0_pfc2);
+	mtsdr(SDR0_PFC1, sdr0_pfc1);
+
+	/* PCI arbiter enabled */
+	mfsdr(sdr_pci0, reg);
+	mtsdr(sdr_pci0, 0x80000000 | reg);
+
+	return 0;
+}
+
+static int man_data_read(unsigned int addr)
+{
+	/*
+	 * Read an octet of data from address "addr" in the manufacturer's
+	 * information serial EEPROM, or -1 on error.
+	 */
+	u8 data[2];
+
+	if (0 != i2c_probe(MAN_DATA_EEPROM_ADDR) ||
+	    0 != i2c_read(MAN_DATA_EEPROM_ADDR, addr, 1, data, 1)) {
+		debug("man_data_read(0x%02X) failed\n", addr);
+		return -1;
+	}
+	debug("man_info_read(0x%02X) returned 0x%02X\n", addr, data[0]);
+	return data[0];
+}
+
+static unsigned int man_data_field_addr(unsigned int const field)
+{
+	/*
+	 * The manufacturer's information serial EEPROM contains a sequence of
+	 * zero-delimited fields.  Return the starting address of field "field",
+	 * or 0 on error.
+	 */
+	unsigned addr, i;
+
+	if (0 == field || 'A' != man_data_read(0) || '\0' != man_data_read(1))
+		/* Only format "A" is currently supported */
+		return 0;
+
+	for (addr = 2, i = 1; i < field && addr < 256; ++addr) {
+		if ('\0' == man_data_read(addr))
+			++i;
+	}
+	return (addr < 256) ? addr : 0;
+}
+
+static char *man_data_read_field(char s[], unsigned const field,
+				 unsigned const length)
+{
+	/*
+	 * Place the null-terminated contents of field "field" of length
+	 * "length" from the manufacturer's information serial EEPROM into
+	 * string "s[length + 1]" and return a pointer to s, or return 0 on
+	 * error. In either case the original contents of s[] is not preserved.
+	 */
+	unsigned addr, i;
+
+	addr = man_data_field_addr(field);
+	if (0 == addr || addr + length >= 255)
+		return 0;
+
+	for (i = 0; i < length; ++i) {
+		int const c = man_data_read(addr++);
+
+		if (c <= 0)
+			return 0;
+
+		s[i] = (char)c;
+	}
+	if (0 != man_data_read(addr))
+		return 0;
+
+	s[i] = '\0';
+	return s;
+}
+
+static void set_serial_number(void)
+{
+	/*
+	 * If the environmental variable "serial#" is not set, try to set it
+	 * from the manufacturer's information serial EEPROM.
+	 */
+	char s[MAN_SERIAL_NO_LENGTH + 1];
+
+	if (0 == getenv("serial#") &&
+	    0 != man_data_read_field(s, MAN_SERIAL_NO_FIELD,
+				     MAN_SERIAL_NO_LENGTH))
+		setenv("serial#", s);
+}
+
+static void set_mac_addresses(void)
+{
+	/*
+	 * If the environmental variables "ethaddr" and/or "eth1addr" are not
+	 * set, try to set them from the manufacturer's information serial
+	 * EEPROM.
+	 */
+	char s[MAN_MAC_ADDR_LENGTH + 1];
+
+	if (0 != getenv("ethaddr") && 0 != getenv("eth1addr"))
+		return;
+
+	if (0 == man_data_read_field(s, MAN_MAC_ADDR_FIELD,
+				     MAN_MAC_ADDR_LENGTH))
+		return;
+
+	if (0 == getenv("ethaddr"))
+		setenv("ethaddr", s);
+
+	if (0 == getenv("eth1addr")) {
+		++s[MAN_MAC_ADDR_LENGTH - 1];
+		setenv("eth1addr", s);
+	}
+}
+
+/*---------------------------------------------------------------------------+
+  | misc_init_r.
+  +---------------------------------------------------------------------------*/
+int misc_init_r(void)
+{
+	uint pbcr;
+	int size_val = 0;
+	u32 reg;
+	unsigned long usb2d0cr = 0;
+	unsigned long usb2phy0cr, usb2h0cr = 0;
+	unsigned long sdr0_pfc1;
+	char *act = getenv("usbact");
+
+	/*
+	 * FLASH stuff...
