[U-Boot] [PATCH] ppc4xx: Update PMC440 board support
matthias.fuchs at esd-electronics.com
matthias.fuchs at esd-electronics.com
Tue Oct 28 13:37:00 CET 2008
From: Matthias Fuchs <matthias.fuchs at esd-electronics.com>
This patch brings PMC440 board support up to date:
- fix GPIO configuration
- add misc_init_f()
- use better values for usbact variable
- fix USB 2.0 phy reset sequence
- shrink BAR2 to save PCI address space
- add FDT support
Signed-off-by: Matthias Fuchs <matthias.fuchs at esd-electronics.com>
---
board/esd/pmc440/pmc440.c | 128 +++++++++++++++++++++++++++++++++++++--------
1 files changed, 106 insertions(+), 22 deletions(-)
diff --git a/board/esd/pmc440/pmc440.c b/board/esd/pmc440/pmc440.c
index 013815e..8563d7d 100644
--- a/board/esd/pmc440/pmc440.c
+++ b/board/esd/pmc440/pmc440.c
@@ -1,5 +1,5 @@
/*
- * (C) Copyright 2007-2008
+ * (Cg) Copyright 2007-2008
* Matthias Fuchs, esd gmbh, matthias.fuchs at esd-electronics.com.
* Based on board/amcc/sequoia/sequoia.c
*
@@ -45,9 +45,11 @@
DECLARE_GLOBAL_DATA_PTR;
extern flash_info_t flash_info[CONFIG_SYS_MAX_FLASH_BANKS]; /* info for FLASH chips */
+extern void __ft_board_setup(void *blob, bd_t *bd);
ulong flash_get_size(ulong base, int banknum);
int pci_is_66mhz(void);
+int is_monarch(void);
int bootstrap_eeprom_read(unsigned dev_addr, unsigned offset,
uchar *buffer, unsigned cnt);
@@ -107,9 +109,9 @@ int board_early_init_f(void)
*/
out32(GPIO0_OR, 0x40000002);
out32(GPIO0_TCR, 0x4c90011f);
- out32(GPIO0_OSRL, 0x28011400);
+ out32(GPIO0_OSRL, 0x28051400);
out32(GPIO0_OSRH, 0x55005000);
- out32(GPIO0_TSRL, 0x08011400);
+ out32(GPIO0_TSRL, 0x08051400);
out32(GPIO0_TSRH, 0x55005000);
out32(GPIO0_ISR1L, 0x54000000);
out32(GPIO0_ISR1H, 0x00000000);
@@ -196,6 +198,23 @@ int board_early_init_f(void)
return 0;
}
+#if defined(CONFIG_MISC_INIT_F)
+int misc_init_f(void)
+{
+ struct pci_controller hose;
+ hose.first_busno = 0;
+ hose.last_busno = 0;
+ hose.region_count = 0;
+
+ if (getenv("pciearly") && (!is_monarch())) {
+ printf("PCI: early target init\n");
+ pci_setup_indirect(&hose, PCIX0_CFGADR, PCIX0_CFGDATA);
+ pci_target_init(&hose);
+ }
+ return 0;
+}
+#endif
+
/*
* misc_init_r.
*/
@@ -207,6 +226,7 @@ int misc_init_r(void)
unsigned long usb2d0cr = 0;
unsigned long usb2phy0cr, usb2h0cr = 0;
unsigned long sdr0_pfc1;
+ unsigned long sdr0_srst0, sdr0_srst1;
char *act = getenv("usbact");
/*
@@ -256,7 +276,7 @@ int misc_init_r(void)
/*
* USB suff...
