[U-Boot] [PATCH] powerpc: change 86xx SMP boot method
Becky Bruce
becky.bruce at freescale.com
Sat Nov 1 04:38:39 CET 2008
FYI,
This is dependent on the previous set of patches I sent to the list
earlier this evening, which aren't numbered, because they were all
independent.... It also needs testing on sbc8641d - I don't have a
board.
Cheers,
Becky
On Oct 31, 2008, at 10:33 PM, Becky Bruce wrote:
> We put the bootpg for the secondary cpus into memory and use
> BPTR to get to it. This is a step towards converting to the
> ePAPR boot methodology. Also, the code is written to
> deal properly with more than 4GB of RAM.
>
> Signed-off-by: Becky Bruce <becky.bruce at freescale.com>
> ---
> cpu/mpc86xx/Makefile | 4 +
> cpu/mpc86xx/cpu_init.c | 4 +
> cpu/mpc86xx/fdt.c | 21 +++++
> cpu/mpc86xx/mp.c | 68 ++++++++++++++++
> cpu/mpc86xx/mp.h | 7 ++
> cpu/mpc86xx/release.S | 169 ++++++++++++++++++++++++++++++++
> +++++++++
> cpu/mpc86xx/start.S | 77 +------------------
> include/configs/MPC8610HPCD.h | 7 ++
> include/configs/MPC8641HPCN.h | 7 ++
> include/configs/sbc8641d.h | 7 ++
> 10 files changed, 298 insertions(+), 73 deletions(-)
> create mode 100644 cpu/mpc86xx/mp.c
> create mode 100644 cpu/mpc86xx/mp.h
> create mode 100644 cpu/mpc86xx/release.S
>
> diff --git a/cpu/mpc86xx/Makefile b/cpu/mpc86xx/Makefile
> index a9767ad..34a9755 100644
> --- a/cpu/mpc86xx/Makefile
> +++ b/cpu/mpc86xx/Makefile
> @@ -31,6 +31,10 @@ LIB = $(obj)lib$(CPU).a
> START = start.o
> SOBJS = cache.o
>
> +ifneq ($(CONFIG_NUM_CPUS),1)
> +COBJS-y += mp.o
> +SOBJS += release.o
> +endif
> COBJS-y += traps.o
> COBJS-y += cpu.o
> COBJS-y += cpu_init.o
> diff --git a/cpu/mpc86xx/cpu_init.c b/cpu/mpc86xx/cpu_init.c
> index 4ab88f0..06f179c 100644
> --- a/cpu/mpc86xx/cpu_init.c
> +++ b/cpu/mpc86xx/cpu_init.c
> @@ -31,6 +31,7 @@
> #include <mpc86xx.h>
> #include <asm/mmu.h>
> #include <asm/fsl_law.h>
> +#include "mp.h"
>
> DECLARE_GLOBAL_DATA_PTR;
>
> @@ -121,6 +122,9 @@ void cpu_init_f(void)
> */
> int cpu_init_r(void)
> {
> +#if (CONFIG_NUM_CPUS > 1)
> + setup_mp();
> +#endif
> return 0;
> }
>
> diff --git a/cpu/mpc86xx/fdt.c b/cpu/mpc86xx/fdt.c
> index 1fef94f..3adfad9 100644
> --- a/cpu/mpc86xx/fdt.c
> +++ b/cpu/mpc86xx/fdt.c
> @@ -9,9 +9,17 @@
> #include <common.h>
> #include <libfdt.h>
> #include <fdt_support.h>
> +#include "mp.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
>
> void ft_cpu_setup(void *blob, bd_t *bd)
> {
> +#if (CONFIG_NUM_CPUS > 1)
> + int off;
> + u32 bootpg;
> +#endif
> +
> do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
> "timebase-frequency", bd->bi_busfreq / 4, 1);
> do_fixup_by_prop_u32(blob, "device_type", "cpu", 4,
> @@ -32,4 +40,17 @@ void ft_cpu_setup(void *blob, bd_t *bd)
> do_fixup_by_compat_u32(blob, "ns16550",
> "clock-frequency", CONFIG_SYS_NS16550_CLK, 1);
> #endif
> +
> +#if (CONFIG_NUM_CPUS > 1)