+	 */
+
+	/* Re-do sizing to get full correct info */
+
+	/* adjust flash start and offset */
+	gd->bd->bi_flashstart = 0 - gd->bd->bi_flashsize;
+	gd->bd->bi_flashoffset = 0;
+
+	mtdcr(ebccfga, pb0cr);
+	pbcr = mfdcr(ebccfgd);
+	switch (gd->bd->bi_flashsize) {
+	case 1 << 20:
+		size_val = 0;
+		break;
+	case 2 << 20:
+		size_val = 1;
+		break;
+	case 4 << 20:
+		size_val = 2;
+		break;
+	case 8 << 20:
+		size_val = 3;
+		break;
+	case 16 << 20:
+		size_val = 4;
+		break;
+	case 32 << 20:
+		size_val = 5;
+		break;
+	case 64 << 20:
+		size_val = 6;
+		break;
+	case 128 << 20:
+		size_val = 7;
+		break;
+	}
+	pbcr = (pbcr & 0x0001ffff) | gd->bd->bi_flashstart | (size_val << 17);
+	mtdcr(ebccfga, pb0cr);
+	mtdcr(ebccfgd, pbcr);
+
+	/*
+	 * Re-check to get correct base address
+	 */
+	flash_get_size(gd->bd->bi_flashstart, 0);
+
+	/* Monitor protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET, -CFG_MONITOR_LEN, 0xffffffff,
+			    &flash_info[0]);
+
+	/* Env protection ON by default */
+	(void)flash_protect(FLAG_PROTECT_SET,
+			    CFG_ENV_ADDR_REDUND,
+			    CFG_ENV_ADDR_REDUND + 2 * CFG_ENV_SECT_SIZE - 1,
+			    &flash_info[0]);
+
+	/*
+	 * USB suff...
+	 */
+	if (act == NULL || strcmp(act, "hostdev") == 0) {
+		/* SDR Setting */
+		mfsdr(SDR0_PFC1, sdr0_pfc1);
+		mfsdr(SDR0_USB2D0CR, usb2d0cr);
+		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+		mfsdr(SDR0_USB2H0CR, usb2h0cr);
+
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_16BIT_30MHZ;	/*1 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;	/*1 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;	/*1 */
+
+		/* An 8-bit/60MHz interface is the only possible alternative
+		   when connecting the Device to the PHY */
+		usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK;
+		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_16BIT_30MHZ;	/*1 */
+
+		/* To enable the USB 2.0 Device function through the UTMI interface */
+		usb2d0cr = usb2d0cr & ~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
+		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_USB2DEV_SELECTION;	/*1 */
+
+		sdr0_pfc1 = sdr0_pfc1 & ~SDR0_PFC1_UES_MASK;
+		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_USB2D_SEL;	/*0 */
+
+		mtsdr(SDR0_PFC1, sdr0_pfc1);
+		mtsdr(SDR0_USB2D0CR, usb2d0cr);
+		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+		mtsdr(SDR0_USB2H0CR, usb2h0cr);
+
+		/*clear resets */
+		udelay(1000);
+		mtsdr(SDR0_SRST1, 0x00000000);
+		udelay(1000);
+		mtsdr(SDR0_SRST0, 0x00000000);
+
+		printf("USB:   Host(int phy) Device(ext phy)\n");
+
+	} else if (strcmp(act, "dev") == 0) {
+		/*-------------------PATCH-------------------------------*/
+		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PURDIS;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_HOST;	/*1 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_HOST;	/*1 */
+		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+
+		udelay(1000);
+		mtsdr(SDR0_SRST1, 0x672c6000);
+
+		udelay(1000);
+		mtsdr(SDR0_SRST0, 0x00000080);
+
+		udelay(1000);
+		mtsdr(SDR0_SRST1, 0x60206000);
+
+		*(unsigned int *)(0xe0000350) = 0x00000001;
+
+		udelay(1000);
+		mtsdr(SDR0_SRST1, 0x60306000);
+		/*-------------------PATCH-------------------------------*/
+
+		/* SDR Setting */
+		mfsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+		mfsdr(SDR0_USB2H0CR, usb2h0cr);
+		mfsdr(SDR0_USB2D0CR, usb2d0cr);
