[U-Boot-Users] [PATCH 21/25] include/configs: Use new CONFIG_CMD_* in various p* named board config files.

Jon Loeliger jdl at jdl.com
Thu Jul 5 05:33:17 CEST 2007 

Signed-off-by: Jon Loeliger <jdl at freescale.com>
---
 include/configs/p3mx.h       |   43 +++++++++++++++++++-----------------
 include/configs/p3p440.h     |   47 +++++++++++++++++++++------------------
 include/configs/pb1x00.h     |   31 ++++++++++++++++++-------
 include/configs/pcs440ep.h   |   49 +++++++++++++++++++++--------------------
 include/configs/pcu_e.h      |   26 +++++++++++-----------
 include/configs/pdnb3.h      |   33 +++++++++++++--------------
 include/configs/pleb2.h      |   12 ++++++---
 include/configs/ppmc7xx.h    |   45 ++++++++++++++++++++------------------
 include/configs/ppmc8260.h   |   29 +++++++++++++-----------
 include/configs/purple.h     |   10 ++++++-
 include/configs/pxa255_idp.h |   14 ++++++++---
 11 files changed, 190 insertions(+), 149 deletions(-)

diff --git a/include/configs/p3mx.h b/include/configs/p3mx.h
index 54462f0..6994f7b 100644
--- a/include/configs/p3mx.h
+++ b/include/configs/p3mx.h
@@ -253,24 +253,27 @@
 #define CONFIG_BOOTDELAY	3	/* autoboot after 5 seconds */
 #define CONFIG_BOOTP_MASK	(CONFIG_BOOTP_DEFAULT | \
 				 CONFIG_BOOTP_BOOTFILESIZE)
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_CACHE   | \
-				CFG_CMD_SDRAM)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_CACHE
+#define CONFIG_CMD_SDRAM
+
 
 /*-----------------------------------------------------------------------
  * Miscellaneous configurable options
@@ -280,7 +283,7 @@
 
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
@@ -421,7 +424,7 @@
  * Cache Configuration
  */
 #define CFG_CACHELINE_SIZE	32	/* For all MPC74xx CPUs		 */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
diff --git a/include/configs/p3p440.h b/include/configs/p3p440.h
index 22f9f84..2a42961 100644
--- a/include/configs/p3p440.h
+++ b/include/configs/p3p440.h
@@ -168,25 +168,28 @@
 
 #define CONFIG_NETCONSOLE		/* include NetConsole support	*/
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_SNTP	)
-
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_SNTP
+
 
 #undef CONFIG_WATCHDOG			/* watchdog disabled		*/
 
@@ -195,7 +198,7 @@
  *----------------------------------------------------------------------*/
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
@@ -304,7 +307,7 @@
  */
 #define CFG_DCACHE_SIZE		(32<<10)	/* For AMCC 405 CPUs		*/
 #define CFG_CACHELINE_SIZE	32	/* ...					*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 
@@ -316,7 +319,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/pb1x00.h b/include/configs/pb1x00.h
index ed1893f..c84795b 100644
--- a/include/configs/pb1x00.h
+++ b/include/configs/pb1x00.h
@@ -132,11 +132,8 @@
 /*---USB -------------------------------------------*/
 #if 0
 #define CONFIG_USB_OHCI
-#define ADD_USB_CMD             CFG_CMD_USB | CFG_CMD_FAT
 #define CONFIG_USB_STORAGE
 #define CONFIG_DOS_PARTITION
-#else
-#define ADD_USB_CMD             0
 #endif
 
 /*---ATA PCMCIA ------------------------------------*/
@@ -179,11 +176,27 @@
 #define CFG_ICACHE_SIZE		16384
 #define CFG_CACHELINE_SIZE	32
 
