[U-Boot-Users] [PATCH] sh: Renesas R0P7785LC0011RL board support

Jean-Christophe PLAGNIOL-VILLARD plagnioj at jcrosoft.com
Wed Jul 9 21:28:34 CEST 2008


> +include $(TOPDIR)/config.mk
> +
> +LIB	= lib$(BOARD).a
> +
> +COBJS	:= r0p7785lc0011rl.o selfcheck.o rtl8169_mac.o
> +SOBJS	:= lowlevel_init.o
> +
> +$(LIB):	$(COBJS) $(SOBJS)
> +	$(AR) crv $@ $(COBJS) $(SOBJS)
please use $(ARFLAGS) instead of 'crv'
> +
> +clean:
> +	rm -f $(SOBJS) $(OBJS)
> +
> +distclean:	clean
> +	rm -f $(LIB) core *.bak .depend
pelase add the $(obj)
> +
> +#########################################################################
> +
> +.depend:	Makefile $(SOBJS:.o=.S) $(OBJS:.o=.c)
> +		$(CC) -M $(CPPFLAGS) $(SOBJS:.o=.S) $(OBJS:.o=.c) > $@
> +
> +-include .depend
> +
> + * MA 02111-1307 USA
> + */
> +
> +#define PCIREG_8(_adr)	(*(volatile unsigned char *)(_adr))
> +#define PCIREG_32(_adr)	(*(volatile unsigned long *)(_adr))
> +#define PCI_PAR		PCIREG_32(0xfe0401c0)
> +#define PCI_PDR		PCIREG_32(0xfe040220)
> +#define PCI_CR		PCIREG_32(0xfe040100)
> +#define PCI_CONF1	PCIREG_32(0xfe040004)
> +
> +#define EEPROM_ADD      0x00000050
> +#define HIGH		1
> +#define LOW		0
> +
> +#define PCI_PROG	0x80
> +
> +#define PCI_EEP_ADDRESS		(unsigned short)0x0007
> +#define PCI_MAC_ADDRESS_SIZE	3
> +
> +#define TIME1	100
> +#define TIME2	20000

> +#define BIT_DUMMY	0
> +#define MAC_EEP_READ	1
> +#define MAC_EEP_WRITE	2
> +#define MAC_EEP_ERACE	3
> +#define MAC_EEP_EWEN	4
> +#define MAC_EEP_EWDS	5
> +
> +#define DEBUG 0
Please remove
Could you add few comment about the data?
> +
> +/* RTL8169 */
> +const unsigned short EEPROM_W_Data_8169_A[] = {
> +	0x8129, 0x10ec, 0x8169, 0x1154, 0x032b,
> +	0x4020, 0xa101
> +};
> +const unsigned short EEPROM_W_Data_8169_B[] = {
> +	0x4d15, 0xf7c2, 0x8000, 0x0000, 0x0000, 0x1300,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x2000,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000,
> +	0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000, 0x0000
> +};
> +

> +
> +int do_set_mac(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
> +{
> +	int i;
> +	unsigned char mac[6];
> +	char *s, *e;
> +
> +	if (argc != 2) {
> +		printf("Usage:\n%s\n", cmdtp->usage);
> +		return 1;
> +	}
> +
> +	s = argv[1];
> +
> +	for (i = 0; i < 6; i++) {
> +		mac[i] = s ? simple_strtoul(s, &e, 16) : 0;
> +		if (s)
> +			s = (*e) ? e + 1 : e;
> +	}
> +	mac_write(mac);
> +
> +	return 0;
> +}
> +
> +U_BOOT_CMD(
> +	setmac,	2,	1,	do_set_mac,
> +	"setmac - write MAC address for RTL8110SCL\n",
> +	"\n"
> +	"setmac <mac address> - write MAC address for RTL8110SCL\n"
> +);
> +
> +int do_print_mac(cmd_tbl_t *cmdtp, int flag, int argc, char *argv[])
> +{
> +	int i;
> +	uchar mac[6];
> +
> +	if (argc != 1) {
> +		printf("Usage:\n%s\n", cmdtp->usage);
> +		return 1;
> +	}
> +
> +	mac_read();
> +
> +	return 0;
> +}
> +
> +U_BOOT_CMD(
> +	printmac,	1,	1,	do_print_mac,
> +	"printmac - print MAC address for RTL8110\n",
> +	"\n"
> +	"    - print MAC address for RTL8110\n"
> +);
Could you add a README for this board and describe its specific command?
> +
> +
> +U_BOOT_CMD(
> +	hwtest,	2,	1,	do_hw_test,
> +	"hwtest - hardware test for R0P7785LC0011RL board\n",
> +	"\n"
> +	"hwtest all   - test all hardware\n"
> +	"hwtest pld   - output pld version\n"
> +	"hwtest led   - test LED\n"
> +	"hwtest dipsw - test DIPSW\n"
> +	"hwtest sm107 - output SM107 version\n"
> +	"hwtest usb   - test R8A66597\n"
> +	"hwtest i2c   - output PCA9564 version\n"
> +	"hwtest net   - compare RTL8110 ID\n"
> +	"hwtest sata  - compare SiI3512 ID\n"
> +	"hwtest pci   - output PCI slot device ID\n"
> +);
idem
> +
 +
> +#define CONFIG_NETMASK		255.255.255.0
> +#define CONFIG_IPADDR		192.168.10.100
> +#define CONFIG_SERVERIP		192.168.10.77
> +#define CONFIG_GATEWAYIP	192.168.10.77
please remove this 4 defines
> +
> +#define __io
> +#define __mem_pci
is it really the good place to define it??
> +
> +#define CONFIG_PCI_MEM_BUS	0xFD000000	/* Memory space base addr */
> +#define CONFIG_PCI_MEM_PHYS	CONFIG_PCI_MEM_BUS
> +#define CONFIG_PCI_MEM_SIZE	0x01000000	/* Size of Memory window */
> +

Best Regards,
J.




More information about the U-Boot mailing list