[U-Boot] [PATCH 13/19] ColdFire: Add mii driver in drivers/net
Tsi-Chung Liew
Tsi-Chung.Liew at freescale.com
Wed Oct 22 20:20:51 CEST 2008
From: TsiChung Liew <Tsi-Chung.Liew at freescale.com>
All CF platforms' mii.c are consolidated into one
Signed-off-by: TsiChung Liew <Tsi-Chung.Liew at freescale.com>
---
drivers/net/Makefile | 4 +-
drivers/net/mcffec.c | 18 +---
drivers/net/mcfmii.c | 321 ++++++++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 326 insertions(+), 17 deletions(-)
create mode 100644 drivers/net/mcfmii.c
diff --git a/drivers/net/Makefile b/drivers/net/Makefile
index 439c354..7e53136 100644
--- a/drivers/net/Makefile
+++ b/drivers/net/Makefile
@@ -35,13 +35,13 @@ COBJS-$(CONFIG_DRIVER_DM9000) += dm9000x.o
COBJS-$(CONFIG_E1000) += e1000.o
COBJS-$(CONFIG_EEPRO100) += eepro100.o
COBJS-$(CONFIG_ENC28J60) += enc28j60.o
-COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o
+COBJS-$(CONFIG_FSLDMAFEC) += fsl_mcdmafec.o mcfmii.o
COBJS-$(CONFIG_GRETH) += greth.o
COBJS-$(CONFIG_INCA_IP_SWITCH) += inca-ip_sw.o
COBJS-$(CONFIG_DRIVER_KS8695ETH) += ks8695eth.o
COBJS-$(CONFIG_DRIVER_LAN91C96) += lan91c96.o
COBJS-$(CONFIG_MACB) += macb.o
-COBJS-$(CONFIG_MCFFEC) += mcffec.o
+COBJS-$(CONFIG_MCFFEC) += mcffec.o mcfmii.o
COBJS-$(CONFIG_MPC5xxx_FEC) += mpc5xxx_fec.o
COBJS-$(CONFIG_MPC512x_FEC) += mpc512x_fec.o
COBJS-$(CONFIG_NATSEMI) += natsemi.o
diff --git a/drivers/net/mcffec.c b/drivers/net/mcffec.c
index c00474e..18240a8 100644
--- a/drivers/net/mcffec.c
+++ b/drivers/net/mcffec.c
@@ -27,14 +27,14 @@
#include <common.h>
#include <malloc.h>
-#include <asm/fec.h>
-#include <asm/immap.h>
-
#include <command.h>
#include <net.h>
#include <netdev.h>
#include <miiphy.h>
+#include <asm/fec.h>
+#include <asm/immap.h>
+
#undef ET_DEBUG
#undef MII_DEBUG
@@ -101,18 +101,6 @@ int fec_init(struct eth_device *dev, bd_t * bd);
void fec_halt(struct eth_device *dev);
void fec_reset(struct eth_device *dev);
-extern int fecpin_setclear(struct eth_device *dev, int setclear);
-
-#ifdef CONFIG_SYS_DISCOVER_PHY
-extern void __mii_init(void);
-extern uint mii_send(uint mii_cmd);
-extern int mii_discover_phy(struct eth_device *dev);
-extern int mcffec_miiphy_read(char *devname, unsigned char addr,
- unsigned char reg, unsigned short *value);
-extern int mcffec_miiphy_write(char *devname, unsigned char addr,
- unsigned char reg, unsigned short value);
-#endif
-
void setFecDuplexSpeed(volatile fec_t * fecp, bd_t * bd, int dup_spd)
{
if ((dup_spd >> 16) == FULL) {
diff --git a/drivers/net/mcfmii.c b/drivers/net/mcfmii.c
new file mode 100644
index 0000000..2b733c6
--- /dev/null
+++ b/drivers/net/mcfmii.c
@@ -0,0 +1,321 @@
+/*
+ * Copyright (C) 2004-2008 Freescale Semiconductor, Inc.
