[U-Boot] [PATCH] mpc83xx: fix PCI scan hang on the standaloneMPC837xE-MDS boards

[Liu Dave-R63238]

Hello Anton,

1)
I strongly suggest you use the hardware reset configuration word from
flash,
not from FPGA.
You can set the PCI host and internal arbiter enabled in the HRCW in
flash
to avoid these issue.

2)
Also, I strongly suggest you use the production 837xEMDS pilot rev2.05
board.
Because the early 837xEMDS board is missing PCI bus pull up resistors.

Thanks,
Dave 

> -----Original Message-----
> From: u-boot-bounces at lists.denx.de 
> [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Anton Vorontsov
> Sent: 2008?10?2? 11:18 PM
> To: Phillips Kim-R1AAHA
> Cc: u-boot at lists.denx.de; Kumar Gala
> Subject: [U-Boot] [PATCH] mpc83xx: fix PCI scan hang on the 
> standaloneMPC837xE-MDS boards
> 
> The MPC837xE-MDS board's CPLD can auto-detect if the board is 
> on the PIB,
> standalone or acting as a PCI agent. User's Guide says:
> 
> - When the CPLD recognizes its location on the PIB it automatically
>   configures RCW to the PCI Host.
> - If the CPLD fails to recognize its location then it is automatically
>   configured as an Agent and the PCI is configured to an 
> external arbiter.
> 
> This sounds good. Though in the standalone setup the CPLD 
> sets PCI_HOST
> flag (it's ok, we can't act as PCI agents since we receive CLKIN, not
> PCICLK), but the CPLD doesn't set the ARBITER_ENABLE flag, and without
> any arbiter bad things will happen (here the board hangs 
> during any config
> space reads).
> 
> In this situation we must disable the PCI. And in case of 
> anybody really
> want to use an external arbiter, we provide "pci_external_aribter"
> environment variable.
> 
> Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
> ---
>  board/freescale/mpc837xemds/mpc837xemds.c |   41 
> +++++++++++++++++++++++++++++
>  board/freescale/mpc837xemds/pci.c         |    3 ++
>  include/configs/MPC837XEMDS.h             |    3 ++
>  3 files changed, 47 insertions(+), 0 deletions(-)
> 
> diff --git a/board/freescale/mpc837xemds/mpc837xemds.c 
> b/board/freescale/mpc837xemds/mpc837xemds.c
> index b6b9678..8bc54d1 100644
> --- a/board/freescale/mpc837xemds/mpc837xemds.c
> +++ b/board/freescale/mpc837xemds/mpc837xemds.c
> @@ -270,6 +270,45 @@ int checkboard(void)
>  	return 0;
>  }
>  
> +#ifdef CONFIG_PCI
> +int board_pci_host_broken(void)
> +{
> +	struct immap __iomem *im = (struct immap __iomem *)CFG_IMMR;
> +	const u32 rcw_mask = HRCWH_PCI1_ARBITER_ENABLE | HRCWH_PCI_HOST;
> +	const char *pci_ea = getenv("pci_external_arbiter");
> +
> +	/* It's always OK in case of external arbiter. */
> +	if (pci_ea && !strcmp(pci_ea, "yes"))
> +		return 0;
> +
> +	if ((in_be32(&im->reset.rcwh) & rcw_mask) != rcw_mask)
> +		return 1;
> +
> +	return 0;
> +}
> +
> +static void ft_pci_fixup(void *blob, bd_t *bd)
> +{
> +	const char *status = "broken (no arbiter)";
> +	int off;
> +	int err;
> +
> +	off = fdt_path_offset(blob, "pci0");
> +	if (off < 0) {
> +		printf("WARNING: could not find pci0 alias: %s.\n",
> +			fdt_strerror(off));
> +		return;
> +	}
> +
> +	err = fdt_setprop(blob, off, "status", status, 
> strlen(status) + 1);
> +	if (err) {
> +		printf("WARNING: could not set status for pci0: %s.\n",
> +			fdt_strerror(err));
> +		return;
> +	}
> +}
> +#endif
> +
>  #if defined(CONFIG_OF_BOARD_SETUP)
>  void ft_board_setup(void *blob, bd_t *bd)
>  {
> @@ -277,6 +316,8 @@ void ft_board_setup(void *blob, bd_t *bd)
>  	ft_tsec_fixup(blob, bd);
>  #ifdef CONFIG_PCI
>  	ft_pci_setup(blob, bd);
> +	if (board_pci_host_broken())
> +		ft_pci_fixup(blob, bd);
>  #endif
>  }
>  #endif /* CONFIG_OF_BOARD_SETUP */
> diff --git a/board/freescale/mpc837xemds/pci.c 
> b/board/freescale/mpc837xemds/pci.c
> index ab90979..0eba7df 100644
> --- a/board/freescale/mpc837xemds/pci.c
> +++ b/board/freescale/mpc837xemds/pci.c
> @@ -47,6 +47,9 @@ void pci_init_board(void)
>  	volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
>  	struct pci_region *reg[] = { pci_regions };
>  
> +	if (board_pci_host_broken())
> +		return;
> +
>  	/* Enable all 5 PCI_CLK_OUTPUTS */
>  	clk->occr |= 0xf8000000;
>  	udelay(2000);
> diff --git a/include/configs/MPC837XEMDS.h 
> b/include/configs/MPC837XEMDS.h
> index ed70b9e..adf7c8c 100644
> --- a/include/configs/MPC837XEMDS.h
> +++ b/include/configs/MPC837XEMDS.h
> @@ -347,6 +347,9 @@
>  #define CFG_PCI_SLV_MEM_SIZE	0x80000000
>  
>  #ifdef CONFIG_PCI
> +#ifndef __ASSEMBLY__
> +extern int board_pci_host_broken(void);
> +#endif
>  #define CONFIG_83XX_GENERIC_PCI	1 /* Use generic PCI setup */
>  #define CONFIG_PQ_MDS_PIB	1 /* PQ MDS Platform IO Board */
>  
> -- 
> 1.5.6.3
> _______________________________________________
> U-Boot mailing list
> U-Boot at lists.denx.de
> http://lists.denx.de/mailman/listinfo/u-boot
>