[U-Boot] [PATCH v4 3/3][repost] Marvell Sheevaplug Board support
Prafulla Wadaskar
prafulla at marvell.com
Sun Jun 14 19:04:25 CEST 2009
Reference:
http://plugcomputer.org/
http://openplug.org/plugwiki/index.php/Das_U-boot_plug_support
This patch is tested for-
1. Boot from DRAM/NAND flash
2. File transfer using tftp
3. NAND flash read/write/erase
4. Linux kernel and RFS Boot from NAND
Signed-off-by: Prafulla Wadaskar <prafulla at marvell.com>
---
Change log:
v2: updated as per feedback for v1
v3: updated as per feedback for v2
v4: removed PHY driver dependency, coded in sheevaplug.c
MAINTAINERS | 4 +
MAKEALL | 1 +
Makefile | 4 +-
board/Marvell/sheevaplug/Makefile | 51 +++++++++
board/Marvell/sheevaplug/config.mk | 25 +++++
board/Marvell/sheevaplug/sheevaplug.c | 155 ++++++++++++++++++++++++++
board/Marvell/sheevaplug/sheevaplug.h | 41 +++++++
include/configs/sheevaplug.h | 191 +++++++++++++++++++++++++++++++++
8 files changed, 471 insertions(+), 1 deletions(-)
create mode 100644 board/Marvell/sheevaplug/Makefile
create mode 100644 board/Marvell/sheevaplug/config.mk
create mode 100644 board/Marvell/sheevaplug/sheevaplug.c
create mode 100644 board/Marvell/sheevaplug/sheevaplug.h
create mode 100644 include/configs/sheevaplug.h
diff --git a/MAINTAINERS b/MAINTAINERS
index bf076b9..2474481 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -655,6 +655,10 @@ Hugo Villeneuve <hugo.villeneuve at lyrtech.com>
SFFSDR ARM926EJS
+Prafulla Wadaskar <prafulla at marvell.com>
+
+ sheevaplug ARM926EJS (Kirkwood SoC)
+
Richard Woodruff <r-woodruff2 at ti.com>
omap2420h4 ARM1136EJS
diff --git a/MAKEALL b/MAKEALL
index c98d03a..4a7ccee 100755
--- a/MAKEALL
+++ b/MAKEALL
@@ -516,6 +516,7 @@ LIST_ARM9=" \
omap730p2 \
sbc2410x \
scb9328 \
+ sheevaplug \
smdk2400 \
smdk2410 \
trab \
diff --git a/Makefile b/Makefile
index 81a5cd0..527e383 100644
--- a/Makefile
+++ b/Makefile
@@ -2879,6 +2879,9 @@ sbc2410x_config: unconfig
scb9328_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t scb9328 NULL imx
+sheevaplug_config: unconfig
+ @$(MKCONFIG) $(@:_config=) arm arm926ejs $(@:_config=) Marvell kirkwood
+
smdk2400_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm920t smdk2400 samsung s3c24x0
@@ -3107,7 +3110,6 @@ omap2420h4_config : unconfig
qong_config : unconfig
@$(MKCONFIG) $(@:_config=) arm arm1136 qong davedenx mx31
-
#########################################################################
## ARM1176 Systems
#########################################################################
diff --git a/board/Marvell/sheevaplug/Makefile b/board/Marvell/sheevaplug/Makefile
new file mode 100644
index 0000000..e378b5b
--- /dev/null
+++ b/board/Marvell/sheevaplug/Makefile
@@ -0,0 +1,51 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+include $(TOPDIR)/config.mk
+
+LIB = $(obj)lib$(BOARD).a
+
+COBJS := sheevaplug.o
+
+SRCS := $(SOBJS:.o=.S) $(COBJS:.o=.c)
+OBJS := $(addprefix $(obj),$(COBJS))
+SOBJS := $(addprefix $(obj),$(SOBJS))
+
+$(LIB): $(obj).depend $(OBJS) $(SOBJS)
+ $(AR) $(ARFLAGS) $@ $(OBJS) $(SOBJS)
+
+clean:
+ rm -f $(SOBJS) $(OBJS)
+
+distclean: clean
+ rm -f $(LIB) core *.bak .depend
+
+#########################################################################
+
+# defines $(obj).depend target
+include $(SRCTREE)/rules.mk
+
+sinclude $(obj).depend
+
+#########################################################################
diff --git a/board/Marvell/sheevaplug/config.mk b/board/Marvell/sheevaplug/config.mk
new file mode 100644
index 0000000..a4ea769
--- /dev/null
+++ b/board/Marvell/sheevaplug/config.mk
@@ -0,0 +1,25 @@
+#
+# (C) Copyright 2009
+# Marvell Semiconductor <www.marvell.com>
+# Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+#
+# See file CREDITS for list of people who contributed to this
+# project.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation; either version 2 of
+# the License, or (at your option) any later version.
