[U-Boot] [PATCH 5/5] P2020RDB Platform support added.
Aggrwal Poonam-B10812
Poonam.Aggrwal at freescale.com
Sat Jul 4 04:41:38 CEST 2009
> -----Original Message-----
> From: Kumar Gala [mailto:galak at kernel.crashing.org]
> Sent: Thursday, July 02, 2009 7:30 PM
> To: Aggrwal Poonam-B10812
> Cc: u-boot at lists.denx.de
> Subject: Re: [U-Boot] [PATCH 5/5] P2020RDB Platform support added.
>
> >
> >
> > index acec1a0..21eb424 100644
> > --- a/Makefile
> > +++ b/Makefile
> > @@ -1,4 +1,5 @@
> > #
> > +# Copyright (C) 2009 Freescale Semiconductor, Inc. All rights
> > reserved.
> > # (C) Copyright 2000-2009
> > # Wolfgang Denk, DENX Software Engineering, wd at denx.de.
> > #
> > @@ -2491,6 +2492,13 @@ P2020DS_config: unconfig
> > fi
> > @$(MKCONFIG) -a P2020DS ppc mpc85xx p2020ds freescale
> >
> > +P2020RDB_config: unconfig
> > + @mkdir -p $(obj)include
> > + @echo "#define CONFIG_MP" >>$(obj)include/config.h ;
> > + @$(XECHO) "... setting CONFIG_MP." ;
>
> what's going on here? Why not just set CONFIG_MP in
> include/configs/ P1_P2_RDB.h
>
This is because the fiile include/configs/P1_P2_RDB.h will also support
more Silicons in future , some of which are single core as well.
> > + @echo "#define CONFIG_P2020" >>$(obj)include/config.h ;
> > + @$(MKCONFIG) -a P1_P2_RDB ppc mpc85xx p1_p2_rdb freescale
> > +
> > PM854_config: unconfig
> > @$(MKCONFIG) $(@:_config=) ppc mpc85xx pm854
> >
>
> >
> > diff --git a/board/freescale/p1_p2_rdb/p1_p2_rdb.c
> b/board/freescale/
> > p1_p2_rdb/p1_p2_rdb.c new file mode 100644 index 0000000..15520cc
> > --- /dev/null
> > +++ b/board/freescale/p1_p2_rdb/p1_p2_rdb.c
> > @@ -0,0 +1,526 @@
> > +/*
> > + * Copyright (C) 2009 Freescale Semiconductor, Inc. All rights
> > reserved.
> > + *
> > + * See file CREDITS for list of people who contributed to this
> > + * project.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation; either version 2 of
> > + * the License, or (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General
> Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> > + * MA 02111-1307 USA
> > + */
> > +
> > +#include <common.h>
> > +#include <command.h>
> > +#include <pci.h>
> > +#include <asm/processor.h>
> > +#include <asm/mmu.h>
> > +#include <asm/cache.h>
> > +#include <asm/immap_85xx.h>
> > +#include <asm/fsl_pci.h>
> > +#include <asm/fsl_ddr_sdram.h>
> > +#include <asm/io.h>
> > +#include <asm/fsl_law.h>
> > +#include <miiphy.h>
> > +#include <libfdt.h>
> > +#include <fdt_support.h>
> > +#include <tsec.h>
> > +#include <vsc7385.h>
>
> Can we split out the ddr code into ddr.c and the pci code into pci.c
>
> >
> > +
> > +
> > +#if defined(CONFIG_DDR_ECC) && !
> > defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
> > +extern void ddr_enable_ecc(unsigned int dram_size); #endif
> > +
> > +#define GPIO_DIR 0x060f0000
> > +#define BOARD_PERI_RST 0x020f0000
> > +#define USB_RST 0x08000000
> > +
> > +#define SYSCLK_MASK 0x00200000
> > +#define BOARDREV_MASK 0x10100000
> > +#define BOARDREV_B 0x10100000
> > +#define BOARDREV_C 0x00100000
> > +
> > +#define SYSCLK_66 66666666
> > +#define SYSCLK_50 50000000
> > +#define SYSCLK_100 100000000
> > +DECLARE_GLOBAL_DATA_PTR;
> > +
> > +phys_size_t fixed_sdram(void);
> > +
> > +unsigned long get_board_sys_clk(ulong dummy) {
> > + volatile ccsr_gpio_t *pgpio = (void *)
> > (CONFIG_SYS_MPC85xx_GPIO_ADDR);
> > + u32 val, sysclk, temp;
> > +
> > + val = pgpio->gpdat;
> > + sysclk = val & SYSCLK_MASK;
> > + temp = val & BOARDREV_MASK;
> > + if (temp == BOARDREV_C) {
> > + if(sysclk == 0)
> > + return SYSCLK_66;
> > + else
> > + return SYSCLK_100;
> > + } else if (temp == BOARDREV_B) {
> > + if(sysclk == 0)
> > + return SYSCLK_66;
> > + else
> > + return SYSCLK_50;
> > + }
> > +}
> > +
> > +unsigned long get_board_ddr_size(ulong dummy) {
> > + return 1024;
> > +}
> > +
> > +int board_early_init_f (void)
> > +{
> > +#ifdef CONFIG_MMC
> > + volatile ccsr_gur_t *gur = (void
> *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
> > +
> > + setbits_be32(&gur->pmuxcr,
> > + (MPC85xx_PMUXCR_SDHC_CD |
> > + MPC85xx_PMUXCR_SDHC_WP));
> > +#endif
> > + return 0;
> > +}
> > +
> > +int checkboard (void)
> > +{
> > + u32 val, temp;
> > + volatile ccsr_gpio_t *pgpio = (void *)
> > (CONFIG_SYS_MPC85xx_GPIO_ADDR);
> > + char board_rev = 0;
> > +
> > + val = pgpio->gpdat;
> > + temp = val & BOARDREV_MASK;
> > + if (temp == BOARDREV_C)
> > + board_rev = 'C';
> > + else if (temp == BOARDREV_B)
> > + board_rev = 'B';
> > +
> > + printf ("Board: %sRDB Rev%c, System ID: 0x%02x, "
> > + "System Version: 0x%02x\n", gd->cpu->name,
> > + board_rev, 0, 0);
> > +
> > +/* Bringing the following peripherals out of reset via GPIOs
> > + * 0= reset and 1= out of reset
> > + * GPIO12 - Reset to Ethernet Switch
> > + * GPIO13 - Reset to SLIC/SLAC devices
> > + * GPIO14 - Reset to SGMII_PHY_N
> > + * GPIO15 - Reset to PCIe slots
> > + * GPIO6 - Reset to RGMII PHY
> > + * GPIO5 - Reset to USB3300 devices 1= reset and 0= out of
> reset */
> > + val = pgpio->gpdir;
> > + val |= GPIO_DIR;
> > + setbits_be32(&pgpio->gpdir, GPIO_DIR);
> > +
> > + val = pgpio->gpdat;
> > + clrsetbits_be32(&pgpio->gpdat, USB_RST, BOARD_PERI_RST);
> > +
> > + return 0;
> > +}
> > +
> > +phys_size_t initdram(int board_type)
> > +{
> > + phys_size_t dram_size = 0;
> > +
> > + puts("Initializing....");
> > +
> > +#ifdef CONFIG_DDR_SPD
> > + dram_size = fsl_ddr_sdram();
> > +#else
> > + dram_size = fixed_sdram();
> > + set_ddr_laws(0, dram_size, LAW_TRGT_IF_DDR_1); #endif
> > + dram_size = setup_ddr_tlbs(dram_size / 0x100000);
> > + dram_size *= 0x100000;
> > +
> > +#if defined(CONFIG_DDR_ECC) && !
> > defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
> > + /*
> > + * Initialize and enable DDR ECC.
> > + */
> > + ddr_enable_ecc(dram_size);
> > +#endif
> > + puts(" DDR: ");
> > + return dram_size;
> > +}
> > +
> > +#if !defined(CONFIG_SPD)
> > +/*
> > + * Fixed sdram init -- doesn't use serial presence detect.
> > + */
> > +
> > +phys_size_t fixed_sdram (void)
> > +{
> > +
> > + volatile ccsr_ddr_t *ddr= (ccsr_ddr_t
> *)CONFIG_SYS_MPC85xx_DDR_ADDR;
> > + int d_init;
> > + sys_info_t sysinfo;
> > + char buf[32];
> > +
> > + ddr->cs0_bnds = CONFIG_SYS_DDR_CS0_BNDS;
> > + ddr->cs0_config = CONFIG_SYS_DDR_CS0_CONFIG;
> > + ddr->cs0_config_2 = CONFIG_SYS_DDR_CS0_CONFIG_2;
> > + ddr->sdram_data_init = CONFIG_SYS_DDR_DATA_INIT;
> > +
> > + get_sys_info(&sysinfo);
> > + printf("Configuring DDR for %s MT/s data rate\n",
> > + strmhz(buf, sysinfo.freqDDRBus));
> > +
> > + if(sysinfo.freqDDRBus <= 400000000) {
> > + /* RevB and RevC boards */
> > + ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_400;
> > + ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_400;
> > + ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_400;
> > + ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_400;
> > + ddr->timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4_400;
> > + ddr->timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5_400;
> > + ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1_400;
> > + ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_400;
> > + ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL_400;
> > + ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_400;
> > + ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL_400;
> > + ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2_400;
> > + }
> > + else if(sysinfo.freqDDRBus <= 534000000) {
> > + ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_533;
> > + ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_533;
> > + ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_533;
> > + ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_533;
> > + ddr->timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4_533;
> > + ddr->timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5_533;
> > + ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1_533;
> > + ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_533;
> > + ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL_533;
> > + ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_533;
> > + ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL_533;
> > + ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2_533;
> > + }
> > + else if(sysinfo.freqDDRBus <= 667000000) {
> > + ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_667;
> > + ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_667;
> > + ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_667;
> > + ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_667;
> > + ddr->timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4_667;
> > + ddr->timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5_667;
> > + ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1_667;
> > + ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_667;
> > + ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL_667;
> > + ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_667;
> > + ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL_667;
> > + ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2_667;
> > + }
> > + else if(sysinfo.freqDDRBus <= 800000000) {
> > + ddr->timing_cfg_3 = CONFIG_SYS_DDR_TIMING_3_800;
> > + ddr->timing_cfg_0 = CONFIG_SYS_DDR_TIMING_0_800;
> > + ddr->timing_cfg_1 = CONFIG_SYS_DDR_TIMING_1_800;
> > + ddr->timing_cfg_2 = CONFIG_SYS_DDR_TIMING_2_800;
> > + ddr->timing_cfg_4 = CONFIG_SYS_DDR_TIMING_4_800;
> > + ddr->timing_cfg_5 = CONFIG_SYS_DDR_TIMING_5_800;
> > + ddr->sdram_mode = CONFIG_SYS_DDR_MODE_1_800;
> > + ddr->sdram_mode_2 = CONFIG_SYS_DDR_MODE_2_800;
> > + ddr->sdram_interval = CONFIG_SYS_DDR_INTERVAL_800;
> > + ddr->sdram_clk_cntl = CONFIG_SYS_DDR_CLK_CTRL_800;
> > + ddr->sdram_cfg = CONFIG_SYS_DDR_CONTROL_800;
> > + ddr->sdram_cfg_2 = CONFIG_SYS_DDR_CONTROL2_800;
> > + }
> > +
> > + /*
> > + * For 8572 DDR1 erratum - DDR controller may enter
> illegal state
> > + * when operatiing in 32-bit bus mode with 4-beat bursts,
> > + * This erratum does not affect DDR3 mode, only for DDR2 mode.
> > + * need to check if this is required for P1020/P2020 also
> > + */
> > + if ((((in_be32(&ddr->sdram_cfg) >> 24) & 0x7) ==
> > SDRAM_TYPE_DDR2)
> > + && in_be32(&ddr->sdram_cfg) & 0x80000) {
> > + /* set DEBUG_1[31] */
> > + u32 temp = in_be32(&ddr->debug_1);
> > + out_be32(&ddr->debug_1, temp | 1);
> > + }
> > +
> > +#if defined (CONFIG_DDR_ECC)
> > + ddr->err_int_en = CONFIG_SYS_DDR_ERR_INT_EN;
> > + ddr->err_disable = CONFIG_SYS_DDR_ERR_DIS;
> > + ddr->err_sbe = CONFIG_SYS_DDR_SBE;
> > +#endif
> > + asm("sync;isync");
> > +
> > + udelay(500);
> > +
> > + ddr->sdram_cfg |= SDRAM_CFG_MEM_EN;
> > +
> > +#if defined(CONFIG_ECC_INIT_VIA_DDRCONTROLLER)
> > + d_init = 1;
> > + debug("DDR - 1st controller: memory initializing\n");
> > + /*
> > + * Poll until memory is initialized.
> > + * 512 Meg at 400 might hit this 200 times or so.