+		mfsdr(SDR0_PFC1, sdr0_pfc1);
+
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_XOCLK_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_XOCLK_EXTERNAL;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_WDINT_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_WDINT_8BIT_60MHZ;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DVBUS_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DVBUS_PUREN;	/*1 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_DWNSTR_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_DWNSTR_DEV;	/*0 */
+		usb2phy0cr = usb2phy0cr & ~SDR0_USB2PHY0CR_UTMICN_MASK;
+		usb2phy0cr = usb2phy0cr | SDR0_USB2PHY0CR_UTMICN_DEV;	/*0 */
+
+		usb2h0cr = usb2h0cr & ~SDR0_USB2H0CR_WDINT_MASK;
+		usb2h0cr = usb2h0cr | SDR0_USB2H0CR_WDINT_8BIT_60MHZ;	/*0 */
+
+		usb2d0cr = usb2d0cr & ~SDR0_USB2D0CR_USB2DEV_EBC_SEL_MASK;
+		usb2d0cr = usb2d0cr | SDR0_USB2D0CR_EBC_SELECTION;	/*0 */
+
+		sdr0_pfc1 = sdr0_pfc1 & ~SDR0_PFC1_UES_MASK;
+		sdr0_pfc1 = sdr0_pfc1 | SDR0_PFC1_UES_EBCHR_SEL;	/*1 */
+
+		mtsdr(SDR0_USB2H0CR, usb2h0cr);
+		mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
+		mtsdr(SDR0_USB2D0CR, usb2d0cr);
+		mtsdr(SDR0_PFC1, sdr0_pfc1);
+
+		/*clear resets */
+		udelay(1000);
+		mtsdr(SDR0_SRST1, 0x00000000);
+		udelay(1000);
+		mtsdr(SDR0_SRST0, 0x00000000);
+
+		printf("USB:   Device(int phy)\n");
+	}
+
+	mfsdr(SDR0_SRST1, reg);	/* enable security/kasumi engines */
+	reg &= ~(SDR0_SRST1_CRYP0 | SDR0_SRST1_KASU0);
+	mtsdr(SDR0_SRST1, reg);
+
+	/*
+	 * Clear PLB4A0_ACR[WRP]
+	 * This fix will make the MAL burst disabling patch for the Linux
+	 * EMAC driver obsolete.
+	 */
+	reg = mfdcr(plb4_acr) & ~PLB4_ACR_WRP;
+	mtdcr(plb4_acr, reg);
+
+	set_serial_number();
+	set_mac_addresses();
+	return 0;
+}
+
+int checkboard(void)
+{
+	char const *const s = getenv("serial#");
+	u8 const rev = in_8((u8 *) CFG_CPLD_BASE + 0);
+	u32 const gpio0_or = in_be32((u32 *) GPIO0_OR);
+
+	printf("Board: Korat, Rev. %X", rev);
+	if (s != NULL)
+		printf(", serial# %s", s);
+
+	printf(", Ethernet PHY 0: ");
+	if (gpio0_or & 0x00000010)
+		printf("fiber");
+	else
+		printf("copper");
+
+	printf(", PHY 1: ");
+	if (gpio0_or & 0x00000008)
+		printf("fiber");
+	else
+		printf("copper");
+
+	printf(".\n");
+	return (0);
+}
+
+#if defined(CFG_DRAM_TEST)
+int testdram(void)
+{
+	unsigned long *mem = (unsigned long *)0;
+	const unsigned long kend = (1024 / sizeof(unsigned long));
+	unsigned long k, n;
+
+	mtmsr(0);
+
+	/* TODO: find correct size of SDRAM */
+	for (k = 0; k < CFG_MBYTES_SDRAM;
+	     ++k, mem += (1024 / sizeof(unsigned long))) {
+		if ((k & 1023) == 0)
+			printf("%3d MB\r", k / 1024);
+
+		memset(mem, 0xaaaaaaaa, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0xaaaaaaaa) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+
+		memset(mem, 0x55555555, 1024);
+		for (n = 0; n < kend; ++n) {
+			if (mem[n] != 0x55555555) {
+				printf("SDRAM test fails at: %08x\n",
+				       (uint) & mem[n]);
+				return 1;
+			}
+		}
+	}
+	printf("SDRAM test passes\n");
+	return 0;
+}
+#endif /* defined(CFG_DRAM_TEST) */
+
+/*************************************************************************
+ *  pci_pre_init
+ *
+ *  This routine is called just prior to registering the hose and gives
+ *  the board the opportunity to check things. Returning a value of zero
+ *  indicates that things are bad & PCI initialization should be aborted.