-#define CONFIG_COMMANDS	\
-  (((CONFIG_CMD_DFL | CFG_CMD_DHCP | CFG_CMD_ELF | CFG_CMD_MII | CFG_CMD_PING) & \
- ~(CFG_CMD_ENV | CFG_CMD_FAT | CFG_CMD_FLASH | CFG_CMD_FPGA | CFG_CMD_IDE | \
-   CFG_CMD_LOADS | CFG_CMD_RUN | CFG_CMD_LOADB | CFG_CMD_ELF | \
-   CFG_CMD_BDI | CFG_CMD_BEDBUG)) | ADD_USB_CMD)
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_PING
+
+#undef CONFIG_CMD_ENV
+#undef CONFIG_CMD_FAT
+#undef CONFIG_CMD_FLASH
+#undef CONFIG_CMD_FPGA
+#undef CONFIG_CMD_IDE
+#undef CONFIG_CMD_LOADS
+#undef CONFIG_CMD_RUN
+#undef CONFIG_CMD_LOADB
+#undef CONFIG_CMD_ELF
+#undef CONFIG_CMD_BDI
+#undef CONFIG_CMD_BEDBUG
 
 #endif	/* __CONFIG_H */
diff --git a/include/configs/pcs440ep.h b/include/configs/pcs440ep.h
index 751b512..f0cd8d3 100644
--- a/include/configs/pcs440ep.h
+++ b/include/configs/pcs440ep.h
@@ -208,37 +208,38 @@
 #define CONFIG_HW_WATCHDOG			/* watchdog */
 #endif
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DIAG	| \
-				CFG_CMD_EEPROM	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_IRQ	| \
-				CFG_CMD_MII	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_NFS	| \
-				CFG_CMD_PCI	| \
-				CFG_CMD_PING	| \
-				CFG_CMD_REGINFO	| \
-				CFG_CMD_SDRAM	| \
-				CFG_CMD_EXT2	| \
-				CFG_CMD_FAT	| \
-				CFG_CMD_USB	)
 
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DIAG
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_IRQ
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_PCI
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_SDRAM
+#define CONFIG_CMD_EXT2
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_USB
 
-#define CONFIG_SUPPORT_VFAT
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+#define CONFIG_SUPPORT_VFAT
 
 /*
  * Miscellaneous configurable options
  */
 #define CFG_LONGHELP			/* undef to save memory		*/
 #define CFG_PROMPT	        "=> "	/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CBSIZE	        1024	/* Console I/O Buffer Size	*/
 #else
 #define CFG_CBSIZE	        256	/* Console I/O Buffer Size	*/
@@ -393,7 +394,7 @@
  */
 #define CFG_DCACHE_SIZE		(32<<10) /* For AMCC 440 CPUs			*/
 #define CFG_CACHELINE_SIZE	32	/* ...			*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value	*/
 #endif
 
@@ -405,7 +406,7 @@
 #define BOOTFLAG_COLD	0x01		/* Normal Power-On: Boot from FLASH	*/
 #define BOOTFLAG_WARM	0x02		/* Software reboot			*/
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400	/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2	/* which serial port to use */
 #endif
diff --git a/include/configs/pcu_e.h b/include/configs/pcu_e.h
index 73aa3a8..1174e1a 100644
--- a/include/configs/pcu_e.h
+++ b/include/configs/pcu_e.h
@@ -89,28 +89,28 @@
  * ---------------------------------------------------------------- */
 #define CFG_SPI_INIT_OFFSET		0xB00
 
-#define CONFIG_COMMANDS		(	CONFIG_CMD_DFL	| \
-					CFG_CMD_BSP	| \
-					CFG_CMD_DATE	| \
-					CFG_CMD_DHCP	| \
-					CFG_CMD_EEPROM	| \
-					CFG_CMD_NFS	| \
-					CFG_CMD_SNTP	)
 
-#define CONFIG_BOOTP_MASK \
-    ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY)
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+#define CONFIG_CMD_BSP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_EEPROM
+#define CONFIG_CMD_NFS
+#define CONFIG_CMD_SNTP
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
 
-/*----------------------------------------------------------------------*/
+#define CONFIG_BOOTP_MASK \
+    ((CONFIG_BOOTP_DEFAULT | CONFIG_BOOTP_BOOTFILESIZE) & ~CONFIG_BOOTP_GATEWAY)
 
