[U-Boot] Kirkwood (Sheevaplug) ping crashes(?) U-Boot

[Dieter Kiermaier]

Am Montag 22 Juni 2009 14:53:44 schrieb André Schwarz:
> On Mon, 2009-06-22 at 14:41 +0200, Dieter Kiermaier wrote:
> > André,
> >
> > > Dieter,
> > >
> > > On Mon, 2009-06-22 at 14:04 +0200, Dieter Kiermaier wrote:
> > > > Hi all,
> > > >
> > > > I've tried the first time booting a self compiled u-boot from
> > > > git.marvell.com U-Boot can be downloaded and started with openocd
> > > > quite well.
> > > > Boot messages (version is dirty due to a comment in board file):
> > > >
> > > > U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
> > > > Marvell-Sheevaplug
> > > >
> > > > SoC:   Kirkwood 88F6281_A0
> > > > DRAM:  512 MB
> > > > NAND:  512 MiB
> > > > *** Warning - bad CRC or NAND, using default environment
> > >
> > > most propably you'll need to save the environment.
> >
> > Also saving environment doesn't help.
> > The bad CRC message disappered as expected but that's all what happened.
> >
> > > > In:    serial
> > > > Out:   serial
> > > > Err:   serial
> > > > Net:   egiga0
> > > > 88E1116 Initialized on egiga0
> > > > Hit any key to stop autoboot:  0
> > > > Marvell>>
> > >
> > > type "save" here and "reset".
> > >
> > > > Environment is broken only with marvell git u-boot. Preflashed u-boot
> > > > find environment is ok.
> > > > Does sheevaplug u-boot from marvell git use other environment
> > > > settings than preflashed u-boot?
> > > >
> > > > Marvell>> printenv
> > > > bootcmd=${x_bootcmd_kernel}; setenv bootargs ${x_bootargs}
> > > > ${x_bootargs_root}; bootm 0x6400000;
> > > > bootdelay=3
> > > > baudrate=115200
> > > > x_bootargs=console=ttyS0,115200
> > > > mtdparts=orion_nand:512k(uboot),3m at 1m(kernel),1m at 4m(psm),13m at 5m(rootf
> > > >s) rw x_bootcmd_kernel=nand read 0x100000 0x6400000 0x300000
> > > > x_bootargs_root=root=/dev/mtdblock3 rw rootfstype=jffs2
> > > > stdin=serial
> > > > stdout=serial
> > > > stderr=serial
> > > > ethaddr=00:50:43:e0:b9:d8
> > > > ethact=egiga0
> > > > ipaddr=192.168.2.75
> > > >
> > > > (ipaddr is set after bootup with setenv ipaddr 192.168.2.75)
>
> Did you try "bootp" or "dhcp" to set up the I/F ?
>
Yes, but everytimes the same:
Marvell>> dhcp
BOOTP broadcast 1

... machine hangs and only a reset helps...


U-Boot 2009.06-rc2-02207-g14c575a-dirty (Jun 22 2009 - 13:40:45)
Marvell-Sheevaplug

SoC:   Kirkwood 88F6281_A0
DRAM:  512 MB
NAND:  512 MiB
*** Warning - bad CRC or NAND, using default environment

In:    serial
Out:   serial
Err:   serial
Net:   egiga0
88E1116 Initialized on egiga0
Hit any key to stop autoboot:  0
Marvell>> bootp
BOOTP broadcast 1

...the same here again...

It seems that the network would be activated (1 blink on the activity LED) but 
nothing more happens.


> > > > If I now try to ping another machine in the same network:
> > > > Marvell>> ping 192.168.2.251
> > > > Using egiga0 device
> > >
> > > maybe your MAC is missing ? environment ?
> >
> > MAC is available in default (compiled in environment) as shown in env 
above:
> > > > ethaddr=00:50:43:e0:b9:d8
> >
> > Also writing a new MAC to environment / savenenv / reset made no
> > difference :(
> >
> > > > This is all what happens - no response from board, CTRL-C doesn't
> > > > work. Only a hard reset will get the board up again.
> > > >
> > > > Do I have to change something in the default board configuration to
> > > > succesfullly use networking on the sheevaplug?
> > > >
> > > > u-boot is build with following commands:
> > > >
> > > > make ARCH=arm sheevaplug_config
> > > > make
> > > >
> > > > I get no errors during build.
> > > >
> > > > My gcc version is:
> > > > arm-none-linux-gnueabi-gcc (GCC) 4.2.0 20070413 (prerelease)
> > > >
> > > > Any help would be appreciated,
> > > > Dieter
> > >
> > > Regards,
> > >
> > > André
> >
> > Dieter
> >
> > > > _______________________________________________
> > > > U-Boot mailing list
> > > > U-Boot at lists.denx.de
> > > > http://lists.denx.de/mailman/listinfo/u-boot
> > >
> > > MATRIX VISION GmbH, Talstrae 16, DE-71570 Oppenweiler
> > > Registergericht: Amtsgericht Stuttgart, HRB 271090
> > > Geschftsfhrer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> > > Hans-Joachim Reich
>
> MATRIX VISION GmbH, Talstraße 16, DE-71570 Oppenweiler
> Registergericht: Amtsgericht Stuttgart, HRB 271090
> Geschäftsführer: Gerhard Thullner, Werner Armingeon, Uwe Furtner,
> Hans-Joachim Reich