+#
+# This program is distributed in the hope that it will be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write to the Free Software
+# Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+# MA 02110-1301 USA
+#
+
+TEXT_BASE = 0x00600000
diff --git a/board/Marvell/sheevaplug/sheevaplug.c b/board/Marvell/sheevaplug/sheevaplug.c
new file mode 100644
index 0000000..547126a
--- /dev/null
+++ b/board/Marvell/sheevaplug/sheevaplug.c
@@ -0,0 +1,155 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#include <common.h>
+#include <miiphy.h>
+#include <asm/arch/kirkwood.h>
+#include <asm/arch/mpp.h>
+#include "sheevaplug.h"
+
+DECLARE_GLOBAL_DATA_PTR;
+
+int board_init(void)
+{
+ /*
+ * default gpio configuration
+ * There are maximum 64 gpios controlled through 2 sets of registers
+ * the below configuration configures mainly initial LED status
+ */
+ kw_config_gpio(SHEEVAPLUG_OE_VAL_LOW,
+ SHEEVAPLUG_OE_VAL_HIGH,
+ SHEEVAPLUG_OE_LOW, SHEEVAPLUG_OE_HIGH);
+
+ /* Multi-Purpose Pins Functionality configuration */
+ u32 kwmpp_config[] = {
+ MPP0_NF_IO2,
+ MPP1_NF_IO3,
+ MPP2_NF_IO4,
+ MPP3_NF_IO5,
+ MPP4_NF_IO6,
+ MPP5_NF_IO7,
+ MPP6_SYSRST_OUTn,
+ MPP7_GPO,
+ MPP8_UART0_RTS,
+ MPP9_UART0_CTS,
+ MPP10_UART0_TXD,
+ MPP11_UART0_RXD,
+ MPP12_SD_CLK,
+ MPP13_SD_CMD,
+ MPP14_SD_D0,
+ MPP15_SD_D1,
+ MPP16_SD_D2,
+ MPP17_SD_D3,
+ MPP18_NF_IO0,
+ MPP19_NF_IO1,
+ MPP20_GPIO,
+ MPP21_GPIO,
+ MPP22_GPIO,
+ MPP23_GPIO,
+ MPP24_GPIO,
+ MPP25_GPIO,
+ MPP26_GPIO,
+ MPP27_GPIO,
+ MPP28_GPIO,
+ MPP29_TSMP9,
+ MPP30_GPIO,
+ MPP31_GPIO,
+ MPP32_GPIO,
+ MPP33_GPIO,
+ MPP34_GPIO,
+ MPP35_GPIO,
+ MPP36_GPIO,
+ MPP37_GPIO,
+ MPP38_GPIO,
+ MPP39_GPIO,
+ MPP40_GPIO,
+ MPP41_GPIO,
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ MPP49_GPIO,
+ 0
+ };
+ kirkwood_mpp_conf(kwmpp_config);
+
+ /*
+ * arch number of board
+ */
+ gd->bd->bi_arch_number = MACH_TYPE_SHEEVAPLUG;
+
+ /* adress of boot parameters */
+ gd->bd->bi_boot_params = kw_sdram_bar(0) + 0x100;
+
+ return 0;
+}
+
+int dram_init(void)
+{
+ int i;
+
+ for (i = 0; i < CONFIG_NR_DRAM_BANKS; i++) {
+ gd->bd->bi_dram[i].start = kw_sdram_bar(i);