 /*
  * Miscellaneous configurable options
  */
 #define	CFG_LONGHELP			/* undef to save memory		*/
 #define	CFG_PROMPT	"=> "		/* Monitor Command Prompt	*/
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define	CFG_CBSIZE	1024		/* Console I/O Buffer Size	*/
 #else
 #define	CFG_CBSIZE	256		/* Console I/O Buffer Size	*/
diff --git a/include/configs/pdnb3.h b/include/configs/pdnb3.h
index 06c6652..5d6e169 100644
--- a/include/configs/pdnb3.h
+++ b/include/configs/pdnb3.h
@@ -71,25 +71,24 @@
 #define CONFIG_BAUDRATE         115200
 #define CFG_IXP425_CONSOLE	IXP425_UART1   /* we use UART1 for console */
 
-#if defined(CONFIG_SCPU)
-#define CMD_NAND_ADD		0
-#else
-#define CMD_NAND_ADD		CFG_CMD_NAND
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_DATE
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_I2C
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_PING
+
+#if !defined(CONFIG_SCPU)
+#define CONFIG_CMD_NAND
 #endif
 
-#define CONFIG_COMMANDS	       (CONFIG_CMD_DFL	| \
-				CFG_CMD_DHCP	| \
-				CFG_CMD_DATE	| \
-				CFG_CMD_NET	| \
-				CFG_CMD_MII	| \
-				CMD_NAND_ADD	| \
-				CFG_CMD_I2C	| \
-				CFG_CMD_ELF	| \
-				CFG_CMD_PING)
-
-/* This must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-/* These are u-boot generic parameters */
-#include <cmd_confdefs.h>
 
 #define CONFIG_ZERO_BOOTDELAY_CHECK	/* check for keypress on bootdelay==0 */
 #define CONFIG_BOOTDELAY	5	/* autoboot after 5 seconds	*/
diff --git a/include/configs/pleb2.h b/include/configs/pleb2.h
index a6c2371..f581fe5 100644
--- a/include/configs/pleb2.h
+++ b/include/configs/pleb2.h
@@ -66,10 +66,14 @@
 
 #define CONFIG_BAUDRATE		115200
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL & ~CFG_CMD_NET)
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#undef CONFIG_CMD_NET
+
 
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_ETHADDR		08:00:3e:26:0a:5b
@@ -83,7 +87,7 @@
 #define CONFIG_INITRD_TAG
 #define CONFIG_SETUP_MEMORY_TAGS
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	230400		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
 #endif
diff --git a/include/configs/ppmc7xx.h b/include/configs/ppmc7xx.h
index 072b9dd..6a3bd33 100644
--- a/include/configs/ppmc7xx.h
+++ b/include/configs/ppmc7xx.h
@@ -53,29 +53,35 @@
 /*
  * Monitor configuration
  *
- * CONFIG_COMMANDS		- List of command sets to include in shell
+ * List of command sets to include in shell
  *
  * The following command sets have been tested and known to work:
  *
- * CFG_CMD_CACHE		- Cache control commands
- * CFG_CMD_MEMORY		- Memory display, change and test commands
- * CFG_CMD_FLASH		- Erase and program flash
- * CFG_CMD_ENV			- Environment commands
- * CFG_CMD_RUN			- Run commands stored in env vars
- * CFG_CMD_ELF			- Load ELF files
- * CFG_CMD_NET			- Networking/file download commands
- * CFG_CMD_PING			- ICMP Echo Request command
- * CFG_CMD_PCI			- PCI Bus scanning command
+ * CMD_CACHE		- Cache control commands
+ * CMD_MEMORY		- Memory display, change and test commands
+ * CMD_FLASH		- Erase and program flash
+ * CMD_ENV		- Environment commands
+ * CMD_RUN		- Run commands stored in env vars
+ * CMD_ELF		- Load ELF files
+ * CMD_NET		- Networking/file download commands
+ * CMD_PIN		- ICMP Echo Request command
+ * CMD_PCI		- PCI Bus scanning command
  */
 
-#define CONFIG_COMMANDS		( (CFG_CMD_DFL & ~(CFG_CMD_KGDB)) |	\
-						   CFG_CMD_FLASH |	\
-						   CFG_CMD_ENV |	\
-						   CFG_CMD_RUN |	\
-						   CFG_CMD_ELF |	\
-						   CFG_CMD_NET |	\
-						   CFG_CMD_PING |	\
-						   CFG_CMD_PCI)
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_FLASH
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_PCI
+
+#undef CONFIG_CMD_KGDB
 