> > + */
> > + while ((ddr->sdram_cfg_2 & (d_init << 4)) != 0) {
> > + udelay(1000);
> > + }
> > + debug("DDR: memory initialized\n\n");
> > + asm("sync; isync");
> > + udelay(500);
> > +#endif
> > +
> > + return CONFIG_SYS_SDRAM_SIZE * 1024 * 1024; }
> > +
> > +#endif
> > +
> > +#ifdef CONFIG_PCIE1
> > +static struct pci_controller pcie1_hose; #endif
> > +
> > +#ifdef CONFIG_PCIE2
> > +static struct pci_controller pcie2_hose; #endif
> > +
> > +int first_free_busno=0;
> > +#ifdef CONFIG_PCI
> > +void pci_init_board(void)
> > +{
> > + volatile ccsr_gur_t *gur = (void
> *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
> > + uint devdisr = gur->devdisr;
> > + uint io_sel = (gur->pordevsr & MPC85xx_PORDEVSR_IO_SEL) >> 19;
> > + uint host_agent = (gur->porbmsr & MPC85xx_PORBMSR_HA) >> 16;
> > +
> > + volatile ccsr_fsl_pci_t *pci;
> > + struct pci_controller *hose;
> > + int pcie_ep, pcie_configured;
> > + struct pci_region *r;
> > +/* u32 temp32; */
>
> remove this since its not used
>
> >
> > +
> > + debug (" pci_init_board: devdisr=%x, io_sel=%x,
> host_agent=%x\n",
> > + devdisr, io_sel, host_agent);
> > +
> > + if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII2_DIS))
> > + printf (" eTSEC2 is in sgmii mode.\n");
> > +
> > +#ifdef CONFIG_PCIE2
> > + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE2_ADDR;
> > + hose = &pcie2_hose;
> > + pcie_ep = (host_agent == 2) || (host_agent == 4) ||
> > + (host_agent == 6) || (host_agent == 0);
> > + pcie_configured = (io_sel == 0xE);
> > + r = hose->regions;
> > +
> > + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
> > + printf ("\n PCIE2 connected to Slot 1 as %s
> (base address %x)",
> > + pcie_ep ? "End Point" : "Root Complex",
> > + (uint)pci);
> > + if (pci->pme_msg_det) {
> > + pci->pme_msg_det = 0xffffffff;
> > + debug (" with errors. Clearing. Now
> 0x%08x",pci->pme_msg_det);
> > + }
> > + printf ("\n");
> > +
> > + /* inbound */
> > + r += fsl_pci_setup_inbound_windows(r);
> > +
> > + /* outbound memory */
> > + pci_set_region(r++,
> > + CONFIG_SYS_PCIE2_MEM_BUS,
> > + CONFIG_SYS_PCIE2_MEM_PHYS,
> > + CONFIG_SYS_PCIE2_MEM_SIZE,
> > + PCI_REGION_MEM);
> > +
> > + /* outbound io */
> > + pci_set_region(r++,
> > + CONFIG_SYS_PCIE2_IO_BUS,
> > + CONFIG_SYS_PCIE2_IO_PHYS,
> > + CONFIG_SYS_PCIE2_IO_SIZE,
> > + PCI_REGION_IO);
> > +
> > + hose->region_count = r - hose->regions;
> > + hose->first_busno=first_free_busno;
> > + pci_setup_indirect(hose, (int) &pci->cfg_addr,
> (int) &pci-
> > >cfg_data);
> > +
> > + fsl_pci_init(hose);
> > + first_free_busno=hose->last_busno+1;
> > + printf (" PCIE2 on bus %02x - %02x\n",
> > + hose->first_busno,hose->last_busno);
> > +
> > + } else {
> > + printf (" PCIE2: disabled\n");
> > + }
> > +#else
> > + gur->devdisr |= MPC85xx_DEVDISR_PCIE2; /* disable */
> #endif #ifdef
> > +CONFIG_PCIE1
> > + pci = (ccsr_fsl_pci_t *) CONFIG_SYS_PCIE1_ADDR;
> > + hose = &pcie1_hose;
> > + pcie_ep = (host_agent <= 1) || (host_agent == 4) ||
> > + (host_agent == 5);
> > + pcie_configured = (io_sel == 0xE);
> > + r = hose->regions;
> > +
> > + if (pcie_configured && !(devdisr & MPC85xx_DEVDISR_PCIE)){
> > + printf ("\n PCIE1 connected to Slot 2 as %s
> (base address %x)",
> > + pcie_ep ? "End Point" : "Root Complex",
> > + (uint)pci);
> > + if (pci->pme_msg_det) {
> > + pci->pme_msg_det = 0xffffffff;
> > + debug (" with errors. Clearing. Now
> 0x%08x",pci->pme_msg_det);
> > + }
> > + printf ("\n");
> > +
> > + /* inbound */
> > + r += fsl_pci_setup_inbound_windows(r);
> > +
> > + /* outbound memory */
> > + pci_set_region(r++,
> > + CONFIG_SYS_PCIE1_MEM_BUS,
> > + CONFIG_SYS_PCIE1_MEM_PHYS,
> > + CONFIG_SYS_PCIE1_MEM_SIZE,
> > + PCI_REGION_MEM);
> > +
> > + /* outbound io */
> > + pci_set_region(r++,
> > + CONFIG_SYS_PCIE1_IO_BUS,
> > + CONFIG_SYS_PCIE1_IO_PHYS,
> > + CONFIG_SYS_PCIE1_IO_SIZE,
> > + PCI_REGION_IO);
> > +
> > + hose->region_count = r - hose->regions;
> > + hose->first_busno=first_free_busno;
> > +
> > + pci_setup_indirect(hose, (int) &pci->cfg_addr,
> (int) &pci-
> > >cfg_data);
> > +
> > + fsl_pci_init(hose);
> > +
> > + first_free_busno=hose->last_busno+1;
> > + printf(" PCIE1 on bus %02x - %02x\n",
> > + hose->first_busno,hose->last_busno);
> > +
> > + } else {
> > + printf (" PCIE1: disabled\n");
> > + }
> > +#else
> > + gur->devdisr |= MPC85xx_DEVDISR_PCIE; /* disable */
> #endif } #endif
> > +
> > +int board_early_init_r(void)
> > +{
> > + const unsigned int flashbase = CONFIG_SYS_FLASH_BASE;
> > + const u8 flash_esel = 2;
> > +
> > + /*
> > + * Remap Boot flash region to caching-inhibited
> > + * so that flash can be erased properly.
> > + */
> > +
> > + /* Flush d-cache and invalidate i-cache of any FLASH data */
> > + flush_dcache();
> > + invalidate_icache();
> > +
> > + /* invalidate existing TLB entry for flash */
> > + disable_tlb(flash_esel);
> > +
> > + set_tlb(1, flashbase, CONFIG_SYS_FLASH_BASE_PHYS,
> /* tlb, epn, rpn
> > */
> > + MAS3_SX|MAS3_SW|MAS3_SR, MAS2_I|MAS2_G,
> /* perms, wimge */
> > + 0, flash_esel, BOOKE_PAGESZ_16M, 1);
> /* ts, esel, tsize, iprot */
> > + return 0;
> > +}
> > +
> > +
> > +#ifdef CONFIG_TSEC_ENET
> > +int board_eth_init(bd_t *bis)
> > +{
> > + struct tsec_info_struct tsec_info[4];
> > + volatile ccsr_gur_t *gur = (void
> *)(CONFIG_SYS_MPC85xx_GUTS_ADDR);
> > + int num = 0;
> > +
> > +#ifdef CONFIG_TSEC1
> > + SET_STD_TSEC_INFO(tsec_info[num], 1);
> > + num++;
> > +#endif
> > +#ifdef CONFIG_TSEC2
> > + SET_STD_TSEC_INFO(tsec_info[num], 2);
> > + num++;
> > +#endif
> > +#ifdef CONFIG_TSEC3
> > + SET_STD_TSEC_INFO(tsec_info[num], 3);
> > + if (!(gur->pordevsr & MPC85xx_PORDEVSR_SGMII3_DIS))
> > + tsec_info[num].flags |= TSEC_SGMII;
> > + num++;
> > +#endif
> > +
> > + if (!num) {
> > + printf("No TSECs initialized\n");
> > +
> > + return 0;
> > + }
> > +
> > + tsec_eth_init(bis, tsec_info, num);
> > +
> > + return 0;
>
> change to return pci_eth_init(bis);
>
> >
> > +}
> > +#endif
> > +
> > +/*
> > + * Miscellaneous late-boot configurations
> > + *
> > + * If a VSC7385 microcode image is present, then upload it.