+ *
+ *	Different boards may wish to customize the pci controller structure
+ *	(add regions, override default access routines, etc) or perform
+ *	certain pre-initialization actions.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int pci_pre_init(struct pci_controller *hose)
+{
+	unsigned long addr;
+
+	/*-------------------------------------------------------------------------+
+	  | Set priority for all PLB3 devices to 0.
+	  | Set PLB3 arbiter to fair mode.
+	  +-------------------------------------------------------------------------*/
+	mfsdr(sdr_amp1, addr);
+	mtsdr(sdr_amp1, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb3_acr);
+	mtdcr(plb3_acr, addr | 0x80000000);
+
+	/*-------------------------------------------------------------------------+
+	  | Set priority for all PLB4 devices to 0.
+	  +-------------------------------------------------------------------------*/
+	mfsdr(sdr_amp0, addr);
+	mtsdr(sdr_amp0, (addr & 0x000000FF) | 0x0000FF00);
+	addr = mfdcr(plb4_acr) | 0xa0000000;	/* Was 0x8---- */
+	mtdcr(plb4_acr, addr);
+
+	/*-------------------------------------------------------------------------+
+	  | Set Nebula PLB4 arbiter to fair mode.
+	  +-------------------------------------------------------------------------*/
+	/* Segment0 */
+	addr = (mfdcr(plb0_acr) & ~plb0_acr_ppm_mask) | plb0_acr_ppm_fair;
+	addr = (addr & ~plb0_acr_hbu_mask) | plb0_acr_hbu_enabled;
+	addr = (addr & ~plb0_acr_rdp_mask) | plb0_acr_rdp_4deep;
+	addr = (addr & ~plb0_acr_wrp_mask) | plb0_acr_wrp_2deep;
+	mtdcr(plb0_acr, addr);
+
+	/* Segment1 */
+	addr = (mfdcr(plb1_acr) & ~plb1_acr_ppm_mask) | plb1_acr_ppm_fair;
+	addr = (addr & ~plb1_acr_hbu_mask) | plb1_acr_hbu_enabled;
+	addr = (addr & ~plb1_acr_rdp_mask) | plb1_acr_rdp_4deep;
+	addr = (addr & ~plb1_acr_wrp_mask) | plb1_acr_wrp_2deep;
+	mtdcr(plb1_acr, addr);
+
+	return 1;
+}
+#endif /* defined(CONFIG_PCI) */
+
+/*************************************************************************
+ *  pci_target_init
+ *
+ *	The bootstrap configuration provides default settings for the pci
+ *	inbound map (PIM). But the bootstrap config choices are limited and
+ *	may not be sufficient for a given board.
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT)
+void pci_target_init(struct pci_controller *hose)
+{
+	/*--------------------------------------------------------------------------+
+	 * Set up Direct MMIO registers
+	 *--------------------------------------------------------------------------*/
+	/*--------------------------------------------------------------------------+
+	  | PowerPC440EPX PCI Master configuration.
+	  | Map one 1Gig range of PLB/processor addresses to PCI memory space.
+	  |   PLB address 0xA0000000-0xDFFFFFFF ==> PCI address 0xA0000000-0xDFFFFFFF
+	  |   Use byte reversed out routines to handle endianess.
+	  | Make this region non-prefetchable.
