[U-Boot] [patch u-boot git arm/next] davinci: display correct clock info

David Brownell david-b at pacbell.net
Thu Apr 30 00:38:09 CEST 2009


From: David Brownell <dbrownell at users.sourceforge.net>

Make the DaVinci clock display code work on the dm355 too ... there
are pre- and post- dividers on its PLLs, which most other DaVinci
processors don't use; and it uses different PLL dividers.  Stubbed
in support for the DM6467 too.  Verified on dm355 and dm6446.

Signed-off-by: David Brownell <dbrownell at users.sourceforge.net>
---
This should move to cpu/arm926ejs/davinci (cpuinfo.c?) someday,
like the other SoC-specific code.  For another patch.

 board/davinci/common/misc.c |   88 +++++++++++++++++++++++++++++++++++++++---
 1 file changed, 83 insertions(+), 5 deletions(-)

--- a/board/davinci/common/misc.c
+++ b/board/davinci/common/misc.c
@@ -28,6 +28,40 @@
 #include <net.h>
 #include <asm/arch/hardware.h>
 
+
+/* offsets from PLL controller base */
+#define PLLC_PLLCTL	0x100
+#define PLLC_PLLM	0x110
+#define PLLC_PREDIV	0x114
+#define PLLC_PLLDIV1	0x118
+#define PLLC_PLLDIV2	0x11c
+#define PLLC_PLLDIV3	0x120
+#define PLLC_POSTDIV	0x128
+#define PLLC_BPDIV	0x12c
+#define PLLC_PLLDIV4	0x160
+#define PLLC_PLLDIV5	0x164
+#define PLLC_PLLDIV6	0x168
+#define PLLC_PLLDIV8	0x170
+#define PLLC_PLLDIV9	0x174
+
+#define BIT(x)		(1 << (x))
+
+/* SOC-specific pll info */
+#ifdef CONFIG_SOC_DM355
+#define ARM_PLLDIV	PLLC_PLLDIV1
+#define DDR_PLLDIV	PLLC_PLLDIV1
+#endif
+
+#ifdef CONFIG_SOC_DM644X
+#define ARM_PLLDIV	PLLC_PLLDIV2
+#define DDR_PLLDIV	PLLC_PLLDIV2
+#endif
+
+#ifdef CONFIG_SOC_DM6447
+#define ARM_PLLDIV	PLLC_PLLDIV2
+#define DDR_PLLDIV	PLLC_PLLDIV1
+#endif
+
 DECLARE_GLOBAL_DATA_PTR;
 
 int dram_init(void)
@@ -38,16 +72,60 @@ int dram_init(void)
 	return(0);
 }
 
-static int dv_get_pllm_output(uint32_t pllm)
+static unsigned pll_div(volatile void *pllbase, unsigned offset)
 {
-	return (pllm + 1) * (CONFIG_SYS_HZ_CLOCK / 1000000);
+	u32	div;
+
+	div = REG(pllbase + offset);
+	return (div & BIT(15)) ? (1 + (div & 0x1f)) : 1;
+}
+
+static inline unsigned pll_prediv(volatile void *pllbase)
+{
+#ifdef CONFIG_SOC_DM355
+	/* this register read seems to fail on pll0 */
+	if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE)
+		return 8;
+	else
+		return pll_div(pllbase, PLLC_PREDIV);
+#endif
+	return 1;
+}
+
+static inline unsigned pll_postdiv(volatile void *pllbase)
+{
+#ifdef CONFIG_SOC_DM355
+	return pll_div(pllbase, PLLC_POSTDIV);
+#elif defined(CONFIG_SOC_DM6446)
+	if (pllbase == (volatile void *)DAVINCI_PLL_CNTRL0_BASE)
+		return pll_div(pllbase, PLLC_POSTDIV);
+#endif
+	return 1;
+}
+
+static unsigned pll_sysclk_mhz(unsigned pll_addr, unsigned div)
+{
+	volatile void	*pllbase = (volatile void *) pll_addr;
+	unsigned	base = CONFIG_SYS_HZ_CLOCK / 1000;
+
+	/* the PLL might be bypassed */
+	if (REG(pllbase + PLLC_PLLCTL) & BIT(0)) {
+		base /= pll_prediv(pllbase);
+		base *= 1 + (REG(pllbase + PLLC_PLLM) & 0x0ff);
+		base /= pll_postdiv(pllbase);
+	}
+	return DIV_ROUND_UP(base, 1000 * pll_div(pllbase, div));
 }
 
 void dv_display_clk_infos(void)
 {
-	printf("ARM Clock: %dMHz\n", dv_get_pllm_output(REG(PLL1_PLLM)) / 2);
-	printf("DDR Clock: %dMHz\n", dv_get_pllm_output(REG(PLL2_PLLM)) /
-	       ((REG(PLL2_DIV2) & 0x1f) + 1) / 2);
+	printf("ARM Clock: %dMHz\n",
+			pll_sysclk_mhz(DAVINCI_PLL_CNTRL0_BASE, ARM_PLLDIV));
+	printf("DDR Clock: %dMHz\n",
+			/* DDR PHY uses an x2 input clock */
+			pll_sysclk_mhz(DAVINCI_PLL_CNTRL1_BASE, DDR_PLLDIV)
+				/ 2);
+	printf("\n");
 }
 
 #ifdef CONFIG_DRIVER_TI_EMAC


More information about the U-Boot mailing list