[U-Boot] [PATCH 2/2] NAND: Add NAND support for MPC8536DS board

[Kumar Gala]

From: Jason Jin <Jason.Jin at freescale.com>

This patch defines 1M TLB&LAW size for NAND on MPC8536DS, assigns 0xffa00000
for CONFIG_SYS_NAND_BASE and adds other NAND supports in config file.
It also moves environment(CONFIG_ENV_ADDR) outside of u-boot image.

Singed-off-by: Jason Jin <Jason.Jin at freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang at freescale.com>
Signed-off-by: Kumar Gala <galak at kernel.crashing.org>
---
 board/freescale/mpc8536ds/law.c |    1 +
 board/freescale/mpc8536ds/tlb.c |    5 +++
 include/configs/MPC8536DS.h     |   56 +++++++++++++++++++++++++++++++++++++-
 3 files changed, 60 insertions(+), 2 deletions(-)

diff --git a/board/freescale/mpc8536ds/law.c b/board/freescale/mpc8536ds/law.c
index 8013d41..0861fa7 100644
--- a/board/freescale/mpc8536ds/law.c
+++ b/board/freescale/mpc8536ds/law.c
@@ -38,6 +38,7 @@ struct law_entry law_table[] = {
 	SET_LAW(CONFIG_SYS_PCIE3_MEM_PHYS, LAWAR_SIZE_512M, LAW_TRGT_IF_PCIE_3),
 	SET_LAW(CONFIG_SYS_PCIE3_IO_PHYS, LAW_SIZE_64K, LAW_TRGT_IF_PCIE_3),
 	SET_LAW(PIXIS_BASE, LAW_SIZE_4K, LAW_TRGT_IF_LBC),
+	SET_LAW(CONFIG_SYS_NAND_BASE_PHYS, LAW_SIZE_1M, LAW_TRGT_IF_LBC),
 };

 int num_law_entries = ARRAY_SIZE(law_table);
diff --git a/board/freescale/mpc8536ds/tlb.c b/board/freescale/mpc8536ds/tlb.c
index ebf41ce..c81a959 100644
--- a/board/freescale/mpc8536ds/tlb.c
+++ b/board/freescale/mpc8536ds/tlb.c
@@ -66,6 +66,11 @@ struct fsl_e_tlb_entry tlb_table[] = {
 	SET_TLB_ENTRY(1, CONFIG_SYS_PCI1_IO_PHYS, CONFIG_SYS_PCI1_IO_PHYS,
 		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
 		      0, 3, BOOKE_PAGESZ_256K, 1),
+
+	/* *I*G - NAND */
+	SET_TLB_ENTRY(1, CONFIG_SYS_NAND_BASE, CONFIG_SYS_NAND_BASE_PHYS,
+		      MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
+		      0, 4, BOOKE_PAGESZ_1M, 1),
 };

 int num_tlb_entries = ARRAY_SIZE(tlb_table);
diff --git a/include/configs/MPC8536DS.h b/include/configs/MPC8536DS.h
index c4389cc..fff888a 100644
--- a/include/configs/MPC8536DS.h
+++ b/include/configs/MPC8536DS.h
@@ -155,8 +155,9 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
  * 0xXXXX_XXXX	0xXXXX_XXXX	SRAM			YZ M Cacheable
  *
  * Localbus non-cacheable
- * 0xe000_0000	0xe80f_ffff	Promjet/free		128M non-cacheable
+ * 0xe000_0000	0xe7ff_ffff	Promjet/free		128M non-cacheable
  * 0xe800_0000	0xefff_ffff	FLASH			128M non-cacheable
+ * 0xffa0_0000	0xffaf_ffff	NAND			1M non-cacheable
  * 0xffdf_0000	0xffdf_7fff	PIXIS			32K non-cacheable TLB0
  * 0xffd0_0000	0xffd0_3fff	L1 for stack		16K Cacheable TLB0
  * 0xffe0_0000	0xffef_ffff	CCSR			1M non-cacheable
@@ -243,6 +244,57 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #define CONFIG_SYS_MONITOR_LEN		(256 * 1024) /* Reserve 256 kB for Mon */
 #define CONFIG_SYS_MALLOC_LEN		(1024 * 1024)	/* Reserved for malloc */