> > +*/
> > +int misc_init_r(void)
> > +{
> > + int rc = 0;
> > +
> > +
> > +#ifdef CONFIG_VSC7385_IMAGE
> > + printf(" uploading VSC7385 microcode.from %x\n",
> > CONFIG_VSC7385_IMAGE);
> > + if (vsc7385_upload_firmware((void *) CONFIG_VSC7385_IMAGE,
> > + CONFIG_VSC7385_IMAGE_SIZE)) {
> > + puts("Failure uploading VSC7385 microcode.\n");
> > + rc = 1;
> > + }
> > +#endif
> > +
> > + return rc;
> > +}
> > +
> > +#if defined(CONFIG_OF_BOARD_SETUP)
> > +void ft_board_setup(void *blob, bd_t *bd) {
> > + ulong base, size;
>
> these need to be:
> phys_addr_t base;
> phys_size_t size;
>
> >
> > +
> > + ft_cpu_setup(blob, bd);
> > +
> > + base = getenv_bootm_low();
> > + size = getenv_bootm_size();
> > +
> > + fdt_fixup_memory(blob, (u64)base, (u64)size);
> > +
> > +#ifdef CONFIG_PCIE2
> > + ft_fsl_pci_setup(blob, "pci1", &pcie2_hose); #endif #ifdef
> > +CONFIG_PCIE1
> > + ft_fsl_pci_setup(blob, "pci2", &pcie1_hose); #endif } #endif
> > +
> > +#ifdef CONFIG_MP
> > +extern void cpu_mp_lmb_reserve(struct lmb *lmb);
> > +
> > +void board_lmb_reserve(struct lmb *lmb) {
> > + cpu_mp_lmb_reserve(lmb);
> > +}
> > +#endif
>
>
> > diff --git a/include/configs/P1_P2_RDB.h
> b/include/configs/P1_P2_RDB.h
> > new file mode 100644 index 0000000..f740db5
> > --- /dev/null
> > +++ b/include/configs/P1_P2_RDB.h
> > @@ -0,0 +1,623 @@
> > +/*
> > + * Copyright (C) 2009 Freescale Semiconductor, Inc. All rights
> > reserved.
> > + *
> > + * See file CREDITS for list of people who contributed to this
> > + * project.
> > + *
> > + * This program is free software; you can redistribute it and/or
> > + * modify it under the terms of the GNU General Public License as
> > + * published by the Free Software Foundation; either version 2 of
> > + * the License, or (at your option) any later version.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + *
> > + * You should have received a copy of the GNU General
> Public License
> > + * along with this program; if not, write to the Free Software
> > + * Foundation, Inc., 59 Temple Place, Suite 330, Boston,
> > + * MA 02111-1307 USA
> > + */
> > +
> > +/*
> > + * P1 P2 RDB board configuration file
> > + * This file is intends to address a set of Low End and
> Ultra Low End
> > + * Freescale SOCs of QorIQ series(RDB platforms).
> > + * Currently only P2020RDB
> > + *
> > + */
> > +#ifndef __CONFIG_H
> > +#define __CONFIG_H
> > +
> > +/* High Level Configuration Options */
> > +#define CONFIG_BOOKE 1 /* BOOKE */
> > +#define CONFIG_E500 1 /* BOOKE e500 family */
> > +#define CONFIG_MPC85xx 1 /*
> MPC8540/60/55/41/48/P1020/P2020, etc */
> > +#define CONFIG_FSL_ELBC 1 /* Enable eLBC Support */
> > +#define CONFIG_PCI 1 /* Enable PCI/PCIE */
> > +#define CONFIG_PCIE1 1 /* PCIE
> controler 1 (slot 1) */
> > +#define CONFIG_PCIE2 1 /* PCIE
> controler 2 (slot 2) */
> > +#define CONFIG_FSL_PCI_INIT 1 /* Use common
> FSL init code */
> > +#define CONFIG_FSL_PCIE_RESET 1 /* need PCIe
> reset errata */
> > +#define CONFIG_SYS_PCI_64BIT 1 /* enable
> 64-bit PCI resources */
> > +#define CONFIG_FSL_LAW 1 /* Use common
> FSL init code */
> > +#define CONFIG_TSEC_ENET /* tsec ethernet support */
> > +#define CONFIG_ENV_OVERWRITE
> > +
> > +
> > +#define CONFIG_SYS_CLK_FREQ get_board_sys_clk(0)
> /*sysclk for P1_P2
> > RDB */
> > +#define CONFIG_DDR_CLK_FREQ 66666666 /* DDRCLK on
> P1_P2 RDB */
> > +
> > +/*
> > + * These can be toggled for performance analysis, otherwise use
> > default.
> > + */
> > +#define CONFIG_L2_CACHE /* toggle L2 cache */
> > +#define CONFIG_BTB /* toggle branch predition */
> > +
> > +#define CONFIG_BOARD_EARLY_INIT_F 1 /* Call
> board_pre_init */
> > +
> > +#define CONFIG_ADDR_STREAMING /* toggle addr
> streaming */
> > +
> > +#define CONFIG_ENABLE_36BIT_PHYS 1
> > +
> > +#define CONFIG_SYS_MEMTEST_START 0x00000000 /*
> memtest works on */
> > +#define CONFIG_SYS_MEMTEST_END 0x1fffffff
> > +#define CONFIG_PANIC_HANG /* do not reset board on panic */
> > +
> > +/*
> > + * Base addresses -- Note these are effective addresses where the
> > + * actual resources get mapped (not physical addresses) */
> > +#define CONFIG_SYS_CCSRBAR_DEFAULT 0xff700000 /*
> CCSRBAR Default */
> > +#define CONFIG_SYS_CCSRBAR 0xffe00000 /*
> relocated CCSRBAR */
> > +#define CONFIG_SYS_CCSRBAR_PHYS CONFIG_SYS_CCSRBAR
> /* physical addr
> > of CCSRBAR */
> > +#define CONFIG_SYS_IMMR CONFIG_SYS_CCSRBAR
> /* PQII uses
> > CONFIG_SYS_IMMR */
> > +
> > +#define CONFIG_SYS_PCIE2_ADDR
> (CONFIG_SYS_CCSRBAR+0x9000)
> > +#define CONFIG_SYS_PCIE1_ADDR
> (CONFIG_SYS_CCSRBAR+0xa000)
> > +
> > +/* DDR Setup */
> > +#define CONFIG_FSL_DDR2
> > +#undef CONFIG_FSL_DDR_INTERACTIVE
> > +#undef CONFIG_SPD_EEPROM /* Use SPD EEPROM for
> DDR setup */
> > +/* on the board */
> > +#undef CONFIG_DDR_DLL
> > +
> > +#define CONFIG_MEM_INIT_VALUE 0xDeadBeef
> > +
> > +#define CONFIG_SYS_SDRAM_SIZE get_board_ddr_size(0)
> > +#define CONFIG_SYS_DDR_SDRAM_BASE 0x00000000
> > +#define CONFIG_SYS_SDRAM_BASE
> CONFIG_SYS_DDR_SDRAM_BASE