*/
- if ((act == NULL || strcmp(act, "hostdev") == 0) &&
+ if ((act == NULL || strcmp(act, "host") == 0) &&
!(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)){
/* SDR Setting */
mfsdr(SDR0_PFC1, sdr0_pfc1);
@@ -290,12 +310,46 @@ int misc_init_r(void)
mtsdr(SDR0_USB2PHY0CR, usb2phy0cr);
mtsdr(SDR0_USB2H0CR, usb2h0cr);
- /* clear resets */
+ /*
+ * Take USB out of reset:
+ * -Initial status = all cores are in reset
+ * -deassert reset to OPB1, P4OPB0, OPB2, PLB42OPB1 OPB2PLB40 cores
+ * -wait 1 ms
+ * -deassert reset to PHY
+ * -wait 1 ms
+ * -deassert reset to HOST
+ * -wait 4 ms
+ * -deassert all other resets
+ */
+ mfsdr(SDR0_SRST1, sdr0_srst1);
+ sdr0_srst1 &= ~(SDR0_SRST1_OPBA1 | \
+ SDR0_SRST1_P4OPB0 | \
+ SDR0_SRST1_OPBA2 | \
+ SDR0_SRST1_PLB42OPB1 | \
+ SDR0_SRST1_OPB2PLB40);
+ mtsdr(SDR0_SRST1, sdr0_srst1);
+ udelay(1000);
+
+ mfsdr(SDR0_SRST1, sdr0_srst1);
+ sdr0_srst1 &= ~SDR0_SRST1_USB20PHY;
+ mtsdr(SDR0_SRST1, sdr0_srst1);
udelay(1000);
+
+ mfsdr(SDR0_SRST0, sdr0_srst0);
+ sdr0_srst0 &= ~SDR0_SRST0_USB2H;
+ mtsdr(SDR0_SRST0, sdr0_srst0);
+ udelay(4000);
+
+ /* finally all the other resets */
mtsdr(SDR0_SRST1, 0x00000000);
- udelay(1000);
mtsdr(SDR0_SRST0, 0x00000000);
+ if (!(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT)) {
+ /* enable power on USB socket */
+ out_be32((void*)GPIO1_OR,
+ in_be32((void*)GPIO1_OR) & ~GPIO1_USB_PWR_N);
+ }
+
printf("USB: Host\n");
} else if ((strcmp(act, "dev") == 0) ||
@@ -547,14 +601,14 @@ void pci_target_init(struct pci_controller *hose)
out32r(PCIX0_PTM2MS, simple_strtoul(ptmms_str, NULL, 16));
out32r(PCIX0_PTM2LA, simple_strtoul(ptmla_str, NULL, 16));
} else {
- /* BAR2: default: 16 MB FPGA + registers */
- out32r(PCIX0_PTM2MS, 0xff000001); /* Memory Size/Attribute */
+ /* BAR2: default: 4MB FPGA */
+ out32r(PCIX0_PTM2MS, 0xffc00001); /* Memory Size/Attribute */
out32r(PCIX0_PTM2LA, 0xef000000); /* Local Addr. Reg */
}
if (is_monarch()) {
/* BAR2: map FPGA registers behind system memory at 1GB */
- pci_write_config_dword(0, PCI_BASE_ADDRESS_2, 0x40000008);
+ pci_hose_write_config_dword(hose, 0, PCI_BASE_ADDRESS_2, 0x40000008);
}
/*
@@ -562,8 +616,8 @@ void pci_target_init(struct pci_controller *hose)
*/
/* Program the board's vendor id */
- pci_write_config_word(0, PCI_SUBSYSTEM_VENDOR_ID,
- CONFIG_SYS_PCI_SUBSYS_VENDORID);
+ pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_VENDOR_ID,
+ CONFIG_SYS_PCI_SUBSYS_VENDORID);
/* disabled for PMC405 backward compatibility */
/* Configure command register as bus master */
@@ -571,19 +625,19 @@ void pci_target_init(struct pci_controller *hose)
/* 240nS PCI clock */
- pci_write_config_word(0, PCI_LATENCY_TIMER, 1);
+ pci_hose_write_config_word(hose, 0, PCI_LATENCY_TIMER, 1);
/* No error reporting */