> + /* if we have 4G or more of memory, put the boot page at 4Gb-1M */
> + if (gd->ram_size > 0xfffff000)
> + bootpg = 0xfff00000;
> + else
> + bootpg = gd->ram_size - (1024 * 1024);
> +
> + /* Reserve the boot page so OSes dont use it */
> + off = fdt_add_mem_rsv(blob, bootpg, (u64)4096);
> + if (off < 0)
> + printf("%s: %s\n", __FUNCTION__, fdt_strerror(off));
> +#endif
> }
> diff --git a/cpu/mpc86xx/mp.c b/cpu/mpc86xx/mp.c
> new file mode 100644
> index 0000000..2940580
> --- /dev/null
> +++ b/cpu/mpc86xx/mp.c
> @@ -0,0 +1,68 @@
> +#include <common.h>
> +#include <asm/processor.h>
> +#include <asm/mmu.h>
> +#include <ioports.h>
> +#include <lmb.h>
> +#include <asm/io.h>
> +#include "mp.h"
> +
> +DECLARE_GLOBAL_DATA_PTR;
> +
> +#if (CONFIG_NUM_CPUS > 1)
> +void cpu_mp_lmb_reserve(struct lmb *lmb)
> +{
> + u32 bootpg;
> +
> + /* if we have 4G or more of memory, put the boot page at 4Gb-1M */
> + if ((u64)gd->ram_size > 0xfffff000)
> + bootpg = 0xfff00000;
> + else
> + bootpg = gd->ram_size - (1024 * 1024);
> +
> + /* tell u-boot we stole a page */
> + lmb_reserve(lmb, bootpg, 4096);
> +}
> +
> +/*
> + * Copy the code for other cpus to execute into an
> + * aligned location accessible via BPTR
> + */
> +void setup_mp(void)
> +{
> + extern ulong __secondary_start_page;
> + ulong fixup = (ulong)&__secondary_start_page;
> + u32 bootpg;
> + u32 bootpg_va;
> +
> + /*
> + * If we have 4G or more of memory, put the boot page at 4Gb-1M.
> + * Otherwise, put it at the very end of RAM.
> + */
> + if (gd->ram_size > 0xfffff000)
> + bootpg = 0xfff00000;
> + else
> + bootpg = gd->ram_size - (1024 * 1024);
> +
> + if (bootpg > CONFIG_SYS_MAX_DDR_BAT_SIZE) {
> + /* We're not covered by the DDR mapping, set up BAT */
> + write_bat(DBAT7, CONFIG_SYS_SCRATCH_VA | BATU_BL_128K |
> + BATU_VS | BATU_VP,
> + bootpg | BATL_PP_RW | BATL_MEMCOHERENCE);
> + bootpg_va = CONFIG_SYS_SCRATCH_VA;
> + } else {
> + bootpg_va = bootpg;
> + }
> +
> + memcpy((void *)bootpg_va, (void *)fixup, 4096);
> + flush_cache(bootpg_va, 4096);
> +
> + /* remove the temporary BAT mapping */
> + if (bootpg >= CONFIG_SYS_MAX_DDR_BAT_SIZE)
> + write_bat(DBAT7, 0, 0);
> +
> + /* If the physical location of bootpg is not at fff00000, set BPTR
> */
> + if (bootpg != 0xfff00000)
> + out_be32((uint *)(CONFIG_SYS_CCSRBAR + 0x20), 0x80000000 |
> + (bootpg >> 12));
> +}
> +#endif
> diff --git a/cpu/mpc86xx/mp.h b/cpu/mpc86xx/mp.h
> new file mode 100644
> index 0000000..886e0c8
> --- /dev/null
> +++ b/cpu/mpc86xx/mp.h
> @@ -0,0 +1,7 @@
> +#ifndef __MPC86XX_MP_H_
> +#define __MPC86XX_MP_H_
> +
> +void setup_mp(void);
> +void cpu_mp_lmb_reserve(struct lmb *lmb);
> +
> +#endif
> diff --git a/cpu/mpc86xx/release.S b/cpu/mpc86xx/release.S
> new file mode 100644
> index 0000000..b524e50
> --- /dev/null
> +++ b/cpu/mpc86xx/release.S
> @@ -0,0 +1,169 @@
> +/*
> + * Copyright 2004, 2007, 2008 Freescale Semiconductor.