+ gd->bd->bi_dram[i].size = kw_sdram_bs(i);
+ }
+ return 0;
+}
+
+#ifdef CONFIG_RESET_PHY_R
+/* Configure and enable MV88E1116 PHY */
+void reset_phy(void)
+{
+ u16 reg;
+ u16 devadr;
+ char *name = "egiga0";
+
+ if (miiphy_set_current_dev(name))
+ return;
+
+ /* command to read PHY dev address */
+ if (miiphy_read(name, 0xEE, 0xEE, (u16 *) &devadr)) {
+ printf("Err..%s could not read PHY dev address\n",
+ __FUNCTION__);
+ return;
+ }
+
+ /*
+ * Enable RGMII delay on Tx and Rx for CPU port
+ * Ref: sec 4.7.2 of chip datasheet
+ */
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 2);
+ miiphy_read(name, devadr, MV88E1116_MAC_CTRL_REG, ®);
+ reg |= (MV88E1116_RGMII_RXTM_CTRL | MV88E1116_RGMII_TXTM_CTRL);
+ miiphy_write(name, devadr, MV88E1116_MAC_CTRL_REG, reg);
+ miiphy_write(name, devadr, MV88E1116_PGADR_REG, 0);
+
+ /* reset the phy */
+ miiphy_reset(name, devadr);
+
+ printf("88E1116 Initialized on %s\n", name);
+}
+#endif /* CONFIG_RESET_PHY_R */
diff --git a/board/Marvell/sheevaplug/sheevaplug.h b/board/Marvell/sheevaplug/sheevaplug.h
new file mode 100644
index 0000000..3ed5b7f
--- /dev/null
+++ b/board/Marvell/sheevaplug/sheevaplug.h
@@ -0,0 +1,41 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef __SHEEVAPLUG_H
+#define __SHEEVAPLUG_H
+
+#define SHEEVAPLUG_OE_LOW (~(0))
+#define SHEEVAPLUG_OE_HIGH (~(0))
+#define SHEEVAPLUG_OE_VAL_LOW (1 << 29) /* USB_PWEN low */
+#define SHEEVAPLUG_OE_VAL_HIGH (1 << 17) /* LED pin high */
+
+/* PHY related */
+#define MV88E1116_LED_FCTRL_REG 10
+#define MV88E1116_CPRSP_CR3_REG 21
+#define MV88E1116_MAC_CTRL_REG 21
+#define MV88E1116_PGADR_REG 22
+#define MV88E1116_RGMII_TXTM_CTRL (1 << 4)
+#define MV88E1116_RGMII_RXTM_CTRL (1 << 5)
+
+#endif /* __SHEEVAPLUG_H */
diff --git a/include/configs/sheevaplug.h b/include/configs/sheevaplug.h
new file mode 100644
index 0000000..0c7545a
--- /dev/null
+++ b/include/configs/sheevaplug.h
@@ -0,0 +1,191 @@
+/*
+ * (C) Copyright 2009
+ * Marvell Semiconductor <www.marvell.com>
+ * Written-by: Prafulla Wadaskar <prafulla at marvell.com>
+ *
+ * See file CREDITS for list of people who contributed to this
+ * project.