> > +
> > +#define CONFIG_NUM_DDR_CONTROLLERS 1
> > +#define CONFIG_DIMM_SLOTS_PER_CTLR 1
> > +#define CONFIG_CHIP_SELECTS_PER_CTRL 1
> > +
> > +/* These are used when DDR doesn't use SPD. */
> > +/* DDR2 at 533MHz, 512MB */
> > +#define CONFIG_SYS_DDR_CS0_BNDS 0x0000003F
> > +#define CONFIG_SYS_DDR_CS0_CONFIG 0x80014202 /* Enable, no
> > interleaving */
> > +#define CONFIG_SYS_DDR_CS0_CONFIG_2 0x00000000
> > +
> > +#define CONFIG_SYS_DDR_TIMING_3_533 0x00020000
> > +#define CONFIG_SYS_DDR_TIMING_0_533 0x00260802
> > +#define CONFIG_SYS_DDR_TIMING_1_533 0x4c47c432
> > +#define CONFIG_SYS_DDR_TIMING_2_533 0x0f9848ce
> > +#define CONFIG_SYS_DDR_TIMING_4_533 0x00000000
> > +#define CONFIG_SYS_DDR_TIMING_5_533 0x00000000
> > +#define CONFIG_SYS_DDR_CLK_CTRL_533 0x02800000
> > +#define CONFIG_SYS_DDR_MODE_1_533 0x00040642
> > +#define CONFIG_SYS_DDR_MODE_2_533 0x00000000
> > +#define CONFIG_SYS_DDR_INTERVAL_533 0x08200100
> > +#define CONFIG_SYS_DDR_CONTROL_533 0x43000000
> /* Type = DDR2 */
> > +#define CONFIG_SYS_DDR_CONTROL2_533 0x24401000
> > +
> > +
> > +#define CONFIG_SYS_DDR_TIMING_3_400 0x00010000
> > +#define CONFIG_SYS_DDR_TIMING_0_400 0x00260802
> > +#define CONFIG_SYS_DDR_TIMING_1_400 0x39355322
> > +#define CONFIG_SYS_DDR_TIMING_2_400 0x1f9048ca
> > +#define CONFIG_SYS_DDR_TIMING_4_400 0x00000000
> > +#define CONFIG_SYS_DDR_TIMING_5_400 0x00000000
> > +#define CONFIG_SYS_DDR_CLK_CTRL_400 0x02800000
> > +#define CONFIG_SYS_DDR_MODE_1_400 0x00480432
> > +#define CONFIG_SYS_DDR_MODE_2_400 0x00000000
> > +#define CONFIG_SYS_DDR_INTERVAL_400 0x06180100
> > +#define CONFIG_SYS_DDR_CONTROL_400 0x43000000
> /* Type = DDR2 */
> > +#define CONFIG_SYS_DDR_CONTROL2_400 0x24401000
> > +
> > +
> > +#define CONFIG_SYS_DDR_TIMING_3_667 0x00030000
> > +#define CONFIG_SYS_DDR_TIMING_0_667 0x55770802
> > +#define CONFIG_SYS_DDR_TIMING_1_667 0x5f599543
> > +#define CONFIG_SYS_DDR_TIMING_2_667 0x0fa074d1
> > +#define CONFIG_SYS_DDR_TIMING_4_667 0x00000000
> > +#define CONFIG_SYS_DDR_TIMING_5_667 0x00000000
> > +#define CONFIG_SYS_DDR_CLK_CTRL_667 0x02800000
> > +#define CONFIG_SYS_DDR_MODE_1_667 0x00040852
> > +#define CONFIG_SYS_DDR_MODE_2_667 0x00000000
> > +#define CONFIG_SYS_DDR_INTERVAL_667 0x0a280100
> > +#define CONFIG_SYS_DDR_CONTROL_667 0x43000000
> /* Type = DDR2 */
> > +#define CONFIG_SYS_DDR_CONTROL2_667 0x24401000
> > +
> > +#define CONFIG_SYS_DDR_TIMING_3_800 0x00040000
> > +#define CONFIG_SYS_DDR_TIMING_0_800 0x55770802
> > +#define CONFIG_SYS_DDR_TIMING_1_800 0x6f6b6543
> > +#define CONFIG_SYS_DDR_TIMING_2_800 0x0fa074d1
> > +#define CONFIG_SYS_DDR_TIMING_4_800 0x00000000
> > +#define CONFIG_SYS_DDR_TIMING_5_800 0x00000000
> > +#define CONFIG_SYS_DDR_CLK_CTRL_800 0x02000000
> > +#define CONFIG_SYS_DDR_MODE_1_800 0x00440862
> > +#define CONFIG_SYS_DDR_MODE_2_800 0x00000000
> > +#define CONFIG_SYS_DDR_INTERVAL_800 0x0a280100
> > +#define CONFIG_SYS_DDR_CONTROL_800
> 0x43000000 /* Type = DDR2 */
> > +#define CONFIG_SYS_DDR_CONTROL2_800 0x24401000
> > +
> > +#define CONFIG_SYS_DDR_DATA_INIT 0xdeadbeef
> > +#define CONFIG_SYS_DDR_OCD_CTRL 0x00000000
> > +#define CONFIG_SYS_DDR_OCD_STATUS 0x00000000
> > +
> > +#define CONFIG_SYS_DDR_ERR_INT_EN 0x0000000d
> > +#define CONFIG_SYS_DDR_ERR_DIS 0x00000000
> > +#define CONFIG_SYS_DDR_SBE 0x00FF0000
> > +
> > +#define CONFIG_SYS_DDR_TLB_START 9
> > +
> > +#undef CONFIG_CLOCKS_IN_MHZ
> > +
> > +/*
> > + * Memory map
> > + *
> > + * 0x0000_0000 0x3fff_ffff DDR
> 1G cacheablen
> > + * 0xa000_0000 0xbfff_ffff PCI Express Mem
> 1G non-cacheable
> > + * 0xffc2_0000 0xffc5_ffff PCI IO range
> 256K non-cacheable
> > + *
> > + * Localbus cacheable (TBD)
> > + * 0xXXXX_XXXX 0xXXXX_XXXX SRAM
> YZ M Cacheable
> > + *
> > + * Localbus non-cacheable
> > + * 0xef00_0000 0xefff_ffff FLASH
> 16M non-cacheable
> > + * 0xffa0_0000 0xffaf_ffff NAND
> 1M non-cacheable
> > + * 0xffb0_0000 0xffbf_ffff VSC7385 switch
> 1M non-cacheable
> > + * 0xffd0_0000 0xffd0_3fff L1 for stack
> 16K Cacheable TLB0
> > + * 0xffe0_0000 0xffef_ffff CCSR
> 1M non-cacheable
> > + */
> > +
> > +/*
> > + * Local Bus Definitions
> > + */
> > +#define CONFIG_SYS_FLASH_BASE 0xef000000
> /* start of FLASH 16M */
> > +
> > +#define CONFIG_SYS_FLASH_BASE_PHYS CONFIG_SYS_FLASH_BASE
> > +
> > +#define CONFIG_FLASH_BR_PRELIM
> > (BR_PHYS_ADDR(CONFIG_SYS_FLASH_BASE_PHYS) | BR_PS_16 | BR_V)
> > +#define CONFIG_FLASH_OR_PRELIM 0xff000ff7
>
> We have OR_ bitmasks
>
> >
> > +
> > +#define CONFIG_SYS_FLASH_BANKS_LIST {CONFIG_SYS_FLASH_BASE}
> > +#define CONFIG_SYS_FLASH_QUIET_TEST
> > +#define CONFIG_FLASH_SHOW_PROGRESS 45 /* count down from 45/5: 9..1
> > */
> > +
> > +#define CONFIG_SYS_MAX_FLASH_BANKS 1 /*
> number of banks */
> > +#define CONFIG_SYS_MAX_FLASH_SECT 128 /*
> sectors per device */
> > +#undef CONFIG_SYS_FLASH_CHECKSUM
> > +#define CONFIG_SYS_FLASH_ERASE_TOUT 60000
> /* Flash Erase Timeout
> > (ms) */
> > +#define CONFIG_SYS_FLASH_WRITE_TOUT 500
> /* Flash Write Timeout
> > (ms) */