+ * TsiChung Liew (Tsi-Chung.Liew at freescale.com)
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
+ * MA 02111-1307 USA
+ */
+
+#include <common.h>
+#include <config.h>
+#include <net.h>
+#include <netdev.h>
+
+#ifdef CONFIG_MCF547x_8x
+#include <asm/fsl_mcdmafec.h>
+#else
+#include <asm/fec.h>
+#endif
+#include <asm/immap.h>
+
+DECLARE_GLOBAL_DATA_PTR;
+
+#if defined(CONFIG_CMD_NET) && defined(CONFIG_NET_MULTI)
+#undef MII_DEBUG
+#undef ET_DEBUG
+
+/*extern int fecpin_setclear(struct eth_device *dev, int setclear);*/
+
+#if defined(CONFIG_SYS_DISCOVER_PHY) || defined(CONFIG_CMD_MII)
+#include <miiphy.h>
+
+/* Make MII read/write commands for the FEC. */
+#define mk_mii_read(ADDR, REG) (0x60020000 | ((ADDR << 23) | \
+ (REG & 0x1f) << 18))
+#define mk_mii_write(ADDR, REG, VAL) (0x50020000 | ((ADDR << 23) | \
+ (REG & 0x1f) << 18) | (VAL & 0xffff))
+
+#ifndef CONFIG_SYS_UNSPEC_PHYID
+# define CONFIG_SYS_UNSPEC_PHYID 0
+#endif
+#ifndef CONFIG_SYS_UNSPEC_STRID
+# define CONFIG_SYS_UNSPEC_STRID 0
+#endif
+
+#ifdef CONFIG_MCF547x_8x
+typedef struct fec_info_dma FEC_INFO_T;
+#define FEC_T fecdma_t
+#else
+typedef struct fec_info_s FEC_INFO_T;
+#define FEC_T fec_t
+#endif
+
+typedef struct phy_info_struct {
+ u32 phyid;
+ char *strid;
+} phy_info_t;
+
+phy_info_t phyinfo[] = {
+ {0x0022561B, "AMD79C784VC"}, /* AMD 79C784VC */
+ {0x00406322, "BCM5222"}, /* Broadcom 5222 */
+ {0x02a80150, "Intel82555"}, /* Intel 82555 */
+ {0x0016f870, "LSI80225"}, /* LSI 80225 */
+ {0x0016f880, "LSI80225/B"}, /* LSI 80225/B */
+ {0x78100000, "LXT970"}, /* LXT970 */
+ {0x001378e0, "LXT971"}, /* LXT971 and 972 */
+ {0x00221619, "KS8721BL"}, /* Micrel KS8721BL/SL */
+ {0x00221512, "KSZ8041NL"}, /* Micrel KSZ8041NL */
+ {0x20005CE1, "N83640"}, /* National 83640 */
+ {0x20005C90, "N83848"}, /* National 83848 */
+ {0x20005CA2, "N83849"}, /* National 83849 */
+ {0x01814400, "QS6612"}, /* QS6612 */
+#if defined(CONFIG_SYS_UNSPEC_PHYID) && defined(CONFIG_SYS_UNSPEC_STRID)
+ {CONFIG_SYS_UNSPEC_PHYID, CONFIG_SYS_UNSPEC_STRID},
+#endif
+ {0, 0}
+};
+
+/*
+ * mii_init -- Initialize the MII for MII command without ethernet
+ * This function is a subset of eth_init
+ */
+void mii_reset(FEC_INFO_T *info)
+{
+ volatile FEC_T *fecp = (FEC_T *) (info->miibase);
+ int i;
+
+ fecp->ecr = FEC_ECR_RESET;
+
+ for (i = 0; (fecp->ecr & FEC_ECR_RESET) && (i < FEC_RESET_DELAY); ++i) {
+ udelay(1);
+ }
+ if (i == FEC_RESET_DELAY)
+ printf("FEC_RESET_DELAY timeout\n");
+}
+
+/* send command to phy using mii, wait for result */
+uint mii_send(uint mii_cmd)
+{
+ FEC_INFO_T *info;
+ volatile FEC_T *ep;
+ struct eth_device *dev;
+ uint mii_reply;
+ int j = 0;
+
+ /* retrieve from register structure */
+ dev = eth_get_dev();
+ info = dev->priv;
+
+ ep = (FEC_T *) info->miibase;
+
+ ep->mmfr = mii_cmd; /* command to phy */
+
+ /* wait for mii complete */
+ while (!(ep->eir & FEC_EIR_MII) && (j < MCFFEC_TOUT_LOOP)) {
+ udelay(1);
+ j++;
+ }
+ if (j >= MCFFEC_TOUT_LOOP) {
+ printf("MII not complete\n");
+ return -1;
+ }
+
+ mii_reply = ep->mmfr; /* result from phy */
+ ep->eir = FEC_EIR_MII; /* clear MII complete */
+#ifdef ET_DEBUG
+ printf("%s[%d] %s: sent=0x%8.8x, reply=0x%8.8x\n",
+ __FILE__, __LINE__, __FUNCTION__, mii_cmd, mii_reply);
+#endif
+
+ return (mii_reply & 0xffff); /* data read from phy */
+}
+#endif /* CONFIG_SYS_DISCOVER_PHY || (CONFIG_MII) */
+
+#if defined(CONFIG_SYS_DISCOVER_PHY)
+int mii_discover_phy(struct eth_device *dev)
+{
+#define MAX_PHY_PASSES 11
+ FEC_INFO_T *info = dev->priv;
+ int phyaddr, pass;
+ uint phyno, phytype;
+ int i, found = 0;
+
+ if (info->phyname_init)
+ return info->phy_addr;
+
+ phyaddr = -1; /* didn't find a PHY yet */
+ for (pass = 1; pass <= MAX_PHY_PASSES && phyaddr < 0; ++pass) {
+ if (pass > 1) {
+ /* PHY may need more time to recover from reset.
+ * The LXT970 needs 50ms typical, no maximum is
+ * specified, so wait 10ms before try again.
+ * With 11 passes this gives it 100ms to wake up.