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston,
+ * MA 02110-1301 USA
+ */
+
+#ifndef _CONFIG_SHEEVAPLUG_H
+#define _CONFIG_SHEEVAPLUG_H
+
+/*
+ * Version number information
+ */
+#define CONFIG_IDENT_STRING "\nMarvell-Sheevaplug"
+
+/*
+ * High Level Configuration Options (easy to change)
+ */
+#define CONFIG_MARVELL 1
+#define CONFIG_ARM926EJS 1 /* Basic Architecture */
+#define CONFIG_FEROCEON_88FR131 1 /* CPU Core subversion */
+#define CONFIG_KIRKWOOD 1 /* SOC Family Name */
+#define CONFIG_KW88F6281 1 /* SOC Name */
+#define CONFIG_MACH_SHEEVAPLUG /* Machine type */
+
+#define CONFIG_MD5 /* get_random_hex on krikwood needs MD5 support */
+#define CONFIG_SKIP_LOWLEVEL_INIT /* disable board lowlevel_init */
+#define CONFIG_KIRKWOOD_EGIGA_INIT /* Enable GbePort0/1 for kernel */
+#define CONFIG_KIRKWOOD_RGMII_PAD_1V8 /* Set RGMII Pad voltage to 1.8V */
+
+/*
+ * CLKs configurations
+ */
+#define CONFIG_SYS_HZ 1000
+
+/*
+ * NS16550 Configuration
+ */
+#define CONFIG_SYS_NS16550
+#define CONFIG_SYS_NS16550_SERIAL
+#define CONFIG_SYS_NS16550_REG_SIZE (-4)
+#define CONFIG_SYS_NS16550_CLK CONFIG_SYS_TCLK
+#define CONFIG_SYS_NS16550_COM1 KW_UART0_BASE
+
+/*
+ * Serial Port configuration
+ * The following definitions let you select what serial you want to use
+ * for your console driver.
+ */
+
+#define CONFIG_CONS_INDEX 1 /*Console on UART0 */
+#define CONFIG_BAUDRATE 115200
+#define CONFIG_SYS_BAUDRATE_TABLE { 9600, 19200, 38400, 57600, \
+ 115200,230400, 460800, 921600 }
+/* auto boot */
+#define CONFIG_BOOTDELAY 3 /* default enable autoboot */
+
+/*
+ * For booting Linux, the board info and command line data
+ * have to be in the first 8 MB of memory, since this is
+ * the maximum mapped by the Linux kernel during initialization.
+ */
+#define CONFIG_CMDLINE_TAG 1 /* enable passing of ATAGs */
+#define CONFIG_INITRD_TAG 1 /* enable INITRD tag */
+#define CONFIG_SETUP_MEMORY_TAGS 1 /* enable memory tag */
+
+#define CONFIG_SYS_PROMPT "Marvell>> " /* Command Prompt */
+#define CONFIG_SYS_CBSIZE 1024 /* Console I/O Buff Size */
+#define CONFIG_SYS_PBSIZE (CONFIG_SYS_CBSIZE \
+ +sizeof(CONFIG_SYS_PROMPT) + 16) /* Print Buff */
+/*
+ * Commands configuration
+ */
+#define CONFIG_CMD_AUTOSCRIPT
+#define CONFIG_CMD_BOOTD
+#define CONFIG_CMD_DHCP
+#define CONFIG_CMD_ENV
+#define CONFIG_CMD_LOADB
+#define CONFIG_CMD_MEMORY
+#define CONFIG_CMD_NAND
+#define CONFIG_CMD_NET
+#define CONFIG_CMD_PING
+#define CONFIG_CMD_RUN
+#define CONFIG_CMD_SAVEENV
+
+/*
+ * Flash configuration
+ */
+#ifndef CONFIG_CMD_FLASH
+#define CONFIG_SYS_NO_FLASH 1 /* Declare no flash (NOR/SPI) */
+#endif
+
+/*
+ * NAND configuration
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_NAND_KIRKWOOD
+#define CONFIG_SYS_MAX_NAND_DEVICE 1