> + * Srikanth Srinivasan <srikanth.srinivaan at freescale.com>
> + *
> + * See file CREDITS for list of people who contributed to this
> + * project.
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of
> + * the License, or (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * You should have received a copy of the GNU General Public License
> + * along with this program; if not, write to the Free Software
> + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> + * MA 02111-1307 USA
> + */
> +#include <config.h>
> +#include <mpc86xx.h>
> +#include <version.h>
> +
> +#include <ppc_asm.tmpl>
> +#include <ppc_defs.h>
> +
> +#include <asm/cache.h>
> +#include <asm/mmu.h>
> +
> +/* If this is a multi-cpu system then we need to handle the
> + * 2nd cpu. The assumption is that the 2nd cpu is being
> + * held in boot holdoff mode until the 1st cpu unlocks it
> + * from Linux. We'll do some basic cpu init and then pass
> + * it to the Linux Reset Vector.
> + * Sri: Much of this initialization is not required. Linux
> + * rewrites the bats, and the sprs and also enables the L1 cache.
> + *
> + * Core 0 must copy this to a 1M aligned region and set BPTR
> + * to point to it.
> + */
> +#if (CONFIG_NUM_CPUS > 1)
> + .align 12
> +.globl __secondary_start_page
> +__secondary_start_page:
> + .space 0x100 /* space over to reset vector loc */
> + mfspr r0, MSSCR0
> + andi. r0, r0, 0x0020
> + rlwinm r0,r0,27,31,31
> + mtspr PIR, r0
> +
> + /* Invalidate BATs */
> + li r0, 0
> + mtspr IBAT0U, r0
> + mtspr IBAT1U, r0
> + mtspr IBAT2U, r0
> + mtspr IBAT3U, r0
> + mtspr IBAT4U, r0
> + mtspr IBAT5U, r0
> + mtspr IBAT6U, r0
> + mtspr IBAT7U, r0
> + isync
> + mtspr DBAT0U, r0
> + mtspr DBAT1U, r0
> + mtspr DBAT2U, r0
> + mtspr DBAT3U, r0
> + mtspr DBAT4U, r0
> + mtspr DBAT5U, r0
> + mtspr DBAT6U, r0
> + mtspr DBAT7U, r0
> + isync
> + sync
> +
> + /* enable extended addressing */
> + mfspr r0, HID0
> + lis r0, (HID0_HIGH_BAT_EN | HID0_XBSEN | HID0_XAEN)@h
> + ori r0, r0, (HID0_HIGH_BAT_EN | HID0_XBSEN | HID0_XAEN)@l
> + mtspr HID0, r0
> + sync
> + isync
> +
> +#ifdef CONFIG_SYS_L2
> + /* init the L2 cache */
> + addis r3, r0, L2_INIT at h
> + ori r3, r3, L2_INIT at l
> + sync
> + mtspr l2cr, r3
> +#ifdef CONFIG_ALTIVEC
> + dssall
> +#endif
> + /* invalidate the L2 cache */
> + mfspr r3, l2cr
> + rlwinm. r3, r3, 0, 0, 0
> + beq 1f
> +
> + mfspr r3, l2cr
> + rlwinm r3, r3, 0, 1, 31
> +
> +#ifdef CONFIG_ALTIVEC
> + dssall
> +#endif
> + sync
> + mtspr l2cr, r3
> + sync
> +1: mfspr r3, l2cr
> + oris r3, r3, L2CR_L2I at h
> + mtspr l2cr, r3
> +
> +invl2:
> + mfspr r3, l2cr
> + andis. r3, r3, L2CR_L2I at h
> + bne invl2
> + sync
> +#endif
> +
> + /* enable and invalidate the data cache */
> + mfspr r3, HID0
> + li r5, HID0_DCFI|HID0_DLOCK
> + andc r3, r3, r5
> + mtspr HID0, r3 /* no invalidate, unlock */
> + ori r3, r3, HID0_DCE
> + ori r5, r3, HID0_DCFI
> + mtspr HID0, r5 /* enable + invalidate */
> + mtspr HID0, r3 /* enable */
> + sync
> +#ifdef CFG_L2
> + sync
> + lis r3, L2_ENABLE at h
> + ori r3, r3, L2_ENABLE at l
> + mtspr l2cr, r3
> + isync
> + sync
> +#endif
> +
> + /* enable and invalidate the instruction cache*/
> + mfspr r3, HID0
