[U-Boot] [PATCH] ppc4xx: Merge Neo board port: CFG_ -> CONFIG_SYS_

[Stefan Roese]

Signed-off-by: Stefan Roese <sr at denx.de>
---
 include/configs/neo.h |   86 ++++++++++++++++++++++++------------------------
 1 files changed, 43 insertions(+), 43 deletions(-)

diff --git a/include/configs/neo.h b/include/configs/neo.h
index a150cdd..f275c7b 100644
--- a/include/configs/neo.h
+++ b/include/configs/neo.h
@@ -83,34 +83,34 @@
 #define CONFIG_SDRAM_BANK0	1	/* init onboard SDRAM bank 0 */
 
 /* SDRAM timings used in datasheet */
-#define CFG_SDRAM_CL            3	/* CAS latency */
-#define CFG_SDRAM_tRP           20	/* PRECHARGE command period */
-#define CFG_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
-#define CFG_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
-#define CFG_SDRAM_tRFC		66	/* Auto refresh period */
+#define CONFIG_SYS_SDRAM_CL            3	/* CAS latency */
+#define CONFIG_SYS_SDRAM_tRP           20	/* PRECHARGE command period */
+#define CONFIG_SYS_SDRAM_tRC           66	/* ACTIVE-to-ACTIVE command period */
+#define CONFIG_SYS_SDRAM_tRCD          20	/* ACTIVE-to-READ delay */
+#define CONFIG_SYS_SDRAM_tRFC		66	/* Auto refresh period */
 
 /*
- * If CFG_EXT_SERIAL_CLOCK, then the UART divisor is 1.
- * If CFG_405_UART_ERRATA_59, then UART divisor is 31.
- * Otherwise, UART divisor is determined by CPU Clock and CFG_BASE_BAUD value.
+ * If CONFIG_SYS_EXT_SERIAL_CLOCK, then the UART divisor is 1.
+ * If CONFIG_SYS_405_UART_ERRATA_59, then UART divisor is 31.
+ * Otherwise, UART divisor is determined by CPU Clock and CONFIG_SYS_BASE_BAUD value.
  * The Linux BASE_BAUD define should match this configuration.
  *    baseBaud = cpuClock/(uartDivisor*16)
- * If CFG_405_UART_ERRATA_59 and 200MHz CPU clock,
+ * If CONFIG_SYS_405_UART_ERRATA_59 and 200MHz CPU clock,
  * set Linux BASE_BAUD to 403200.
  */
 #undef	CONFIG_SERIAL_SOFTWARE_FIFO
-#undef  CFG_EXT_SERIAL_CLOCK           /* external serial clock */
-#undef  CFG_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
-#define CFG_BASE_BAUD		691200
+#undef  CONFIG_SYS_EXT_SERIAL_CLOCK           /* external serial clock */
+#undef  CONFIG_SYS_405_UART_ERRATA_59         /* 405GP/CR Rev. D silicon */
+#define CONFIG_SYS_BASE_BAUD		691200
 
 /*
  * I2C stuff
  */
-#define CFG_I2C_SPEED		100000	/* I2C speed and slave address	*/
+#define CONFIG_SYS_I2C_SPEED		100000	/* I2C speed and slave address	*/
 
 /* RTC */
 #define CONFIG_RTC_DS1337
-#define CFG_I2C_RTC_ADDR	0x68
+#define CONFIG_SYS_I2C_RTC_ADDR	0x68
 
 /* Temp sensor/hwmon/dtt */
 #define CONFIG_DTT_LM63		1	/* National LM63	*/
@@ -122,27 +122,27 @@
 /*
  * FLASH organization
  */
-#define CFG_FLASH_CFI				/* The flash is CFI compatible	*/
+#define CONFIG_SYS_FLASH_CFI				/* The flash is CFI compatible	*/
 #define CONFIG_FLASH_CFI_DRIVER			/* Use common CFI driver	*/
 
-#define CFG_FLASH_BASE		0xFC000000
-#define CFG_FLASH_BANKS_LIST	{ CFG_FLASH_BASE }
+#define CONFIG_SYS_FLASH_BASE		0xFC000000
+#define CONFIG_SYS_FLASH_BANKS_LIST	{ CONFIG_SYS_FLASH_BASE }
 
-#define CFG_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
-#define CFG_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
+#define CONFIG_SYS_MAX_FLASH_BANKS	1	/* max number of memory banks		*/
+#define CONFIG_SYS_MAX_FLASH_SECT	512	/* max number of sectors on one chip	*/
 
-#define CFG_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
-#define CFG_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
+#define CONFIG_SYS_FLASH_ERASE_TOUT	120000	/* Timeout for Flash Erase (in ms)	*/
+#define CONFIG_SYS_FLASH_WRITE_TOUT	500	/* Timeout for Flash Write (in ms)	*/
 
-#define CFG_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
-#define CFG_FLASH_PROTECTION	1	/* use hardware flash protection	*/
+#define CONFIG_SYS_FLASH_USE_BUFFER_WRITE 1	/* use buffered writes (20x faster)	*/
+#define CONFIG_SYS_FLASH_PROTECTION	1	/* use hardware flash protection	*/
 