 
 /*
@@ -149,9 +155,6 @@
  */
 
 
-#include <cmd_confdefs.h>
-
-
 /*
  * Memory map
  *
diff --git a/include/configs/ppmc8260.h b/include/configs/ppmc8260.h
index d671dcc..d99da2f 100644
--- a/include/configs/ppmc8260.h
+++ b/include/configs/ppmc8260.h
@@ -275,14 +275,20 @@
 /* Monitor Command Prompt */
 #define CFG_PROMPT		"=> "
 
-/* What U-Boot subsytems do you want enabled? */
-#define CONFIG_COMMANDS		(((CONFIG_CMD_DFL & ~(CFG_CMD_KGDB))) | \
-				CFG_CMD_ELF	| \
-				CFG_CMD_ASKENV	| \
-				CFG_CMD_REGINFO | \
-				CFG_CMD_MEMTEST | \
-				CFG_CMD_MII	| \
-				CFG_CMD_IMMAP)
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+#define CONFIG_CMD_ASKENV
+#define CONFIG_CMD_REGINFO
+#define CONFIG_CMD_MEMTEST
+#define CONFIG_CMD_MII
+#define CONFIG_CMD_IMMAP
+
+#undef CONFIG_CMD_KGDB
 
 
 /* Where do the internal registers live? */
@@ -298,13 +304,10 @@
 #define CONFIG_PPMC8260		1	/* on an Wind River PPMC8260 Board  */
 #define CONFIG_CPM2		1	/* Has a CPM2 */
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
-
 /*
  * Miscellaneous configurable options
  */
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #  define CFG_CBSIZE		1024	/* Console I/O Buffer Size	     */
 #else
 #  define CFG_CBSIZE		256	/* Console I/O Buffer Size	     */
@@ -477,7 +480,7 @@
  */
 #define CFG_CACHELINE_SIZE	32	/* For MPC8260 CPU */
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 # define CFG_CACHELINE_SHIFT	5	/* log base 2 of the above value */
 #endif
 
diff --git a/include/configs/purple.h b/include/configs/purple.h
index 2ecb7fb..61e18d7 100644
--- a/include/configs/purple.h
+++ b/include/configs/purple.h
@@ -81,8 +81,14 @@
 	""
 #define CONFIG_BOOTCOMMAND	"run flash_self"
 
-#define CONFIG_COMMANDS	(CONFIG_CMD_DFL | CFG_CMD_ELF)
-#include <cmd_confdefs.h>
+
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_ELF
+
 
 #define CFG_SDRAM_BASE		0x80000000
 
diff --git a/include/configs/pxa255_idp.h b/include/configs/pxa255_idp.h
index e5e2772..d7e4e8a 100644
--- a/include/configs/pxa255_idp.h
+++ b/include/configs/pxa255_idp.h
@@ -102,10 +102,16 @@
 
 #define CONFIG_BAUDRATE		115200
 
-#define CONFIG_COMMANDS		(CONFIG_CMD_DFL | CFG_CMD_MMC | CFG_CMD_FAT | CFG_CMD_DHCP )
 
-/* this must be included AFTER the definition of CONFIG_COMMANDS (if any) */
-#include <cmd_confdefs.h>
+/*
+ * Command line configuration.
+ */
+#include <config_cmd_default.h>
+
+#define CONFIG_CMD_MMC
+#define CONFIG_CMD_FAT
+#define CONFIG_CMD_DHCP
+
 
 #define CONFIG_BOOTDELAY	3
 #define CONFIG_BOOTCOMMAND	"bootm 40000"
@@ -192,7 +198,7 @@
 /*			"protect off"	*/
 
 
-#if (CONFIG_COMMANDS & CFG_CMD_KGDB)
+#if defined(CONFIG_CMD_KGDB)
 #define CONFIG_KGDB_BAUDRATE	115200		/* speed to run kgdb serial port */
 #define CONFIG_KGDB_SER_INDEX	2		/* which serial port to use */
 #endif
-- 
1.5.2.2.249.g45fd

More information about the U-Boot mailing list