+	  +--------------------------------------------------------------------------*/
+	out32r(PCIX0_PMM0MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM0LA, CFG_PCI_MEMBASE);	/* PMM0 Local Address */
+	out32r(PCIX0_PMM0PCILA, CFG_PCI_MEMBASE);	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM0PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	out32r(PCIX0_PMM0MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
+
+	out32r(PCIX0_PMM1MA, 0x00000000);	/* PMM0 Mask/Attribute - disabled b4 setting */
+	out32r(PCIX0_PMM1LA, CFG_PCI_MEMBASE2);	/* PMM0 Local Address */
+	out32r(PCIX0_PMM1PCILA, CFG_PCI_MEMBASE2);	/* PMM0 PCI Low Address */
+	out32r(PCIX0_PMM1PCIHA, 0x00000000);	/* PMM0 PCI High Address */
+	out32r(PCIX0_PMM1MA, 0xE0000001);	/* 512M + No prefetching, and enable region */
+
+	out32r(PCIX0_PTM1MS, 0x00000001);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM1LA, 0);	/* Local Addr. Reg */
+	out32r(PCIX0_PTM2MS, 0);	/* Memory Size/Attribute */
+	out32r(PCIX0_PTM2LA, 0);	/* Local Addr. Reg */
+
+	/*--------------------------------------------------------------------------+
+	 * Set up Configuration registers
+	 *--------------------------------------------------------------------------*/
+
+	/* Program the board's subsystem id/vendor id */
+	pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
+			      CFG_PCI_SUBSYS_VENDORID);
+	pci_write_config_word(0, PCI_SUBSYSTEM_ID, CFG_PCI_SUBSYS_ID);
+
+	/* Configure command register as bus master */
+	pci_write_config_word(0, PCI_COMMAND, PCI_COMMAND_MASTER);
+
+	/* 240nS PCI clock */
+	pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+
+	/* No error reporting */
+	pci_write_config_word(0, PCI_ERREN, 0);
+
+	pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
+
+	/*--------------------------------------------------------------------------+
+	 * Set up Configuration registers for on-board NEC uPD720101 USB controller
+	 *--------------------------------------------------------------------------*/
+	pci_write_config_dword(PCI_BDF(0x0, 0xC, 0x0), 0xE4, 0x00000020);
+}
+#endif /* defined(CONFIG_PCI) && defined(CFG_PCI_TARGET_INIT) */
+
+/*************************************************************************
+ *  pci_master_init
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI) && defined(CFG_PCI_MASTER_INIT)
+void pci_master_init(struct pci_controller *hose)
+{
+	unsigned short temp_short;
+
+	/*--------------------------------------------------------------------------+
+	  | Write the PowerPC440 EP PCI Configuration regs.
+	  |   Enable PowerPC440 EP to be a master on the PCI bus (PMM).
+	  |   Enable PowerPC440 EP to act as a PCI memory target (PTM).
+	  +--------------------------------------------------------------------------*/
+	pci_read_config_word(0, PCI_COMMAND, &temp_short);
+	pci_write_config_word(0, PCI_COMMAND,
+			      temp_short | PCI_COMMAND_MASTER |
+			      PCI_COMMAND_MEMORY);
+}
+#endif
+
+/*************************************************************************
+ *  is_pci_host
+ *
+ *	This routine is called to determine if a pci scan should be
+ *	performed. With various hardware environments (especially cPCI and
+ *	PPMC) it's insufficient to depend on the state of the arbiter enable
+ *	bit in the strap register, or generic host/adapter assumptions.
+ *
+ *	Rather than hard-code a bad assumption in the general 440 code, the
+ *	440 pci code requires the board to decide at runtime.
+ *
+ *	Return 0 for adapter mode, non-zero for host (monarch) mode.
+ *
+ *
+ ************************************************************************/
+#if defined(CONFIG_PCI)
+int is_pci_host(struct pci_controller *hose)
+{
+	/* Korat is always configured as host. */
+	return (1);
+}
+#endif
+
+#if defined(CONFIG_POST)
+/*
+ * Returns 1 if keys pressed to start the power-on long-running tests
+ * Called from board_init_f().
+ */
+int post_hotkeys_pressed(void)
+{
+	return 0;		/* No hotkeys supported */
+}
+#endif
diff --git a/board/korat/u-boot.lds b/board/korat/u-boot.lds
new file mode 100644
index 0000000..a423f98
--- /dev/null
+++ b/board/korat/u-boot.lds
@@ -0,0 +1,145 @@
+/*
+ * (C) Copyright 2002
+ * Wolfgang Denk, DENX Software Engineering, wd at denx.de.
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+OUTPUT_ARCH(powerpc)
+SEARCH_DIR(/lib); SEARCH_DIR(/usr/lib); SEARCH_DIR(/usr/local/lib); SEARCH_DIR(/usr/local/powerpc-any-elf/lib);
+/* Do we need any of these for elf?