> + li r5, HID0_ICFI|HID0_ILOCK
> + andc r3, r3, r5
> + ori r3, r3, HID0_ICE
> + ori r5, r3, HID0_ICFI
> + mtspr HID0, r5
> + mtspr HID0, r3
> + isync
> + sync
> +
> + /* TBEN in HID0 */
> + mfspr r4, HID0
> + oris r4, r4, 0x0400
> + mtspr HID0, r4
> + sync
> + isync
> +
> + /* MCP|SYNCBE|ABE in HID1 */
> + mfspr r4, HID1
> + oris r4, r4, 0x8000
> + ori r4, r4, 0x0C00
> + mtspr HID1, r4
> + sync
> + isync
> +
> + lis r3, CONFIG_LINUX_RESET_VEC at h
> + ori r3, r3, CONFIG_LINUX_RESET_VEC at l
> + mtlr r3
> + blr
> +
> + /* Never Returns, Running in Linux Now */
> +#endif
> diff --git a/cpu/mpc86xx/start.S b/cpu/mpc86xx/start.S
> index b1a23b4..48f8c5a 100644
> --- a/cpu/mpc86xx/start.S
> +++ b/cpu/mpc86xx/start.S
> @@ -179,20 +179,10 @@ _end_of_vectors:
>
> boot_cold:
> boot_warm:
> -
> - /* if this is a multi-core system we need to check which cpu
> - * this is, if it is not cpu 0 send the cpu to the linux reset
> - * vector */
> -#if (CONFIG_NUM_CPUS > 1)
> - mfspr r0, MSSCR0
> - andi. r0, r0, 0x0020
> - rlwinm r0,r0,27,31,31
> - mtspr PIR, r0
> - beq 1f
> -
> - bl secondary_cpu_setup
> -#endif
> -
> + /*
> + * NOTE: Only Cpu 0 will ever come here. Other cores go to an
> + * address specified by the BPTR
> + */
> 1:
> #ifdef CONFIG_SYS_RAMBOOT
> /* disable everything */
> @@ -978,63 +968,4 @@ unlock_ram_in_cache:
> #endif
> #endif
>
> -/* If this is a multi-cpu system then we need to handle the
> - * 2nd cpu. The assumption is that the 2nd cpu is being
> - * held in boot holdoff mode until the 1st cpu unlocks it
> - * from Linux. We'll do some basic cpu init and then pass
> - * it to the Linux Reset Vector.
> - * Sri: Much of this initialization is not required. Linux
> - * rewrites the bats, and the sprs and also enables the L1 cache.
> - */
> -#if (CONFIG_NUM_CPUS > 1)
> -.globl secondary_cpu_setup
> -secondary_cpu_setup:
> - /* Do only core setup on all cores except cpu0 */
> - bl invalidate_bats
> - sync
> - bl enable_ext_addr
>
> -#ifdef CONFIG_SYS_L2
> - /* init the L2 cache */
> - addis r3, r0, L2_INIT at h
> - ori r3, r3, L2_INIT at l
> - sync
> - mtspr l2cr, r3
> -#ifdef CONFIG_ALTIVEC
> - dssall
> -#endif
> - /* invalidate the L2 cache */
> - bl l2cache_invalidate
> - sync
> -#endif
> -
> - /* enable and invalidate the data cache */
> - bl dcache_enable
> - sync
> -
> - /* enable and invalidate the instruction cache*/
> - bl icache_enable
> - sync
> -
> - /* TBEN in HID0 */
> - mfspr r4, HID0
> - oris r4, r4, 0x0400
> - mtspr HID0, r4
> - sync
> - isync
> -
> - /* MCP|SYNCBE|ABE in HID1 */
> - mfspr r4, HID1
> - oris r4, r4, 0x8000
> - ori r4, r4, 0x0C00
> - mtspr HID1, r4
> - sync
> - isync
> -
> - lis r3, CONFIG_LINUX_RESET_VEC at h
> - ori r3, r3, CONFIG_LINUX_RESET_VEC at l
> - mtlr r3
> - blr
> -
> - /* Never Returns, Running in Linux Now */
> -#endif
> diff --git a/include/configs/MPC8610HPCD.h b/include/configs/
> MPC8610HPCD.h
> index 67b2764..75aa911 100644
> --- a/include/configs/MPC8610HPCD.h
> +++ b/include/configs/MPC8610HPCD.h
> @@ -36,6 +36,12 @@
>
> #define CONFIG_SYS_RESET_ADDRESS 0xfff00100
>
> +/*
> + * virtual address to be used for temporary mappings. There
> + * should be 128k free at this VA.
