[U-Boot] [PATCH 2/2] usb: add Kirkwood ehci driver support

[Prafulla Wadaskar]

Features supported:
1. usb-phy init support (tested on sheevaplug)
   This support is required to bring up USB interface
   at kernel level on Kirkwood platforms

Signed-off-by: Prafulla Wadaskar <prafulla at marvell.com>
---
 drivers/usb/host/Makefile        |    1 +
 drivers/usb/host/ehci-kirkwood.c |  102 ++++++++++++++++++++++++++++++++++++++
 2 files changed, 103 insertions(+), 0 deletions(-)
 create mode 100644 drivers/usb/host/ehci-kirkwood.c

diff --git a/drivers/usb/host/Makefile b/drivers/usb/host/Makefile
index ec1d689..4fe7cb3 100644
--- a/drivers/usb/host/Makefile
+++ b/drivers/usb/host/Makefile
@@ -37,6 +37,7 @@ COBJS-$(CONFIG_USB_SL811HS) += sl811-hcd.o
 COBJS-$(CONFIG_USB_EHCI) += ehci-hcd.o
 COBJS-$(CONFIG_USB_EHCI_FSL) += ehci-fsl.o
 COBJS-$(CONFIG_USB_EHCI_IXP4XX) += ehci-ixp.o
+COBJS-$(CONFIG_USB_EHCI_KIRKWOOD)	+= ehci-kirkwood.o
 COBJS-$(CONFIG_USB_EHCI_PCI) += ehci-pci.o
 COBJS-$(CONFIG_USB_EHCI_VCT) += ehci-vct.o
 
diff --git a/drivers/usb/host/ehci-kirkwood.c b/drivers/usb/host/ehci-kirkwood.c
new file mode 100644
index 0000000..8e0aa83
--- /dev/null
+++ b/drivers/usb/host/ehci-kirkwood.c
@@ -0,0 +1,102 @@
+/*
+ * original file from linux: drivers/usb/host/ehci-orion.c
+ *
+ * Tzachi Perelstein <tzachi at marvell.com>
+ *
+ * Updated-by: Prafulla Wadaskar <prafulla at marvell.com>
+ * Purpose: to reuse usb_phy_v1_setup function
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <common.h>
+#include <asm/arch/kirkwood.h>
+
+#define rdl(off)	readl(KW_USB20_BASE + (off))
+#define wrl(off, val)	writel((val), KW_USB20_BASE + (off))
+
+#define USB_CMD			0x140
+#define USB_MODE		0x1a8
+#define USB_CAUSE		0x310
+#define USB_MASK		0x314
+#define USB_WINDOW_CTRL(i)	(0x320 + ((i) << 4))
+#define USB_WINDOW_BASE(i)	(0x324 + ((i) << 4))
+#define USB_IPG			0x360
+#define USB_PHY_PWR_CTRL	0x400
+#define USB_PHY_TX_CTRL		0x420
+#define USB_PHY_RX_CTRL		0x430
+#define USB_PHY_IVREF_CTRL	0x440
+#define USB_PHY_TST_GRP_CTRL	0x450
+
+/*
+ * Implement Orion USB controller specification guidelines
+ */
+void orion_usb_phy_v1_setup(void)
+{
+	/* The below GLs are according to the Orion Errata document */
+	/*
+	 * Clear interrupt cause and mask
+	 */
+	wrl(USB_CAUSE, 0);
+	wrl(USB_MASK, 0);
+
+	/*
+	 * Reset controller
+	 */
+	wrl(USB_CMD, rdl(USB_CMD) | 0x2);
+	while (rdl(USB_CMD) & 0x2);
+
+	/*
+	 * GL# USB-10: Set IPG for non start of frame packets
+	 * Bits[14:8]=0xc
+	 */
+	wrl(USB_IPG, (rdl(USB_IPG) & ~0x7f00) | 0xc00);
+
+	/*
+	 * GL# USB-9: USB 2.0 Power Control
+	 * BG_VSEL[7:6]=0x1
+	 */
+	wrl(USB_PHY_PWR_CTRL, (rdl(USB_PHY_PWR_CTRL) & ~0xc0)| 0x40);
+
+	/*
+	 * GL# USB-1: USB PHY Tx Control - force calibration to '8'
+	 * TXDATA_BLOCK_EN[21]=0x1, EXT_RCAL_EN[13]=0x1, IMP_CAL[6:3]=0x8
+	 */
+	wrl(USB_PHY_TX_CTRL, (rdl(USB_PHY_TX_CTRL) & ~0x78) | 0x202040);
+
+	/*
+	 * GL# USB-3 GL# USB-9: USB PHY Rx Control
+	 * RXDATA_BLOCK_LENGHT[31:30]=0x3, EDGE_DET_SEL[27:26]=0,
+	 * CDR_FASTLOCK_EN[21]=0, DISCON_THRESHOLD[9:8]=0, SQ_THRESH[7:4]=0x1
+	 */
+	wrl(USB_PHY_RX_CTRL, (rdl(USB_PHY_RX_CTRL) & ~0xc2003f0) | 0xc0000010);
+
+	/*
+	 * GL# USB-3 GL# USB-9: USB PHY IVREF Control
+	 * PLLVDD12[1:0]=0x2, RXVDD[5:4]=0x3, Reserved[19]=0
+	 */
+	wrl(USB_PHY_IVREF_CTRL, (rdl(USB_PHY_IVREF_CTRL) & ~0x80003 ) | 0x32);
+
+	/*
+	 * GL# USB-3 GL# USB-9: USB PHY Test Group Control
+	 * REG_FIFO_SQ_RST[15]=0
+	 */
+	wrl(USB_PHY_TST_GRP_CTRL, rdl(USB_PHY_TST_GRP_CTRL) & ~0x8000);
+
+	/*
+	 * Stop and reset controller
+	 */
+	wrl(USB_CMD, rdl(USB_CMD) & ~0x1);
+	wrl(USB_CMD, rdl(USB_CMD) | 0x2);
+	while (rdl(USB_CMD) & 0x2);
+
+	/*
+	 * GL# USB-5 Streaming disable REG_USB_MODE[4]=1
+	 * TBD: This need to be done after each reset!
+	 * GL# USB-4 Setup USB Host mode
+	 */
+	wrl(USB_MODE, 0x13);
+}
+
-- 
1.5.3.3