[U-Boot] [PATCH 3/4] ZOOM2 Add power reset button

[Tom Rix]

The power reset button is on the top right side of the main board.
Press and hold for about to 8 seconds to completely reset the board.

Some of the beta boards have a hardware problem that prevents
using this feature.  If is difficult to further characterize the
boards that fail.  So disable resetting for all beta boards.

Signed-off-by: Tom Rix <Tom.Rix at windriver.com>
---
 board/omap3/zoom2/zoom2.c     |   13 +++++++++++++
 drivers/i2c/twl4030_i2c.c     |   22 ++++++++++++++++++++++
 include/configs/omap3_zoom2.h |    1 +
 include/twl4030.h             |   10 ++++++++++
 4 files changed, 46 insertions(+), 0 deletions(-)

diff --git a/board/omap3/zoom2/zoom2.c b/board/omap3/zoom2/zoom2.c
index 08fdafb..d5da920 100644
--- a/board/omap3/zoom2/zoom2.c
+++ b/board/omap3/zoom2/zoom2.c
@@ -32,6 +32,7 @@
 #ifdef CONFIG_STATUS_LED
 #include <status_led.h>
 #endif
+#include <twl4030.h>
 #include <asm/io.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/mem.h>
@@ -141,6 +142,18 @@ int board_init (void)
 	/* boot param addr */
 	gd->bd->bi_boot_params = (OMAP34XX_SDRC_CS0 + 0x100);
 
+	/*
+	 * Board Reset
+	 * The board is reset by holding the the large button
+	 * on the top right side of the main board for
+	 * eight seconds.
+	 *
+	 * There are reported problems of some beta boards
+	 * continously resetting.  For those boards, disable resetting.
+	 */
+	if (ZOOM2_REVISION_PRODUCTION <= zoom2_get_revision())
+		twl4030_power_reset_init();
+
 #if defined(CONFIG_STATUS_LED) && defined(STATUS_LED_BOOT)
 	status_led_set (STATUS_LED_BOOT, STATUS_LED_ON);
 #endif
diff --git a/drivers/i2c/twl4030_i2c.c b/drivers/i2c/twl4030_i2c.c
index 774f813..549f974 100644
--- a/drivers/i2c/twl4030_i2c.c
+++ b/drivers/i2c/twl4030_i2c.c
@@ -35,3 +35,25 @@ static inline int twl4030_i2c_read_u8(u8 chip_no, u8 *val, u8 reg)
 	return i2c_read(chip_no, reg, 1, val, 1);
 }
 
+/*
+ * Power Reset
+ */
+void twl4030_power_reset_init(void)
+{
+#ifdef CONFIG_OMAP3_ZOOM2
+	u8 val = 0;
+	if (twl4030_i2c_read_u8(TWL4030_CHIP_PM_MASTER, &val,
+				TWL4030_PM_MASTER_P1_SW_EVENTS)) {
+		printf("Error:TWL4030: failed to read the power register\n");
+		printf("Could not initialize hardware reset\n");
+	} else {
+		val |= TWL4030_PM_MASTER_SW_EVENTS_STOPON_PWRON;
+		if (twl4030_i2c_write_u8(TWL4030_CHIP_PM_MASTER, val,
+					 TWL4030_PM_MASTER_P1_SW_EVENTS)) {
+			printf("Error:TWL4030: failed to write the power register\n");
+			printf("Could not initialize hardware reset\n");
+		}
+	}
+#endif
+}
+
diff --git a/include/configs/omap3_zoom2.h b/include/configs/omap3_zoom2.h
index c2ad5bf..e69c5f1 100644
--- a/include/configs/omap3_zoom2.h
+++ b/include/configs/omap3_zoom2.h
@@ -145,6 +145,7 @@
 #define CONFIG_SYS_I2C_BUS		0
 #define CONFIG_SYS_I2C_BUS_SELECT	1
 #define CONFIG_DRIVER_OMAP34XX_I2C	1
+#define CONFIG_DRIVER_TWL4030_I2C	1
 
 /*
  * Board NAND Info.
diff --git a/include/twl4030.h b/include/twl4030.h
index d17fea5..bb07036 100644
--- a/include/twl4030.h
+++ b/include/twl4030.h
@@ -218,4 +218,14 @@
 #define TWL4030_USB_PHY_CLK_CTRL_STS			(0xFF)
 #define TWL4030_USB_PHY_DPLL_CLK			(1 << 0)
 
+#ifdef CONFIG_DRIVER_TWL4030_I2C
+
+/* Power Reset, use to initialize system wide resetting */
+void twl4030_power_reset_init(void);
+
+#else
+/* stubs */
+#define twl4030_power_reset_init()
+
+#endif /* CONFIG_DRIVER_TWL4030_I2C */
 #endif /* TWL4030_H */
-- 
1.6.0.5