+ */
+ udelay(10000); /* wait 10ms */
+ }
+
+ for (phyno = 0; phyno < 32 && phyaddr < 0; ++phyno) {
+
+ phytype = mii_send(mk_mii_read(phyno, PHY_PHYIDR1));
+#ifdef ET_DEBUG
+ printf("PHY type 0x%x pass %d type\n", phytype, pass);
+#endif
+ if (phytype != 0xffff) {
+ phyaddr = phyno;
+ phytype <<= 16;
+ phytype |=
+ mii_send(mk_mii_read(phyno, PHY_PHYIDR2));
+
+#ifdef ET_DEBUG
+ printf("PHY @ 0x%x pass %d\n", phyno, pass);
+#endif
+
+ for (i = 0; i < (sizeof(phyinfo) / sizeof(phy_info_t)); i++) {
+ if (phyinfo[i].phyid == phytype) {
+#ifdef ET_DEBUG
+ printf("phyid %x - %s\n",
+ phyinfo[i].phyid,
+ phyinfo[i].strid);
+#endif
+ strcpy(info->phy_name, phyinfo[i].strid);
+ info->phyname_init = 1;
+ found = 1;
+ break;
+ }
+ }
+
+ if (!found) {
+#ifdef ET_DEBUG
+ printf("0x%08x\n", phytype);
+#endif
+ strcpy(info->phy_name, "unknown");
+ info->phyname_init = 1;
+ break;
+ }
+ }
+ }
+ }
+
+ if (phyaddr < 0)
+ printf("No PHY device found.\n");
+
+ return phyaddr;
+}
+#endif /* CONFIG_SYS_DISCOVER_PHY */
+
+void mii_init(void) __attribute__((weak,alias("__mii_init")));
+
+void __mii_init(void)
+{
+ FEC_INFO_T *info;
+ volatile FEC_T *fecp;
+ struct eth_device *dev;
+ int miispd = 0, i = 0;
+ u16 autoneg = 0;
+
+ /* retrieve from register structure */
+ dev = eth_get_dev();
+ info = dev->priv;
+
+ fecp = (FEC_T *) info->miibase;
+
+ fecpin_setclear(dev, 1);
+
+ mii_reset(info);
+
+ /* We use strictly polling mode only */
+ fecp->eimr = 0;
+
+ /* Clear any pending interrupt */
+ fecp->eir = 0xffffffff;
+
+ /* Set MII speed */
+ miispd = (gd->bus_clk / 1000000) / 5;
+ fecp->mscr = miispd << 1;
+
+ info->phy_addr = mii_discover_phy(dev);
+
+#define AUTONEGLINK (PHY_BMSR_AUTN_COMP | PHY_BMSR_LS)
+ while (i < MCFFEC_TOUT_LOOP) {
+ autoneg = 0;
+ miiphy_read(dev->name, info->phy_addr, PHY_BMSR, &autoneg);
+ i++;
+
+ if ((autoneg & AUTONEGLINK) == AUTONEGLINK)
+ break;
+
+ udelay(500);
+ }
+ if (i >= MCFFEC_TOUT_LOOP) {
+ printf("Auto Negotiation not complete\n");
+ }
+
+ /* adapt to the half/full speed settings */
+ info->dup_spd = miiphy_duplex(dev->name, info->phy_addr) << 16;
+ info->dup_spd |= miiphy_speed(dev->name, info->phy_addr);
+}
+
+/*
+ * Read and write a MII PHY register, routines used by MII Utilities
+ *
+ * FIXME: These routines are expected to return 0 on success, but mii_send
+ * does _not_ return an error code. Maybe 0xFFFF means error, i.e.
+ * no PHY connected...
+ * For now always return 0.
+ * FIXME: These routines only work after calling eth_init() at least once!
+ * Otherwise they hang in mii_send() !!! Sorry!
+ */
+
+int mcffec_miiphy_read(char *devname, unsigned char addr, unsigned char reg,
+ unsigned short *value)
+{
+ short rdreg; /* register working value */
+
+#ifdef MII_DEBUG
+ printf("miiphy_read(0x%x) @ 0x%x = ", reg, addr);
+#endif
+ rdreg = mii_send(mk_mii_read(addr, reg));
+
+ *value = rdreg;
+
+#ifdef MII_DEBUG
+ printf("0x%04x\n", *value);
+#endif
+
+ return 0;
+}
+
+int mcffec_miiphy_write(char *devname, unsigned char addr, unsigned char reg,
+ unsigned short value)
+{
+ short rdreg; /* register working value */
+
+#ifdef MII_DEBUG
+ printf("miiphy_write(0x%x) @ 0x%x = ", reg, addr);
+#endif
+
+ rdreg = mii_send(mk_mii_write(addr, reg, value));
+
+#ifdef MII_DEBUG
+ printf("0x%04x\n", value);
+#endif
+
+ return 0;
+}
+
+#endif /* CONFIG_CMD_NET, FEC_ENET & NET_MULTI */
--
1.5.6.4
More information about the U-Boot
mailing list