- pci_write_config_word(0, PCI_ERREN, 0);
+ pci_hose_write_config_word(hose, 0, PCI_ERREN, 0);
pci_write_config_dword(0, PCI_BRDGOPT2, 0x00000101);
if (!is_monarch()) {
/* Program the board's subsystem id/classcode */
- pci_write_config_word(0, PCI_SUBSYSTEM_ID,
- CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH);
- pci_write_config_word(0, PCI_CLASS_SUB_CODE,
- CONFIG_SYS_PCI_CLASSCODE_NONMONARCH);
+ pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_ID,
+ CONFIG_SYS_PCI_SUBSYS_ID_NONMONARCH);
+ pci_hose_write_config_word(hose, 0, PCI_CLASS_SUB_CODE,
+ CONFIG_SYS_PCI_CLASSCODE_NONMONARCH);
/* PCI configuration done: release ERREADY */
out_be32((void*)GPIO1_OR,
@@ -592,11 +646,14 @@ void pci_target_init(struct pci_controller *hose)
in_be32((void*)GPIO1_TCR) | GPIO1_PPC_EREADY);
} else {
/* Program the board's subsystem id/classcode */
- pci_write_config_word(0, PCI_SUBSYSTEM_ID,
- CONFIG_SYS_PCI_SUBSYS_ID_MONARCH);
- pci_write_config_word(0, PCI_CLASS_SUB_CODE,
- CONFIG_SYS_PCI_CLASSCODE_MONARCH);
+ pci_hose_write_config_word(hose, 0, PCI_SUBSYSTEM_ID,
+ CONFIG_SYS_PCI_SUBSYS_ID_MONARCH);
+ pci_hose_write_config_word(hose, 0, PCI_CLASS_SUB_CODE,
+ CONFIG_SYS_PCI_CLASSCODE_MONARCH);
}
+
+ /* enable host configuration */
+ pci_hose_write_config_dword(hose, 0, PCI_BRDGOPT2, 0x00000101);
}
#endif /* defined(CONFIG_PCI) && defined(CONFIG_SYS_PCI_TARGET_INIT) */
@@ -626,6 +683,12 @@ static void wait_for_pci_ready(void)
{
int i;
char *s = getenv("pcidelay");
+ /*
+ * We have our own handling of the pcidelay variable.
+ * Using CONFIG_PCI_BOOTDELAY enables pausing for host
+ * and adapter devices. For adapter devices we do not
+ * want this.
+ */
if (s) {
int ms = simple_strtoul(s, NULL, 10);
printf("PCI: Waiting for %d ms\n", ms);
@@ -851,7 +914,7 @@ int usb_board_init(void)
char *act = getenv("usbact");
int i;
- if ((act == NULL || strcmp(act, "hostdev") == 0) &&
+ if ((act == NULL || strcmp(act, "host") == 0) &&
!(in_be32((void*)GPIO0_IR) & GPIO0_USB_PRSNT))
/* enable power on USB socket */
out_be32((void*)GPIO1_OR,
@@ -876,3 +939,24 @@ int usb_board_init_fail(void)
return 0;
}
#endif /* defined(CONFIG_USB_OHCI) && defined(CONFIG_SYS_USB_OHCI_BOARD_INIT) */
+
+#if defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP)
+void ft_board_setup(void *blob, bd_t *bd)
+{
+ int rc;
+
+ __ft_board_setup(blob, bd);
+
+ /*
+ * Disable PCI in non-monarch mode.
+ */
+ if (!is_monarch()) {
+ rc = fdt_find_and_setprop(blob, "/plb/pci at 1ec000000", "status",
+ "disabled", sizeof("disabled"), 1);
+ if (rc) {
+ printf("Unable to update property status in PCI node, err=%s\n",
+ fdt_strerror(rc));
+ }
+ }
+}
+#endif /* defined(CONFIG_OF_LIBFDT) && defined(CONFIG_OF_BOARD_SETUP) */
--
1.5.3
More information about the U-Boot
mailing list