[U-Boot-Users] [PATCH 20/25] include/configs: Use new CONFIG_CMD_* in various o* named board config files.
Jon Loeliger
jdl at jdl.com
Thu Jul 5 05:33:13 CEST 2007
Signed-off-by: Jon Loeliger <jdl at freescale.com>
---
include/configs/o2dnt.h | 36 +++++++++++++++---------------
include/configs/ocotea.h | 49 +++++++++++++++++++++-------------------
include/configs/omap1510inn.h | 16 ++++++++++---
include/configs/omap1610h2.h | 14 ++++++++---
include/configs/omap1610inn.h | 14 ++++++++---
include/configs/omap2420h4.h | 22 ++++++++++++++----
include/configs/omap5912osk.h | 14 ++++++++---
include/configs/omap730p2.h | 13 ++++++----
8 files changed, 111 insertions(+), 67 deletions(-)
diff --git a/include/configs/o2dnt.h b/include/configs/o2dnt.h
index 63d0da7..9ed1ed8 100644
--- a/include/configs/o2dnt.h
+++ b/include/configs/o2dnt.h
@@ -37,11 +37,6 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
-# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
-#endif
-
/*
* Serial console configuration
*/
@@ -82,20 +77,20 @@
#define CONFIG_TIMESTAMP /* Print image info with timestamp */
+
/*
- * Supported commands
+ * Command line configuration.
*/
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_EEPROM | \
- CFG_CMD_FAT | \
- CFG_CMD_I2C | \
- CFG_CMD_NFS | \
- CFG_CMD_MII | \
- CFG_CMD_PING | \
- ADD_PCI_CMD )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+#define CONFIG_PCI_CMD
+
#if (TEXT_BASE == 0xFF000000) /* Boot low with 16 MB Flash */
# define CFG_LOWBOOT 1
@@ -246,7 +241,7 @@
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -262,6 +257,11 @@
#define CFG_HZ 1000 /* decrementer freq: 1 ms ticks */
+#define CFG_CACHELINE_SIZE 32 /* For MPC5xxx CPUs */
+#if defined(CONFIG_CMD_KGDB)
+# define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
+#endif
+
/*
* Various low-level settings
*/
diff --git a/include/configs/ocotea.h b/include/configs/ocotea.h
index 68e8cec..fd45c1d 100644
--- a/include/configs/ocotea.h
+++ b/include/configs/ocotea.h
@@ -232,26 +232,29 @@
#define CONFIG_NETCONSOLE /* include NetConsole support */
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | \
- CFG_CMD_ASKENV | \
- CFG_CMD_DATE | \
- CFG_CMD_DHCP | \
- CFG_CMD_DIAG | \
- CFG_CMD_ELF | \
- CFG_CMD_EEPROM | \
- CFG_CMD_I2C | \
- CFG_CMD_IRQ | \
- CFG_CMD_MII | \
- CFG_CMD_NET | \
- CFG_CMD_NFS | \
- CFG_CMD_PCI | \
- CFG_CMD_PING | \
- CFG_CMD_REGINFO | \
- CFG_CMD_SDRAM | \
- CFG_CMD_SNTP )
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_SNTP
+
#undef CONFIG_WATCHDOG /* watchdog disabled */
@@ -260,7 +263,7 @@
*/
#define CFG_LONGHELP /* undef to save memory */
#define CFG_PROMPT "=> " /* Monitor Command Prompt */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CBSIZE 1024 /* Console I/O Buffer Size */
#else
#define CFG_CBSIZE 256 /* Console I/O Buffer Size */
@@ -310,7 +313,7 @@
*/
#define CFG_DCACHE_SIZE 32768 /* For AMCC 440 CPUs */
#define CFG_CACHELINE_SIZE 32 /* ... */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CFG_CACHELINE_SHIFT 5 /* log base 2 of the above value */
#endif
@@ -322,7 +325,7 @@
#define BOOTFLAG_COLD 0x01 /* Normal Power-On: Boot from FLASH */
#define BOOTFLAG_WARM 0x02 /* Software reboot */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 2 /* which serial port to use */
#endif
diff --git a/include/configs/omap1510inn.h b/include/configs/omap1510inn.h
index 016d3d8..11fdb47 100644
--- a/include/configs/omap1510inn.h
+++ b/include/configs/omap1510inn.h
@@ -86,11 +86,19 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
+#define CONFIG_COMMANDS (CONFIG_CMD_DFL
+
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