-#define CFG_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
-#define CFG_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
+#define CONFIG_SYS_FLASH_EMPTY_INFO		/* print 'E' for empty sector on flinfo */
+#define CONFIG_SYS_FLASH_QUIET_TEST	1	/* don't warn upon unknown flash	*/
 
 #ifdef CONFIG_ENV_IS_IN_FLASH
 #define CONFIG_ENV_SECT_SIZE	0x20000	/* size of one complete sector		*/
-#define CONFIG_ENV_ADDR		((-CFG_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
+#define CONFIG_ENV_ADDR		((-CONFIG_SYS_MONITOR_LEN)-CONFIG_ENV_SECT_SIZE)
 #define	CONFIG_ENV_SIZE		0x2000	/* Total Size of Environment Sector	*/
 
 /* Address and size of Redundant Environment Sector	*/
@@ -153,7 +153,7 @@
 /*
  * PPC405 GPIO Configuration
  */
-#define CFG_4xx_GPIO_TABLE { /*				GPIO	Alternate1	*/	\
+#define CONFIG_SYS_4xx_GPIO_TABLE { /*				GPIO	Alternate1	*/	\
 {											\
 /* GPIO Core 0 */									\
 { GPIO_BASE, GPIO_OUT, GPIO_ALT1, GPIO_OUT_NO_CHG }, /* GPIO0	PerBLast    	*/	\
@@ -195,37 +195,37 @@
  * Definitions for initial stack pointer and data area (in data cache)
  */
 /* use on chip memory (OCM) for temperary stack until sdram is tested */
-#define CFG_TEMP_STACK_OCM        1
+#define CONFIG_SYS_TEMP_STACK_OCM        1
 
 /* On Chip Memory location */
-#define CFG_OCM_DATA_ADDR	0xF8000000
-#define CFG_OCM_DATA_SIZE	0x1000
-#define CFG_INIT_RAM_ADDR	CFG_OCM_DATA_ADDR /* inside of SDRAM		*/
-#define CFG_INIT_RAM_END	CFG_OCM_DATA_SIZE /* End of used area in RAM	*/
+#define CONFIG_SYS_OCM_DATA_ADDR	0xF8000000
+#define CONFIG_SYS_OCM_DATA_SIZE	0x1000
+#define CONFIG_SYS_INIT_RAM_ADDR	CONFIG_SYS_OCM_DATA_ADDR /* inside of SDRAM		*/
+#define CONFIG_SYS_INIT_RAM_END	CONFIG_SYS_OCM_DATA_SIZE /* End of used area in RAM	*/
 
-#define CFG_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
-#define CFG_GBL_DATA_OFFSET	(CFG_INIT_RAM_END - CFG_GBL_DATA_SIZE)
-#define CFG_INIT_SP_OFFSET	CFG_GBL_DATA_OFFSET
+#define CONFIG_SYS_GBL_DATA_SIZE	128  /* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_OFFSET	(CONFIG_SYS_INIT_RAM_END - CONFIG_SYS_GBL_DATA_SIZE)
+#define CONFIG_SYS_INIT_SP_OFFSET	CONFIG_SYS_GBL_DATA_OFFSET
 
 /*
  * External Bus Controller (EBC) Setup
  */
 
 /* Memory Bank 0 (NOR-FLASH) initialization                    */
-#define CFG_EBC_PB0AP		0x92015480
-#define CFG_EBC_PB0CR		0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB0AP		0x92015480
+#define CONFIG_SYS_EBC_PB0CR		0xFC0DA000  /* BAS=0xFC0,BS=64MB,BU=R/W,BW=16bit */
 
 /* Memory Bank 1 (NVRAM) initialization                                        */
-#define CFG_EBC_PB1AP		0x92015480
-#define CFG_EBC_PB1CR		0xFB85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit  */
+#define CONFIG_SYS_EBC_PB1AP		0x92015480
+#define CONFIG_SYS_EBC_PB1CR		0xFB85A000  /* BAS=0xFF8,BS=4MB,BU=R/W,BW=8bit  */
 
 /* Memory Bank 2 (FPGA) initialization                 */
 #define CONFIG_FPGA_BASE	0x7f100000
-#define CFG_EBC_PB2AP		0x92015480
-#define CFG_EBC_PB2CR		0x7f11a000  /* BAS=0x7f1,BS=1MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB2AP		0x92015480
+#define CONFIG_SYS_EBC_PB2CR		0x7f11a000  /* BAS=0x7f1,BS=1MB,BU=R/W,BW=16bit */
 
 /* Memory Bank 3 (Latches) initialization                      */
-#define CFG_EBC_PB3AP		0x92015480
-#define CFG_EBC_PB3CR		0x7f21a000  /* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */
+#define CONFIG_SYS_EBC_PB3AP		0x92015480
+#define CONFIG_SYS_EBC_PB3CR		0x7f21a000  /* BAS=0x7f2,BS=1MB,BU=R/W,BW=16bit */
 
 #endif	/* __CONFIG_H */
-- 
1.6.0.2