+   __DYNAMIC = 0;    */
+SECTIONS
+{
+  .resetvec 0xFFFFFFFC :
+  {
+    *(.resetvec)
+  } = 0xffff
+
+  .bootpg 0xFFFFF000 :
+  {
+    cpu/ppc4xx/start.o	(.bootpg)
+  } = 0xffff
+
+  /* Read-only sections, merged into text segment: */
+  . = + SIZEOF_HEADERS;
+  .interp : { *(.interp) }
+  .hash          : { *(.hash)		}
+  .dynsym        : { *(.dynsym)		}
+  .dynstr        : { *(.dynstr)		}
+  .rel.text      : { *(.rel.text)		}
+  .rela.text     : { *(.rela.text) 	}
+  .rel.data      : { *(.rel.data)		}
+  .rela.data     : { *(.rela.data) 	}
+  .rel.rodata    : { *(.rel.rodata) 	}
+  .rela.rodata   : { *(.rela.rodata) 	}
+  .rel.got       : { *(.rel.got)		}
+  .rela.got      : { *(.rela.got)		}
+  .rel.ctors     : { *(.rel.ctors)	}
+  .rela.ctors    : { *(.rela.ctors)	}
+  .rel.dtors     : { *(.rel.dtors)	}
+  .rela.dtors    : { *(.rela.dtors)	}
+  .rel.bss       : { *(.rel.bss)		}
+  .rela.bss      : { *(.rela.bss)		}
+  .rel.plt       : { *(.rel.plt)		}
+  .rela.plt      : { *(.rela.plt)		}
+  .init          : { *(.init)	}
+  .plt : { *(.plt) }
+  .text      :
+  {
+    /* WARNING - the following is hand-optimized to fit within	*/
+    /* the sector layout of our flash chips!	XXX FIXME XXX	*/
+
+    cpu/ppc4xx/start.o	(.text)
+
+    *(.text)
+    *(.fixup)
+    *(.got1)
+  }
+  _etext = .;
+  PROVIDE (etext = .);
+  .rodata    :
+  {
+    *(.rodata)
+    *(.rodata1)
+    *(.rodata.str1.4)
+  }
+  .fini      : { *(.fini)    } =0
+  .ctors     : { *(.ctors)   }
+  .dtors     : { *(.dtors)   }
+
+  /* Read-write section, merged into data segment: */
+  . = (. + 0x00FF) & 0xFFFFFF00;
+  _erotext = .;
+  PROVIDE (erotext = .);
+  .reloc   :
+  {
+    *(.got)
+    _GOT2_TABLE_ = .;
+    *(.got2)
+    _FIXUP_TABLE_ = .;
+    *(.fixup)
+  }
+  __got2_entries = (_FIXUP_TABLE_ - _GOT2_TABLE_) >>2;
+  __fixup_entries = (. - _FIXUP_TABLE_)>>2;
+
+  .data    :
+  {
+    *(.data)
+    *(.data1)
+    *(.sdata)
+    *(.sdata2)
+    *(.dynamic)
+    CONSTRUCTORS
+  }
+  _edata  =  .;
+  PROVIDE (edata = .);
+
+  . = .;
+  __u_boot_cmd_start = .;
+  .u_boot_cmd : { *(.u_boot_cmd) }
+  __u_boot_cmd_end = .;
+
+
+  . = .;
+  __start___ex_table = .;
+  __ex_table : { *(__ex_table) }
+  __stop___ex_table = .;
+
+  . = ALIGN(256);
+  __init_begin = .;
+  .text.init : { *(.text.init) }
+  .data.init : { *(.data.init) }
+  . = ALIGN(256);
+  __init_end = .;
+
+  __bss_start = .;
+  .bss       :
+  {
+   *(.sbss) *(.scommon)
+   *(.dynbss)
+   *(.bss)
+   *(COMMON)
+  }
+
+  ppcenv_assert = ASSERT(. < 0xFFFF8000, ".bss section too big, overlaps .ppcenv section. Please update your confguration: CFG_MONITOR_BASE, CFG_MONITOR_LEN and TEXT_BASE may need to be modified.");
+
+  _end = . ;
+  PROVIDE (end = .);
+}
-- 
1.5.2.5






More information about the U-Boot mailing list