+#define NAND_MAX_CHIPS 1
+#define CONFIG_SYS_NAND_BASE 0xD8000000 /* KW_DEFADR_NANDF */
+#define NAND_ALLOW_ERASE_ALL 1
+#endif
+
+/*
+ * Environment variables configurations
+ */
+#ifdef CONFIG_CMD_NAND
+#define CONFIG_ENV_IS_IN_NAND 1
+#define CONFIG_ENV_SECT_SIZE 0x20000 /* 128K */
+#else
+#define CONFIG_ENV_IS_NOWHERE 1 /* if env in SDRAM */
+#endif
+/*
+ * max 4k env size is enough, but in case of nand
+ * it has to be rounded to sector size
+ */
+#define CONFIG_ENV_SIZE 0x20000 /* 128k */
+#define CONFIG_ENV_ADDR 0x40000
+#define CONFIG_ENV_OFFSET 0x40000 /* env starts here */
+
+/*
+ * Default environment variables
+ */
+#define CONFIG_BOOTCOMMAND "${x_bootcmd_kernel}; " \
+ "setenv bootargs ${x_bootargs} ${x_bootargs_root}; " \
+ "bootm 0x6400000;"
+
+#define CONFIG_MTDPARTS "orion_nand:512k(uboot)," \
+ "3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootfs) rw\0"
+
+#define CONFIG_EXTRA_ENV_SETTINGS "x_bootargs=console" \
+ "=ttyS0,115200 mtdparts="CONFIG_MTDPARTS \
+ "x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000\0" \
+ "x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2\0"
+
+/*
+ * Size of malloc() pool
+ */
+#define CONFIG_SYS_MALLOC_LEN (1024 * 128) /* 128kB for malloc() */
+/* size in bytes reserved for initial data */
+#define CONFIG_SYS_GBL_DATA_SIZE 128
+
+/*
+ * Other required minimal configurations
+ */
+#define CONFIG_CONSOLE_INFO_QUIET /* some code reduction */
+#define CONFIG_ARCH_CPU_INIT /* call arch_cpu_init() */
+#define CONFIG_ARCH_MISC_INIT /* call arch_misc_init() */
+#define CONFIG_DISPLAY_CPUINFO /* Display cpu info */
+#define CONFIG_NR_DRAM_BANKS 4
+#define CONFIG_STACKSIZE 0x00100000 /* regular stack- 1M */
+#define CONFIG_SYS_LOAD_ADDR 0x00800000 /* default load adr- 8M */
+#define CONFIG_SYS_MEMTEST_START 0x00400000 /* 4M */
+#define CONFIG_SYS_MEMTEST_END 0x007fffff /*(_8M -1) */
+#define CONFIG_SYS_RESET_ADDRESS 0xffff0000 /* Rst Vector Adr */
+#define CONFIG_SYS_MAXARGS 16 /* max number of command args */
+
+/*
+ * Ethernet Driver configuration
+ */
+#ifdef CONFIG_CMD_NET
+#define CONFIG_NETCONSOLE /* include NetConsole support */
+#define CONFIG_NET_MULTI /* specify more that one ports available */
+#define CONFIG_MII /* expose smi ove miiphy interface */
+#define CONFIG_KIRKWOOD_EGIGA /* Enable kirkwood Gbe Controller Driver */
+#define CONFIG_SYS_FAULT_ECHO_LINK_DOWN /* detect link using phy */
+#define CONFIG_KIRKWOOD_EGIGA_PORTS {1,0} /* enable port 0 only */
+#define CONFIG_PHY_BASE_ADR 0
+#define CONFIG_ENV_OVERWRITE /* ethaddr can be reprogrammed */
+#define CONFIG_RESET_PHY_R /* use reset_phy() to init mv8831116 PHY */
+#endif /* CONFIG_CMD_NET */
+
+
+#endif /* _CONFIG_SHEEVAPLUG_H */
--
1.5.3.4
More information about the U-Boot
mailing list