[U-Boot] [PATCH 3/3] mpc83xx: Add PCI-E support for MPC837XEMDS boards
Anton Vorontsov
avorontsov at ru.mvista.com
Thu Jan 8 02:26:19 CET 2009
MPC837XEMDS boards can support PCI-E via "PCI-E riser card". The card
provides two PCI-E (x2) ports. Though, only one port can be used in x2
mode. Two ports can function simultaneously in x1 mode.
PCI-E x1/x2 modes can be switched via "pex_x2" environment variable.
Signed-off-by: Anton Vorontsov <avorontsov at ru.mvista.com>
---
board/freescale/mpc837xemds/mpc837xemds.c | 6 +-
board/freescale/mpc837xemds/pci.c | 89 ++++++++++++++++++++++++++++-
board/freescale/mpc837xemds/pci.h | 6 ++
include/configs/MPC837XEMDS.h | 21 +++++++
4 files changed, 117 insertions(+), 5 deletions(-)
create mode 100644 board/freescale/mpc837xemds/pci.h
diff --git a/board/freescale/mpc837xemds/mpc837xemds.c b/board/freescale/mpc837xemds/mpc837xemds.c
index acf8ada..156d808 100644
--- a/board/freescale/mpc837xemds/mpc837xemds.c
+++ b/board/freescale/mpc837xemds/mpc837xemds.c
@@ -18,6 +18,7 @@
#include <tsec.h>
#include <libfdt.h>
#include <fdt_support.h>
+#include "pci.h"
#include "../common/pq-mds-pib.h"
int board_early_init_f(void)
@@ -38,14 +39,10 @@ int board_early_init_f(void)
case SPR_8377:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
break;
case SPR_8378:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SGMII,
FSL_SERDES_CLK_125, FSL_SERDES_VDD_1V);
- fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
- FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
break;
case SPR_8379:
fsl_setup_serdes(CONFIG_FSL_SERDES1, FSL_SERDES_PROTO_SATA,
@@ -316,6 +313,7 @@ void ft_board_setup(void *blob, bd_t *bd)
ft_pci_setup(blob, bd);
if (board_pci_host_broken())
ft_pci_fixup(blob, bd);
+ ft_pcie_fixup(blob, bd);
#endif
}
#endif /* CONFIG_OF_BOARD_SETUP */
diff --git a/board/freescale/mpc837xemds/pci.c b/board/freescale/mpc837xemds/pci.c
index df4e748..31116b3 100644
--- a/board/freescale/mpc837xemds/pci.c
+++ b/board/freescale/mpc837xemds/pci.c
@@ -16,7 +16,9 @@
#include <mpc83xx.h>
#include <pci.h>
#include <i2c.h>
+#include <fdt_support.h>
#include <asm/fsl_i2c.h>
+#include <asm/fsl_serdes.h>
#if defined(CONFIG_PCI)
static struct pci_region pci_regions[] = {
@@ -40,15 +42,59 @@ static struct pci_region pci_regions[] = {
}
};
+static struct pci_region pcie_regions_0[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE1_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE1_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE1_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE1_IO_PHYS,
+ .size = CONFIG_SYS_PCIE1_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+static struct pci_region pcie_regions_1[] = {
+ {
+ .bus_start = CONFIG_SYS_PCIE2_MEM_BASE,
+ .phys_start = CONFIG_SYS_PCIE2_MEM_PHYS,
+ .size = CONFIG_SYS_PCIE2_MEM_SIZE,
+ .flags = PCI_REGION_MEM,
+ },
+ {
+ .bus_start = CONFIG_SYS_PCIE2_IO_BASE,
+ .phys_start = CONFIG_SYS_PCIE2_IO_PHYS,
+ .size = CONFIG_SYS_PCIE2_IO_SIZE,
+ .flags = PCI_REGION_IO,
+ },
+};
+
+static int is_pex_x2(void)
+{
+ const char *pex_x2 = getenv("pex_x2");
+
+ if (pex_x2 && !strcmp(pex_x2, "yes"))
+ return 1;
+ return 0;
+}
+
void pci_init_board(void)
{
volatile immap_t *immr = (volatile immap_t *)CONFIG_SYS_IMMR;
+ volatile sysconf83xx_t *sysconf = &immr->sysconf;
volatile clk83xx_t *clk = (volatile clk83xx_t *)&immr->clk;
volatile law83xx_t *pci_law = immr->sysconf.pcilaw;
+ volatile law83xx_t *pcie_law = sysconf->pcielaw;
struct pci_region *reg[] = { pci_regions };