> > +
> > +#define CONFIG_SYS_MONITOR_BASE TEXT_BASE /*
> start of monitor */
> > +
> > +#define CONFIG_FLASH_CFI_DRIVER
> > +#define CONFIG_SYS_FLASH_CFI
> > +#define CONFIG_SYS_FLASH_EMPTY_INFO
> > +#define CONFIG_SYS_FLASH_AMD_CHECK_DQ7
> > +
> > +#define CONFIG_BOARD_EARLY_INIT_R /* call board_early_init_r
> > function */
> > +
> > +
> > +#define CONFIG_SYS_INIT_RAM_LOCK 1
> > +#define CONFIG_SYS_INIT_RAM_ADDR 0xffd00000 /*
> stack in RAM */
>
> fix whitespace
>
> >
> > +#define CONFIG_SYS_INIT_RAM_END 0x00004000 /* End
> of used area in
> > RAM */
> > +
> > +#define CONFIG_SYS_GBL_DATA_SIZE 128 /* num bytes
> initial data */
> > +#define CONFIG_SYS_GBL_DATA_OFFSET (CONFIG_SYS_INIT_RAM_END -
> > CONFIG_SYS_GBL_DATA_SIZE)
> > +#define CONFIG_SYS_INIT_SP_OFFSET CONFIG_SYS_GBL_DATA_OFFSET
> > +
> > +#define CONFIG_SYS_MONITOR_LEN (256 * 1024) /*
> Reserve 256 kB for
> > Mon */
> > +#define CONFIG_SYS_MALLOC_LEN (1024 * 1024)
> /* Reserved for malloc
> > */
> > +
> > +#define CONFIG_SYS_NAND_BASE 0xffa00000
> > +#define CONFIG_SYS_NAND_BASE_PHYS CONFIG_SYS_NAND_BASE
> > +#define CONFIG_SYS_NAND_BASE_LIST {CONFIG_SYS_NAND_BASE}
> > +#define CONFIG_SYS_MAX_NAND_DEVICE 1
> > +#define NAND_MAX_CHIPS 1
> > +#define CONFIG_MTD_NAND_VERIFY_WRITE
> > +#define CONFIG_CMD_NAND 1
> > +#define CONFIG_NAND_FSL_ELBC 1
> > +#define CONFIG_SYS_NAND_BLOCK_SIZE (16 * 1024)
> > +
> > +/* NAND flash config */
> > +#define CONFIG_NAND_BR_PRELIM (CONFIG_SYS_NAND_BASE_PHYS \
> > + | (2<<BR_DECC_SHIFT) /* Use
> HW ECC */ \
> > + | BR_PS_8 /* Port
> Size = 8 bit */ \
> > + | BR_MS_FCM /* MSEL
> = FCM */ \
> > + | BR_V) /* valid */
> > +
> > +#define CONFIG_NAND_OR_PRELIM (0xFFF80000
> /* length 32K */ \
> > + | OR_FCM_CSCT \
> > + | OR_FCM_CST \
> > + | OR_FCM_CHT \
> > + | OR_FCM_SCY_1 \
> > + | OR_FCM_TRLX \
> > + | OR_FCM_EHTR)
> > +
> > +#define CONFIG_SYS_BR0_PRELIM CONFIG_FLASH_BR_PRELIM /* NOR Base
> > Address */
> > +#define CONFIG_SYS_OR0_PRELIM CONFIG_FLASH_OR_PRELIM /* NOR
> > Options */
> > +#define CONFIG_SYS_BR1_PRELIM CONFIG_NAND_BR_PRELIM /* NAND Base
> > Address */
> > +#define CONFIG_SYS_OR1_PRELIM CONFIG_NAND_OR_PRELIM /* NAND
> > Options */
> > +
> > +#define CONFIG_SYS_VSC7385_BASE 0xffb00000
> > +
> > +#define CONFIG_SYS_VSC7385_BASE_PHYS CONFIG_SYS_VSC7385_BASE
> > +
> > +#define CONFIG_SYS_BR2_PRELIM
> (CONFIG_SYS_VSC7385_BASE | BR_PS_8 |
> > BR_V) /* VSC7385 switch */
> > +#define CONFIG_SYS_OR2_PRELIM (OR_AM_128KB | OR_GPCM_CSNT |
> > OR_GPCM_XACS | \
> > + OR_GPCM_SCY_15 | OR_GPCM_SETA |
> OR_GPCM_TRLX | \
> > + OR_GPCM_EHTR | OR_GPCM_EAD)
> > +
> > +/* Serial Port - controlled on board with jumper J8
> > + * open - index 2
> > + * shorted - index 1
> > + */
> > +#define CONFIG_CONS_INDEX 1
> > +//#define CONFIG_CONS_INDEX 2
> > +#undef CONFIG_SERIAL_SOFTWARE_FIFO
> > +#define CONFIG_SYS_NS16550
> > +#define CONFIG_SYS_NS16550_SERIAL
> > +#define CONFIG_SYS_NS16550_REG_SIZE 1
> > +#define CONFIG_SYS_NS16550_CLK get_bus_freq(0)
> > +
> > +#define CONFIG_SERIAL_MULTI 1 /* Enable both serial ports */
> > +#define CONFIG_SYS_CONSOLE_IS_IN_ENV /* determine
> from environment */
> > +
> > +#define CONFIG_SYS_BAUDRATE_TABLE \
> > + {300, 600, 1200, 2400, 4800, 9600, 19200, 38400,115200}
> > +
> > +#define CONFIG_SYS_NS16550_COM1 (CONFIG_SYS_CCSRBAR+0x4500)
> > +#define CONFIG_SYS_NS16550_COM2 (CONFIG_SYS_CCSRBAR+0x4600)
> > +
> > +/* Use the HUSH parser */
> > +#define CONFIG_SYS_HUSH_PARSER
> > +#ifdef CONFIG_SYS_HUSH_PARSER
> > +#define CONFIG_SYS_PROMPT_HUSH_PS2 "> "
> > +#endif
> > +
> > +/*
> > + * Pass open firmware flat tree
> > + */
> > +#define CONFIG_OF_LIBFDT 1
> > +#define CONFIG_OF_BOARD_SETUP 1
> > +#define CONFIG_OF_STDOUT_VIA_ALIAS 1
> > +
> > +#define CONFIG_SYS_64BIT_VSPRINTF 1
> > +#define CONFIG_SYS_64BIT_STRTOUL 1
> > +
> > +/* new uImage format support */
> > +#define CONFIG_FIT 1
> > +#define CONFIG_FIT_VERBOSE 1 /* enable
> fit_format_{error,warning}()
> > */
> > +
> > +/* I2C */
> > +#define CONFIG_FSL_I2C /* Use FSL common I2C driver */
> > +#define CONFIG_HARD_I2C /* I2C with hardware support */
> > +#undef CONFIG_SOFT_I2C /* I2C bit-banged */
> > +#define CONFIG_I2C_MULTI_BUS
> > +#define CONFIG_I2C_CMD_TREE
> > +#define CONFIG_SYS_I2C_SPEED 400000 /* I2C
> speed and slave address
> > */
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
> > +#define CONFIG_SYS_I2C_SLAVE 0x7F
> > +#define CONFIG_SYS_I2C_NOPROBES {{0,0x29}}/* Don't probe these
> > addrs */
> > +#define CONFIG_SYS_I2C_OFFSET 0x3000
> > +#define CONFIG_SYS_I2C2_OFFSET 0x3100
> > +
> > +/*
> > + * I2C2 EEPROM
> > + */
> > +#define CONFIG_ID_EEPROM
> > +#ifdef CONFIG_ID_EEPROM
> > +#define CONFIG_SYS_I2C_EEPROM_NXID
> > +#endif
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR 0x57
> > +#define CONFIG_SYS_I2C_EEPROM_ADDR_LEN 1
> > +#define CONFIG_SYS_EEPROM_BUS_NUM 1
> > +
> > +//#define CONFIG_RTC_DS1337
> > +/*
> > + * General PCI
> > + * Memory space is mapped 1-1, but I/O space must start from 0.