> + */
> +#define CONFIG_SYS_SCRATCH_VA 0xc0000000
> +
> #define CONFIG_PCI 1 /* Enable PCI/PCIE*/
> #define CONFIG_PCI1 1 /* PCI controler 1 */
> #define CONFIG_PCIE1 1 /* PCIe 1 connected to ULI bridge */
> @@ -92,6 +98,7 @@
>
> #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
> #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
> +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
> #define CONFIG_VERY_BIG_RAM
>
> #define MPC86xx_DDR_SDRAM_CLK_CNTL
> diff --git a/include/configs/MPC8641HPCN.h b/include/configs/
> MPC8641HPCN.h
> index ad5627f..0dd2156 100644
> --- a/include/configs/MPC8641HPCN.h
> +++ b/include/configs/MPC8641HPCN.h
> @@ -46,6 +46,12 @@
> #define CONFIG_SYS_RESET_ADDRESS 0xfff00100
>
> /*
> + * virtual address to be used for temporary mappings. There
> + * should be 128k free at this VA.
> + */
> +#define CONFIG_SYS_SCRATCH_VA 0xe0000000
> +
> +/*
> * set this to enable Rapid IO. PCI and RIO are mutually exclusive
> */
> /*#define CONFIG_RIO 1*/
> @@ -109,6 +115,7 @@ extern unsigned long get_board_sys_clk(unsigned
> long dummy);
>
> #define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000 /* DDR is system memory*/
> #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
> +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
> #define CONFIG_VERY_BIG_RAM
>
> #define MPC86xx_DDR_SDRAM_CLK_CNTL
> diff --git a/include/configs/sbc8641d.h b/include/configs/sbc8641d.h
> index 09a9901..e8216ea 100644
> --- a/include/configs/sbc8641d.h
> +++ b/include/configs/sbc8641d.h
> @@ -49,6 +49,12 @@
>
> #define CONFIG_SYS_RESET_ADDRESS 0xfff00100
>
> +/*
> + * virtual address to be used for temporary mappings. There
> + * should be 128k free at this VA.
> + */
> +#define CONFIG_SYS_SCRATCH_VA 0xe8000000
> +
> #define CONFIG_PCI 1 /* Enable PCIE */
> #define CONFIG_PCI1 1 /* PCIE controler 1 (slot 1) */
> #define CONFIG_PCI2 1 /* PCIE controler 2 (slot 2) */
> @@ -108,6 +114,7 @@
> #define CONFIG_SYS_DDR_SDRAM_BASE2 0x10000000 /* DDR bank 2 */
> #define CONFIG_SYS_SDRAM_BASE CONFIG_SYS_DDR_SDRAM_BASE
> #define CONFIG_SYS_SDRAM_BASE2 CONFIG_SYS_DDR_SDRAM_BASE2
> +#define CONFIG_SYS_MAX_DDR_BAT_SIZE 0x80000000 /* BAT mapping size */
> #define CONFIG_VERY_BIG_RAM
>
> #define MPC86xx_DDR_SDRAM_CLK_CNTL
> --
> 1.5.5.1
More information about the U-Boot
mailing list