[U-Boot] [PATCH] ZOOM2 Mux changes to support zoom2 configuration.

[Tom Rix]

Signed-off-by: Tom Rix <Tom.Rix at windriver.com>
---
 board/omap3/zoom2/zoom2.h |   20 +++++++++++++++++++-
 1 files changed, 19 insertions(+), 1 deletions(-)

diff --git a/board/omap3/zoom2/zoom2.h b/board/omap3/zoom2/zoom2.h
index 3199fa9..47401f7 100644
--- a/board/omap3/zoom2/zoom2.h
+++ b/board/omap3/zoom2/zoom2.h
@@ -129,6 +129,24 @@ const omap3_sysinfo sysinfo = {
  MUX_VAL(CP(GPMC_WAIT0),	(IEN  | PTD | EN  | M0)) /*GPMC_WAIT0*/\
  MUX_VAL(CP(GPMC_WAIT1),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT1*/\
  MUX_VAL(CP(GPMC_WAIT2),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT2*/\
- MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT3*/
+ MUX_VAL(CP(GPMC_WAIT3),	(IEN  | PTU | EN  | M0)) /*GPMC_WAIT3*/\
+ /* IDCC modem Power On */					       \
+ MUX_VAL(CP(CAM_D11),           (IEN  | PTU | EN | M4)) /*GPIO_110*/\
+ MUX_VAL(CP(CAM_D4),            (IEN  | PTU | EN | M4)) /*GPIO_103 */\
+ /* GPMC CS7 has LAN9211 device */\
+ MUX_VAL(CP(GPMC_NCS7),         (IDIS | PTU | EN  | M0)) /*GPMC_nCS7*/\
+ MUX_VAL(CP(MCBSP1_DX),         (IEN  | PTD | DIS | M4)) /*LAN9221*/\
+ MUX_VAL(CP(MCSPI1_CS2),        (IEN  | PTD | EN  | M0)) /*MCSPI1_CS2*/\
+ /* GPMC CS3 has Serial TL16CP754C device */\
+ MUX_VAL(CP(GPMC_NCS3),         (IDIS | PTU | EN  | M0)) /*GPMC_nCS3*/\
+ /* Toggle Reset pin of TL16CP754C device */\
+ MUX_VAL(CP(MCBSP4_CLKX),       (IEN  | PTU | EN  | M4)) /*GPIO_152*/\
+ udelay(10);\
+ MUX_VAL(CP(MCBSP4_CLKX),       (IEN  | PTD | EN  | M4)) /*GPIO_152*/\
+ MUX_VAL(CP(SDRC_CKE1),         (IDIS | PTU | EN  | M0)) /*SDRC_CKE1*/\
+ /* LEDS */\
+ MUX_VAL(CP(MCSPI1_SOMI),       (IEN  | PTD | EN | M4))  /*GPIO_173 red */\
+ MUX_VAL(CP(MCBSP4_DX),         (IEN  | PTD | EN | M4))  /*GPIO_154 blue */\
+ MUX_VAL(CP(GPMC_NBE1),         (IEN  | PTD | EN | M4))  /*GPIO_61 blue2 */
 
 #endif /* _BOARD_ZOOM_H_ */
-- 
1.6.0.5