> > + */
> > +
> > +/* controller 2, Slot 2, tgtid 2, Base address 9000 */
> > +#define CONFIG_SYS_PCIE2_MEM_VIRT 0xa0000000
> > +#define CONFIG_SYS_PCIE2_MEM_BUS 0xa0000000
> > +#define CONFIG_SYS_PCIE2_MEM_PHYS 0xa0000000
> > +#define CONFIG_SYS_PCIE2_MEM_SIZE 0x20000000 /* 512M */
> > +#define CONFIG_SYS_PCIE2_IO_VIRT 0xffc20000
> > +#define CONFIG_SYS_PCIE2_IO_BUS 0x00000000
> > +#define CONFIG_SYS_PCIE2_IO_PHYS 0xffc20000
> > +#define CONFIG_SYS_PCIE2_IO_SIZE 0x00010000 /* 64k */
> > +
> > +/* controller 1, Slot 1, tgtid 1, Base address a000 */
> > +#define CONFIG_SYS_PCIE1_MEM_VIRT 0xc0000000
> > +#define CONFIG_SYS_PCIE1_MEM_BUS 0xc0000000
> > +#define CONFIG_SYS_PCIE1_MEM_PHYS 0xc0000000
> > +#define CONFIG_SYS_PCIE1_MEM_SIZE 0x20000000 /* 512M */
> > +#define CONFIG_SYS_PCIE1_IO_VIRT 0xffc30000
> > +#define CONFIG_SYS_PCIE1_IO_BUS 0x00000000
> > +#define CONFIG_SYS_PCIE1_IO_PHYS 0xffc30000
> > +#define CONFIG_SYS_PCIE1_IO_SIZE 0x00010000 /* 64k */
> > +
> > +#if defined(CONFIG_PCI)
> > +#define CONFIG_NET_MULTI
> > +#define CONFIG_PCI_PNP /* do pci
> plug-and-play */
> > +
> > +#undef CONFIG_EEPRO100
> > +#undef CONFIG_TULIP
> > +#undef CONFIG_RTL8139
> > +
> > +#ifdef CONFIG_RTL8139
> > +/* This macro is used by RTL8139 but not defined in PPC
> > architecture */
> > +#define KSEG1ADDR(x) (x)
> > +#define _IO_BASE 0x00000000
>
> I think Timur posted a patch to remove this
> >
> > +#endif
> > +
> > +
> > +#define CONFIG_PCI_SCAN_SHOW /* show pci
> devices on startup */
> > +#define CONFIG_DOS_PARTITION
> > +
> > +#endif /* CONFIG_PCI */
> > +
> > +#define CONFIG_MISC_INIT_R
> > +
> > +/************************************************************
> > + * USB support
> > + ************************************************************/
> > +
> > +#define CONFIG_CMD_FAT
> > +#define CONFIG_CMD_EXT2
> > +#define CONFIG_CMD_USB
> > +#define CONFIG_USB_STORAGE
> > +#define CONFIG_USB_EHCI
> > +#define CONFIG_USB_EHCI_FSL
> > +#define CONFIG_EHCI_HCD_INIT_AFTER_RESET
> > +
> > +#if defined(CONFIG_TSEC_ENET)
> > +
> > +#ifndef CONFIG_NET_MULTI
> > +#define CONFIG_NET_MULTI 1
> > +#endif
> > +
> > +#define CONFIG_MII 1 /* MII PHY management */
> > +#define CONFIG_MII_DEFAULT_TSEC 1 /* Allow
> unregistered phys */
> > +#define CONFIG_TSEC1 1
> > +#define CONFIG_TSEC1_NAME "eTSEC1"
> > +#define CONFIG_TSEC2 1
> > +#define CONFIG_TSEC2_NAME "eTSEC2"
> > +#define CONFIG_TSEC3 1
> > +#define CONFIG_TSEC3_NAME "eTSEC3"
> > +
> > +#define TSEC1_PHY_ADDR 2
> > +#define TSEC2_PHY_ADDR 0
> > +#define TSEC3_PHY_ADDR 1
> > +
> > +#define CONFIG_VSC7385_ENET
> > +
> > +#define TSEC1_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
> > +#define TSEC2_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
> > +#define TSEC3_FLAGS (TSEC_GIGABIT | TSEC_REDUCED)
> > +
> > +#define TSEC1_PHYIDX 0
> > +#define TSEC2_PHYIDX 0
> > +#define TSEC3_PHYIDX 0
> > +
> > +/* Vitesse 7385 */
> > +
> > +#ifdef CONFIG_VSC7385_ENET
> > +
> > +/* The flash address and size of the VSC7385 firmware image */
> > +#define CONFIG_VSC7385_IMAGE 0xEF000000
> > +#define CONFIG_VSC7385_IMAGE_SIZE 8192
> > +
> > +#endif
> > +#define CONFIG_ETHPRIME "eTSEC1"
> > +
> > +#define CONFIG_PHY_GIGE 1 /* Include GbE
> speed/duplex detection */
> > +#endif /* CONFIG_TSEC_ENET */
> > +
> > +/*
> > + * Environment
> > + */
> > +#define CONFIG_ENV_IS_IN_FLASH 1
> > +#if CONFIG_SYS_MONITOR_BASE > 0xfff80000
> > +#define CONFIG_ENV_ADDR 0xfff80000
> > +#else
> > +#define CONFIG_ENV_ADDR (CONFIG_SYS_MONITOR_BASE -
> > CONFIG_ENV_SECT_SIZE)
> > +#endif
> > +#define CONFIG_ENV_SIZE 0x2000
> > +#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K (one sector) */
> > +
> > +#define CONFIG_LOADS_ECHO 1 /* echo on for serial
> download */
> > +#define CONFIG_SYS_LOADS_BAUD_CHANGE 1 /*
> allow baudrate change */
> > +
> > +/*
> > + * Command line configuration.
> > + */
> > +#include <config_cmd_default.h>
> > +
> > +#define CONFIG_CMD_IRQ
> > +#define CONFIG_CMD_PING
> > +#define CONFIG_CMD_I2C
> > +#define CONFIG_CMD_MII
> > +#define CONFIG_CMD_ELF
> > +#define CONFIG_CMD_IRQ
> > +#define CONFIG_CMD_SETEXPR
> > +
> > +#if defined(CONFIG_PCI)
> > +#define CONFIG_CMD_PCI
> > +#define CONFIG_CMD_BEDBUG
> > +#define CONFIG_CMD_NET
> > +#endif
> > +
> > +#undef CONFIG_WATCHDOG /* watchdog disabled */
> > +
> > +#define CONFIG_MMC 1
> > +
> > +#ifdef CONFIG_MMC
> > +#define CONFIG_FSL_ESDHC
> > +#define CONFIG_SYS_FSL_ESDHC_ADDR CONFIG_SYS_MPC85xx_ESDHC_ADDR
> > +#define CONFIG_CMD_MMC
> > +#define CONFIG_GENERIC_MMC
> > +#define CONFIG_CMD_EXT2
> > +#define CONFIG_CMD_FAT
> > +#define CONFIG_DOS_PARTITION
> > +#ifdef CONFIG_P2020
> > +#define CONFIG_SYS_FSL_ESDHC_USE_PIO /* P2020 eSDHC DMA is not
> > functional*/
> > +#endif
> > +#endif
> > +/*
> > + * Miscellaneous configurable options */
> > +#define CONFIG_SYS_LONGHELP /*
> undef to save memory */
> > +#define CONFIG_CMDLINE_EDITING /* Command-line
> editing */
> > +#define CONFIG_SYS_LOAD_ADDR 0x2000000 /*
> default load address */
> > +#define CONFIG_SYS_PROMPT "=> " /* Monitor
> Command Prompt */
> > +#if defined(CONFIG_CMD_KGDB)
> > +#define CONFIG_SYS_CBSIZE 1024 /* Console I/O
> Buffer Size */
> > +#else
> > +#define CONFIG_SYS_CBSIZE 256 /* Console I/O
> Buffer Size */
> > +#endif
> > +#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE
> > +sizeof(CONFIG_SYS_PROMPT)+16) /* Print Buffer Size */
> > +#define CONFIG_SYS_MAXARGS 16 /* max number
> of command args */
> > +#define CONFIG_SYS_BARGSIZE CONFIG_SYS_CBSIZE
> /* Boot Argument
> > Buffer Size */
> > +#define CONFIG_SYS_HZ 1000 /*
> decrementer freq: 1ms ticks */
> > +
> > +/*
> > + * For booting Linux, the board info and command line data
> > + * have to be in the first 8 MB of memory, since this is
>
> 8 MB -> 16 MB
>
> >
> > + * the maximum mapped by the Linux kernel during initialization.