+ struct pci_region *pcie_reg[] = { pcie_regions_0, pcie_regions_1, };
+ u32 spridr = in_be32(&immr->sysconf.spridr);
+ int pex2 = is_pex_x2();
if (board_pci_host_broken())
- return;
+ goto skip_pci;
/* Enable all 5 PCI_CLK_OUTPUTS */
clk->occr |= 0xf8000000;
@@ -64,5 +110,46 @@ void pci_init_board(void)
udelay(2000);
mpc83xx_pci_init(1, reg, 0);
+skip_pci:
+ /* There is no PEX in MPC8379 parts. */
+ if (PARTID_NO_E(spridr) == SPR_8379)
+ return;
+
+ /* Configure the clock for PCIE controller */
+ clrsetbits_be32(&clk->sccr, SCCR_PCIEXP1CM | SCCR_PCIEXP2CM,
+ SCCR_PCIEXP1CM_1 | SCCR_PCIEXP2CM_1);
+
+ /* Deassert the resets in the control register */
+ out_be32(&sysconf->pecr1, 0xE0008000);
+ if (!pex2)
+ out_be32(&sysconf->pecr2, 0xE0008000);
+ udelay(2000);
+
+ /* Configure PCI Express Local Access Windows */
+ out_be32(&pcie_law[0].bar, CONFIG_SYS_PCIE1_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[0].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ out_be32(&pcie_law[1].bar, CONFIG_SYS_PCIE2_BASE & LAWBAR_BAR);
+ out_be32(&pcie_law[1].ar, LBLAWAR_EN | LBLAWAR_512MB);
+
+ if (pex2)
+ fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX_X2,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+ else
+ fsl_setup_serdes(CONFIG_FSL_SERDES2, FSL_SERDES_PROTO_PEX,
+ FSL_SERDES_CLK_100, FSL_SERDES_VDD_1V);
+
+ mpc83xx_pcie_init(pex2 ? 1 : 2, pcie_reg, 0);
+}
+
+void ft_pcie_fixup(void *blob, bd_t *bd)
+{
+ const char *status = "disabled (PCIE1 is x2)";
+
+ if (!is_pex_x2())
+ return;
+
+ do_fixup_by_path(blob, "pci2", "status", status,
+ strlen(status) + 1, 1);
}
#endif /* CONFIG_PCI */
diff --git a/board/freescale/mpc837xemds/pci.h b/board/freescale/mpc837xemds/pci.h
new file mode 100644
index 0000000..fd7a916
--- /dev/null
+++ b/board/freescale/mpc837xemds/pci.h
@@ -0,0 +1,6 @@
+#ifndef __BOARD_MPC837XEMDS_PCI_H
+#define __BOARD_MPC837XEMDS_PCI_H
+
+extern void ft_pcie_fixup(void *blob, bd_t *bd);
+
+#endif /* __BOARD_MPC837XEMDS_PCI_H */
diff --git a/include/configs/MPC837XEMDS.h b/include/configs/MPC837XEMDS.h
index d49155f..28d442b 100644
--- a/include/configs/MPC837XEMDS.h
+++ b/include/configs/MPC837XEMDS.h
@@ -354,11 +354,32 @@
#define CONFIG_SYS_PCI_SLV_MEM_BUS 0x00000000
#define CONFIG_SYS_PCI_SLV_MEM_SIZE 0x80000000
+#define CONFIG_SYS_PCIE1_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_CFG_BASE 0xA0000000
+#define CONFIG_SYS_PCIE1_CFG_SIZE 0x08000000
+#define CONFIG_SYS_PCIE1_MEM_BASE 0xA8000000
+#define CONFIG_SYS_PCIE1_MEM_PHYS 0xA8000000
+#define CONFIG_SYS_PCIE1_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE1_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE1_IO_PHYS 0xB8000000
+#define CONFIG_SYS_PCIE1_IO_SIZE 0x00800000
+
+#define CONFIG_SYS_PCIE2_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_CFG_BASE 0xC0000000
+#define CONFIG_SYS_PCIE2_CFG_SIZE 0x08000000
+#define CONFIG_SYS_PCIE2_MEM_BASE 0xC8000000
+#define CONFIG_SYS_PCIE2_MEM_PHYS 0xC8000000
+#define CONFIG_SYS_PCIE2_MEM_SIZE 0x10000000
+#define CONFIG_SYS_PCIE2_IO_BASE 0x00000000
+#define CONFIG_SYS_PCIE2_IO_PHYS 0xD8000000
+#define CONFIG_SYS_PCIE2_IO_SIZE 0x00800000
+
#ifdef CONFIG_PCI
#ifndef __ASSEMBLY__
extern int board_pci_host_broken(void);
#endif
#define CONFIG_83XX_GENERIC_PCI 1 /* Use generic PCI setup */
+#define CONFIG_83XX_GENERIC_PCIE 1
#define CONFIG_PQ_MDS_PIB 1 /* PQ MDS Platform IO Board */
#define CONFIG_HAS_FSL_DR_USB 1 /* fixup device tree for the DR USB */
--
1.5.6.5
More information about the U-Boot
mailing list