@@ -98,7 +106,7 @@
#define CONFIG_BOOTCOMMAND "bootp;tftp;bootm"
#define CFG_AUTOLOAD "n" /* No autoload */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
/* what's this ? it's not used anywhere */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
diff --git a/include/configs/omap1610h2.h b/include/configs/omap1610h2.h
index c6ca689..d78f79f 100644
--- a/include/configs/omap1610h2.h
+++ b/include/configs/omap1610h2.h
@@ -81,11 +81,17 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
@@ -93,7 +99,7 @@
#define CONFIG_BOOTCOMMAND "bootp;tftp;bootm"
#define CFG_AUTOLOAD "n" /* No autoload */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
diff --git a/include/configs/omap1610inn.h b/include/configs/omap1610inn.h
index f28ede0..7d0658f 100644
--- a/include/configs/omap1610inn.h
+++ b/include/configs/omap1610inn.h
@@ -82,11 +82,17 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
@@ -98,7 +104,7 @@
#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */
#define CONFIG_BOOTFILE "uImage" /* file to load */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
diff --git a/include/configs/omap2420h4.h b/include/configs/omap2420h4.h
index 5837461..46e0dcc 100644
--- a/include/configs/omap2420h4.h
+++ b/include/configs/omap2420h4.h
@@ -119,15 +119,27 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE {9600, 19200, 38400, 57600, 115200}
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
#ifdef CFG_NAND_BOOT
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_NAND | CFG_CMD_JFFS2)
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_NAND
+ #define CONFIG_CMD_JFFS2
#else
-#define CONFIG_COMMANDS ((CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_I2C | CFG_CMD_JFFS2) & ~CFG_CMD_AUTOSCRIPT)
+ #define CONFIG_CMD_DHCP
+ #define CONFIG_CMD_I2C
+ #define CONFIG_CMD_JFFS2
+
+ #undef CONFIG_CMD_AUTOSCRIPT
#endif
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
/*
* Board NAND Info.
diff --git a/include/configs/omap5912osk.h b/include/configs/omap5912osk.h
index 5db4f52..296b6bc 100644
--- a/include/configs/omap5912osk.h
+++ b/include/configs/omap5912osk.h
@@ -86,11 +86,17 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
#include <configs/omap1510.h>
#define CONFIG_BOOTDELAY 3
@@ -102,7 +108,7 @@
#define CONFIG_SERVERIP 156.117.97.139 /* current IP of my dev pc */
#define CONFIG_BOOTFILE "uImage" /* file to load */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* which serial port to use */
#endif
diff --git a/include/configs/omap730p2.h b/include/configs/omap730p2.h
index fda55cf..af9877f 100644
--- a/include/configs/omap730p2.h
+++ b/include/configs/omap730p2.h
@@ -90,14 +90,17 @@
#define CONFIG_BAUDRATE 115200
#define CFG_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, 115200 }
-#define CONFIG_COMMANDS (CONFIG_CMD_DFL | CFG_CMD_DHCP)
-#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
/*
- * This must be included AFTER the definition of CONFIG_COMMANDS (if any)
+ * Command line configuration.
*/
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+
+
+#define CONFIG_BOOTP_MASK CONFIG_BOOTP_DEFAULT
-#include <cmd_confdefs.h>
#include <configs/omap730.h>
#include <configs/h2_p2_dbg_board.h>
@@ -112,7 +115,7 @@
#define CONFIG_SERVERIP 192.150.0.100
#define CONFIG_BOOTFILE "uImage" /* File to load */
-#if defined (CONFIG_COMMANDS) && defined (CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
#define CONFIG_KGDB_BAUDRATE 115200 /* Speed to run kgdb serial port */
#define CONFIG_KGDB_SER_INDEX 1 /* Which serial port to use */
#endif
--
1.5.2.2.249.g45fd
More information about the U-Boot
mailing list