> > + */
> > +#define CONFIG_SYS_BOOTMAPSZ (8 << 20) /*
> Initial Memory map for
> > Linux*/
>
> Make this (16 << 20)
> >
> > +
> > +/*
> > + * Internal Definitions
> > + *
> > + * Boot Flags
> > + */
> > +#define BOOTFLAG_COLD 0x01 /* Normal
> Power-On: Boot from FLASH */
> > +#define BOOTFLAG_WARM 0x02 /* Software reboot */
> > +
> > +#if defined(CONFIG_CMD_KGDB)
> > +#define CONFIG_KGDB_BAUDRATE 230400 /* speed to run
> kgdb serial
> > port */
> > +#define CONFIG_KGDB_SER_INDEX 2 /* which serial
> port to use */
> > +#endif
> > +
> > +/*
> > + * Environment Configuration
> > + */
> > +
> > +#if defined(CONFIG_TSEC_ENET)
> > +#define CONFIG_HAS_ETH0
> > +#define CONFIG_HAS_ETH1
> > +#define CONFIG_HAS_ETH2
> > +#endif
> > +
> > +#define CONFIG_HOSTNAME unknown
> > +#define CONFIG_ROOTPATH /opt/nfsroot
> > +#define CONFIG_BOOTFILE uImage
> > +#define CONFIG_UBOOTPATH u-boot.bin /* U-Boot image
> on TFTP server */
> > +
> > +/* default location for tftp and bootm */
> > +#define CONFIG_LOADADDR 1000000
> > +
> > +#define CONFIG_BOOTDELAY 10 /* -1 disables auto-boot */
> > +#undef CONFIG_BOOTARGS /* the boot command
> will set bootargs */
> > +
> > +#define CONFIG_BAUDRATE 115200
> > +
> > +#define CONFIG_EXTRA_ENV_SETTINGS
> \
> > + "netdev=eth0\0" \
> > + "uboot=" MK_STR(CONFIG_UBOOTPATH) "\0"
> \
> > + "loadaddr=1000000\0" \
> > + "bootfile=uImage\0" \
> > + "tftpflash=tftpboot $loadaddr $uboot; " \
> > + "protect off " MK_STR(TEXT_BASE) " +$filesize; " \
> > + "erase " MK_STR(TEXT_BASE) " +$filesize; " \
> > + "cp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize; " \
> > + "protect on " MK_STR(TEXT_BASE) " +$filesize; " \
> > + "cmp.b $loadaddr " MK_STR(TEXT_BASE) " $filesize\0" \
> > + "consoledev=ttyS0\0" \
> > + "ramdiskaddr=2000000\0" \
> > + "ramdiskfile=rootfs.ext2.gz.uboot\0" \
> > + "fdtaddr=c00000\0" \
> > + "fdtfile=p2020rdb.dtb\0" \
> > + "bdev=sda1\0" \
> > + "jffs2nor=mtdblock3\0" \
> > + "norbootaddr=ef080000\0" \
> > + "norfdtaddr=ef040000\0" \
> > + "jffs2nand=mtdblock9\0" \
> > + "nandbootaddr=100000\0" \
> > + "nandfdtaddr=80000\0" \
> > + "usb_phy_type=ulpi\0" \
> > + "usbfatboot=setenv bootargs root=/dev/ram rw " \
> > + "console=$consoledev,$baudrate $othbootargs " \
> > + "ramdisk_size=120000;" \
> > + "usb start;" \
> > + "fatload usb 0:2 $loadaddr $bootfile;" \
> > + "fatload usb 0:2 $fdtaddr $fdtfile;" \
> > + "fatload usb 0:2 $ramdiskaddr $ramdiskfile;" \
> > + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
> > + "usbext2boot=setenv bootargs root=/dev/ram rw " \
> > + "console=$consoledev,$baudrate $othbootargs " \
> > + "ramdisk_size=120000;" \
> > + "usb start;" \
> > + "ext2load usb 0:4 $loadaddr $bootfile;" \
> > + "ext2load usb 0:4 $fdtaddr $fdtfile;" \
> > + "ext2load usb 0:4 $ramdiskaddr $ramdiskfile;" \
> > + "bootm $loadaddr $ramdiskaddr $fdtaddr\0" \
> > + "norboot=setenv bootargs root=/dev/$jffs2nor rw " \
> > + "console=$consoledev,$baudrate rootfstype=jffs2
> $othbootargs;" \
> > + "bootm $norbootaddr - $norfdtaddr\0" \
> > + "nandboot=setenv bootargs root=/dev/$jffs2nand rw rootfstype=jffs2
> > " \
> > + "console=$consoledev,$baudrate $othbootargs;" \
> > + "nand read 2000000 100000 400000;" \
> > + "nand read 3000000 80000 80000;" \
> > + "bootm 2000000 - 3000000;\0"
> > +
> > +
> > +#define CONFIG_NFSBOOTCOMMAND \
> > + "setenv bootargs root=/dev/nfs rw " \
> > + "nfsroot=$serverip:$rootpath " \
> > +
> "ip=$ipaddr:$serverip:$gatewayip:$netmask:$hostname:$netdev:off " \
> > + "console=$consoledev,$baudrate $othbootargs;" \
> > + "tftp $loadaddr $bootfile;" \
> > + "tftp $fdtaddr $fdtfile;" \
> > + "bootm $loadaddr - $fdtaddr"
> > +
> > +#define CONFIG_HDBOOT \
> > + "setenv bootargs root=/dev/$bdev rw rootdelay=30 " \
> > + "console=$consoledev,$baudrate $othbootargs;" \
> > + "usb start;" \
> > + "ext2load usb 0:1 $loadaddr /boot/$bootfile;" \
> > + "ext2load usb 0:1 $fdtaddr /boot/$fdtfile;" \
> > + "bootm $loadaddr - $fdtaddr"
> > +
> > +#define CONFIG_RAMBOOTCOMMAND \
> > + "setenv bootargs root=/dev/ram rw " \
> > + "console=$consoledev,$baudrate $othbootargs " \
> > + "ramdisk_size=120000;" \
> > + "tftp $ramdiskaddr $ramdiskfile;" \
> > + "tftp $loadaddr $bootfile;" \
> > + "tftp $fdtaddr $fdtfile;" \
> > + "bootm $loadaddr $ramdiskaddr $fdtaddr"
> > +
> > +#define CONFIG_BOOTCOMMAND CONFIG_HDBOOT
> > +
> > +#endif /* __CONFIG_H */
> > --
> > 1.5.6.3
> >
> > _______________________________________________
> > U-Boot mailing list
> > U-Boot at lists.denx.de
> > http://lists.denx.de/mailman/listinfo/u-boot
>
>
More information about the U-Boot
mailing list