+#define CONFIG_SYS_NAND_BASE           0xffa00000
+#define CONFIG_SYS_NAND_BASE_PHYS      CONFIG_SYS_NAND_BASE
+#define CONFIG_SYS_NAND_BASE_LIST     { CONFIG_SYS_NAND_BASE,\
+				CONFIG_SYS_NAND_BASE + 0x40000, \
+				CONFIG_SYS_NAND_BASE + 0x80000, \
+				CONFIG_SYS_NAND_BASE + 0xC0000}
+#define CONFIG_SYS_MAX_NAND_DEVICE	4
+#define NAND_MAX_CHIPS		1
+#define CONFIG_MTD_NAND_VERIFY_WRITE
+#define CONFIG_CMD_NAND		1
+#define CONFIG_NAND_FSL_ELBC	1
+#define CONFIG_SYS_NAND_BLOCK_SIZE	(128 * 1024)
+
+/* NAND flash config */
+#define CONFIG_NAND_BR_PRELIM	(CONFIG_SYS_NAND_BASE_PHYS \
+				| (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+				| BR_PS_8              /* Port Size = 8 bit */ \
+				| BR_MS_FCM             /* MSEL = FCM */ \
+				| BR_V)                 /* valid */
+#define CONFIG_NAND_OR_PRELIM	(0xFFFC0000            /* length 256K */ \
+				| OR_FCM_PGS            /* Large Page*/ \
+				| OR_FCM_CSCT \
+				| OR_FCM_CST \
+				| OR_FCM_CHT \
+				| OR_FCM_SCY_1 \
+				| OR_FCM_TRLX \
+				| OR_FCM_EHTR)
+
+#define CONFIG_SYS_BR2_PRELIM  CONFIG_NAND_BR_PRELIM  /* NAND Base Address */
+#define CONFIG_SYS_OR2_PRELIM  CONFIG_NAND_OR_PRELIM  /* NAND Options */
+
+#define CONFIG_SYS_BR4_PRELIM  ((CONFIG_SYS_NAND_BASE_PHYS + 0x40000)\
+				| (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+				| BR_PS_8              /* Port Size = 8 bit */ \
+				| BR_MS_FCM             /* MSEL = FCM */ \
+				| BR_V)                 /* valid */
+#define CONFIG_SYS_OR4_PRELIM	CONFIG_NAND_OR_PRELIM     /* NAND Options */
+#define CONFIG_SYS_BR5_PRELIM  ((CONFIG_SYS_NAND_BASE_PHYS + 0x80000)\
+				| (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+				| BR_PS_8              /* Port Size = 8 bit */ \
+				| BR_MS_FCM             /* MSEL = FCM */ \
+				| BR_V)                 /* valid */
+#define CONFIG_SYS_OR5_PRELIM	CONFIG_NAND_OR_PRELIM     /* NAND Options */
+
+#define CONFIG_SYS_BR6_PRELIM  ((CONFIG_SYS_NAND_BASE_PHYS + 0xC0000)\
+				| (2<<BR_DECC_SHIFT)    /* Use HW ECC */ \
+				| BR_PS_8              /* Port Size = 8 bit */ \
+				| BR_MS_FCM             /* MSEL = FCM */ \
+				| BR_V)                 /* valid */
+#define CONFIG_SYS_OR6_PRELIM	CONFIG_NAND_OR_PRELIM     /* NAND Options */
+
 /* Serial Port - controlled on board with jumper J8
  * open - index 2
  * shorted - index 1
@@ -440,7 +492,7 @@ extern unsigned long get_board_ddr_clk(unsigned long dummy);
 #if CONFIG_SYS_MONITOR_BASE > 0xfff80000
 #define CONFIG_ENV_ADDR		0xfff80000
 #else
-#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE + 0x60000)
+#define CONFIG_ENV_ADDR		(CONFIG_SYS_MONITOR_BASE - CONFIG_ENV_SECT_SIZE)
 #endif
 #define CONFIG_ENV_SIZE		0x2000
 #define CONFIG_ENV_SECT_SIZE	0x20000 /* 128K (one sector) */
-- 
1.5.5.1